Toshiba Vf Fs1 Instruction Manual

2014-12-13

• Cover
• I. Safety precautions
• II. Introduction
• Contents
• 1. Read first
  • 1.1 Check product purchase
  • 1.2 Contents of the product
  • 1.3 Names and functions
  • 1.4 Notes on the application
• 2. Connection
  • 2.1 Cautions on wiring
  • 2.2 Standard connections
  • 2.3 Description of terminals
• 3. Operations
  • 3.1 Simplified Operation of the VF-FS1
  • 3.2 How to operate the VF-FS1
• 4. Basic VF-FS1 operations
  • 4.1 Flow of status monitor mode
  • 4.2 How to set parameters
• 5. Basic parameters
  • 5.1 Setting acceleration/deceleration time
  • 5.2 Specifying an operation mode, using parameters
  • 5.3 Selection of operation mode
  • 5.4 Meter setting and adjustment
  • 5.5 Standard default setting
  • 5.6 Forward/reverse run selection (Operation panel operation)
  • 5.7 Maximum frequency
  • 5.8 Upper limit and lower limit frequencies
  • 5.9 Base frequency
  • 5.10 Selecting control mode
  • 5.11 Manual torque boost - increasing torque boost at low speeds
  • 5.12 Setting the electronic thermal
  • 5.13 Preset-speed operation (speeds in 7 steps)
• 6. Extended parameters
  • 6.1 Input/output parameters
  • 6.2 Input signal selection
  • 6.3 Terminal function selection
  • 6.4 Basic parameters 2
  • 6.5 Frequency priority selection
  • 6.6 Operation frequency
  • 6.7 DC braking
  • 6.8 Auto-stop in case of lower-limit frequency continuous operation
  • 6.9 Jump frequency - jumping resonant frequencies
  • 6.10 Bumpless operation
  • 6.11 PWM carrier frequency
  • 6.12 Trip-less intensification
  • 6.13 Droop control
  • 6.14 Conducting PID control
  • 6.15 Setting motor constants
  • 6.16 Acceleration/deceleration time 2
  • 6.17 Protection functions
  • 6.18 Forced fire-speed control function
  • 6.19 Adjustment parameters
  • 6.20 Operation panel parameter
  • 6.21 Communication function (Common serial)
  • 6.22 Parameters for options
  • 6.23 Permanent magnetic motors
• 7. Applied operation
  • 7.1 Setting the operation frequency
  • 7.2 Setting the operation mode
• 8. Monitoring the operation status
  • 8.1 Status monitor mode
  • 8.2 Display of trip information
• 9. Measures to satisfy the standards
  • 9.1 How to cope with the CE directive
  • 9.2 Compliance with UL Standard and CSA Standard
• 10. Peripheral devices
  • 10.1 Selection of wiring materials and devices
  • 10.2 Installation of a magnetic contactor
  • 10.3 Installation of an overload relay
  • 10.4 Optional external devices
• 11.Table of parameters and data
  • 11.1 User parameters
  • 11.2 Basic parameters
  • 11.3 Extended parameters
• 12. Specifications
  • 12.1 Models and their standard specifications
  • 12.2 Outside dimensions and mass
• 13. Before making a service call - Trip information and remedies
  • 13.1 Trip causes/warnings and remedies
  • 13.2 Restoring the inverter from a trip
  • 13.3 If the motor does not run while no trip message is displayed ...
  • 13.4 How to determine the causes of other problems
• 14. Inspection and maintenance
  • 14.1 Regular inspection
  • 14.2 Periodical inspection
  • 14.3 Making a call for servicing
  • 14.4 Keeping the inverter in storage
• 15. Warranty
• 16. Disposal of the inverter
• Buck cover