Touchtronics 1000TR Remote Control Transmitter User Manual NST11424 2 F

Touchtronics Inc Remote Control Transmitter NST11424 2 F

Exhibit D Users Manual per 2 1033 b3

Radio Frequency (RF)Remote Control SystemService ManualPOWERTouch 1200Manual NST11424-22010-04-05  Rev F57315 Nagy DriveElkhart, IN 46517T T Iouch ronics,  nc. Ph:  800-294-2570Fx:  574-293-1611www.touchtronics.comtouchtronics@touchtronics.com1230-RHarness w/Sealing GasketSealed Receiver:Moisture & DustModel # P12xx-R Sealed(see pg 2 for model number chart)   Range              -     300 Feet Typical                           -     Up to 600 Feet      Output             -     4 Relays   Optional           -     7 Relays      Input                -     2 (+12v) A1 & A2   Optional           -     6 (+12v or Ground) B1 - B6   .   Frequency       -     433MHz   Codes              -     Rolling Codes                           -     Secure Encryption   Voltage            -     12VDC                           -     24VDC      Current            -     5 Amps Max per Output                           -     10 Amp Input - Standard                           -     30 Amp Input - Optional      Antenna           -     Fixed - Standard (shown)   Optional           -     TNC Whip                           -     Flex Whip / Roof Mount                           -     Flex Whip / Glass Mount      Harness           -     9” Standard, 14 pin   Battery            -     All transmitter styles (except TR style)                          -     Coin Style, Lithium, CR2032                          -     100,000 1-second pulses                          -     10 year shelf life                          -     TR Style - 2 x “AA” BatteriesSystem SpecificationsP1000-TM1 P1000-TM2 P1000-TM4P1000-TK1 P1000-TK2 P1000-TK4P1000-TF2 P1000-TF2-LK P1000-TF4P1000-TX2 P1000-TX4 P1000-TX6P1000-TX2S P1000-TX4S P1000-TX6SNo ON/OFF SwitchWith ON/OFF SwitchP1000-TF6TK, TF & TR SeriesSealedTransmittersP1000-TR4 P1000-TR3 P1000-TR2
Receiver InstallationDetermine mounting location of receiver and antenna - typically under the dash or behind a wall.Antenna Installation1.  The antenna must be installed in an open, non-metal area in order to receive RF (radio frequency) transmissions.2.  Antenna range will be reduced if located:  A)  within 6 feet of a large motor  B)  near large bundles of wires  C)  near other RF devices  D)  touching any metalTo Increase Antenna Range  A)  Install exterior mount NMO Antenna See page 4 for accessory antenna optionsEach time a button is pressed on the transmitter,  the corresponding output will turn On.  For example, if button #1 is pressed, output #1 will turn On as long as the button is held.If an input signal is sent to inputs A1 or A2, or any inputs B1 - B6, the corresponding output will turn On as long as the signal is present.  (A1 or B1 = Output #1 is ON.  A2 or B2 = Output #2 is ON)Each output is factory set as momentary.  To change output from momentary to latching (push on / push off) see DIP Switch options detail on page 3.ENROLLING NEW TRANSMITTERS - Self-Learning Receiver1.  Remove and reconnect power to unit.  This will place unit into LEARN mode for 5-seconds.2.  Press any button on transmitter once.  Wait 5-seconds and confirm the transmitter has been enrolled by pressing any button and verifying the correct output turned ON.OR1.  Remove cover from receiver enclosure.2.  Locate LEARN switch (*small, push-button style switch located in the corner of the printed circuit board).3.  Press and release the LEARN switch     The Red LEARN LED next to the switch will flash4.  Press any button on NEW transmitter.6.  Red LEARN LED double blinks to confirm enrollment.7.  Press any button on the new transmitter to confirm that the new transmitter code has been enrolled.  8.  Replace receiver enclosure cover.Erasing Enrolled Codes1.  Press and hold the LEARN switch (*see # 2 above) for 10-seconds.2.  Red status LED will flash while holding LEARN switch3.  Release LEARN switch when Red LED double flashes to confirm ALL transmitter codes are erased.System OperationCode EnrollmentInstallation1210-R1211-R1212-R1213-R1220-R1221-R1222-R1223-R1230-R1231-R1232-R1233-R1240-R1241-R1242-R1243-RReceiverModel4 - Relays7 - Relays12VDC24VDC30AConnectorFixedAntennaTNCAntennaA1 & A2 Switch InputsB1 - B6 Switch InputsInputStatus LEDsSealed Receiver Model Number ChartPage -2-
ONOFF1Out# 1DIP Switch Options (DIP switch located on PCB inside receiver enclosure)ONOFFOut# 3Out# 2Out# 4Out# 5Out# 62345678DIP Switches 1 - 6 control outputs 1 - 6 respectively:     OFF = Momentary (Standard)     ON = Latching (Optional)#10 Screw#10 Star Washer#10 Ring TerminalVehicle FrameScrape paint and clean area before installing ground screw.A loose chassis ground connection WILL cause intermittent operation!Call factory for more information on other DIP switch options, including hydraulic pump, cascade and courtesy lights.ANTENNA (FIXED or TNC)Output 1J2-8Output 2J2-9Output 3J2-10Output 4J2-11Output 6J2-13Output 5J2-12Output 7J2-14Switch Input A2, J2-2Switch Input A1, J2-1Logic Power, J2-4Logic Ground, J2-3LOGIC123456789101112131412123456WHT/REDGRY/REDBLK/WHTRED/WHTNOT USEDREDREDYELORGBLUGRNPNKVIOTANREDNOT USEDYEL/BLKORG/BLKBLU/BLKGRN/BLKPNK/BLKVIO/BLK+12V / A1+12V / A2CHASSIS GROUND+12V LOGIC POWERPOWER / 5 AMPPOWER / 5 AMPOUTPUT 1 - 5 AMP (+)OUTPUT 2 - 5 AMP (+)OUTPUT 3 - 5 AMP (+)OUTPUT 4 - 5 AMP (+)OUTPUT 5 - 5 AMP (+)OUTPUT 6 - 5 AMP (+)OUTPUT 7 - 5 AMP (+) POWER / 30 AMP+12v or GND / B1+12v or GND / B2+12v or GND / B3+12v or GND / B4+12v or GND / B5+12v or GND / B6STANDARDRELAYS 1-4OPTIONALRELAYS 5-7J3J2J1ALL INPUTS, B1-B6, ARELOGIC SIGNALS (1mA)ACTIVE WITH EITHER+12V OR GROUND.INPUT A1, A2Logic Signals (1mA)BATTERYBATTERY10 AMPBATTERY30 AMPOptional / Customer SuppliedOptional / Customer SuppliedOutput 7Used only with DIP SwitchOption 7 & 8Call Factory forCustom ApplicationsTouchTronics, Inc.1-800-294-2570BATTERYAll output signals can be either +12VDC or Ground.For +12VDC output signals, supply +12vdc to:J1-1, J2-6 and J2-7For Ground output signals, supply +12vdc to:J1-1 and J2-7Page -3-123456789101112131412123456SealingGasket
Limited One (1) Year Warranty1)  Each individual product is warranted under the  TouchTronics Limited Warranty program for 1 full year from date of purchase or a  maximum of 2 years from the date of manufacture.2)  No product will be covered under the  TouchTronics Limited Warranty program that has a manufacture date older than 2 years.3)  To receive technical support or warranty service, call our technical support center during regular business hours.  1-800-294-25704)  To enable our technical support staf f to better serve you, please have the following information available when you call.PurchaseInstallationDate Of:Dealer NameDealer PhoneMake / ModelVehicle Information:Model NumberSerial NumberProduct Information:Fill in all pertinent information at the time of purchase or installation.TouchTronics, Inc. Warranty Policies and Procedures© 2005 TouchTronics, Inc.  All Rights Reserved.  TouchTronics, the TouchTronics logo, and other TouchTronics marks are owned by TouchTronics and may be registered.  TouchTronics assumes no responsibility for any errors that may appear in this manual.  Information contained herein is subject to change without notice.FCC Compliance and Advisory Statement. This hardware device complies with Part 15 of the FCC Rules.  Operation is subject to the following two conditions:  1) this device may not cause harmful interference, and 2) this device must accept any interference received, including interference that may cause undesired operation.  This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.  These limits are designed to provide reasonable protection against harmful interference in a residential installation.  This equipment generates, uses, and can radiate radio frequency energy and, if not installed or used in accordance with the instructions, may cause harmful interference to radio communications.  However, there is no guarantee that interference will not occur in a particular installation.  If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:  1) reorient or relocate the receiving antenna; 2) increase the separation between the equipment and the receiver 3) connect the equipment to an outlet on a circuit different from that to which the receiver is connected; 4) consult the dealer or an experienced radio/TV technician for help.  Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.  Where shielded interface cables have been provided with the product or specified additional components or accessories elsewhere defined to be used with the installation of the product, they must be used in order to ensure compliance with FCC regulations.Canadian DOC Statement.  This digital device does not exceed the Class B limits for radio noise emissions from digital apparatus specified in the interference-causing equipment standard entitled “Digital Apparatus,” ICES-003 of the Department of Communications.This device complies with RSS-210 of Industry Canada.  Operation is subject to the following two conditions:  1) this device may not cause interference, and 2) this device must accept any interference, including interference that may cause undesired operation of the device.© 2005 TouchTronics, Inc.  Tous droits réservés.  TouchTronics, le logo TouchTronics et les autres marques TouchTronics sont la propriété exclusive de TouchTronics et sont susceptibles d'être des marques déposées.  Toutes les autres marques sont la propriété exclusive de leurs détenteurs respectifs.  TouchTronics décline toute responsabilité en cas d'erreurs dans ce manuel.  Les informations énoncées dans le présent document peuvent faire l'objet de modifications sans avis préalable. Déclaration FCC.  Cet équipement a été testé et déclaré conforme à la section 15 du règlement de la FCC.  Son fonctionnement est soumis aux conditions suivantes:  1) l'équipement concerné ne doit pas causer d'interférences dangereuses, et 2) il doit accepter toute interférence reçue, y compris les interférences risquant d'engendrer un fonctionnement indésirable.  Cet équipement a été testé et déclaré conforme aux limitations prévues dans le cadre de la catégorie B des appareils numériques défini par la section 15 du règlement de la FCC.  Ces limitations sont stipulées aux fins de garantir une protection raisonnable contre les interférences gênantes en installation résidentielle.  Cet équipement génère, utilise et diffuse des ondes radio, et s'il n'est pas installé ni utilisé en conformité avec les instructions dont il fait l'objet, peut causer des interférences gênantes avec les communications radio.  Cependant, nous ne pouvons vous garantir qu'une interférence ne se produira pas dans une installation particulière.  Si cet équipement produit des interférences graves lors de réceptions radio ou télévisées qui peuvent être détectées en allumant et en éteignant l'équipement, vous êtes invités à les supprimer de plusieurs manières:  1) Réorienter ou déplacer l'antenne de réception; 2) Augmenter la distance séparant l'équipement et le récepteur 3) Connecter l'équipement à un circuit différent de celui auquel le récepteur est connecté; 4) Contacter votre revendeur ou un technicien radio/TV qualifié.  Toutes modifications ou tous changements effectués sans l'accord exprès de la partie responsable de la conformité aux normes pourraient contraindre l'utilisateur à ne plus utiliser son équipement.  Afin d'assurer la conformité avec les règlements FCC, les câbles d'interface blindés fournis avec le produit doivent être utilisés, ainsi que tout autres composants ou accessoires également spécifiés, lors de l'installation du produit.Déclaration du Ministère des Communications Canadien.  Cet appareil numérique est conforme aux limitations concernant l'émission d'interférences radio par des appareils numériques de catégorie B, telles que stipulées dans le cadre de la norme Appareils numériques ICES-003 édictée par le Ministère canadien de l'industrie.Cet équipement a été déclaré conforme à la norme RSS-210 édictée par le Ministère canadien de l'industrie.  Son fonctionnement est soumis aux conditions suivantes:  1) l'équipement concerné ne doit pas causer d'interférences, et 2) il doit accepter toute interférence reçue, y compris les interférences risquant d'engendrer un fonctionnement indésirable.Technical Support Via Web Site / Emailwww.touchtronics.comTechsupport@touchtronics.com or‘Contact Request’ link on the web pageTechnical Support Indiana Local    1-574-294-2570Toll Free            1-800-294-2570Fax                     1-574-293-1611Numbers Sales SupportPhone    1-800-294-2570Fax         1-574-293-1611Email     sales@touchtronics.com              Page -4-Section One     Seller will warrant any product originally manufactured or assembled and sold by seller for a period of up to TWO YEARS (24 months) from the original date of manufacture or ONE YEAR (12 months) from the original retail sale or O.E.M. in-service date.Section Two     The following are in lieu of all warranties; expressed; implied; or statutory, including but not limited to, any implied warranty of merchantability of fitness for a particular purpose and of any other warranty obligation on the part of seller.  Seller, except as otherwise hereinafter provided, warrants the goods against faulty workmanship or defective materials for a period of up to TWO YEARS (24 months) from the original date of manufacture or ONE YEAR (12 months) from the original retail or O.E.M. in-service date.     Seller’s sole and exclusive liability shall be (at seller’s option) to repair; replace; or credit buyer for such goods which are returned by buyer during the applicable warranty period set forth above, provided that (I) seller is promptly notified in writing or by phone upon discovery by buyer that such goods failed to conform and an explanation of any alleged deficiencies, (II) such goods are returned to seller, (III) sellers examination of such goods shall disclose that such alleged deficiencies actually exist and were not caused by accident, misuse, neglect, alteration, improper installation, unauthorized repair or improper testing.  If seller elects to repair or replace such goods, seller shall have a reasonable time to make such repairs or replace such goods.     Seller’s warranties as herein above set forth shall not be enlarged, diminished, or affected by, and no obligation or liability shall arise or grow out of, sellers rendering of technical advice or service.Damage to products caused by the customer or during installation cannot be claimed under this warranty.   All devices returned that are not covered under the seller’s warranty policy, will be charged a minimum of $25.00 for evaluation plus additional charges for components and labor to repair the device not to exceed the original selling price.   Seller considers the following to be typical examples of customer or installation damage: burned or broken traces on the printed circuit board, burned or damaged components, dirt or water residue on the printed circuit board or inside the case, modifications by the customer, broken cases or housings and dead batteriesSection Three     A return material authorization number (RMA) must be issued by seller before any product is returned for evaluation or repair.  Warranty repairs must be completed at authorized repair facilities.ANT11405-1ANT10430-2ANT11514-1Accessories Minimum Orders:  $25.00TNC, Wire Whip AntennaGlass Mount Antenna Kit, 14 foot cableFlex Whip Antenna Kit, 10 foot cable, roof mountCall Factory for Current Pricing and Availability

Navigation menu