TranSystem P07-1111-02 Subscriber Unit User Manual Installation M
TranSystem Subscriber Unit Installation M
Users Manual
| Download: |  |
| Mirror Download [FCC.gov] | |
| Document ID | 386327 |
| Application ID | qdLrM5Tmnkr4JgEowKLFYQ== |
| Document Description | Users Manual |
| Short Term Confidential | No |
| Permanent Confidential | No |
| Supercede | No |
| Document Type | User Manual |
| Display Format | Adobe Acrobat PDF - pdf |
| Filesize | 5.89kB (73615 bits) |
| Date Submitted | 2004-01-05 00:00:00 |
| Date Available | 2003-12-31 00:00:00 |
| Creation Date | 2003-11-25 09:45:37 |
| Producing Software | Acrobat Distiller 5.0.5 for Macintosh |
| Document Lastmod | 2003-11-25 09:45:37 |
| Document Title | Microsoft Word - Installation M |
| Document Creator | Microsoft Word: AdobePS 8.7.3 (301) |
| Document Author: | Tom Cokenias |
Installation Manual of 700MHz Transceiver P07-1111-2-24 Nov. 2003 UHF Transystem, Inc. www.transystem.com.tw 1. Before you unpack the box, please check if there are one P071111-2-24 transceiver and one mounting bracket inside. 2. To install the transceiver onto a mast, you will need: a. An indoor power inserter/adapter (provided by TSI) b. A 75 ohm coaxial cable (RG 6, RG 7 or RG 11) to run up the mast to the transceiver c. A 75 ohm UHF Yagi antenna of proper gain d. A short 75 ohm (RG-59, RG 6, RG7 or RG 11) coaxial cable to connect the transceiver with the antenna 3. Installation: (refer to Fig. 1) a. Install the Yagi antenna onto the mast. b. On the same mast use the included mounting bracket to install the transceiver c. Connect the transceiver’s antenna port to the Yagi antenna by a short 75 ohm Male-to-male coaxial cable. Use a waterproof tape to seal the transceiver’s F-connector port. d. Connect the DC+IF port of the transceiver to where the wireless modem is indoors by a long 75 ohm coaxial cable. Also use a water-proof tape to seal the transceiver’s Fconnector port. Note that unless the modem can power the transceiver through the coaxial cable, you will need to install the wall mount adapter/power inserter (provided by TSI) between the transceiver and the modem. e. Turn on the power adapter and use either the modem’s utility software or a CATV signal strength meter to align the Yagi antennas’ direction toward where the headend antenna site is to get the strongest downlink signal. f. Fix the antenna direction. Install the necessary antilightning grounding rod to protect lightning strike. Fig. 1: Installation of transceiver with UHF Yagi antenna NOTE: Cable modem “Channel Size” settings must be configured so that channel center frequencies at band edge will meet the limits in the following table: Data rate kSym/sec 320 640 1280 Lowest fc QAM 710.4 MHz 710.7 MHz 711.7 MHz Hi ghest fc, QAM 715.6MHz 715.4 MHz 715.1 MHz Low est fc, QPSK 710.3 MHz 711 MHz 712 MHz Hi ghest fc., QPSK 715.6 MHz 715.5 MHz 715.1 MHz FCC RF Exposure Information: The licensee is responsible for determining that antenna installation will result in RF exposure levels to persons being in compliance with the requirements of section 1.1307 of FCC Rules.
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.3 Linearized : No Create Date : 2003:11:25 09:45:37-08:00 Modify Date : 2003:11:25 09:45:37-08:00 Page Count : 3 Creation Date : 2003:11:25 17:45:37Z Mod Date : 2003:11:25 17:45:37Z Producer : Acrobat Distiller 5.0.5 for Macintosh Author : Tom Cokenias Metadata Date : 2003:11:25 17:45:37Z Creator : Tom Cokenias Title : Microsoft Word - Installation MEXIF Metadata provided by EXIF.tools