Trane Uni Fan Coil And Force Flo Installation Maintenance Manual UNT SVX07D EN (27 Apr 2012)

2015-04-02

• Warnings, Cautions and Notices
• Model Number Descriptions
• General Information
• Pre-Installation
  • Receiving and Handling
  • Jobsite Storage
  • Installation Preparation
  • Service Access
  • Pre-Installation Checklist
• Dimensions and Weights
  • Available Models
  • Factory-Installed Piping Packages
  • Vertical Concealed, Model A
  • Vertical Cabinet, Model B
  • Horizontal Concealed, Model C
  • Horizontal Cabinet, Model D
  • Horizontal Recessed, Model E
  • Vertical Wall Hung Cabinet, Model F (Force-Flo Units Only)
  • Vertical Recessed, Model H
  • Vertical Slope Top, Model J
  • Low Vertical Concealed, Model K
  • Low Vertical Cabinet, Model L
  • Inverted Vertical Cabinet, Model M (Force-Flo Units Only)
  • Inverted Vertical Recessed, Model N (Force-Flo Units Only)
  • Compact Concealed, Model P
  • Fan-Coil Coil Connections
  • Force-Flo Coil Connections
  • Fresh Air Opening Locations
  • Wall Box
  • Projection Panel
• Installation—Mechanical
  • Duct Connections
  • Piping Considerations
• Installation—General
  • Installing the Unit
    • Vertical Units
    • Horizontal Units
    • Cabinet Units
    • Recessed Units
  • Installation Checklist
• Installation—Controls
  • General Information
    • Control Options (Including Factory- Installed)
  • Installing Wall-Mounted Wired Sensors
    • Location Considerations
    • Location Considerations for Wireless zone sensors
    • Fan Mode Switch Installation
    • Zone Sensor Installation
• Installation—Electrical
  • Unit Wiring Diagrams
  • Supply Power Wiring
  • Electrical Grounding Restrictions
  • Wall-Mounted Control Interconnection Wiring
• ECM Overview and Setup
  • Overview
  • General Information
    • Trane BLDC Motor
    • ECM Engine Controller
    • Standard Adapter Board
    • CSTI Adapter Board
  • Installation and Initial Setup
    • Installation and Initial Setup
    • Adjustment and Configuration of the Engine Board
    • Status Display
    • Initial Setup and Configuration
  • Configuration
    • Configuring the ECM Engine Controller
    • Configuring the ECM Engine Board
• Wired Controllers—Communication Wiring
  • Wiring Installation (ZN510 and ZN520)
    • Device Addressing
    • Recommended Communication Wiring Practices
  • Wiring Installation (Tracer UC400)
    • Wiring Overview Outline
    • General Instructions
    • BACnet MS/TP Link
    • Power Supply
• Wireless Sensors
  • Address Setting
  • Observing the Receiver for Readiness to Associate
  • Associating the Sensor to the Receiver
  • Testing Signal Strength and Battery Status
  • Configuring the Wireless Display Sensor (Model WDS only)
  • Sensor Operations
  • Wireless Sensor Specifications
• Pre-Start
  • Pre-Startup Checklist
• Startup
  • Tracer ZN510 and ZN520 Unit Startup
  • Tracer UC400 Unit Startup
  • General Information
  • Fan Mode Switch Operation
  • Tracer ZN010 & ZN510 Operation
  • Tracer ZN520 Operation
  • UC400 Controller Operation
  • Sequence of Operation: Tracer ZN010 and ZN510
    • Binary Inputs (Tracer ZN010 and ZN510)
    • Binary Outputs (Tracer ZN010 and ZN510)
  • Tracer ZN520 Sequence of Operation
    • Cooling Operation (Tracer ZN520)
    • Fan Mode Operation (Tracer ZN520)
  • UC400 Sequence of Operation
    • Power-up Sequence (UC400)
    • Random Start (UC400)
    • Occupancy Modes (UC400)
    • Timed Override Control (UC400)
    • Zone Temperature Control (UC400)
    • Discharge Air Tempering (UC400)
    • Heating or Cooling Mode (UC400)
    • Entering Water Temperature Sampling Function (UC400)
    • Fan Operation (UC400)
    • Exhaust Control (UC400)
    • Valve Operation (UC400)
    • Modulating Outdoor/Return Air Damper (UC400)
    • Two-position Control Of A Modulating Outdoor Air Damper (UC400)
    • Electric Heat Operation (UC400)
    • Dehumidification Operation (UC400)
    • Peer-to-peer Communication (UC400)
    • Unit Protection Strategies (UC400)
• Maintenance
  • Maintenance Procedures
  • Replacing Motors
  • Periodic Maintenance Checklists
• Diagnostics
  • Output Testing and Diagnostics (Tracer ZN520)
  • Output Testing and Diagnostics (UC400)
    • Output Testing (UC400)
    • Diagnostics (UC400)
  • Troubleshooting (Wireless Controls)
    • Troubleshooting (Tracer ZN520)
    • Troubleshooting (UC400)
    • Troubleshooting (ECM)
    • General Information (ECM)
    • Troubleshooting Information (ECM)
• Replacing ECM Components
  • Circuit Modules Replacement Notes/Work Instructions
• ECM Application Notes
• Wiring Diagrams