Trane Voyager 12 5 To 25 Tons Installation And Maintenance Manual RT SVX49* EN Tracer™ TD Display For ReliaTel™ Controller November 2013

: Trane Trane-Voyager-12-5-To-25-Tons-Installation-And-Maintenance-Manual-684205 trane-voyager-12-5-to-25-tons-installation-and-maintenance-manual-684205 trane pdf

Open the PDF directly: View PDF .
Page Count: 36

SAFETY WARNING

Only qualified personnel should install and service the equipment. The installation, starting up, and servicing of heating, ventilating, and air-

conditioning equipment can be hazardous and requires specific knowledge and training. Improperly installed, adjusted or altered equipment

by an unqualified person could result in death or serious injury. When working on the equipment, observe all precautions in the literature and

on the tags, stickers, and labels that are attached to the equipment.

Tracer™TD-5 Display

for ReliaTel™ Controller

Installation, Operation,

and Maintenance

RT-SVX49A-EN

November 2013

© 2013Trane All rights reserved RT-SVX49A-EN

Warnings, Cautions and Notices

Warnings, Cautions and Notices. Note that warnings,

cautions and notices appear at appropriate intervals

throughout this manual. Warnings are provided to alert

installing contractors to potential hazards that could result

in death or personal injury. Cautions are designed to alert

personnel to hazardous situations that could result in

personal injury, while notices indicate a situation that

could result in equipment or property-damage-only

accidents.

Your personal safety and the proper operation of this

machine depend upon the strict observance of these

precautions.

Read this manual thoroughly before operating or servicing

this unit.

Important

Environmental Concerns!

Scientific research has shown that certain man-made

chemicals can affect the earth’s naturally occurring

stratospheric ozone layer when released to the

atmosphere. In particular, several of the identified

chemicals that may affect the ozone layer are refrigerants

that contain Chlorine, Fluorine and Carbon (CFCs) and

those containing Hydrogen, Chlorine, Fluorine and

Carbon (HCFCs). Not all refrigerants containing these

compounds have the same potential impact to the

environment.Trane advocates the responsible handling of

all refrigerants-including industry replacements for CFCs

such as HCFCs and HFCs.

Responsible Refrigerant Practices!

Trane believes that responsible refrigerant practices are

important to the environment, our customers, and the air

conditioning industry. All technicians who handle

refrigerants must be certified.The Federal Clean Air Act

(Section 608) sets forth the requirements for handling,

reclaiming, recovering and recycling of certain

refrigerants and the equipment that is used in these

service procedures. In addition, some states or

municipalities may have additional requirements that

must also be adhered to for responsible management of

refrigerants. Know the applicable laws and follow them.

ATTENTION: Warnings, Cautions, and Notices appear at

appropriate sections throughout this literature. Read

these carefully:

WARNING Indicates a potentially hazardous

situation which, if not avoided, could

result in death or serious injury.

CAUTIONsIndicates a potentially hazardous

situation which, if not avoided, could

result in minor or moderate injury. It

could also be used to alert against

unsafe practices.

NOTICE: Indicates a situation that could result in

equipment or property-damage only

accidents.

WARNING

Proper Field Wiring and Grounding

Required!

All field wiring MUST be performed by qualified

personnel. Improperly installed and grounded field

wiring poses FIRE and ELECTROCUTION hazards.To

avoid these hazards, you MUST follow requirements for

field wiring installation and grounding as described in

NEC and your local/state electrical codes. Failure to

follow code could result in death or serious injury.

WARNING

Personal Protective Equipment (PPE)

Required!

Installing/servicing this unit could result in exposure to

electrical, mechanical and chemical hazards.

• Before installing/servicing this unit, technicians

MUST put on all Personal Protective Equipment (PPE)

recommended for the work being undertaken.

ALWAYS refer to appropriate MSDS sheets and OSHA

guidelines for proper PPE.

• When working with or around hazardous chemicals,

ALWAYS refer to the appropriate MSDS sheets and

OSHA guidelines for information on allowable

personal exposure levels, proper respiratory

protection and handling recommendations.

• If there is a risk of arc or flash, technicians MUST put

on all Personal Protective Equipment (PPE) in

accordance with NFPA 70E or other country-specific

requirements for arc flash protection, PRIOR to

servicing the unit.

Failure to follow recommendations could result in death

or serious injury.

Table of Contents

RT-SVX49A-EN 3

Warnings, Cautions and Notices .......... 2

Introduction ............................. 4

Hardware ............................. 4

Power ............................. 4

Communication ..................... 4

Screen characteristics ................ 4

Touchscreen Guidelines ................ 4

Dimensions ........................... 5

Specifications and Agency Compliance ... 6

Supported Languages .................. 6

Screen Overview ...................... 7

Top Display Area .................... 7

Main Display Area ................... 7

Bottom Display Area ................. 7

Installing the Tracer™ TD-5 Display ....... 8

Packaged Contents .................... 8

Additional Mounting Parts ............. 8

Installing the TD-5 Display onto a VESA

Mounting Bracket ...................... 8

Powering up the TD-5 Display for the First

Time ................................. 9

Alarms ................................. 10

Active Alarms ........................ 10

Historic Alarms ....................... 11

Viewing Active and Historic Alarms ..... 11

Alarm Icons .......................... 12

Sorting Alarms ....................... 12

Reports ................................ 13

Custom Reports ...................... 13

Creating a Custom Report ............ 13

Editing a Custom Report ............. 15

About ............................... 16

System Report ....................... 17

Economizer/Ventilation Report ......... 18

Compressor Report ................... 18

Heating Report ....................... 19

Configuration Report .................. 19

Sensor Report ........................20

Binary Input Report ...................20

Binary Output Report ..................21

Graphs .................................22

Creating a Custom Graph ..............22

Standard Graphs ......................25

Space Temperature: .................25

Compressor Graph: ..................25

VAV System: .......................26

Economizer Graph: ..................26

Outside Air Ventilation: ..............26

CO2Graph: .........................26

Humidity Graph: ....................26

Heat Pump Graph: ...................26

Settings ................................27

Setpoints ............................27

Setup ................................28

Display Settings Screen ................29

Display Preferences .................29

Language ..........................31

Date and Time ......................31

Clean Touchscreen ..................32

Troubleshooting ........................33

Identifying and Diagnosing Issues .......33

4 RT-SVX49A-EN

Introduction

The purpose of this guide is to assist you in installing,

programming, and operating theTracer™TD-5 display,

which operates with the ReliaTel™ Controller.This guide

describes how to access the screens and the types of

information that appear on the screens.

TheTracer™TD-5 display allows you to view data and

make operational changes on the following types of

applications:

• Voyager™

• Precedent™

Hardware

TheTracer™TD-5 is a durable touch screen display that is

designed to operate in both indoor or outdoor

environments.TheTD-5 display utilizes a standard 75mm

VESA mounting pattern for installation. Alternatively, it

can be installed with a user-supplied VESA mount.

Power

TheTracer™TD-5 display is powered by 24 VAC or 24 VDC

and requires 21 VA power, which it receives through a

power cable.The display is typically connected to J10 of

the RTRM Module, but it can also be powered from an

alternate power source.

Communication

Communication is provided to theTD-5 through the RTRM

J10 connector.

Screen characteristics

The 5-inch WVGA 800 x 480 resolution touch-sensitive

color screen is LED backlit, which enables viewing in poor

light conditions including outdoor usage (with the

exception of direct sunlight).

Touchscreen Guidelines

The touch screen registers the downward pressure of a

touch. Light, quick, yet deliberate touches are most

effective.Touching with more pressure has no effect.

Recommended tools to use:

• finger

• thumb

• pencil eraser

Do not use:

• a screwdriver

• a pen

• a pencil point

• any other sharp or pointed object that might scratch

the screen surface

Introduction

RT-SVX49A-EN 5

Dimensions

32,0][3.1

42,1][7.1

154,0

][1.6

147,0

][8.5

106,4

][2.4

115,3

][5.4

Note: The power cable is permanently attached

to theTD-5 display. The power connector

provides strain relief and protection from the

Introduction

6 RT-SVX49A-EN

Specifications and Agency

Compliance

Supported Languages

TheTD-5 display supports 26 built-in languages. For help

on how to select a specific language for the display, see

“Language,” p. 31.

Specification

Input power: 24 Vac ± 15%, or 24 Vdc ± 10% 21 VA, 50 or

60 Hz

Storage

temperature:

–67°F to 203°F (–55°C to 95°C)

Humidity: Between 5% to 100% (non-

condensing)

Operating

temperature:

Temperature: –40°F to 158°F (–40°C to 70°C)

Humidity: Between 5% to 100% (non-

condensing)

Mounting weight: Mounting surface must support 0.93 lb (422

grams)

Mounting Type: VESA (75 mm x 75 mm)

Environmental

rating

(enclosure):

IP55 (dust and strong water protected)

(PN: X19070632020)

Agency Compliance

• UL916 PAZX, Open Energy Management Equipment

• UL94-5V, Flammability

• FCC CFR Title 47, Part 15.109: Class A Limit, (30 MHz – 4 GHz)

• CE EMC Directive 2004/108/EC

• CE EMC Directive 2004/108/EC

Arabic Hungarian Romanian

Chinese (Simplified) Indonesian Russian

Chinese (Traditional) Italian Spanish (Mexico)

Czech Japanese Spanish (Spain)

Dutch Korean Swedish

English Norwegian Thai

French Polish Indonesian

German Portuguese (Brazil) French Canadian

Hebrew Portuguese (Portugal)

Introduction

RT-SVX49A-EN 7

Screen Overview

There are three distinct areas on theTD-5 screens:

• Top display area

• Main display area

• Bottom display area

Top Display Area

Main Display Area

This area serves as the main task area in which you can

view custom graphics, create reports, view and take action

on alarms, and view or change display settings.

Bottom Display Area

The bottom display area contains functional buttons that

provide a link to the appropriate screen.

Figure 1. Tracer™ TD-5 display screen

Main display

area

Top display area

Bottom display

area

The Back button, when touched, returns

to the previous screen visited.

The Home button, when touched,

navigates to the Home Page. Home can be

configured. See “Display Preferences,”

p. 29.

The Header Data Point is a user-defined

data point that will appear at the top

portion of each display screen. This value

can be the present value of any point in

the TD-5. See “Header Data Point,” p. 29.

Screen brightness settings: Touch this

icon to change the display’s brightness.

Touch this button to open the Alarms

screen. When an alarm is present, this

button will flash red.

Touch this button to navigate to the

Reports screen.

Touch this button to open the Data Graphs

screen to view Graphs.

Touch this button to open the Settings

screen, which contains options for

controls, security (if enabled), and

display settings.

Language selection: Touch this icon to

select a language that will be displayed on

all screens.

8 RT-SVX49A-EN

Installing the Tracer™ TD-5 Display

This section describes installation procedures when

mounting theTracer™TD-5 display near the RTRM

module or remotely mounted up to 328 ft (100 m) by using

a field-suppled 75 mm VESA mounting bracket. Read and

observe all warning and caution statements before you

begin the installation procedure.

Packaged Contents

• One (1)Tracer™TD-5 display with permanently

attached 2.6 ft (0.8 m) power cable with male connector

• Four (4) M-4 screws

• Four (4) spacer washers

Additional Mounting Parts

• TD-5 Display Low Profile Mounting Bracket (VESA

75mm) (PN: X05010511010)

Installing the TD-5 Display onto a

VESA Mounting Bracket

TheTracer™TD-5 can be mounted near the RTRM module

in the control panel, or remotely mounted up to 328 ft

(100 m) by using a field-suppled 75 mm VESA mount.

Remote mounting requires the following additional field-

supplied components:

• A power source that will supply 24 VAC to the display

• Power cables

Many commercial 75mm VESA mounting brackets are

available, which range from a simple wall mount to tilt-

and-swivel mounts such as the one shown in Figure 2, p. 9,

or theTD-5 Display Low Profile Mounting Bracket (VESA

75mm) (PN: X05010511010).

To install onto a VESA mounting bracket:

1. Disconnect power at the circuit breaker and perform

lockout/tagout procedures.

2. Mount the VESA mounting bracket according to

manufacturer’s instructions.

3. Position theTD-5 display 1onto the VESA mounting

bracket 2and align the four mounting holes with the

bracket while inserting and hand-tightening the four

M-4 screws. (Some brands ofVESA mounting brackets

may require the use of the four spacer washers to allow

the M-4 screws to tighten properly.)

4. Securely tighten the M-4 screws using a Phillips

screwdriver.

WARNING

Hazardous Voltage!

Disconnect all electric power, including remote

disconnects before servicing. Follow proper lockout/

tagout procedures to ensure the power can not be

inadvertently energized. Failure to disconnect power

before servicing could result in death or serious injury.

Installing the Tracer™ TD-5 Display

RT-SVX49A-EN 9

Powering up the TD-5 Display for

the First Time

After completing the installation instructions in “Installing

theTracer™TD-5 Display,” p. 8,TheTD-5 display can be

powered up.

Before applying power to theTD-5 Display, verify that the

RTRM Module is powered up.

Upon successful power up, theTD-5 Display will default to

the configured home screen.The System Report is the

factory default.

Important: Do not attempt to update theTD-5 Display

from a connection type other than a USB.

Figure 2. Example VESA mounting

12

10 RT-SVX49A-EN

Alarms

Alarms appear on theTracer™TD-5 display immediately

upon detection.Touch the Alarms button in the bottom

display area to view the Alarms screen.

Active Alarms

Figure 3, p. 10 shows the Active Alarms screen and

commonly used functions. Configuration is not required in

order for points in alarm to appear in the Active Alarms

screen. When the alarm clears and the point returns to

normal, the alarm will automatically be removed from the

list.The number of active alarms is displayed in the top

right portion of the screen. When an active alarm is

present, the alarm button at the bottom of the screen will

flash.

The Alarms screen defaults to Active Alarms.The Active

Alarms button has a shaded appearance which indicates

that you are viewing active alarms.

Figure 3. Active alarms screen

Number of active alarms

Active Alarms

button

Alarm severity

Sortable

columns

Alarms

RT-SVX49A-EN 11

Historic Alarms

On the Alarms screen, touch the Historic Alarms button to

view all alarms, commonly referred to as the event log (see

Figure 4, p. 11).

Viewing Active and Historic

Alarms

•Active alarms:These are alarms that require attention.

All alarms that are currently active appear when you

view this category. Active alarms are not reset by way

of the display. Active alarms will clear automatically

when the condition causing the alarm is removed.

•Historic alarms: Historic alarms appear when you view

this category.The alarms are listed in chronological

order.

Alarm Severity

A color-code icon representing the severity of each alarm

is shown under the severity (!) column. For a description

of the five alarm icons, see Table 1, p. 12.

Sortable Alarms

You can sort active alarms by touching one of the column

headers. Choose to sort by severity (!), date and time,

point name, or description.

Figure 4. Historic alarms screen

Sortable

columns

Alarm severity

Historic Alarms button

Number of historic

alarms

Alarms

12 RT-SVX49A-EN

Alarm Icons

Alarms icons appear in the left-most column of the alarms

screen.They are identifiable by their shape and color.

Sorting Alarms

To sort alarms by a category other than date and time,

touch one of the other column headings in the table.The

column heading responds by changing to blue, and the

alarms table re-sorts according to the blue column

heading. By touching the blue column heading again, the

column will change the sort direction.

• Severity (!): Active alarms are at the top, followed by

the most severe, followed by the most recent.

• Date andTime (the default sort): Most recent alarms

are at the top.

• Description: Alarms are sorted alphabetically by

description.

Table 1. Alarm icons

Active

Alarm Icons Notification Class

Critical

Service Required

Information

Note: Notifications classes are configured in point alarm settings section

in Tracer TU.

Table 2. List of alarms

Space Temp Sensor Failure Outdoor Temp Sensor Fail

Compressor 1 HPC Lockout Compressor 1 LPC Lockout

Comp 1 Disable Input/LPC Compressor 2 HPC Lockout

Compressor 2 LPC Lockout Comp 2 Disable Input/LPC

Smoke Detector Heat Failure

Dirty Filter Supply Fan Failure

Emergency Stop Frostat™ Trip

Mixed Air Temp Sensor Fail OA Humidity Sensor Failure

Return Air Temp Sensor Fail Return Air RH Sensor Failure

Coil Temp Sensor #1 Fail Demand Defrost Fault A

Demand Defrost Fault B Demand Defrost Fault C

Demand Defrost Fault D Defrost Default Mode

Local Cool Setpoint Fail Local Heat Setpoint Fail

Vent Override – Purge Vent Override – Exhaust

Vent Override – Pressurize Drain Pan Overflow

Freezestat Tripped Supply Air Temp Sensor Fail

CO2 Sensor Failure CO2 Setpoint Failure

Space Humidity Sensor Fail Dehumid Setpoint Failure

Air Flow Sensor Fail Min OA Flow Setpoint Fail

Space Pressure Setpoint Fail Space Pressure Sensor Fail

Heating High Temp Limit Open Flame Rollout Switch Open

Inducer Proving Switch Fail No Flame Sensed on heat call

Flame Sensed w/Gas Valve Off Gas Heat Module Failure

Economizer Actuator Fault Morning Warmup Setpoint Fail

SA Reset Amount Failure SA Temp Cool Setpoint Fail

SA Temp Heat Setpoint Fail SA Reset Setpoint Failure

SA Press Setpoint Fail SA Pressure Deadband Fail

Supply Air Press Sensor Fail SA High Press Limit

SA Pressure PWM Fault Comp 1 Disable Input/HPC

Comp 2 Disable Input/HPC CO2 Low Limit Setpoint Fault

Exh/Ret Fan Proving Failure RTOM Comm Fail

RTEM Comm Fail RTAM Comm Fail

RTVM Comm Fail RTCM Comm Fail

SA Reheat Setpoint Failure RTDM Comm Fail

Space Press Deadband Fail Mod Dehumid Config

Ent Evap Temp Sensor Fail Coil Temp Sensor #2 Fail

SA Temp Heat Setpoint Fail Demand Defrost Fault A Ckt 2

Demand Defrost Fault B Ckt 2 Demand Defrost Fault C Ckt 2

Defrost Default Mode Ckt 2 Demand Defrost Fault A Ckt 1

Demand Defrost Fault B Ckt 1 Demand Defrost Fault C Ckt 1

Defrost Default Mode Ckt 1 Exhaust Fan Setpoint Fail

IGN1 Communications Timed out IGN2 Communications Timed out

DCV Min Position Setpoint Fail (@

Full Fan Speed) Design Min Position Setpoint Fail

(@ Full Fan Speed)

Enthalpy Setpoint Fail Design Min Position at Minimum

Fan Speed Fail

DCV Min Position at Minimum Fan

Speed Fail Design Min Position at Midpoint

Fan Speed Fail

DA Cool Setpoint Fail PWM Max Fan Spd Setpt Fail

Compressor 3 HPC Lockout Compressor 3 LPC Lockout

Comp 3 Disable Input/LPC Comp 3 Disable Input/HPC

Power on Reset TD-5 Loss of Comm with RTRM

Table 2. List of alarms (continued)

RT-SVX49A-EN 13

Reports

You can use theTracer™TD-5 Display to view a variety of

reports and create and edit custom reports.

Touch the Reports button in the bottom display area to

view the Reports screen.The Reports screen contains the

following buttons:

Custom Reports

You can create up to three custom reports using the

Tracer™TD-5 Display

Creating a Custom Report

1. Navigate to the Reports screen, then touch one of the

three custom report buttons.

The Custom Report (1, 2, or 3) screen appears.

2. Touch the Edit button.

The Edit Custom Report screen appears (Figure 6,

p. 14).

Table 3. Representation of screen below

Custom Report 1 System Report About

Custom Report 2 Compressor Report Sensor Report

Custom Report 3 Operating Modes Configuration Report

Economizer/

Ventilation Report Heating Report

Binary Input Report Binary Output Report

Figure 5. Reports screen

Reports

14 RT-SVX49A-EN

3. Use the up and down arrow buttons to select a point.

Add items by touching the item that is highlighted

blue, then touch the Add button.

4. Continue adding values to your report. When you are

finished, touch the Save button.

The Custom Report screen, populated with your

selected values, appears (Figure 7, p. 14).

To view the items in the selected list, touch a value in

this list and use the up and down arrows to the right of

the list.To change the location of an item in the list,

select the item and then use the up and down arrows

above the table to move the items.

Figure 6. Creating a custom report

Figure 7. New custom report screen

Reports

RT-SVX49A-EN 15

Editing a Custom Report

1. Touch Reports to view the Reports screen.

2. Touch the report that you want to edit.

Follow steps 2 through 4 in “Creating a Custom

Report,” p. 13. to complete your edits.

Changing the Order of Items in a Custom

Report

Items in a custom report can be rearranged according to

personal preference by using the editing tools as

described in Editing a Custom Report.

For example, you created the custom report shown in

Figure 7, p. 14, but would prefer to move item “Diagnostic:

Space Static Pressure Failure” to the top left portion of the

report.

To change the order for the example described above:

1. Touch the Edit button on the Custom Report screen.

2. Use the arrow buttons to locate the item to be

reordered. When located, touch the item which will

then be highlighted blue (see Figure 8, p. 15).

3. Use the arrow buttons to move the highlighted item to

the top of the list (number 1 position).

4. Touch Save.You will be returned to the Custom Report

screen, where the reordering changes now appear.

Note: On theTD-5 display, report items are ordered from

left to right with the first item appearing at the top

left portion of the screen. Up to nine items can

appear on each Custom Report screen.

The model in Figure 9, p. 15 depicts a custom report

screen with the first nine items displayed on the screen.

Use this model to accurately reorder items in your custom

reports.

Figure 8. Editing a custom report

Scroll buttons

to navigate

through the

data list

Buttons that

re-order your

custom

report list

Scroll buttons

to navigate

through the

data list

Category

Selector

Figure 9. Custom report (order of items)

Custom Report

123

456

789

Reports

16 RT-SVX49A-EN

About

Touch the About button to view the About screen. View

information about the unit controller and theTD-5 display

to which it is connected.Touch the arrow button to scroll

to the next screen.

Data Area

The following data are displayed on the About screen.

Unit Name. This is the name that was entered.

Figure 10. About screen

Unit Name

ABCDEFGHIJKLMNOPQRSTUVWXYZ12456789

RTRM Software Version

6200-XXXX-YY.ZZ RTVM Software Version

6200-XXXX-YY.ZZ VSM Software Version

6200-XXXX-YY.ZZ

RTOM Software Version

6200-XXXX-YY.ZZ RTAM Software Version

6200-XXXX-YY.ZZ RTEM Software Version

6200-XXXX-YY.ZZ

RTDM Software Version

6200-XXXX-YY.ZZ BAS Interface Software Version

6200-XXXX-YY.ZZ

Display User Interface Software Version

6200-XXXX-YY.zz Display Firmware Version

6200-XXXX-YY.zz Display Boot Code Version

6200-XXXX-YY.zz

Reports

RT-SVX49A-EN 17

System Report

Touch the System Report button to view the System

Report screen.Touch the arrow buttons to move between

screens.

Data Area

The following data can be configured to appear on the

System Report screen. Only configured items will appear.

Figure 11. System report screen

Unit Application

VAV,CV,SZVAV Unit Mode

Heat, Cool, Off, Emergency Heat Setpoint Source

Remote, Local

Supply Fan Output

Energized, De-energized Supply Fan Speed %

XXX % Supply Fan Mode

On, Auto

Occupancy

Occupied, Unoccupied Active Cooling Stages

XActive Heating Stages

X

Active Space Temp

XXX.X F/C Active Space Temp Setpoint

XXX.X F/C Outdoor Air Damper %

XXX % Open

Supply Air Temp

XXX.X F/C Active Supply Air Temp Setpoint

XXX.X F/C System Control Mode

Manual, Auto

Economizing

Enabled, Disabled

Ventilation Type

Fixed/DCV

(*DCV = Demand Control Ventilation)

Variable Compressor Speed %

XXX %

Fresh Air Measurement

Installed, Not Installed Demand Limit

Active/Not Active Heating Type

None, Electric, Gas, Hydronic

Exhaust Fan Status Available Cooling Stages

XAvailable Heating Stages

X

Supply Fan Starts

XXXXX Supply Fan Running Time

HHHHH:MM Space Pressure

X.XX in(H2O)/ mm(H20)

Supply Air Pressure

X.XX in(H2O)/ mm(H20) Local Space Temp

X XX.X OF/C Emergency Stop Input

RTOM Low Fan Speed Output Alarm Indicator Output VAV Box Output

Thermostat Y1 Input Thermostat W1/O Input Thermostat G Input

Thermostat W2 Input Thermostat Y2 Input Thermostat X2 Input

Supply Fan Proving Input Condensate Drain Overflow Input Frostat™ Input

Clogged Filter Input Smoke Detector Input Reheat Humidistat Input

Changeover Switch Input

Reports

18 RT-SVX49A-EN

Economizer/Ventilation Report

Touch the Economizer/Ventilation Report button to view

the Economizer/Ventilation Report screen.Touch the arrow

buttons to move between screens.

Data Area

The following data can be configured to appear on the

Economizer/Ventilation Report screen. Only configured

items will appear.

Compressor Report

Touch the Compressor Report button to view the

Compressor Report screen.Touch the arrow buttons to

move between screens.

Data Area

The following data can be configured to appear on the

Compressor Report screen. Only configured items will

appear.

Outdoor Air Damper %

XXX % Open Economizing

Enabled, Disabled Mixed Air Temp

XXX.X F/C

Ventilation Type Economizing Enable Type

Dry Bulb, Reference Enthalpy, Comparative

Enthalpy

Outdoor Air Temp

XXX.X F/C

Active Min OA Damper Position Target

XXX % Manual Enthalpy Override

Enabled, Disabled Return Air Temp

XXX.X F/C

Active Upper CO2 Limit Setpoint

XXXX PPM Active Lower CO2 Limit Setpoint

XXXX PPM Space CO2

XXXX PPM

Active Enthalpy Setpoint

XXXXX BTU / LBM Return Air Humidity

XXX % Outdoor Air Humidity

XXX %

Outdoor Air Flow

XXXXX CFM / LPM Min Outdoor Air Flow Target

XXXXX CFM / LPM Min Outdoor Air Flow Deadband

XXXXX CFM / LPM

Design Min Position High Speed Setpoint

XXX % Design Min Position Mid Speed Setpoint

XXX % Design Min Position Low Speed Setpoint

XXX %

DCV Min Position High Speed Setpoint

XXX % DCV Min Position Low Speed Setpoint

XXX % Power Exhaust Fan Output

Off, On, Auto

DCV Min OA Flow Setpoint

XXXXX CFM / LPM Outdoor Air Flow Adjustment Setpoint Exhaust Fan Starts

XXXXX

Exhaust Fan Running Time

HHHHH:MM Exhaust Damper Position % Open

XXX % Space Pressure

XX.XX IWC /cmWC

Active Space Pressure Setpoint

XX.XX IWC /cmWC Space Pressure Deadband

XX.XX IWC /cmWC Outdoor Fan A Output

Outdoor Fan B Output Variable Speed Outdoor Fan % Ventilation Override Pressurize Input

Ventilation Override Purge Input Ventilation Override Exhaust Input Power Exhaust Fan Output

Supply Fan Proving Input

Table 4. Compressor report - data area

Active Cooling Stages

XAvailable Cooling Stages

XNumber of Compressors Installed

X

Outdoor Fan A Output

Energized, De-energized Outdoor Fan B Output

Energized, De-energized Variable Speed Outdoor Fan %

XXX.X %

Dehumidification Status

Inactive, Active Reheat, Active Enhanced Reheat Entering Evap Temp

XXX.X F/C Variable Compressor Speed %

XXX.X %

Compressor 1 Disable Input

Enabled, Disabled Compressor 2 Disable Input

Enabled, Disabled Compressor 3 Disable Input

Enabled, Disabled

Compressor 1 Proving Input

Open, Closed Compressor 2 Proving Input

Open, Closed Compressor 3 Proving Input

Open, Closed

Heatsink Refrigerant Temperature

XXX.X F/C Supply Air Temp

XXX.X F/C Space Temp

XXX.X F/C

Active Space Cooling Setpoint

XXX.X F/C Defrost Status Ckt 1

Inactive, Defrosting Defrost Status Ckt 2

Inactive, Defrosting

Active Supply Air Temp Cooling Setpoint

XXX.X F/C Switchover Valve (SOV) 1 Output

Heating, Cooling Switchover Valve (SOV) 2 Output

Heating, Cooling

Outdoor Coil Temp Ckt 1

XXX.X F/C Outdoor Coil Temp Ckt 2

XXX.X F/C Compressor 1 Starts

XXXXX

Reports

RT-SVX49A-EN 19

Heating Report

Touch the Heating Report button to view the Heating

Report screen.Touch the arrow buttons to move between

screens.

Data Area

The following data can be configured to appear on the

Heating Report screen. Only configured items will appear.

Configuration Report

Touch the Configuration Report button to view the

Configuration Report screen.Touch the arrow buttons to

move between screens.

Data Area

The following data can be configured to appear on the

Configuration Report screen. Only configured items will

appear.

Compressor 2 Starts

XXXXX Compressor 3 Starts

XXXXX Compressor 1 Running Time

HHHHH:MM

Compressor 2 Running Time

HHHHH:MM Compressor 3 Running Time

HHHHH:MM Number of Compressors Installed

Variable Speed Compressor Reheat Pumpout Relay Defrost Starts Ckt 1

XXXXX

*Phase 2

Table 4. Compressor report - data area (continued)

Table 5. Heating report - data area

Heating Type

None, Electric, Gas, Hydronic Heating Configuration

Staged /Modulating Available Heating Stages

X

Active Heating Stages

XSpace Temp

XXX.X F/C Modulating Heat Output %

XXX %

Gas Heating Status Supply Air Temp

XXX.X F/C Defrost Status Ckt 1

Inactive, Defrosting

Defrost Status Ckt 2

Inactive, Defrosting Active Space Heating Setpoint

XXX.X F/C Outdoor Coil Temp Ckt 1

XXX.X F/C

Outdoor Coil Temp Ckt 2

XXX.X F/C Active Supply Air Temp Heating Setpoint

XXX.X F/C Heating Stage 1 Output

Active, Inactive

Heating Stage 2 Output

Active, Inactive Freezestat Input

Open, Closed Outdoor Air Temp

XXX.X F/C

Gas Heating Type IGN Pressure Switch Input

IGN Temp Limit Input IGN Flame Rollout Input IGN Inducer High Output

IGN Inducer Low Output

Table 6. Configuration report - data area

Unit Application

CV, VAV, SZVAV Refrigeration Type

Cooling Only, Heat Pump

Product Type

Voyager™ Commercial, Precedent™/

Precedent™ 17 Plus/Voyager™ Light

Commercial/Odyssey™

Dehumidification

None, Hot Gas Reheat, Enhanced Supply Fan Control Type

Fixed, Variable, IGV Economizer

Installed, Not Installed

Dehumidification Type

Staged, Modulating Heating Type

None, Electric, Gas, Hydronic CV Control Type

Zone Sensor, Thermostat

Cooling Stages Configured

XCooling Steps Input

3 Step, 2 Step Number of Compressors Installed

X

Heating Stages Configured

XVariable Speed Compressor

Installed, Not Installed

Economizer Enable Type

Drybulb, Reference Enthalpy, Comparative

Enthalpy

Supply Fan Motor Type

Fixed, VFD, ECM, ERM Supply Fan Motor Control

0 to 10VDC, PWM

Heat Pump Type

Single, Independent Windmill Prevention

Enable, Disable Gas Ignition Module 1

Staged, Modulating

True Supply Air Reporting

Enable, Disable Supply Air Tempering Input

Enable, Disable Gas Ignition Module 2

Installed, Not Installed

Reports

20 RT-SVX49A-EN

Sensor Report

Touch the Sensor Report button to view the Sensor Report

screen.Touch the arrow buttons to move between screens.

Data Area

The following data can be configured to appear on the

Sensor Report screen. Only configured items will appear.

Binary Input Report

The Binary Input report provides general Reliatel Unit

operating information.Touch the Binary Input Report

button to view the Binary Input Report screen.

Data Area

The following data can be configured to appear on the

Configuration Report screen. Only configured items will

appear.

Manual Enthalpy Override

Enable, Disable Lead Lag Configuration Input

Enable, Disable OA Flow Compensation

Enable, Disable

Outdoor Fan Cycling Input

Normal, Lower Programmable Zone Sensor

Installed, Not Installed Cabinet Type

Horizontal, Downflow

Outdoor Air Flow Compensation

Enable, Disable Evaporator Defrost Control

Enable, Disable RTRM Fan Proving Input

Closed, Open

Supply Air Tempering Input

Disable, Enable Outdoor Fan Cycling Input

Normal, Lower Exhaust Air Control - StatiTrac™

Installed, Not Installed

Table 6. Configuration report - data area (continued)

Table 7. Sensor report - data area

Active Space Temp

XXX.X OF/C Local Space Temp

XXX.X OF/C Supply Air Temp

XXX.X OF/C

Outdoor Air Temp

XXX.X OF/C Mixed Air Temp

XXX.X OF/C Return Air Temp

XXX.X OF/C

Outdoor Air Humidity

XXX.X% Return Air Humidity

XXX.X% Space CO2

XXXX PPM

Outdoor Air Flow

XXXXX CFM/LPM Space Humidity

XXX% Outdoor Coil Temp Ckt 1

XXX.X OF/C

Outdoor Coil Temp Ckt 2

XXX.X OF/C Space Pressure

X.XX in(H2O)/mm(H20) Reheat Entering Evap Temp

XXX.X OF/C

Supply Air Pressure

X.XX in(H2O)/ mm(H20)

Table 8. Binary input report - data area

RTRM Emergency Stop Input

Auto, Emergency Stop Occupancy RTRM Fan Proving Input

Closed, Open

Thermostat Y1 Input

Open, Closed Thermostat W1/O Input

Open, Closed Thermostat G Input

Open, Closed

Thermostat W2 Input

Open, Closed Thermostat Y2 Input

Open, Closed Thermostat X2 Input

Open, Closed

Compressor 1 Disable Input

Closed, Open Compressor 1 Proving Input

Operating, Not Operating Compressor 2 Disable Input

Closed, Open

Compressor 2 Proving Input

Operating, Not Operating

RTOM Supply Fan Proving Input

Open, Closed Condensate Drain Overflow Input

Open, Closed Ventilation Override Pressurize Input

Open, Closed

Ventilation Override Purge Input

Open, Closed Ventilation Override Exhaust Input

Open, Closed Frostat™ Input

Open, Closed

Clogged Filter Input

Open, Closed Freezestat Input

Open, Closed Smoke Detector Input

Open, Closed

Reheat Humidistat Input

Open, Closed Changeover Switch Input

Cooling, Heating

VSM Compressor 3 Disable Input

Closed, Open Compressor 3 Proving Input

Operating, Not Operating

RTVM Exhaust Fan Proving Input

Open, Closed

Reports

RT-SVX49A-EN 21

Binary Output Report

The Binary Input report provides general Reliatel Unit

operating information.Touch the Binary Input Report

button to view the Binary Input Report screen.

Data Area

The following data can be configured to appear on the

Configuration Report screen. Only configured items will

appear.

Note: Operating Modes:The operating Mode page shall

show the user the general operation of the unit, and

what modes it is operating in.

IGN IGN Pressure Switch Input

Open, Closed IGN Temp Limit Input

Open, Closed IGN Flame Rollout Input

Open, Closed

Table 8. Binary input report - data area (continued)

Table 9. Binary output report - data area

RTRM Supply Fan Output

Off, On Compressor 1 Output

Off, On Compressor 2 Output

Off, On

Heat Stage 1 Output

Off, On SOV 1 Output

Off, On Outdoor Fan A Output

Off, On

Heat Stage 2 Output

Off, On

SOV 2 Output

Off, On

or

Low Fan Speed

or

Compressor 3 Output

Off, On

Outdoor Fan B Output

Off, On

RTOM/RTAM/RTVM/

RTEM/RTDM RTOM Low Fan Speed Output

Off, On Alarm Indicator Output

Off, On VAV Box Output

Off, On

Power Exhaust Fan Output

Off, On Reheat Pumpout Relay

Off, On

IGN IGN Inducer High Output

Off, On IGN Inducer Low Output

Off, On

Figure 12. Operating modes report details screen

22 RT-SVX49A-EN

Graphs

Graphs allow users to view data in graphical format on the

Display. Four custom graphs and eight standard graphs

are available. Graphs can be created with a maximum of

four lines per graph. Custom graphs are user-defined and

can be edited by changing the scale on the left and rightY-

axis and choosing the line color.

Touch the Graphs button in the bottom display area to view

the Graphs screen (Figure 13, p. 22).The Graphs screen

contains twelve buttons that allow you to view and edit a

particular graph.There are four custom graphs and 8

standard graphs.

Creating a Custom Graph

5. Navigate to the Graphs screen, then touch an available

data graph button.

The Custom Graph screen appears.

6. Touch the Edit Graph button.

The Edit Graph screen appears (Figure 14, p. 22).

Figure 13. Graphs screen

Figure 14. Edit graph screen

Graphs

RT-SVX49A-EN 23

7. Touch the Add/Remove button to add values to the

custom data graph.

The Add/Remove screen appears.

8. Use the arrow buttons to select a value.

9. Select the values, then touch theAdd button (up to four

selections are allowed).

10. Touch the Save button.The Edit Graph screen appears,

which reflects the selected values.

11. Use the Edit Graph screen to modify the graph.Touch

the Edit button that corresponds with the value that

you want to change. Only one value can be edited at a

time.

12. From the Edit screen you can choose whichY-axis to

display the value, a color, and whether or not to show

data samples.Touch the Save button when finished.

Repeat the process with remaining values.

Figure 15. Adding data logs to the custom graph

Figure 16. Edit graph screen (after values have been added)

Graphs

24 RT-SVX49A-EN

13.Touch the Save button to display the new graph

(Figure 18, p. 24).

Note: Depending on the sampling rate, the custom graph

may be empty for several hours.

You can make changes to the way data is presented on the

graph at anytime.Touch the zoom-in icon and zoom-

out icon to either increase or decrease the viewable

time frame.This action also enables back and forward

arrows that allow you to view data at various times of the

day.

Editing the Y-Axis

The default values on the right and leftY-axes can be

changed according to your specifications.

14. Touch the EditY-Axis button located on the top portion

of the Custom Data Graph screen.

The EditY-Axis screen appears (Figure 19, p. 25).

Figure 17. Customizing the graph

Figure 18. Viewing the graph

Graphs

RT-SVX49A-EN 25

15.Touch the Manually Select Range box for either the left

or rightY-axis.

16.Touch the edit button next to one of the two value

ranges.

The Keypad screen appears.

17. Select a new value and then touch Enter to save.

18. Repeat steps 2 through 4 until all preferred changes

have been made.

Standard Graphs

There shall be 8 standard graphs.The standard graphs are

below:

Space Temperature:

The table below describes the data in the System Status

graph:

Compressor Graph:

The table below describes the data in the graph:

Figure 19. Editing theY-Axis

Table 10. Standard graphs

Space Temperature Economizer

Compressor Outside Air Ventilation

VAV Humidity

Heat Pump CO2

Data Point Line Color Axis

Active Space Temp Setpoint Blue Left

Active Space Temp Green Left

Supply Air Temp Black Left

Return Air Temperature Red Left

Data Point Line Color Axis

Active Supply Air Temp Setpoint Pink Left

Variable Compressor Speed % Green Left

Supply Air Temp Black Left

Active Cooling Stages Blue Right

Graphs

26 RT-SVX49A-EN

VAV System:

The table below describes the data in the System Status

graph:

Economizer Graph:

The table below describes the data in the graph:

Outside Air Ventilation:

The table below describes the data in the graph:

CO2Graph:

The table below describes the data in the graph:

Humidity Graph:

The table below describes the data in the graph:

Heat Pump Graph:

The table below describes the data in the graph:

Data Point Line Color Axis

Active Supply Air Temp Setpoint Pink Left

Active Space Temp Green Left

Supply Air Temp Black Left

Return Air Temp Red Left

Data Point Line Color Axis

Outdoor Air Temp Purple Left

Mixed Air Temp Grey Left

Active Min OA Damper Position Target Pink Right

Outdoor Air Damper % Yellow Right

Data Point Line Color Axis

Min Outdoor Air Flow Target Black Left

Outdoor Air Flow Pink Left

Outdoor Air Damper % Yellow Right

Outdoor Air Temp Purple Right

Data Point Line Color Axis

Active Upper CO2 Limit Setpoint Red Left

Active Lower CO2 Limit Setpoint Black Left

Space CO2Green Left

Outdoor Air Damper % Yellow Right

Data Point Line Color Axis

Space Dehumidification Setpoint Yellow Left

Outdoor Air Humidity Red Left

Return Air Humidity Black Left

Space Humidity Green Left

Data Point Line Color Axis

Outdoor Coil Temp Ckt 1 Green Left

Outdoor Coil Temp Ckt 2 Blue Left

Outdoor Air Temp Purple Left

Discharge Air Temperature Grey Left

RT-SVX49A-EN 27

Settings

The Settings screen provides options for display settings,

language, overrides and security.Touch the Settings

button in the bottom display area to view the Settings

screen.

Three categories for settings appear on the screen:

• Control Settings

• Display Settings

• Security Settings

Setpoints

Touch the Setpoints button to view the Setpoints screen.

Touch the arrow buttons to move between screens.

Figure 20. Settings screen

Figure 21. Setpoints screen

Settings

28 RT-SVX49A-EN

Data Area

The following data can be configured to appear on the

Setpoints screen. Only configured items will appear.

Setup

Touch the Setup button to view the Setpoints screen.

Touch the arrow buttons to move between screens.

This Setup screen shows a list of the setup items in button

format.The available setup items are listed below:

Occupied Space Cooling Setpoint Unoccupied Space Cooling Setpoint Space Dehumidification Setpoint

Occupied Space Heating Setpoint Unoccupied Space Heating Setpoint Supply Air Reheat Setpoint

Discharge Air Heating Setpoint Discharge Air Cooling Setpoint Duct Static Pressure Setpoint

Duct Static Pressure Deadband Morning Warm-up Setpoint Supply Air Cooling Setpoint

Supply Air Heating Setpoint Daytime Warm-up Initiate Setpoint Space Pressure Setpoint

Space Pressure Deadband Daytime Warm-up Terminate Setpoint CO2 Upper Limit Setpoint

CO2 Lower Limit Setpoint Enthalpy Setpoint Supply Air Reset Setpoint

Exhaust Fan Enable Setpoint Supply Fan Adjustment Setpoint Outdoor Air Flow Adjustment Setpoint

Design Min OA flow Setpoint DCV Min OA Flow Setpoint Min OA Flow Deadband

Design Min OA Damper Pos Setpoint 100% Fan Design Min OA Damper Pos Setpoint Mid Fan Design Min OA Damper Pos Setpoint Min Fan

DCV Min OA Damper Pos Setpoint 100% Fan DCV Min OA Damper Pos Setpoint Min Fan Outdoor Air Flow Adjustment Setpoint

Figure 22. Setup screen

Unit Mode

Heat, Cool, Auto Supply Fan Mode

On, Auto Emergency Heat Mode Request

Auto, Emergency Heat

System Control Mode

Local, Remote Display Read Only Mode

Read, Write

Supply Air Reset Type

Heat, Cool, Auto

Service Test

Disable, IGV Close, IGV Open,

Fan Only/Min Vent,

Economizer Open, Cool 1, Cool 2, Cool 3,

Dehumid/Reheat, Heat 1, Heat 2, Heat 3,

Defrost, Emergency Heat

Settings

RT-SVX49A-EN 29

Display Settings Screen

The selections in this category contain settings that affect

the way in which information is displayed on all of theTD-

5 display screens. From each screen, the current settings

can be viewed.To change a setting, touch the preferred

value.

Display Preferences

Touch the Display Preferences button to open the

associated screen (Figure 23, p. 29). On this screen, all

available options to display information on theTD-5

screens are available.There are two pages on this screen,

accessed by using the arrow button at the bottom of the

screen.

Date Format

Touch the Date Format button to open the associated

screen.Three options are available to display the current

date: MMDDYYYY, DDMMYYYY, and YYYYMMDD.

Date Separator

Touch the Date Separator button to open the associated

screen.Three options are available to display separators

in the date format: None, Hyphen (-), or Slash (/).

Time Format

Touch the Time Format button to open the associated

screen.Two options are available: 12-Hour format and 24-

Hour format (also referred to as “military time”).

Unit System

Touch the Unit System button to open the associated

screen.Two options are available: SI (system

international) or IP (Inch-Pound).

Brightness

Touch the Brightness button, or the brightness icon

( )located at the bottom left of each screen, to open the

associated screen. Screen brightness is measured in

percentage. Use the keypad to enter a new brightness

number.

Backlight Time-out

Touch the Backlight Time-out button to open the

associated screen.This value is measured in minutes, with

30 being the maximum limit. Use the keypad to enter a

backlight time-out value.This value is the amount of time

that the display will remain lit without activity. When the

backlight times out, users will be automatically logged off

due to inactivity.

Header Data Point

Use the arrow button on the Display Preferences screen to

advance to page 2.Touch the Header Data Point button to

open the associated screen.The Header Data Point

appears in the top right display area on all screens. Use the

arrow buttons to scroll through the points. Click Add to

move the highlighted point to the right side of the

screen(Figure 24, p. 30). Click Save.

Figure 23. Display preferences screen

Settings

30 RT-SVX49A-EN

Collection Frequency

Collection frequency sets the time interval that the Graph

Data is saved, and displayed on the graph.The faster the

sample rate, the lower the duration.The default of 30

seconds shall provide 3.5 days of data collection.

Figure 24. Setting the header data point

Header data

point

Figure 25. Collection frequency

Settings

RT-SVX49A-EN 31

Home Page

Use the arrow button on the Display Preferences screen to

advance to page 2.Touch the Home Page button to open

the associated screen.This function allows you to choose

what will display when the home button is touched.

Language

Touch the Language button, or the language icon ( )

located at the bottom right of each screen, to open the

open the Language screen.Twenty-six languages are

available and represented on the selection buttons. Select

a language that you want displayed on eachTD-5 screen

and then touch Save.See“Language,” p. 31.

Date and Time

Touch the Date andTime button to open the associated

screen.To enter a new date or time, touch the digit you

want to change. When enabled for editing, the digit will

appeared with a black border. when finished, touch Apply

or Save.Or,

Figure 26. Home page screen

Figure 27. Language screen

Settings

32 RT-SVX49A-EN

tap the digit twice which opens the keypad screen where

you can make date and time entries. When finished, touch

Enter; you will be returned to the Date andTime screen.

Touch Apply or Save.

Clean Touchscreen

Touch the CleanTouchscreen button to safely clean theTD-

5 touchscreen using any brand of common household

glass cleaner. When this button is touched, the screen

background color becomes black, allowing dirt and

fingerprints to become more visible. It also displays a

countdown timer (five to zero seconds).Touch the screen

anytime within the 5-second countdown to begin cleaning

the screen (each touch resets the 5-second countdown).

Figure 28. Date and time screen

RT-SVX49A-EN 33

Troubleshooting

This section describes the possible error messages and

other issues that you may encounter while using the

Tracer™TD-5 display.

Important: There are no serviceable parts within the

TD-5 display enclosure. Opening the

enclosure will void the product warranty.

Identifying and Diagnosing Issues

Problem Possible Cause Possible Solution

Blank display (TD-5 does not respond

to touch). No power. Verify that the TD-5 is connected to a power source,

and that the power source is in working condition.

After powering up, the TD-5 displays

a message that it is not

communicating. Controller not powered up. Replace cable if necessary. Power up the controller if

necessary.

No data available in custom report. Data has not yet been defined for the report. Add data to report. See “Creating a custom report,”

p. 14.

The manufacturer optimizes the performance of homes and buildings around the world. A business of Ingersoll Rand,

the leader in creating and sustaining safe, comfortable and energy efficient environments,the manufacturer offers a

broad portfolio of advanced controls and HVAC systems, comprehensive building services, and parts. For more

information, visit www.IRCO.com.

The manufacturer has a policy of continuous product and product data improvement and reserves the right to change design and specifications without notice.

We are committed to using environmentally

conscious print practices that reduce waste.

© 2013Trane All rights reserved

RT-SVX49A-EN 04 Nov 2013

(NEW)