TransCore 05752 LOW POWER RFID TRANSPONDER TRANSMITTER User Manual 16 xxxx xx Waterproof Install Instruct

Download:
Mirror Download [FCC.gov]
Document ID	2016445
Application ID	2G/rm+GZE7Zg9zx/h3BSHg==
Document Description	User Manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	13.78kB (172216 bits)
Date Submitted	2013-07-15 00:00:00
Date Available	2013-08-29 00:00:00
Creation Date	2003-04-07 13:23:32
Producing Software	Acrobat Distiller 10.1.7 (Windows)
Document Lastmod	2013-06-03 09:59:48
Document Title	16-xxxx-xx Waterproof Install Instruct.fm
Document Creator	FrameMaker 10.0.2
Document Author:	pstiles

Installation Instructions
for eZGo AnywhereTM Waterproof On-Board Units
16-xxx-xx 05/31/13
General Installation Information
Metallized Windshields: Some vehicle windshields contain a metallic treatment that could prevent an interior
windshield-mounted on-board unit (OBU) from working correctly. If you have a vehicle with a metallized
windshield, you may need to install an exterior OBU on your vehicle instead of the interior windshield-mounted
OBU. Contact your local OBU customer service center for more information. If your vehicle’s metallized
windshield has a metal-free zone, it is usually located near the rearview mirror.
Metal-Free Zone: Some vehicle metallized windshields have a metal-free zone. If your windshield has this zone,
center the OBU in that area and follow the installation instructions listed on this page.
ar
Tinted Windshields: Some vehicles have a metallic tint across the top of the windshield that might interfere with
reading the OBU. If your windshield has this metallic tint, install the OBU at least 2 inches (5.1 cm) below the
tinted area. Nonmetallic tint does not affect OBU performance.
Required Supplies
Waterproof OBU
Commercial glass cleaner and paper towels
lim
•
•
in
Metal Sun Visors: Some vehicles have an exterior-mounted sun visor that might interfere with reading the OBU. If
your vehicle has this visor, mount the OBU at least 2 inches (5.1 cm) below the visor.
OBU Installation and Removal Procedures
re
The OBU may be equipped with hook-and-loop strips or double-sided tape.
To install the OBU
1. Choose the location for your OBU (Figure 1).The OBU should be mounted approximately 1 inch (2.54 cm)
below the rearview mirror post.
Figure 1. Optimum Locations for OBU Performance
2.
Clean and dry the interior windshield surface completely before affixing the fastener strips. The windshield
temperature must be at least 68ºF (20ºC) for optimum bonding.
3.
Peel off the double-faced barrier on the hook-and-loop strips or double-sided
S P Etape
C I(Figure
F I C2).
A T I O N S
ar
Note: When installing the OBU for the first time, leave the OBU in place for at least 24 hours to allow the
adhesive to cure.
Figure 2 Remove Backing to Expose Adhesive
Holding the OBU so that the arrows on the front label point up as shown in Figure 3, press the OBU against
the windshield and hold for 10 seconds.
re
lim
in
4.
Figure 3 Correct Tag Orientation
To remove an OBU from the windshield, grip the OBU at the top and bottom sides. Gently lift the OBU
away from the windshield on one end until the OBU is free from the windshield. Be careful not to hit the
rearview mirror.
5.
NO UNAUTHORIZED MODIFICATIONS STATEMENT
Caution: This equipment may not be modified, altered, or changed in any way without permission from TransCore, LP. Unauthorized modification may void the equipment
authorization from the FCC and will void the TransCore warranty.
RADIO FREQUENCY INTERFERENCE STATEMENTS
Note: This device complies with Part 15 of the FCC Rules and the Industry Canada Licence-Exempt RSS Standards. Operation is subject to the following two conditions: (1)
this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of this device.
Note: Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareils radio exempts de licence. L’exploitation est autorisée aux deux conditions
suivantes: (1) l’appareil ne doit pas produire de brouillage, et (2) l’utilisateur del’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est
susceptible d’en compromettre le fonctionnement.
www.transcore.com
©2012. TransCore, LP. All rights reserved. TRANSCORE and EGO are registered trademarks and EZGO ANYWHERE is a trademark, and are used under license.
All other trademarks are the property of their respective owners. Contents are subject to change. Printed in the U.S.A.
16-xxx-xx 05/31/13

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.6
Linearized                      : Yes
Author                          : pstiles
Create Date                     : 2003:04:07 13:23:32Z
Modify Date                     : 2013:06:03 09:59:48-06:00
Has XFA                         : No
Language                        : en
XMP Toolkit                     : Adobe XMP Core 5.2-c001 63.139439, 2010/09/27-13:37:26
Producer                        : Acrobat Distiller 10.1.7 (Windows)
Creator Tool                    : FrameMaker 10.0.2
Metadata Date                   : 2013:06:03 09:59:48-06:00
Format                          : application/pdf
Title                           : 16-xxxx-xx Waterproof Install Instruct.fm
Creator                         : pstiles
Document ID                     : uuid:4ada2e88-0b30-48ff-b1e5-5e74233f5eca
Instance ID                     : uuid:a6e0d8c7-698b-45a1-b3b8-3c5f6d4cb00c
Page Mode                       : UseNone
Page Count                      : 2

EXIF Metadata provided by EXIF.tools