Transact Campus PR5000X011 Point of Sale Reader User Manual PR5000 HW Install Guide

Blackboard Inc. Point of Sale Reader PR5000 HW Install Guide

User Manual

403-002-018 Rev APoint of Sale Reader (PR5000)Hardware Installation Guide
403-002-018 Rev ATable 0-1: Revision HistoryBb Document Part Number Rev. Description Date403-002-018 AECO10431. Initial Release. PENDING
403-002-018 Rev AFederal Communications Commission (FCC) statementThis device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:1. This device may not cause harmful interference.2. This device must accept any interference received, including interference that may cause undesired operation.Note: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy, and if it is not installed and used in accordance with the instruction manual, it may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference, in which case the user will be required to correct the interference at his own expense.Modifications: Any modifications made to this device that are not approved by Blackboard Inc. may void the authority granted to the user by the FCC to operate this equipment.IMPORTANT NOTE: This equipment complies with the FCC radiation exposure limits set forth for an uncontrolled environment. End users must follow the specific operating instructions for satisfying RF exposure compliance. The antenna(s) used for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons and must not be co-located or operating in conjunction with any other antenna or transmitter.Contains: FCC ID: VPYLB1DX Murata WLAN + Bluetooth Combo Module (LBEE5KL1DX-883)FCC ID: WAP2005 Cypress Semiconductor Bluetooth Low-Energy Module (CYBLE-222014-01)
403-002-018 Rev AIndustry Canada Class A emission compliance statementThis Class A digital apparatus complies with Canadian ICES-003.Cet appareil numérique de la classe A est conforme à la norme NMB-003 du Canada.This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device.Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorisée aux deux conditions suivantes : (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement.Contains:Contient des IC: 772C-LB1DX and 7922A-2005 Australia and New Zealand Class A statementAttention: This is a Class A product. In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures.Radiation Exposure StatementThis equipment complies with radiation exposure limits set forth for uncontrolled environment. The antenna(s) used for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons and must not be collocated or operating in conjunction with any other antenna or transmitter.Déclaration d'exposition aux radiationsCet appareil se conforme aux limites d'exposition aux rayonnements pour un environnement non contrôlé. L'antenne (s) qui est utilisé pour cet émetteur doit être installé pour produire une distance de séparation d'au moins 20 cm de toutes personnes et ne doit pas être installé à proximité ou utilisé en conjonction avec une autre antenne ou émetteur.IC: 772C-LB1DX Murata WLAN + Bluetooth Combo Module (LBEE5KL1DX-883)IC: 7922A-2005 Cypress Semiconductor Bluetooth Low-Energy Module (CYBLE-222014-01)
403-002-018 Rev ANote: The regulatory compliance information above can be viewed on the reader’s display. To view this information on the reader, at the Main Menu, press the Regulatory Information button.
Contents403-002-018 Rev A I1 BLACKBOARD POINT OF SALE READER (PR5000) HARDWARE INSTALLATION GUIDE1 Overview1Features:2 PR5000 Functional Overview2 Inputs and Outputs:2 Functional Overview - Bottom3 Functional Overview - Top4 PR5000 Mount Kit5 INSTALLING THE PR5000 READER5 Reader Installation Overview and Wiring Considerations5 Wiring and Power Considerations:6 Tabletop Installation6 Install the reader on a tabletop7 Wall Mount Installation8 Installing the Mount Kit10 Connecting Cables11 Technical Specifications
OVERVIEW 1-1403-002-018 Rev ABLACKBOARD POINT OF SALE READER (PR5000) HARDWARE INSTALLATION GUIDEOVERVIEWThe Blackboard Point of Sale (POS) Reader PR5000 is an Android-based reader. When configured, the PR5000 communicates with the Blackboard Transaction System (BbTS), and incorporates both contactless and magnetic stripe reader capabilities. The reader can be set up as either an attended or unattended device.Features:• Bluetooth Classic and BLE compatible.• Large LCD capacitive touchscreen.• Adjustable screen backlight.• Manual screen rotation (180°).• Wireless communication to the host.• A real time clock.• LEDs at the bottom of the unit for illumination. LED options:• a - Device Idle• b - Valid Transaction• c - Invalid Transaction The LED options are configurable. When enabled, the color and brightness are adjustable.• Discernible tones for valid and invalid transactions.• Stereo speakers (2).• The PR5000 supports: Sony Felica, MIFARE Classic, MIFARE DESFire EV1 & EV2, and Blackboard Mobile Credentials (Android only).The following is the list of features that are included, but will not be operational for the first phase. Look for future releases that enable these features.• Ambient Light Sensor - The display dims and brightens based on ambient light in the device location.• Camera - Captures an image with each transaction. This enables the ability to view an image with a transaction for situations such as investigating fraud claims, to determine cause of damage to the device, etc.• Microphone - This is an ADA feature. Use this feature to call for assistance when encountering issues during a transaction or to have any questions answered.• Proximity Sensor - Motion wakes up the device to either display the beginning transaction screen (varies based on device software running) or play video/images from the Media Server.Figure 1-1 PR5000 Reader
PR5000 FUNCTIONAL OVERVIEW 1-2403-002-018 Rev APR5000 FUNCTIONAL OVERVIEWInputs and Outputs:• One RJ-45 connector that is utilized for Power over Ethernet standard 802.3af at 15.40 W.• Two USB 2.0 Type A connectors.• One USB Type C connector that support USB 2.0 high speed data transfer.• 12V - 15W DC Power Input • Two 2W stereo speakersFunctional Overview - BottomFigure 1-2 Functional Overview - BottomBottom of the PR5000 ReaderLEDs (4)Stereo Speakers (2)USB 2.0 Type AUSB Type CMicro SD CardConnectorDC Power InputRJ-45ResetButton
PR5000 FUNCTIONAL OVERVIEW 1-3403-002-018 Rev AFunctional Overview - TopFigure 1-3 Functional Overview - TopLCD CaptiveTouchscreenProximity andAmbient Light SensorMicrophoneCameraMagneticCard ReaderMicrophone
PR5000 MOUNT KIT 1-4403-002-018 Rev APR5000 MOUNT KITA mount kit is provided to aid in mounting the reader to a wall. Open the packaging, and then verify that all parts are included. If there are any discrepancies, contact your Blackboard Client Manager.Figure 1-4 PR5000 Mount KitTable 1-1: List of partsITEM NO. PART NUMBER DESCRIPTION QTY.1 044-028-C34 M4 X 6MM PANHEAD MACHINE SCREW, ZINC PLATED 52 044-028-E39 6-32 X 3/4 TRUSS HEAD PHILLIPS MACHINE SCREW 53 044-028-E40 6-32 X 1_4 SS FLAT HEAD PHILLIPS MACHINE SCREW 54 044-042-041 RJ45 CAT5e 10' PATCH CABLE, BLACK 15 044-046-E03 6-32 X 1/2 TAMPER PROOF SCREW 56 044-051-000 12V, 30W INERNATIONAL POWER SUPPLY, ENERGYSTAR LEV5 17 044-059-119 PR5000 MOUNT BASE 18 044-059-120 PR5000 MOUNT 1PR5000 Mount PR5000 Mount Base
READER INSTALLATION OVERVIEW AND WIRING CONSIDERATIONS 1-5403-002-018 Rev AINSTALLING THE PR5000 READERThe Blackboard PR5000 Reader can be placed on a tabletop or secured to a wall.This section includes the following:•Reader Installation Overview and Wiring Considerations (page 1-5)•Tabletop Installation (page 1-6)•Wall Mount Installation (page 1-7)READER INSTALLATION OVERVIEW AND WIRING CONSIDERATIONSWiring and Power Considerations:• Wall Wart power supply. (included)• The power supply requires a dedicated outlet.• Power Over Ethernet. (POE)• POE provides power through the network cable, and reduces cable clutter.• When providing POE, the maximum LAN cable length must not exceed 100 meters (328 Feet).• Both the POE switch and PR5000 must be installed within the same building or structure.• A CAT-5 cable must be connected between the POE switch and the port on the PR5000. (RJ-45)Note: For a more details, see: the Blackboard Transact System Implementation Guide.
TABLETOP INSTALLATION 1-6403-002-018 Rev ATABLETOP INSTALLATIONFigure 1-5 PR5000 Tabletop InstallationThe PR5000 Reader can be placed on a tabletop for events such as a fundraiser or a library book sale. This section includes the instructions for installing the PR5000 Reader on a tabletop. Please review the tabletop installation considerations before continuing.Tabletop installation considerations:• Wiring and Power Considerations reviewed.• The location and the height of the reader should be selected to permit easy access.• Ensure that Americans with Disabilities Act (ADA) requirements are met.• In warm climates, the reader should be shaded from direct sunlight.• The maximum external temperature of the reader must not exceed 104°F (40°C) to ensure that the internal temperature limit is not exceeded.• Ensure there is enough clearance for the operator to access the screen and swipe cards.Install the reader on a tabletopTo install the reader on a tabletop1Connect power, network, and communication cables to the reader.See: PR5000 Functional Overview (page 1-2) and Connecting Cables (page 1-10).Note: Connecting power is not required when using the battery option.2Place the reader on the tabletop, and then neatly route all cables underneath the reader and out of the way. Optionally use cable ties to keep all cables together.3Connect the power cord to a grounded outlet or power strip.Tabletop installation is complete. See: the Point of Sale (PR5000) Configuration Guide to complete your set up.
WALL MOUNT INSTALLATION 1-7403-002-018 Rev AWALL MOUNT INSTALLATIONThe PR5000 Reader ships with a mount kit. The kit is optional, but simplifies wall installation. Follow the instructions in this section to properly mount your PR5000 Reader to a wall. Please review the wall mount installation considerations before continuing. The Mount Kit is compatible with Video Electronics Standards Association (VESA) 75 mounts (not included).Note: The PR5000 includes a feature that allows you to rotate the screen 180 degrees. This is helpful when mounting the reader to a wall. See: the Point of Sale (PR5000) Reader Configuration Guide for instructions on how to enable and disable this feature.Figure 1-6 Wall Mount InstallationWall mount installation considerations:• Wiring and Power Considerations reviewed.• An electrical gang box to provide power and a route for communication cables.The reader will be attached to this gang box.Note: The electrical gang box and wiring should be installed by a trained technician.• The location and the height of the reader should be selected to permit easy access.• Ensure that Americans with Disabilities Act (ADA) requirements are met.• In warm climates, the reader should be shaded from direct sunlight.• The maximum external temperature of the reader must not exceed 104°F (40°C) to ensure that the internal temperature limit is not exceeded.• Ensure there is enough clearance for the operator to access the screen and swipe cards.
WALL MOUNT INSTALLATION 1-8403-002-018 Rev AInstalling the Mount KitTo install the Mount Kit1If you haven’t already, open the Mount Kit packaging, and then verify that all parts are included.See: PR5000 Mount Kit (page 1-4) for the list of parts.Note: If there are any discrepancies, contact your Blackboard Client Manager.2Obtain the PR5000 Mount Base (Blackboard Part No. 044-059-119) or VESA 75 mount (not included).When using the PR5000 Mount Base, review Figure 1-7 before continuing.Figure 1-7 PR5000 Mount Base3Attach the Mount Base or VESA 75 mount to the electrical gang box.For the PR5000 Mount Base, use the 6-32 X 3/4 Truss Head Phillips machine screws (4).For a VESA mount, use the M4 X 6mm Panhead machine screws (4).BottomTopFront
WALL MOUNT INSTALLATION 1-9403-002-018 Rev AFigure 1-8 Mount Base Installation4Tighten all screws.5Loosely install 6-32 X 1/2 Tamper Proof screws (2) in the upper screw holes shown in Figure 1-8.The remaining Tamper Proof screws will be installed later.6Obtain the PR5000 Reader and the PR5000 Mount included (Blackboard Part No. 044-059-120).7Place the reader on a tabletop with the front of the reader facing downward.Blackboard recommends using a towel or soft cloth underneath the reader to avoid scratches.8Align the Mount with the reader as shown in Figure 1-9.9Attach the Mount to the reader using the 6-32 X 1/4 SS Flat Head Phillips machine screws (4).Figure 1-9 PR5000 Mount and ReaderLoosely install TamperProof Screws (2) in theupper screw holes.
WALL MOUNT INSTALLATION 1-10403-002-018 Rev AConnecting Cables10 Connect cables to the PR5000. Refer to Figure 1-2.Note: When using the PR5000 Reader as an Authorization Reader, configure the Transaction Terminal Options in TS, see: the Blackboard Transaction System Administration Guide (Hardware chapter). The reader provides data output through AUX1. A serial connection from AUX1 to third-party hardware is required.11 Place the PR5000 Reader on the Mount Base by sliding the Mount’s open slots over the loosely attached screws previously installed.Figure 1-10 Installing the PR5000 to Wall12 Install two more 6-32 X 1/2 Tamper Proof screws into the lower slotted holes.13 Tighten all four Tamper Proof screws.14 Verify that the reader is secure.Wall mount installation is complete. See: the Point of Sale (PR5000) Configuration Guide to complete your setup.
TECHNICAL SPECIFICATIONS 1-11403-002-018 Rev ATECHNICAL SPECIFICATIONSTable 1-2: PR5000 Technical SpecificationsDimensions: 9.0" x 7.5" x 2.3"Weight: 1.55 lbs. (0.70 kg)Input Power: 12 VDC 1.1 Amp. MaximumOperating: Temperature range: 0 to 40 degrees Celsius.Non-Operation: Temperature range: -20 to 70+ degrees Celsius.Regulatory Compliance: US & Canada: FCC Part 15 Class A, CSA/UL 62368-1 Ed 2.0Europe: EN 62368-1 Ed 2.0, CE Mark.Australia/New Zealand: IEC 62368-1 Ed 2.0USB 2.0 Type A Connectors (2): 5 Volts at 1 AUSB Type C Connector: 5 Volts at 1 AEthernet Connection: RJ-45 (POE). 802.3af at 15.40W.Processor: i.MX 6 quad core processorIP - Ingress Protection rating: IP 54Operating system (OS): Android Lollipop 5.1.1Host communication: 10/100 Base-T ethernet (IP) or wireless.Display: 7 inch TFT LCD 1024 x 600 display.

Navigation menu