Transtek Medical Electronics AW8001-LS Bluetooth Module User Manual Rev1

Download:
Mirror Download [FCC.gov]
Document ID	2033138
Application ID	TB6BL2bGwoQHVC5Vbpm1zg==
Document Description	User Manual Rev1
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	52.89kB (661137 bits)
Date Submitted	2013-08-05 00:00:00
Date Available	2013-08-07 00:00:00
Creation Date	2013-07-26 13:02:58
Producing Software	pdfFactory Pro 2.23 (Windows XP Chinese)
Document Lastmod	2013-07-30 13:15:39
Document Title	E:\Kelvin work file\project file\LS产品\TSF1235系列PCB的项目【GBF-1064BT系列】\AW8001模块\AW8001 datasheet.doc
Document Creator	pdfFactory Pro www.fineprint.com.cn
Document Author:	09010

Guangdong Transtek Medical Electronics Co.,Ltd
AW8001 Bluetooth 4.0 module
Specification
Version 1.0
2013-7-25
Guangdong Transtek Medical Electronics Co.,Ltd
1.1 Introduction
The AW8001 Module is designed to be used in conjunction with an external
microcontroller running the application. The AW8001 integrates acomplete PHY, Link
Controller and Host single mode Bluetooth low energy subsystem and features a simple
SPI based interface to the application microcontroller. Qualified profiles, APIs and example
application are provided as part of the μBlue SDK which is easily portable to a range of
different application microcontrollers. This system segmentation allows the AW8001 to be
used with the best-fit microcontroller for a specific application as well as ease integration
and end product qualification as application and protocol stack does not share the same
microcontroller.
1.2 Features
•
•
•
•
•
•
•
•
•
•
•
•
•
Bluetooth Specification v4.0 compliant single mode low energy solution
Complete PHY, Link Controller and Host subsystem
Profiles and example applications provided in μBlue SDK
Cost and power optimized for slave operation
Simple SPI based Application Controller Interface (ACI)
Full Link Controller and Host security
1.9 to 3.6V operation
Linear voltage regulator
Step-down DC/DC voltage regulator providing up to 20% peak current reduction
Sub 14mA peak current with linear voltage regulator
Supports sub 10μA average current operation
Battery voltage monitor
Temperature sensor
1.3 APPLICATIONS
•
•
•
•
•
•
•
•
Sports and fitness sensors
Healthcare and medical sensors
Continua™ Version Two certified products
Remote controls
Watches
Mobile phone peripherals
Automation sensors
Proximity tags
Guangdong Transtek Medical Electronics Co.,Ltd
2.1 Product Information
AW8001 is a BT4.0 Module , It’s main physical features are the Bluetooth low energy
PHY and the Bluetooth low energy stack that handles the link controller and host stack. It
also includes additional analog sub-systems needed for the Bluetooth low energy operation,
such as power management and several oscillator options.
AW8001 block diagram
AW8001 has on-chip non-volatile memory for storing service configurations. This
on-chip storage lets you select and combine the necessary services for your application,
reducing the requirements on your application controller for handling all real-time
operations related to the Bluetooth low energy communication protocol.
AW8001 includes a power supply voltage monitor and a temperature sensor that
further reduces the requirements to the application controller. These features are
accessible through the Application Controller Interface (ACI).
AW8001 also offers an optional output signal that is activated before the radio
becomes active. This timing signal enables you to control the peak current drain of your
application, avoiding overload of your power supply (for most applications this is usually a
small battery). You can also use this timing signal to control the application circuitry,
avoiding noise interference when the AW8001 radio is operating.
A separate serial interface (UART) gives you access to the Bluetooth low energy Direct
Test Mode (DTM).This interface is used to control the Bluetooth low energy radio (RF PHY)
and is supported by commercially available Bluetooth test equipment used for Bluetooth
qualification. This serial interface also enables you to test radio performance and to
optimize your antenna.
Guangdong Transtek Medical Electronics Co.,Ltd
2.2 Operating conditions
The operating conditions are the physical parameters that nRF8001 can operate within.
2.3 Digital I/O signal levels
The digital I/O signal levels are defined Table. The operating conditions are: VDD = 3.0V, TA
= 40oC to +85oC (unless otherwise noted).
2.4 Radio characteristics
nRF8001 electrical characterization is defined in Table . The operating conditions are:
VDD = 3.0V, TA = 40oC to +85oC (unless otherwise noted).
Guangdong Transtek Medical Electronics Co.,Ltd
3.1 Mechanical Information
3.2 PIN Information
VCC
MOSI
SCK
/REQN
MISO
/RDYN
NC
RESET
GND
Guangdong Transtek Medical Electronics Co.,Ltd
3.3 Module Installation
Step1: Connect the Module to the connector , this connector can be a PCB or Pin header or
another , see following picture
Step2: Connect the Module PCBA to the Main PCBA , see following picture
Step3: Install the Main PCBA to the Product ,see following picture
Caution: When install the module , you must pay attention to the
temperature of the soldering iron(the soldering iron should be connect
to Ground ) , the temperature should be set at about 380℃ ; you must
pay attention to the electrostatic too , take action to avoid electrostatic .
And you must avoid short circuit when you connect the module.
Module FCC ID: OU9AW8001-LS
Guangdong Transtek Medical Electronics Co.,Ltd
Step4: The final Product, see following picture
Make sure that the module is fixed in the host and does not allow users to replace or
demolition.
Guangdong Transtek Medical Electronics Co., Ltd
Caution: Any changed or modifications not expressly approved by the party responsible for compliance
could void the user`s authority to operate this equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1)
this device may not cause harmful interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
Note: This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against
harmful interference in a residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or television reception,
which can be determined by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
—Reorient or relocate the receiving antenna.
—Increase the separation between the equipment and receiver.
—Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
—Consult the dealer or an experienced radio/TV technician for help.
This device complies with FCC radiation exposure limits set forth for an uncontrolled environment.
This device should be installed and must not be co-located or operating in conjunction with any other
antenna or transmitter.
The module in this product is labeled with its own FCC ID and the FCC ID is not visible when the module is
installed inside another device. To satisfy FCC exterior labeling requirements, the following text must be
placed on the exterior of the end product.
Contains Transmitter Module FCC ID: OU9AW8001-LS

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.6
Linearized                      : No
Author                          : 09010
Create Date                     : 2013:07:26 13:02:58Z
Modify Date                     : 2013:07:30 13:15:39+08:00
Has XFA                         : No
XMP Toolkit                     : Adobe XMP Core 5.4-c005 78.147326, 2012/08/23-13:03:03
Format                          : application/pdf
Creator                         : 09010
Title                           : E:\Kelvin work file\project file\LS产品\TSF1235系列PCB的项目【GBF-1064BT系列】\AW8001模块\AW8001  datasheet.doc
Creator Tool                    : pdfFactory Pro www.fineprint.com.cn
Metadata Date                   : 2013:07:30 13:15:39+08:00
Producer                        : pdfFactory Pro 2.23 (Windows XP Chinese)
Document ID                     : uuid:3dddef2e-fea6-4603-bc67-b45a2e3746e5
Instance ID                     : uuid:8c9010dd-be4b-482e-b0ac-62bcd456f768
Page Count                      : 8

EXIF Metadata provided by EXIF.tools