Transtek Medical Electronics AW8001-LS Bluetooth Module User Manual LS406 B
Guangdong Transtek Medical Electronics Co.,Ltd Bluetooth Module LS406 B
Contents
- 1. User Manual Rev1
- 2. User Manual for Host Rev1
- 3. User Manual Rev01
- 4. User manual Rev01
- 5. LS202-b1 manual
- 6. User Manual
User Manual for Host Rev1
version:1.0 User Manual Glass Body Fat Analyzer LS203-B Contains FCC ID: OU9AW8001-LS GUANGDONG TRANSTEK MEDICAL ELECTRONICS CO., LTD Zone A, 5/F., Investment Building, No. 12, Huizhan East Rd., Torch Development District, Zhongshan, Guangdong, 528437, China TEL:86-760-88282982 www.transtek.cn Thank you very much for selecting the Transtek Glass Body Fat Analyzer LS203-B. Please do read the user manual carefully and thoroughly so as to ensure the safe usage of this product, and keep the manual well for further reference in case you have problems. Table of Contents Table of Contents Safety Information Safety and Usage Information ................................................................................................... 2 Indications For Use ................................................................................................................ 2 Contraindications ....................................................................................................................... 3 Your Scale and Its Environment ............................................................................................... 3 Efficient Use of Your Scale ...................................................................................................... 3 Overview Device Components ................................................................................................................. 4 LCD Display .............................................................................................................................. 5 Initial Start-Up General Instructions ................................................................................................................. 6 Insert the Batteries ................................................................................................................... 6 Install App and Pair-up ................................................ ............................................................ 7 Start Measuring Select Measurement Unit .......................................................................................................... 8 Daily Measurement .................................................................................................................. 8 Manage Your Health Data Transmission .................................................................................................................... 9 Troubleshooting Error Prompt ............................................................................................................................. 10 When Measuring ... .................................................................................................................. 10-11 When Data Transmitting... ........................................................................................................ 12 Specifications ............................................................................................................................ 13 Maintenance ............................................................................................................................... 14 Warranty ...................................................................................................................................... 14 FCC Regulations ........................................................................................................................ 15 Appendix Table of Body Fat Level .......................................................................................................... Table of Body Water Level ...................................................................................................... Health Tips – About Body Fat ................................................................................................. EMC Guidance ......................................................................................................................... 16 16 17 17-21 Safety Information Safety Information Safety and Usage Information The warning signs and symbols are essential to ensure your correct and safe use of this product and protect you and others from injury. Please kindly find the meanings of the warning signs and symbols, which you may encounter in the label and user manual, as follows: Symbol for “THE OPERATION GUIDE MUST BE READ” Symbol for “MANUFACTURER” Symbol for “TYPE BF APPLIED PARTS” Symbol for “COMPLIES WITH MDD 93/42/ECC REQUIREMENTS” Symbol for “SERIAL NUMBER” Symbol for “INDOOR USE ONLY” Symbol for “DIRECT CURRENT” Symbol for “ENVIRONMENT PROTECTION – Waste electrical products should not be disposed of with household waste. Please recycle where facilities exist. Check with your local authority or retailer for recycling advice” The Bluetooth Combination Mark CONTRAINDICATIONS 1. This device is contraindicated for any female subject who may be suspected of, or is pregnant. Besides provided inaccurate readings, the affects of this device on the fetus are unknown. 2. This device is contraindicated for any person who is connected to a wearable or implantable electronic device or instrument such as a pacemaker or defibrillator. Your Scale and Its Environment To ensure your safety as well as the service life of your scale, please avoid using the scale under the following circumstances: Concurrent use of this device and implantable medical electronic instruments, e.g. Cardiac Pacemaker Concurrent use of this device and wearable medical electronic instruments, e.g. electrocardiograph Concurrent use of this device and other medical electronic instruments for life support, e.g. mechanical heart Slippery floor such as tile floor Jumping onto the platform immediately after bath or with wet hands Near a cell phone or microwave oven CAUTION Avoid storage in the following locations: Transtek’s Body Fat Analyzer offers you a seamless way to manage your health. Please be aware that this device is designed for adults’ self-measuring and self-monitoring body fat level. Any information provided by this device is in no way meant to treat, cure or prevent any disease or illness from happening. This device should not be used by anyone who is acutely or chronically ill, suffering from a disease or taking medications that affect your water levels. The accuracy of readings for these patients has not been verified. Specific medical advice should be obtained from a physician. Where there is water The device is equipped with automatic data transmission function. It may emit electromagnetic energy so as to perform its intended function. Nearby portable and mobile RF communications equipment can affect the performance of the device. Where in reach of the infants or children Kindly note that the use of accessories, transducers or cables other than those specified, with the exception of transducers and cables sold by the manufacturer as replacement parts for internal components, may result in increased EMISSIONS or decreased IMMUNITY of the device. Be aware that misuse of electrical equipments can cause electric shock, burns, fire and other hazards. The patient is an intended operator. The patient can perform all the operations in the manual, such as measurement, data transmitting, changing batteries. INDICATIONS FOR USE The Transtek Body Fat Analyzer measures weight and uses bio-electrical impedance analysis (BIA) technology to estimate body fat, total body water percentage, bone mass, and muscle mass in generally healthy adults 18 years of age or older. It is intended for use in the home / domestic setting only. Where the device may be exposed to extreme temperatures, humidity, moisture, direct sunlight, dust, or salt air Where there is risk of shock or drop Where you store chemicals or full of corrosive gases Efficient Use of Your Scale To ensure the accuracy of measurement, please follow below instructions when you start measurement. Place the scale on a flat, hard surface. Soft surface such as carpet will affect the performance of the scale. Step onto the platform with bare feet. Stand still and keep full contact with the electrodes until the measurement is complete. Start measurement at least two hours after Getting up or Dinning. Avoid measurement immediately after strenuous exercise, sauna or bath, drinking, and dinning. Always start measurement in the same time slot and on the same scale located on the same flat, hard surface. Overview Overview Device Components LCD Display LCD Display Electrode Electrode UNIT and activation Button Battery Compartment List 1. Glass Body Fat Analyzer LS203-B Kilogram Data transmitting Stone Pending to transmit to wireless wellness system Pound Low Battery Bioelectrical Impedance Analysis 2. Four AAA-size Alkaline Batteries (1.5V each) 3. User Manual Initial Start-Up General Instructions Transtek Glass Body Fat Analyzer LS203-B applies BIA (Bio-impedance Analysis) technology. A small amount of weak current flows through the human body so as to detect the bio-impedance and estimate body fat. The electrical current is small and may not be felt. This BIA technology is cheap, safe, non-invasive, toxic-free and harmless. It also possesses the characteristics of simple operation and abundant information. The current mentioned above is less than 1mA. However, please be aware that anyone with an wearable or implantable medical electronic instrument, such as a pacemaker, must avoid using this device. The intended use of this device is for adult’s indoor use only. Initial Start-Up Install App and Pair-Up With the advanced Bluetooth 4.0 technology applied, the mobile or portable equipments, which are equipped with Bluetooth function in line with BLE Technical Specifications as well as BLP Protocol established by global organization Bluetooth SIG, are capable to receive your personal health data. Just simply install the specially-designed app and pair up your scale with your mobile or portable equipments. Then you may enjoy the comprehensive health solution provided by Transtek. The App is now available in App Store You may search and install the app in your iPhone. Insert the Batteries Open the battery door in the back of the scale. Insert the batteries (4 x 1.5V AAA) into the battery compartment according to the polarity indications marked inside the compartment. Turn on Bluetooth and App. Make sure both are ON when pair-up is proceeding. Press and hold “UNIT” button in the back of the scale to start pair-up. Symbol and symbol will be shown on the LCD alternatively, indicating pair-up is proceeding. * The digits “8888” will be shown on the LCD. Close the battery door and wait until the digits “0.0kg” are shown on the LCD. If SUCCEED, symbol will be shown on the LCD. CAUTION When the symbol appears, the device will power off in four seconds. Then you shall replace with a new set of batteries. Please replace all four batteries in the same time. Do NOT mix the old batteries with the new one. Worn batteries are hazardous waste. Do NOT dispose of them together with the household garbage. Please refer to the local ordinances and recycling instructions regarding disposal of the worn batteries. If FAIL, symbol “E1” will be shown on the LCD. To remove primary batteries when me equipment is not likely to be used for some time. Not touch the patient and battery output simultaneously. Start Measuring Select Measurement Unit With batteries correctly installed, press “UNIT” button in the back of the scale to select measurement unit. The default measurement unit is “kg”. You may press “UNIT” button to choose among kilogram, stone and pound. Daily Measurement With original SENSE ON patent technology, the scale will automatically switch on as you step on the platform barefooted. Stand still and keep full contact with the electrodes until the LCD stops blinking “BIA”. When your scale is successfully paired with your iPhone and the Bluetooth is ON, it will process data transmission automatically. (Please refer to Data Transmission for more details.) CAUTION The normal measuring time cannot over 1 minute. After the measurement, please don’t stand on the scale for a long time. Continous to use the scale for a long time, the surface temperature may exceed 41℃, this will cause burns. Manage Your Health Data Transmission With the scale successfully pair-up with your iPhone, the measurement data will be automatically transmitted to your mobile via Bluetooth. The symbol will disappear after successful data transmission, and you may check your personal health data stored in your iPhone. If the data transmission fails, the symbol will remain. The pending measurement data will be temporarily kept in the scale and transmitted to your iPhone when next measurement is complete. Data transmitting Data ready to transmit to the App: -If SUCCEED, the symbol disappears; -If FAIL, the symbol remains. Bluetooth Module No.: AW8001 RF Frequency Range: 2402MHz to 2480 MHZ Output Power Range: 4 dBm Supply Voltage: 3V to 3.6V CAUTION Interference may occur in the vicinity of equipment marked with the following symbol the Analyzer may interfere vicinity electrical equipment. . And To enable the data transmission function, this product should be paired to a Bluetooth end at 2.4 GHz. How to mitigate possible interference? 1. The range between the Analyzer and the Bluetooth end should be reasonably close, from 1 meter to 10 meters. Please ensure no obstacles between the Analyzer and the Bluetooth end so as to obtain quality connection. 2. To avoid interference, other electronic devices (particularly those with Bluetooth transmission / Transmitter) should be kept at least 1 meter away from the Analyzer. Troubleshooting Troubleshooting Error Prompt Error Description Solution Overload. The device will power off in four seconds. Stop using this scale for measurement. Low Battery. The device will power off in four seconds. Replace all four batteries in the same time. Please purchase the authorized batteries for replacement. Failure of pairing up your scale with your iPhone. Please check below items: -Bluetooth is ON. -App is ON. -Both devices are within the transmission distance of Bluetooth. Problem Abnormal measuring results: - Too high; OR - Too low; OR - Huge difference between two recent measurement. Root Cause Incorrect posture Abnormal measuring results: - Too high; OR - Too low; OR - Huge difference between two recent measurement. 10 Cold Electrodes. Either your hands or your feet are too dry. Please step on the platform barefooted and stand still. The device is located on the soft ground such as a carpet OR on a rugged surface. Please place the device on a flat, hard surface. Cold body that may results in bad blood circulation. Warm up your hands and feet to resume blood circulation and then measure again. The device powers off automatically. Place the device in a warm room for a while and then measure again. Wipe your feet with a damp cloth, keeping them slightly damp when starting measurement. Install the batteries. (Please refer to Insert the Batteries) Worn batteries. Replace all four batteries in the same time. Please purchase the authorized batteries for replacement. Solution CANNOT proceed to analyze body fat Solution Batteries not yet installed. No display on LCD when the device powers on. When Measuring ... Problem Root Cause Step onto the platform wearing socks or shoes. Low battery. Please keep barefooted during the measurement, and keep full contact with the electrodes as well. Replace all four batteries in the same time. Please purchase the authorized batteries for replacement. 11 Troubleshooting Specifications Specifications When Data Transmitting ... Problem Root Cause Bluetooth is OFF. Product Name Solution Turn ON the Bluetooth via “Setting >> General >> Bluetooth”. Scale: 321x321x23.5mm Dimension Net Weight App is OFF. Data transmission failed. Press the icon to turn ON your app. Display Measurement Unit Out of range of Bluetooth transmission. Place your iPhone closer to the scale. Glass Body Fat Analyzer (LS203-B) Measurement Range Division Accuracy Panel: 321x321x6mm Approximately 2kg ( Excluding the dry cells) Blue LCD with White Backlight V.A.: 74x53mm Kilogram / Stone / Pound 5kg to 200kg / 0st: 11lb to 31st: 7lb / 11lb to 441lb 0.1kg / 0.2lb 0-50kg: ±0.3kg; 100-150kg: ±0.5kg; 50-100kg: ±0.4kg; 150-200kg: ±0.7kg Working Environment Temperature: 0 ℃ to 40 ℃ Pressure: 80kPa to 105kPa Storage Environment Temperature: -20 ℃ to 60 ℃ Humidity: 10%RH to 93% RH Power Source Humidity: ≤90% RH 6V (Four AAA-size Alkaline Batteries) Auto-ON SENSE ON technology Auto-OFF About 10 seconds while showing 0.0 About 15 seconds after the weight data is locked Accessories 1. Four AAA-size Alkaline Batteries 2. User Manual Mode of Operation Continuous Operation Protection Against Ingress of Water IPX0 Protection against electric shock Internally powered ME equipment Software Version 1.0 Applied part Type BF applied part, including the whole top surface Note: Not intended to be sterilized. Not for use in an oxygen rich environment. 12 About the Accuracy of This Product This product passes strict inspection before delivery and therefore its accuracy is guaranteed by the manufacturer. Please refer to the above table for the descriptions on accuracy. This product is specially designed for body fat analysis as well as weight measurement. It should NOT be used by anyone during the process of transaction for verification of goods’ weight. 13 Maintenance Maintenance When carrying out usual maintenance, please ensure practice of the following Do’s and Don’ts: FCC Regulations FCC Regulations FCC User Guide Information DO use a dry soft cloth to wipe the dust. Radio Frequency Interface Requirements - FCC DO use a wet soft cloth, dipped into water and wrung out, to wipe the dirt. Then use a dry soft cloth to dry up the device. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: Reorient or relocate the receiving antenna; Increase the separation between the equipment and receiver; Connect the equipment into an outlet on a circuit different from that to which the receiver is connected; Consult the dealer or an experienced radio / TV technician for help. Radio Transmitters (Part 15) DON’T wash the device with water or immerse it in water. DON’T use propellant, abrasive or other chemicals to wipe the dirt in avoidance of discolor or malfunction. DON’T disassemble this device. If you have any problems, please contact Transtek. (Please refer to Warranty for contact information) Warranty Transtek warrants its products free of defects in materials and workmanship in normal use for a period of TWO years from the date of retail purchase. This warranty does NOT cover damages caused by misuse or abuse, including but not limited to: Failure caused by unauthorized repairs or modifications; Damage caused by shock or drop during transportation; Failure caused by improper operation inconsistent with the instructions stated in this user manual; Malfunction or damage from failure to provide the recommended maintenance; Damage caused by improper use of power supply. Should this device require maintenance (or replacement at our option) under warranty, please deliver the original package to GUANGDONG TRANSTEK MEDICAL ELECTRONICS CO., LTD prepaid. Please return the store receipt (with the retail purchase date) and a note with reasons to return on it as well. GUANGDONG TRANSTEK MEDICAL ELECTRONICS CO., LTD Zone A, 5/F., Investment Building, No. 12 Huizhan East Rd., Torch Development District, Zhongshan, 528437, Guangdong, China Tel: 86-760-88282982 Website: http://www.transtek.cn 14 This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. FCC RF Exposure Guidelines Safety Information Reducing RF Exposure - Use Properly Only operate the device in accordance with the instructions supplied. This device complies with FCC radiation exposure limits set forth for an uncontrolled environment. 15 Appendix Appendix Table of Body Fat Level (Unit: %) Age EMC Guidance Man / Sportsman Table 1 – Guidance and MANUFACTURER’S declaration – ELECTROMAGNETIC EMISSIONS – for all ME EQUIPMENT and ME SYSTEMS Woman / Sportswoman Low Normal High V. High Low Normal High V. High 20-29 <13 13.1-20 20.1-23 >23 <19 19.1-28 28.1-31 >31 30-39 <14 14.1-21 21.1-24 >24 <20 20.1-29 29.1-32 >32 40-49 <16 16.1-23 23.1-26 >26 <22 22.1-30 30.1-33 >33 50-59 <17 17.1-24 24.1-27 >27 <23 23.1-31 31.1-34 >34 60+ <18 18.1-25 25.1-28 >28 <24 24.1-32 32.1-35 >35 Table of Body Water Level (Unit: %) Gender Body Fat Percentage Range Optimal Total Body Water Percentage Range 4-14 70-63 15-21 63-57 22-24 57-55 ≥25 55-37 4-20 70-58 21-29 58-52 30-32 52-49 ≥33 49-37 Men Women Guidance and manufacturer’s declaration – electromagnetic emissions The device is intended for use in the electromagnetic environment specified below. The customer or the user of the device should assure that it is used in such an environment. Emission test Compliance RF emission CISPR 11 Group 1 RF emission CISPR 11 Class B Harmonic emissions IEC 61000-3-2 Not applicable Voltage fluctuations/ flicker emissions IEC 61000-3-3 Not applicable Electromagnetic environment – guidance The device uses RF energy only for its internal function. Therefore, its RF emissions are very low and are not likely to cause any interference in nearby electronic equipment. Source: Derived fr. Wang & Deurenberg: “Hydration of fat-free body mass”. American Journal Clin Nutr 1999, 69833-841 Health Tips - About Body Fat Fat is essential for human body. It can not only store energy and protect viscera, but also regulate body temperature and maintain normal physiological function of human body. However, too much body fat is harmful to human body. It is always accompanied by Fatty Liver, diabetes, coronary heart disease, etc. Therefore self-measuring and self-monitoring body fat level are beneficial to your health. Since we can’t judge body fat level simply by our weight, this body fat analyzer LS203-B , with BIA (Bio-impedance Analysis) technology applied, is an accurate device that offers a quick and comfortable way to obtain your body fat level. 16 17 Appendix Appendix Table 2 – Guidance and MANUFACTURER’S declaration – electromagnetic IMMUNITY – for all ME EQUIPMENT and ME SYSTEMS Guidance and manufacture’s declaration – electromagnetic immunity The device is intended for use in the electromagnetic environment specified below. The customer or the user of the device should assure that it is used in such an environment. Immunity test IEC 60601 test level Compliance level Electrostatic discharge (ESD) IEC 61000-4-2 ±6 kV contact ±8 kV air ±6 kV contact ±8 kV air Electrical fast transient/burst IEC 61000-4-4 ±2 kV for power supply lines Not applicable Surge IEC 61000-4-5 ±1 kV line(s) to line(s) Not applicable Electromagnetic environment - guidance 40% UT (60% dip in UT) for 5 cycles 70% UT (30% dip in UT) for 25 cycles Guidance and manufacture’s declaration – electromagnetic immunity The device is intended for use in the electromagnetic environment specified below. The customer or the user of the device should assure that it is used in such an environment. Immunity test IEC 60601 test level Compliance level Floors should be wood, concrete or ceramic tile. If floor are covered with synthetic material, the relative humidity should be at least 30%. <5% UT (>95% dip in UT) for 0.5 cycle Voltage dips, short interruptions and voltage variations on power supply input lines IEC 61000-4-11 Table 4 Guidance and manufacture’s declaration – electromagnetic immunity – for ME EQUIPMENT and ME SYSTEMS that are not LIFE-SUPPORTING Conducted RF 3 Vrms IEC 61000-4-6 150 kHz to 80 MHz Radiated RF 3 V/m 80 MHz IEC 61000-4-3 to 2.5 GHz Not applicable <5% UT (>95% dip in UT) for 5 sec 3 Vrms 3 V/m Electromagnetic environment guidance Portable and mobile RF communications equipment should be used no closer to any part of the device including cables, than the recommended separation distance calculated from the equation applicable to the frequency of the transmitter. Recommended separation distance d = 1.167 d = 1.167 80 MHz to 800 MHz d = 2.333 800 MHz to 2.5 GHz where P is the maximum output power rating of the transmitter in watts (W) according to the transmitter manufacturer and d is the recommended separation distance in metres (m). Field strengths from fixed RF transmitters, as determined by an electromagnetic site survey,a should be less than the compliance level in each frequency range. Interference may occur in the vicinity of equipment marked with the following symbol: Power frequency magnetic fields should be at levels characteristic of a typical 3A/m 3A/m location in a typical commercial or hospital environment. UT is the a.c. mains voltage prior to application of the test level. Power frequency (50Hz) magnetic field IEC 61000-4-8 NOTE 18 19 Appendix NOTE 1 At 80 MHz and 800 MHz, the higher frequency range applies. NOTE 2 These guidelines may not apply in all situations. Electromagnetic propagation is affected by absorption and reflection from structures, objects and people. a Field strengths from fixed transmitters, such as base stations for radio (cellular/cordless) telephones and land mobile radios, amateur radio, AM and FM radio broadcast and TV broadcast cannot be predicted theoretically with accuracy. To assess the electromagnetic environment due to fixed RF transmitters, an electromagnetic site survey should be considered. If the measured field strength in the location in which the device is used exceeds the applicable RF compliance level above, the device should be observed to verify normal operation. If abnormal performance is observed, additional measures may be necessary, such as reorienting or relocating the device. b Over the frequency range 150 kHz to 80 MHz, field strengths should be less than 3 V/m. Appendix Table 6 – Recommended separation distances between portable and mobile RF communications equipment and the ME EQUIPMENT or ME SYSTEM – for ME EQUIPMENT and ME SYSTEMS that are not LIFE-SUPPORTING Recommended separation distances between portable and mobile RF communications equipment at the LS203-B The device is intended for use in an electromagnetic environment in which radiated RF disturbances are controlled. The customer or the user of the device c an help prevent electromagnetic interference by maintaining a minimum distance between portable and mobile RF communications equipment (transmitters) and the device as recommended below, according to the maximum output power of the communications equipment. Rated maximum output power of transmitter (W) Separation distance according to frequency of transmitter (m) 150 kHz to 80 MHz 80 MHz to 800 MHz 800 MHz to 2.5 GHz d = 1.167 d = 1.167 d = 2.333 0.01 N/A 0.117 0.233 0.1 N/A 0.369 0.738 10 N/A 1.167 2.333 N/A 3.690 7.377 100 N/A 11.67 23.33 For transmitters rated at a maximum output power not listed above, the recommended separation distance d in meters (m) can be estimated using the equation applicable to the frequency of the transmitter, where P is the maximum output power rating of the transmitter in watts (W) according to the transmitter manufacturer. NOTE 1 At 80 MHz and 800 MHz, the separation distance for the higher frequency range applies. NOTE 2 These guidelines may not apply in all situations. Electromagnetic propagation is affected by absorption and reflection from structures, objects and people. 20 21
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.6 Linearized : Yes Author : Shuting Create Date : 2013:05:09 08:44:28+08:00 Keywords : GBF-1251-B Modify Date : 2013:08:07 08:49:42+08:00 Subject : User Manual XMP Toolkit : Adobe XMP Core 5.4-c005 78.147326, 2012/08/23-13:03:03 Format : application/pdf Title : LS406-B user manual Description : User Manual Creator : Shuting Creator Tool : Adobe Illustrator CS5 Metadata Date : 2013:08:07 08:49:42+08:00 Thumbnail Width : 40 Thumbnail Height : 256 Thumbnail Format : JPEG Thumbnail Image : (Binary data 2967 bytes, use -b option to extract) Original Document ID : uuid:9E3E5C9A8C81DB118734DB58FDDE4BA7 Document ID : xmp.did:699E7D9841B8E211BB1CBF23DB8308F5 Instance ID : uuid:2e440701-39f2-467d-8906-157e4b86ccd5 Rendition Class : proof:pdf History Action : converted, saved, converted, converted, saved, converted, saved, converted, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved History Instance ID : xmp.iid:D07F11740720681191099C3B601C4548, xmp.iid:FC7F117407206811B628E3BF27C8C41B, xmp.iid:FD7F117407206811B628E3BF27C8C41B, xmp.iid:0CC3BD25102DDD1181B594070CEB88D9, xmp.iid:03E540664A3DDD11BD33D3EB8D3A1068, xmp.iid:6D6AE2A5723EDD11A6F1BABF7C5A7A51, xmp.iid:20383BFEA441DD11A6AECB58D53C8B28, xmp.iid:096F577ABE41DD11A6AECB58D53C8B28, xmp.iid:AB13E990200911689FE8CB9EA85C5459, xmp.iid:95D9A2DF7848DD11BB47877F8DDF9079, xmp.iid:F87F117407206811B34B80FC905F8DB1, xmp.iid:FE7F11740720681197A5C6DA8C2593EE, xmp.iid:FF7F11740720681197A5C6DA8C2593EE, xmp.iid:D5E97F3291E4DE11831BCC4BA24AAFD8, xmp.iid:3E09327B1FEADE119648D46DE661B201, xmp.iid:A8F46C6799EBDE118B29BF0F76361FFD, xmp.iid:233794C82A12DF11A1FB8DE093AEEF16, xmp.iid:E9171D43F3ABDF119F67BD126A85E7C0, xmp.iid:ED171D43F3ABDF119F67BD126A85E7C0, xmp.iid:A98329CBEEDCDF119F6AFE1DA0EB4A56, xmp.iid:F0D7C34F6BE9DF11BB38870380B6B2A6, xmp.iid:3097A67DCCEADF11AC9EC8ACF64A7DDE, xmp.iid:9550DF26AFEBDF119A34BB36D9091C95, xmp.iid:91B2A8E3B31EE0118388C60B75F0B421, xmp.iid:C66F62307E1FE011B297ADA3E90C4992, xmp.iid:32111635E540E211A2A3C2ACD38E298D, xmp.iid:D8BE93E0064BE211992AB2AA5473309D, xmp.iid:925B3A1E5351E211BB2AA5B5C8B3A954, xmp.iid:119378523FB8E2119103F28CE45EF15D, xmp.iid:0D2DAF963FB8E211B953FD11DEEDFEF3, xmp.iid:699E7D9841B8E211BB1CBF23DB8308F5 History When : 2008:04:17 14:19:10+05:30, 2008:05:22 14:51:08-07:00, 2008:05:22 15:15:38-07:00, 2008:05:28 17:07:17-07:00, 2008:06:18 22:24:35+07:00, 2008:06:19 20:31:09-07:00, 2008:06:24 13:29:32+08:00, 2008:06:24 15:24:18+08:00, 2008:06:26 06:04:07-07:00, 2008:07:02 13:54:46-07:00, 2008:07:21 16:58:27+05:30, 2008:09:05 04:29:47-07:00, 2008:09:05 04:30:01-07:00, 2009:12:09 17:43:05+08:00, 2009:12:16 16:46:19+08:00, 2009:12:18 17:47:07+08:00, 2010:02:05 15:48+08:00, 2010:08:20 08:39:57+08:00, 2010:08:20 12:32:03+08:00, 2010:10:21 16:40:01+08:00, 2010:11:06 14:40+08:00, 2010:11:08 09:13:48+08:00, 2010:11:09 11:24:26+08:00, 2011:01:13 11:20:28+08:00, 2011:01:14 09:32:45+08:00, 2012:12:08 13:29:51+08:00, 2012:12:21 08:57:37+08:00, 2012:12:29 16:12:58+08:00, 2013:05:09 08:28:08+08:00, 2013:05:09 08:30:02+08:00, 2013:05:09 08:44:24+08:00 History Software Agent : Adobe Illustrator CS4, Adobe Illustrator CS4, Adobe Illustrator CS4, Adobe Illustrator CS4, Adobe Illustrator CS4, Adobe Illustrator CS4, Adobe Illustrator CS4, Adobe Illustrator CS4, Adobe Illustrator CS4, Adobe Illustrator CS4, Adobe Illustrator CS4, Adobe Illustrator CS4, Adobe Illustrator CS4, Adobe Illustrator CS4, Adobe Illustrator CS4, Adobe Illustrator CS4, Adobe Illustrator CS4, Adobe Illustrator CS4, Adobe Illustrator CS4, Adobe Illustrator CS4, Adobe Illustrator CS4, Adobe Illustrator CS4, Adobe Illustrator CS4, Adobe Illustrator CS4, Adobe Illustrator CS4, Adobe Illustrator CS5, Adobe Illustrator CS5, Adobe Illustrator CS5, Adobe Illustrator CS5, Adobe Illustrator CS5, Adobe Illustrator CS5 History Changed : /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, / History Params : from application/vnd.adobe.illustrator to application/vnd.adobe.illustrator Derived From Instance ID : uuid:1e64ed95-ca85-423b-9266-53eb10896892 Derived From Document ID : xmp.did:0D2DAF963FB8E211B953FD11DEEDFEF3 Derived From Original Document ID: uuid:9E3E5C9A8C81DB118734DB58FDDE4BA7 Derived From Rendition Class : proof:pdf Startup Profile : Basic RGB N Pages : 1 Has Visible Transparency : True Has Visible Overprint : True Max Page Size W : 257.000161 Max Page Size H : 182.000260 Max Page Size Unit : Millimeters Font Name : Arial-Black, Arial-ItalicMT, ArialMT, Arial-BoldMT, TimesNewRomanPS-ItalicMT, AdobeSongStd-Light, SimHei Font Family : Arial, Arial, Arial, Arial, Times New Roman, Adobe 宋体 Std, 黑体 Font Face : Black, Italic, Regular, Bold, Italic, L, Regular Font Type : Open Type, Open Type, Open Type, Open Type, Open Type, Open Type, TrueType Font Version : Version 2.40, Version 2.90, Version 3.00, Version 3.00, Version 2.90, Version 5.002;PS 5.002;hotconv 1.0.49;makeotf.lib2.0.15106, Version 3.02 Font Composite : False, False, False, False, False, False, False Font File Name : ariblk.TTF, ARIALI.TTF, ARIAL.TTF, ARIALBD.TTF, TIMESI.TTF, AdobeSongStd-Light.otf, simhei.ttf Plate Names : Cyan, Magenta, Yellow, Black, PANTONE 286 CVU Swatch Groups Colorants Tint : 100.000000 Swatch Groups Group Name : 初始屏幕 Swatch Groups Group Type : 1 Swatch Groups Colorants Swatch Name: R=180 G=58 B=228 Swatch Groups Colorants Mode : CMYK Swatch Groups Colorants Type : PROCESS Swatch Groups Colorants Cyan : 48.046899 Swatch Groups Colorants Magenta : 78.906298 Swatch Groups Colorants Yellow : 0.000000 Swatch Groups Colorants Black : 0.000000 Producer : Adobe PDF library 9.90 Page Count : 12EXIF Metadata provided by EXIF.tools