Tranwo Technology MA8802A 2.4GHz Digital Audio Video Module User Manual MA8802A 2M RF module spec
Tranwo Technology Corp 2.4GHz Digital Audio Video Module MA8802A 2M RF module spec
User Manual
MA-8802A 2.4GHz Digital Audio Video Module Date: 2013/3/20 A. Features Operating frequency range from 2408 to 2468 MHz 31 hopping channels Maximum data rate 2 Mbps (GFSK) 4-wire SPI interface support , 16MHz clock rate Modulation scheme : GFSK The 16-bit CRC checking Packet retransmission mechanism Power supply range: 3.3V Transmission range: 250 m (Line of sight) Outline: 23.23x 21.22 x 3.75 mm B. Applications Digital Baby Monitor Wireless Video Door phone Security Camera MA-8802A Preliminary data subjects to change without notice MA-8802A 2.4GHz Digital Audio Video Module Date: 2013/3/20 C: Specification Parameter Min. Typ. Max. Unit 3.3 3.6 Electrical Section Supply Voltage Supply current in TX mode 120 mA Supply current in RX mode 40 mA RF Section Modulation Mode Operating Frequency GFSK 2408 2468 MHz Channel Bandwidth MHz Channel 31 channels Data Rate 2M bps Transmission Power +18 dBm Power control range 0~18 dB Transmitter Section Power control resolution -- -- dB Receiver Section Non-overlay channel spacing MHz Sensitivity -90(Typical) dBm Operation Operating Temperature -20 +85 ℃ Storage Temperature -40 +85 ℃ Preliminary data subjects to change without notice MA-8802A 2.4GHz Digital Audio Video Module Date: 2013/3/20 D: Pin Assignment No. Marks Function VCC Power Supply GND Ground IRQ Maskable interrupt pin. Active low MISO SPI Slave Data Output , with tri-state option MOSI SPI Slave Data Input SCK SPI Clock CNS SPI Ship select CE Chip Enable Activates RX or TX mode EN N/A 10 GND Ground Model: MA-8802A Preliminary data subjects to change without notice MA-8802A 2.4GHz Digital Audio Video Module Date: 2013/3/20 E: Mechanical Dimension Preliminary data subjects to change without notice MA-8802A 2.4GHz Digital Audio Video Module Federal Communication Commission Interference Statement This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures: Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. Radiation Exposure Statement: This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body. Preliminary data subjects to change without notice MA-8802A 2.4GHz Digital Audio Video Module This device is intended only for OEM integrators under the following conditions: 1) The antenna must be installed such that 20 cm is maintained between the antenna and users, and 2) The transmitter module may not be co-located with any other transmitter or antenna. 3) Module approval valid only when the module is installed in the tested host or compatible series of host As long as 3 conditions above are met, further transmitter test will not be required. However, the OEM integrator is still responsible for testing their end-product for any additional compliance requirements required with this module installed IMPORTANT NOTE: In the event that these conditions can not be met (for example certain laptop configurations or co-location with another transmitter), then the FCC authorization is no longer considered valid and the FCC ID can not be used on the final product. In these circumstances, the OEM integrator will be responsible for re-evaluating the end product (including the transmitter) and obtaining a separate FCC authorization. End Product Labeling This transmitter module is authorized only for use in device where the antenna may be installed such that 20 cm may be maintained between the antenna and users. The final end product must be labeled in a visible area with the following: “Contains FCC ID: O6L-MA8802A”. Manual Information To the End User The OEM integrator has to be aware not to provide information to the end user regarding how to install or remove this RF module in the user’s manual of the end product which integrates this module. The end user manual shall include all required regulatory information/warning as show in this manual. Preliminary data subjects to change without notice MA-8802A 2.4GHz Digital Audio Video Module Industry Canada statement: This device complies with ISED’s licence-exempt RSSs. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Le présent appareil est conforme aux CNR d’ ISED applicables aux appareils radio exempts de licence. L’exploitation est autorisée aux deux conditions suivantes : (1) le dispositif ne doit pas produire de brouillage préjudiciable, et (2) ce dispositif doit accepter tout brouillage reçu, y compris un brouillage susceptible de provoquer un fonctionnement indésirable. Radiation Exposure Statement: This equipment complies with ISED radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body. Déclaration d'exposition aux radiations: Cet équipement est conforme aux limites d'exposition aux rayonnements ISED établies pour un environnement non contrôlé. Cet équipement doit être installé et utilisé avec un minimum de 20 cm de distance entre la source de rayonnement et votre corps. This device is intended only for OEM integrators under the following conditions: (For module device use) 1) The antenna must be installed such that 20 cm is maintained between the antenna and users, and 2) The transmitter module may not be co-located with any other transmitter or antenna. As long as 2 conditions above are met, further transmitter test will not be required. However, the OEM integrator is still responsible for testing their end-product for any additional compliance requirements required with this module installed. Cet appareil est conçu uniquement pour les intégrateurs OEM dans les conditions suivantes: (Pour utilisation de dispositif module) 1) L'antenne doit être installée de telle sorte qu'une distance de 20 cm est respectée entre l'antenne et les utilisateurs, et 2) Le module émetteur peut ne pas être coïmplanté avec un autre émetteur ou antenne. Tant que les 2 conditions ci-dessus sont remplies, des essais supplémentaires sur l'émetteur ne seront pas nécessaires. Toutefois, l'intégrateur OEM est toujours responsable des essais sur son produit final pour toutes exigences de conformité supplémentaires requis pour ce module installé. Preliminary data subjects to change without notice MA-8802A 2.4GHz Digital Audio Video Module IMPORTANT NOTE: In the event that these conditions can not be met (for example certain laptop configurations or co-location with another transmitter), then the Canada authorization is no longer considered valid and the IC ID can not be used on the final product. In these circumstances, the OEM integrator will be responsible for re-evaluating the end product (including the transmitter) and obtaining a separate Canada authorization. NOTE IMPORTANTE: Dans le cas où ces conditions ne peuvent être satisfaites (par exemple pour certaines configurations d'ordinateur portable ou de certaines co-localisation avec un autre émetteur), l'autorisation du Canada n'est plus considéré comme valide et l'ID IC ne peut pas être utilisé sur le produit final. Dans ces circonstances, l'intégrateur OEM sera chargé de réévaluer le produit final (y compris l'émetteur) et l'obtention d'une autorisation distincte au Canada. End Product Labeling This transmitter module is authorized only for use in device where the antenna may be installed such that 20 cm may be maintained between the antenna and users. The final end product must be labeled in a visible area with the following: “Contains IC: 8522A-MA8802A”. Plaque signalétique du produit final Ce module émetteur est autorisé uniquement pour une utilisation dans un dispositif où l'antenne peut être installée de telle sorte qu'une distance de 20cm peut être maintenue entre l'antenne et les utilisateurs. Le produit final doit être étiqueté dans un endroit visible avec l'inscription suivante: "Contient des IC: 8522A-MA8802A ". Manual Information To the End User The OEM integrator has to be aware not to provide information to the end user regarding how to install or remove this RF module in the user’s manual of the end product which integrates this module. The end user manual shall include all required regulatory information/warning as show in this manual. Manuel d'information à l'utilisateur final L'intégrateur OEM doit être conscient de ne pas fournir des informations à l'utilisateur final quant à la façon d'installer ou de supprimer ce module RF dans le manuel de l'utilisateur du produit final qui intègre ce module. Le manuel de l'utilisateur final doit inclure toutes les informations réglementaires requises et avertissements comme indiqué dans ce manuel. Preliminary data subjects to change without notice Approved antenna(s) list Type Gain(dBi) Brand Manufacturer Dipole TRANWO TRANWO PCB 0.07 TRANWO TRANWO Dipole -0.8343 TRANWO TRANWO
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.6 Linearized : Yes Author : Asen Create Date : 2014:01:03 19:55:48+08:00 Modify Date : 2018:07:19 16:48:47+08:00 Has XFA : No XMP Toolkit : Adobe XMP Core 5.2-c001 63.139439, 2010/09/27-13:37:26 Creator Tool : PScript5.dll Version 5.2.2 Metadata Date : 2018:07:19 16:48:47+08:00 Producer : Acrobat Distiller 9.5.2 (Windows) Format : application/pdf Title : Microsoft Word - MA8802A_2M RF module_spec.doc Creator : Asen Document ID : uuid:6fede9c3-4dc3-4c27-b862-5bab09de32b2 Instance ID : uuid:a5285c29-618c-462e-9a5c-2f8593609ba7 Page Count : 9EXIF Metadata provided by EXIF.tools