Tranwo Technology MDD24R2001 2.4GHz DIGITAL AV module User Manual

Tranwo Technology Corp 2.4GHz DIGITAL AV module

Users Manual

Date: 2011/5/16 Preliminary data subjects to change without notice 1 MDD-24R2001 2.4GHz Digital Audio Video Modules A. Features Operating frequency range from 2403 to 2475 MHz Maximum 25 hopping channels Maximum data rate 12 Mbps (@16QAM) 4-wire SPI interface support max. 30MHz clock rate Modulation scheme : 16QAM,QPSK The 16-bit CRC checking Hardware retransmission for packets Power supply range: 2.7 ~ 3.3V Transmission range: 250 m (Line of sight) Outline: 20.40 x 27.65 x 4.4 mm CE & FCC compliance B. Applications Digital AV Sender Digital Baby Monitor Wireless Video Door phone Security Camera Portable Video Recorder MDD-24R2001 TRANWO CONFIDENTIAL
Date: 2011/5/16 Preliminary data subjects to change without notice 2 MDD-24R2001 2.4GHz Digital Audio Video Modules C: Specification Parameter Min. Typ. Max. Unit Electrical Section Supply Voltage 4.9 5.0 5.1 V Supply current in TX mode 200 mA Supply current in RX mode 65 mA RF Section Modulation Mode QPSK,16QAM Operating Frequency 2403 ~ 2475 MHz Channel Bandwidth 3 MHz Channel 25 channels Data Rate 3M ~ 12M bps Transmitter Section Transmission Power +14 @16QAM +18 @QPSK dBm Power control range 40 dB Power control resolution 1 1 3 dB Receiver Section Overlay channel spacing 1 MHz Sensitivity -78 @ 16QAM -86 @ QPSK dBm Operation Operating Temperature -10 ~ +60 ℃ Storage Temperature -20 ~ +70 ℃ TRANWO CONFIDENTIAL
Date: 2011/5/16 Preliminary data subjects to change without notice 3 MDD-24R2001 2.4GHz Digital Audio Video Modules D: Pin Assignment No. Marks Function 1 VCC Power Supply 2 GND Ground 3 CLK12M 12MHz clock output 4 IRQ_N Interrupt indication for external MCU 5 CS_N Chip Selection 6 SDO Serial data output 7 SDI Serial data input 8 SCK Serial clock input 9 RST_N Negative active reset input 10 CLK32K 32KHz clock output Model: MDD-24R2001 TRANWO CONFIDENTIAL
Date: 2011/5/16 Preliminary data subjects to change without notice 4 MDD-24R2001 2.4GHz Digital Audio Video Modules E: Mechanical Dimension TRANWO CONFIDENTIAL
Date: 2011/5/16 Preliminary data subjects to change without notice 5 MDD-24R2001 2.4GHz Digital Audio Video Modules Module User Manual The purpose of this manual is to explain correct way how to integrate module MDD-24R2001 to the end product. It includes procedures that shall assist you to avoid unforeseen problems. This manual presents information that shows how module and OEM product, where module integrated, complies with regulations in certain regions. Note that any modifications, not expressly approved by the manufacturer could void the authority to operate in these regions. Integration The RF module, model MDD-24R2001 has to be installed and used in accordance with the technical installation instructions provided by the manufacturer. For detail information concerning type approval of this module please contact the authorized local distributor or the manufacturer. The system may only be implemented in the configuration that was authorized. USA-Federal Communications Commission (FCC) This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions : (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Labeling The RF module MDD-24R002 for controller labeled as below. The label that is placed on the module is too small to hold the required FCC information, then that information appear in the user manual for this device. In addition, the” Contains FCC ID : O6L-MDD24R2001” label also must be placed on the outside of the end product system. TRANWO CONFIDENTIAL
Date: 2011/5/16 Preliminary data subjects to change without notice 6 MDD-24R2001 2.4GHz Digital Audio Video Modules This device is to be used only for mobile and fixed applications. The antenna(s) used for this transmitter must be installed to provide a separation distance of at least 20cm from all persons and must not be collocated or operating in conjunction with any other antenna or transmitter. OEM integrators must be provided with antenna installation instructions. OEM integrators and end-users must be provided with transmitter operation conditions for satisfying RF exposure compliance. This grant is valid only when the device is sold to OEM integrators and the OEM integrators are instructed to ensure that the end-user has no manual instruction to remove or install the device. Separate approval is required for all other operating configurations, including portable configurations with respect to 2.1093 and different antenna configurations. TRANWO CONFIDENTIAL

Navigation menu