Tranwo Technology TTD-80R Wireless digital child tracker User Manual Manual P1

Tranwo Technology Corp Wireless digital child tracker Manual P1

Contents

Manual P1

What You GetProduct LayoutImportant InformationSetting Up Set up the Child Unit Set up the Parent Unit Check the connectionUsing the Child Tracker Channel selection function Adding Child units Removing Child units Battery low indicator Directional indicator function Warning range setup Find functionFeaturesTroubleshootingTechnical SpecificationCare and maintenance.........................................1........................................2.............................4................................................5.................................................................................589...........................10...................11.................................13............................13.............................14................14.............................16.........................................17..................................................19......................................20..........................21..........................21
1Parent Unit Child Unit Child Unit charger Child Unit charger main power adapter LIR2450 Li+ 3.6V rechargeable battery for Child Unit 2 x AAA 1.5V non rechargeable alkaline batteries for Parent Unit User’s ManualWhat You Get....................................................
2Product Layout134526789212356478910A, Parent Unit Fig. 1 B, Chid Unit Fig. 2
3What You GetFind button/Initiation child unit buttonDirectional indicator LEDChannel indicator LEDChannel selection button/Deletion child unit buttonSpeakerPower/battery low indicator LEDPower off/warning range <near/normal/far> switchBelt clipbattery covercharge sensorBattery coverClaspPower/battery low indicator LEDSpeakerFind button/lnitiation child unit buttonCharger sensorCharger indicator LEDpower adapter jackCharger main power adapterA, Parent Unit Fig. 1 B, Chid Unit Fig. 212345678912345678910
4Setting UpImportant Information1. If traveling abroad, make sure that the voltage shown on the mains power adapter corresponds to the local mains power before connection to the power supply.2. To prevent electric shock, do not open the case of the Child Unit and Parent Unit (except battery covers)3. Risk of explosion if batteries are replaced by an incorrect type. For the Child Unit, always use LIR2450 3.6V Li+ rechargeable battery. For the Parent Unit, suggestion use AAA non rechargeable 1.5V alkaline batteries.
5Setting UpImportant InformationSet up the Child UnitWhen you use this product for the rst time, please charge it.1. How to install the batteries(1)Insert the two belt clips into the battery cover on the back of the Child unit and then open the battery cover by turning it counterclockwise. (2) Install the LIR2450 battery into the battery cover and turn the belt clips clockwise to combine the battery cover with the Child unit. (Please note the poles when installing batteries.) In the meantime, the Power LED will light red.
6Setting Up2.How to chargeOK1 2 3 4(1) Insert the Charger Adapter into the power socket. (2) Connect the Charger Adapter with the Charger. In the meantime, the Charger  indicatorwillashredandgreenforthreetimesrespectivelyandthengoout.(3) Connect the Child unit to the Charger in the direction as illustrated, and the Charger indicator will light red to indicate that it is being charged. When the Charger indicator lights green, it indicates the battery is charged complete ly. (The battery shall be charged fully within three hours depending on how much power left in it.)(4) When the battery is completely charged, you can remove the Child unit from the Charger.
7Setting Up3. How to use the belt(1) Put the Child unit on the wrist as illustrated. (2) Wind the end of the belt without the clasp around your wrist and thread the clip on the inside. And then adjust the belt to the right tension. (3)Clicktheclasptoxthelengthofthebelt.(4)Foldupthetailofthebeltandstickitonthexedbelt.1 2 3 4OK
8Setting UpSet up the Parent Unit1.Open the battery cover in the direction as illustrated. 2.Install two AAA alkaline batteries in the battery cave in the right direction based on its pole. 3.Close the battery cover on the Parent unit. 4.Turn the OFF switch of the Parent unit to any distance of the warning range: near, normal or far. At this moment, the Power LED will light red. 5. You can wear the Parent unit on your waist. 1 2 3 4
9Setting UpCheck the connectionWhen the Parent unit and the Child unit are interconnected, the channel 1 indicator lightingredandthedirectionindicatorashingbluesuggesttheconnectioniscorrect. OKchannel 1 LED
10Using the Child TrackerPlease do not put the Child unit in the pocket when you use it. Please wear the Child unit on your child’s wrist to get the best direction indication. When the Parent unit is searching the Child unit, please hold the Parent unit tightly in a horizontal position to get the best direction indication.
11Using the Child TrackerThe Parent Unit can be connected up to 4 Child unitsa. When you only have one Child unit:If the Parent unit is corresponding to only one Child unit, the Child unit and the Parent unit will be set as channel 1 internally. When the Child unit is within the warning range of the Parent unit, the channel 1 LED will light red. When the Child unit is out of the warning range of the Parent unit, the channel 1LEDwillashredandthebuzzerwillbeep.Atthemoment,youcanpresschannelselectionbuttonorndbuttontoturnoffthebuzzer.Becausethere’s only one Child unit, when you press channel selection button the channel won’t be switched.1 2channel 1 LEDBeBechannel 1 LEDChannel selection function
12Using the Child Trackerchannel 1 LEDBeBeBechannel 3 LED35mb. When there are several Child units: If the Parent unit is corresponding to several Child units, you can press channel selection button to select the Child unit you want to monitor. When the selected Child unit is within the warning range, the channel LED will light red. When the selected Child unitisoutofthewarningrange,thechannelLEDwillashred.OtherchannelLEDsoftheParentunitcorrespondingtoconguredChildunitswilllightgreenwhenthe Child units are within the warning range. When the Child units are out of the warningrangebutwithinthemonitoringrange,theLEDwillashgreen.WhentheChild units are out of valid monitoring range, the channel LED will go out.
13Using the Child TrackerAdding Child unitsWhen you want to add more Child units to the Parent unit, hold both the Find button /initiation child unit button of the Parent unit and the desired Find button/ initiation child unit button of the Child unit for 8 seconds. Then the buzzers of both Parent and Child units will beep to inform you the Child unit is added. The channel of newly added Child unit will automatically be set at the lowest channel that hasn’t been set. Removing Child unitsWhen you want to remove any Child units from the Parent unit, please hold the channel selection button/deletion child unit button for 8 seconds. Then the buzzer of the Parent unit will beep to inform you the Child unit is removed. Please note that when you complete removing, the Child unit and the Parent unit can not be connected. If you want to connect them, please repeat the steps described in Adding Child Units. to connect them, please repeat the steps described in Adding Child Units. Bechannel 2 LEDBechannel 2 LED
14Using the Child Trackera. Parent unit:Whenthebatterypowerislow,thePowerLEDwillashredasawarning,pleasereplace with new batteries.b. Child Unit:Whenthebatterypowerislow,thePowerLEDwillashredasawarning,pleaseputthe Child unit in the charger to charge the battery. It is recommended that the batteries shall be removed to extend the battery life when not used. Battery low indicatorDirectional indicator functionThere are 6 blue LED indicators on the Parent unit as shown in thegure.WhenthreeoftheLEDsareashingatthesametime,it suggests that the Child unit is in this direction with an angle of 120 degrees. When only one of the LEDs is ashing, it suggeststhat the Child unit is in this direction with an angle of 60 degrees. When all the 6 LEDs go off, it suggests that the Child unit is out of the monitoring range. In this case, the Channel indicator becomes red.1 52 436
15Using the Child Tracker1 52 436a1 2 62 3 4c2 3 4e32 44 5 6b21 3d3 4 5f1 5 6a1 2 62 3 4c2 3 4e32 44 5 6b21 3d3 4 5f1 5 6a. When Indicator 1ashesorIndicator1, 2 and 6ashatthesametime,itindicatesthemonitoredChildunitsis in the relative position of the left-half of the Parent unit. At this moment, please stay where you are and hold the Parent unit. Then turn counterclockwise until LED 2, 3 or 4 lights up. b. When Indicator 2ashesorIndicator1, 2 and 3ashatthesametime,itindicatesthemonitoredChildunitsis in the relative position of the front left of the Parent unit. At this moment, please hold the Parent unit and move toward front-left to search for the Child unit. c. When Indicator 3ashesorIndicator 2, 3 and 4ashatthesametime,itindicatesthemonitoredChildunitsis in the relative position of the front of the Parent unit. At this moment, please hold the Parent unit and move forward to search for the Child unit.d. When Indicator 4ashesorIndicator3, 4 and 5ashinthesametime,itindicatesthattheChildunitsbeing monitored is in the relative position of the front right of the Parent unit. In the meantime, please hold the Parent unit and move front-right to search for the Child unit.e. When Indicator 5ashesorIndicator4, 5 and 6ashatthesametime,itindicatesthemonitoredChildunitsis in the relative position of the right-half of the Parent unit. At this moment, please stay where you are and hold the Parent unit. Then turn clockwise until LED 2, 3 or 4 lights up. f. When Indicator 6ashesorIndicator 1, 5 and 6ashatthesametime,itindicatesthemonitoredChildunits is in the relative position of the back of the Parent unit. At this moment, please hold the Parent unit and turn 180 degree.Note: The LEDs will be ashing quicker when the Parent unit is getting closer to the Child unit. Meanwhile, when the Parent unit is getting further away from the Child unit, the LEDs will be ashing slower.
16There is a Power and Warning Range (Far, Normal and Near) switch on the lateral side of the Parent unit. When the switch is turned to ), it indicates the warning range is set at 5~10m. When the switch is turned to )), it’s 8~20m. When the switch is turned to ))), it indicates the warning range is set at the farthest, i.e. 15~30m. The user can set the distance of the warning range based on the environment and re-quirement. When the distance between the Child unit and the Parent unit is within the warning range, the channel LED will light red or green. When the distance between the Child unit and the Parent unit is out of the warning range, the channel LED willashredorgreenandthebuzzeroftheParentunitwillbeepasawarning.Atthismo-ment, you can press Find button or channel selection button Using the Child Tracker) 5~10m) )8~20m) ) )15~30mchannel 3 LEDBeBeBechannel 1 LED35mto turn off the buzzer. Then press channel selection button again to select the desired channel of the direction to monitor. Warning range setup
17Using the Child Trackera. How to use the Parent unit to call the Child unit:When you use the Parent unit to search for the Child unit, in addition to the directional LED indicators, you can also do so by pressing the Find button. When you press the Find button, the buzzers in the Child and Parent units will beep. You canalsondtheChildunitbyfollowingthebeepsound.The beep sound will become quicker if the Parent unit is getting closer to the Child unit. Meanwhile, when the Parent unit is getting further away from the Child unit, the beep sound will become slower. You can turn off the buzzers on the Child and Parent units by pressing the Find button again on the Parent unit.BeBeBechannel 1 LEDchannel 1 LEDWarning range setup Find function
18Using the Child Trackerb. How to use the Child unit to call the Parent unit:The user can also use the Child unit to call the Parent unit actively. When the Find button on the Child unit is pressed, the buzzer on the Parent unit will beep as a warning. At this moment, if the Find button or channel selection button on the Parent unit is pressed, the buzzer will turn off. BeBeBeBeBeBe
19FeaturesBothunitsfullyportablewithupto50mrange.LEDs to guide the parent to the child nistantly.Each parent unit is capable of monitoring 4 separate child units.When the ParentunitisgettingclosertotheChildunit,theLEDswillbeashingquickerandthe beep sound will become quicker.Setting warning range - You can set distance between Child Unit and Parent Unit (Near range / Normal range / Far range).The user can use the Child unit to call the Parent unit actively.Lowpowerdetection-Whenthebatterypowerislow,thepowerLEDwillashredasawarning.
20TroubleshootingIf you are not getting any signal at all Please check if you turn on the power switch on the Parent unit. Please check if the power LED on the Parent unit lights red. If not, please check whether the batteries are installed in the right direction. If the batteries installed in the Parent unit are in the right direction, please replace with new batteries. Please check if the power LED on the Child unit lights red. If not, please check whether the batteries are installed in the right direction.If the batteries installed in the Child unit are in the right direction, please put the Child unit on the charger to charge the battery. If the power LED of both the Child unit and Parent unit light red but the channel LED is not lit, please add Child units by following the procedures described above. There’s something wrong with the direction indicationPlease make sure that the child wears the Child unit on his or her wrist to get the best direction indication. Please make sure that when you use the Parent unit to search the direction of the Child unit, you have held the Parent unit tightly in a horizontal position to get the best direction indication. The direction indication may be slightly inaccurate if the user uses this product in a smaller and enclosed room. It is ideal for uses in public places, such as parks or shopping malls.
21Technical Specification/Care and maintenanceSystemRadio Frequency 2477.5 to 2482.5 MHz, Direct Sequence Spread SpectrumOperating Range Typical 50 meters/150 feet light of sightWarning Range 5 to 30 meters/15 to 90 feetParent UnitPower Supply 2 x AAA 1.5V non rechargeable alkaline batteriesDimension W:45mm H:45mm D:11.5mmWeight 50gOperating temperature 0 C ~ 40 C (32 F ~ 104 F )Child UnitPower Supply 1 x AC power adapter DC 6V 200 mA 1 x LIR2450 Li+ 3.6V rechargeable batteryDimension W:45mm H:110mm D:140mmWeight 34gOperating temperature 0 C ~ 40 C (32 F ~ 104 F )Care and maintenance Remove batteries from the unit if you do not plan to use it for a period of time. Dispose of used batteries in an environmentally friendly manner. Cleanthechildnderwithadumpcloth.Specicationsaresubjecttochangewithoutnotice.Technical Specication
Ce Que Vous ObtenezLégende des fonctionsInformations importantesInstallation Installation de l’Unité Enfant Installer l’Unité Parents Contrôlez la connexionUtilisation du Traqueur Enfant Fonction de choix des Canaux Ajouter des Unités Enfant Retirer des Unités Enfant Indicateur de faibles batteries Indicateur de Fonction directionnelle Installation de l’Avertissement de Fonction de TrouverCaractéristiquesDépannage ............................23...........................24.......................26...............................................27................................................................273031................32.............33.......................35........................35..............36...36..........38..............................39.....................................41............................................42
23FRANCAISUnité Parents Unité Enfant Chargeur d’Unité Enfant Prise d’Adaptateur de chargeur d’Unité Enfant Batterie rechargeable LIR2450 Li+ 3.6V pour l’Unité Enfant 2 piles alcalines non rechargeables AAA 1.5V pour l’Unité Parent Manuel UtilisateurCe Que Vous Obtenez.......................................................
24Légende des fonctions134526789212356478910A, Unité Parent Fig. 1 B, Unité Enfant Fig. 2Fig. 1
25FRANCAISLégende des fonctionsBouton trouver Bouton d’initiation Unité EnfantIndicateur de direction LEDIndicateur de Canal LEDBouton de sélection de Canal/bouton efface Unité EnfantHaut parleurPuissance/indicateur de batterie de faible puissance Arrêt puissance/signal de proximité près/normal/Attache de ceinturecouvercle de batteriescapteur de chargecouvercle de batteriesAttachePuissance/indicateur de batterie haut ParleurBouton de trouver/boutonCapteur du ChargeurIndicateur de chargeur LEDfiche de prise d’adaptateurPrise d’adaptateur du ChargeurA, Parent Unit Fig. 112345678912345678910A, Unité Parent Fig. 1 B, Unité Enfant Fig. 2LEDde faible puissance LEDd’invitation Unité Enfant
26Informations importantes1. Si vous voyagez à l’étranger, assurez-vous que la tension montrée sur la prise de l’adaptateur correspond à la puissance de forces locale avant le raccordement à l’alimentation d’énergie.2. Pour empêcher toute décharge électrique, n’ouvrez pas le boitier de l’Unité Enfant et de l’Unité Parent (à part les couvercles des compartiments batteries)3. Pour prévenir tout risque d’explosion n’utilisez pas de batteries d’un type incor rect. Pour l’Unité Enfant, utilisez toujours la batterie rechargeable LIR2450 de 3.6V Li+. Pour l’Unité Parent, nous recommandons des piles alcalines non recharge ables de 1.5V AAA.
27FRANCAISInstallationInstallation de l’Unité Enfant Quand vous employez ce produit pour la première fois, veuillez le mettre en charge.1. Comment installer les batteries(1) insérez les deux barrettes de ceinture dans le couvercle de batterie au le dos de l’Unité Enfant et puis ouvrez le couvercle de batterie en le tournant dans le sens contraire des aiguilles d’une montre. (2) Installez la batterie LIR2450 dans le couvercle de batterie et tournez les barrettes de ceinture dans le sens des aiguilles d’une montre pour combiner le couvercle de batterie avec l’Unité Enfant. (Veuillez notez les pôles +/- en installant la batterie.) A ce moment, la lumière LED rouge de puissance s’allume.
28Installation2. Comment chargerOK1 2 3 4(1) Insérez l’Adaptateur de Chargeur dans la prise électrique. (2)Branchezl’AdaptateurdeChargeurauChargeur.L’indicateurdechargeur  clignotera rouge et vert trois fois respectivement et puis s’éteindra. (3) Reliez l’Unité Enfant au Chargeur comme illustré, et l’indicateur de Charge passera au rouge pour indiquer qu’il est en Charge. Quand les voyants l’indicateur de Charge passe au vert, cela indique que la batterie est chargée complètement. (La batterie sera chargée entièrement dans un délai de suivant le degré de charge restant dans la batterie.)(4) Lorsque la batterie est complètement chargée, vous pouvez débrancher l’Unité Enfant du chargeur.
29FRANCAISInstallation3. Comment utiliser la ceinture(1) Mettez l’Unité Enfant sur le poignet comme illustré. (2) Enroulez l’extrémité de la ceinture sans l’attache autour de votre poignet et enlezlesbarrettes à l’intérieur. Et ajustez alors la ceinture sur à la bonne tension. (3)Cliquezl’attachepourxerlalongueurdelaceinture.(4)Pliezlaqueuedelaceintureetcollez-lasurlaceinturexe.1 2 3 4OK
30InstallationInstaller l’Unité Parents1. Ouvrez le couvercle des piles dans la direction suivant l’illustration. 2. Installez les deux piles alcalines AAA. dans l’emplacement des piles dans la bonne direction basée sur les pôles +/-. 3. Fermez le couvercle des piles sur l’Unité Parents. 4. Tournez le commutateur de l’Unité Parents à n’importe quelle distance de la gamme d’avertissement : près, normale ou loin. Alors, la lumière LED rouge de la puissance s’allume. 5. Vous pouvez porter l’Unité Parents à votre taille.1 2 3 4
31FRANCAISInstallationContrôlez la connexion Lorsque l’Unité Parents et l’Unité Enfant sont interconnectés, l’indicateur du canal 1 s’allumera en rouge, et l’indicateur de direction clignotera en bleu, ce qui indique que la connexion est correcte. OKchannel 1 LED
32Utilisation du Traqueur EnfantVeuillez ne pas mettre l’Unité Enfant dans sa poche quand vous l’employez. Veuillez passer l’Unité Enfant sur le poignet de votre enfant pour obtenir une meilleure indication de direction. Quand l’Unité Parents trouver l’Unité Enfant, tenez svp l’Unité Parents étroitement en position horizontale pour obtenir une meilleure indication de direction.
33FRANCAISUtilisation du Traqueur EnfantFonction de choix des CanauxL’Unité Parents peut être reliée jusqu’à 4 Unités Enfanta. Quand vous avez seulement une Unité Enfant :1 2channel 1 LEDBeBechannel 1 LEDSi l’Unité Parents ne correspond qu’à une Unité Enfant, l’Unité Enfant et l’Unité Parents seront placées sur le canal 1 intérieure. Quand l’Unité Enfant est dans la marge d’avertissement de l’Unité Parents, la LED du canal 1 s’allumera en rouge. Quand l’Unité Enfant est hors de la gamme d’avertissement de l’Unité Parents, le LED du canal 1 clignotera rouge et le bipper fera bip-bip. Vous pouvez alors appuyer sur le bouton de choix de canal ou le bouton de recherche pour arrêter le bipper. Puisqu’il n’y a seulement qu’une unité d’enfant, quand vous appuyer sur le choix de canal, le canal ne sera pas commuté.
34Utilisation du Traqueur Enfantchannel 1 LEDBeBeBechannel 3 LED35mb. Quand il y a plusieurs Unités Enfant : Si l’Unité Parent correspond à plusieurs l’Unités Enfant, vous pouvez appuyer sur le bouton de choix de canal pour choisir l’Unité Enfant que vous voulez surveiller. Quand l’Unité Enfant choisie est dans la marge d’avertissement, le LED rouge du canal, s’allumera. Quand l’unité choisie d’enfant est hors de la gamme d’avertissement, le LED du canal clignotera en rouge. Les autres LED des canaux de l’Unité Parents correspondantauxl’UnitéEnfantconguréess’allumerontenvertquandlesUnitésEnfant sont dans la marge d’avertissement. Quand les Unité Enfant sont hors de la gamme d’avertissement mais dans la marge de surveillance, le LED vert clignotera. Quand les unités d’enfant sont hors de gamme de surveillance valide, le canal LED s’éteindra.
35FRANCAISUtilisation du Traqueur EnfantAjouter des Unités EnfantQuand vous voulez ajouter plus d’Unité Enfant à l’Unité Parents, re-tenez les boutons Trouver/initiation Unité enfant de l’Unité Parents et le bouton désiré de Trouver de l’Unité Enfant pendant dix secondes. Puis les bippers des Unités Parents et Enfant feront bip-bip pour vous informer que l’Unité Enfant est ajoutée. Le canal de la nouvelle Unité Enfant supplémentaire sera automatiquement placé sur le canal le plus bas restant.Retirer des Unités EnfantQuand vous voulez retirer une des Unité Enfant à partir de l’Unité Par-ents, retenez svp le bouton de choix de canal/effacement Unité en-fant pendant dix secondes. Alors le bipper de l’unité de parents fera bip-bip pour vous informer que l’Unité Enfant est enlevée. Veuillez noter quand vous retirer complètement, l’Unité Enfant et l’Unité Par-ents ne peuvent pas être connectées. Si vous voulez les relier, répétez svp les étapes décrivant l’ajout d’Unités d’enfant.Bechannel 2 LEDBechannel 2 LED

Navigation menu