Tranwo Technology TTD-80R Wireless digital child tracker User Manual Manual P1

Download:
Mirror Download [FCC.gov]
Document ID	736296
Application ID	cT0zAGxeOO8M7VmGnOZo7w==
Document Description	Manual P1
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	249.7kB (3121260 bits)
Date Submitted	2006-12-08 00:00:00
Date Available	2006-12-08 00:00:00
Creation Date	2006-12-08 13:52:04
Producing Software	Adobe PDF Library 7.0
Document Lastmod	2006-12-08 13:54:10
Document Title	Manual P1
Document Creator	Adobe InDesign CS2 (4.0)

What You Get ......................................... 1
Product Layout ........................................ 2
Important Information............................. 4
Setting Up ................................................ 5
Set up the Child Unit ...........................5
Set up the Parent Unit ...........................8
Check the connection...........................9
Using the Child Tracker ...........................10
Channel selection function ................... 11
Adding Child units ................................. 13
Removing Child units ............................ 13
Battery low indicator ............................. 14
Directional indicator function ................ 14
Warning range setup ............................. 16
Find function ......................................... 17
Features .................................................. 19
Troubleshooting ...................................... 20
Technical Specification .......................... 21
Care and maintenance.......................... 21
What You Get
Parent Unit
Child Unit
Child Unit charger
Child Unit charger main power adapter
LIR2450 Li+ 3.6V rechargeable battery for Child Unit
2 x AAA 1.5V non rechargeable alkaline batteries for Parent Unit
User’s Manual
Produc t Layout
A, Parent Unit Fig. 1
B, Chid Unit Fig. 2
10
What You Get
A, Parent Unit Fig. 1
B, Chid Unit Fig. 2
Find button/Initiation child unit button
charge sensor
Directional indicator LED
Battery cover
Channel indicator LED
Clasp
Channel selection button/Deletion child unit button
Power/battery low indicator LED
Speaker
Speaker
Power/battery low indicator LED
Find button/lnitiation child unit button
Power off/warning range  switch
Charger sensor
Belt clip
Charger indicator LED
battery cover
power adapter jack
10
Charger main power adapter
Impor tant Information
1. If traveling abroad, make sure that the voltage shown on the mains power
adapter corresponds to the local mains power before connection to the
power supply.
2. To prevent electric shock, do not open the case of the Child Unit and Parent
Unit (except battery covers)
3. Risk of explosion if batteries are replaced by an incorrect type. For the Child
Unit, always use LIR2450 3.6V Li+ rechargeable battery. For the Parent 		
Unit, suggestion use AAA non rechargeable 1.5V alkaline batteries.
Setting Up
Set up the Child Unit
When you use this product for the first time, please charge it.
1. How to install the batteries
(1)Insert the two belt clips into the battery cover on the back of the Child unit and then
open the battery cover by turning it counterclockwise.
(2) Install the LIR2450 battery into the battery cover and turn the belt clips clockwise to
combine the battery cover with the Child unit. (Please note the poles when installing
batteries.) In the meantime, the Power LED will light red.
Setting Up
2.How to charge
(1) Insert the Charger Adapter into the power socket.
(2) Connect the Charger Adapter with the Charger. In the meantime, the Charger
indicator will flash red and green for three times respectively and then go out.
(3) Connect the Child unit to the Charger in the direction as illustrated, and the 		
Charger indicator will light red to indicate that it is being charged. When 		
the Charger indicator lights green, it indicates the battery is charged complete		
ly. (The battery shall be charged fully within three hours depending on how 		
much power left in it.)
(4) When the battery is completely charged, you can remove the Child unit from 		
the Charger.
OK
Setting Up
3. How to use the belt
(1) Put the Child unit on the wrist as illustrated.
(2) Wind the end of the belt without the clasp around your wrist and thread the clip
on the inside. And then adjust the belt to the right tension.
(3) Click the clasp to fix the length of the belt.
(4) Fold up the tail of the belt and stick it on the fixed belt.
OK
Setting Up
Set up the Parent Unit
1.Open the battery cover in the direction as illustrated.
2.Install two AAA alkaline batteries in the battery cave in the
right direction based on its pole.
3.Close the battery cover on the Parent unit.
4.Turn the OFF switch of the Parent unit to any distance of the warning 			
range: near, normal or far. At this moment, the Power LED will light red.
5. You can wear the Parent unit on your waist.
Setting Up
Check the connection
When the Parent unit and the Child unit are interconnected, the channel 1 indicator
lighting red and the direction indicator flashing blue suggest the connection is correct.
OK
channel
LED
Using the Child Tracker
Please do not put the Child unit in the pocket when you use it. Please wear the Child
unit on your child’s wrist to get the best direction indication. When the Parent unit is
searching the Child unit, please hold the Parent unit tightly in a horizontal position to get
the best direction indication.
10
Using the Child Tracker
channel
Be
LED
channel
Be
LED
Channel selec tion func tion
The Parent Unit can be connected up to 4 Child units
a. When you only have one Child unit:
If the Parent unit is corresponding to only one Child unit, the Child unit and the Parent
unit will be set as channel 1 internally. When the Child unit is within the warning range of
the Parent unit, the channel 1 LED will light red. When the Child unit is out of the warning
range of the Parent unit, the channel 1 LED will flash red and the buzzer will beep.At the
moment, you can press channel selection button or find button to turn off the buzzer. Because
there’s only one Child unit, when you press channel selection button the channel won’t
be switched.
11
Using the Child Tracker
BB
Be
35
channel
LED
channel
b. When there are several Child units:
LED
If the Parent unit is corresponding to several Child units, you can press channel selection
button to select the Child unit you want to monitor. When the selected Child unit is
within the warning range, the channel LED will light red. When the selected Child
unit is out of the warning range, the channel LED will flash red. Other channel LEDs
of the Parent unit corresponding to configured Child units will light green when
the Child units are within the warning range. When the Child units are out of the
warning range but within the monitoring range, the LED will flash green. When the
Child units are out of valid monitoring range, the channel LED will go out.
12
Using the Child Tracker
Adding Child units
When you want to add more Child units to the Parent unit, hold both
the Find button /initiation child unit button of the Parent unit and the
desired Find button/ initiation child unit button of the Child unit for 8
seconds. Then the buzzers of both Parent and Child units will beep
to inform you the Child unit is added. The channel of newly added
Child unit will automatically be set at the lowest channel that hasn’t
been set.
Be
channel
LED
Removing Child units
When you want to remove any Child units from the Parent unit, please
hold the channel selection button/deletion child unit button for 8 seconds.
Then the buzzer of the Parent unit will beep to inform you the Child
unit is removed. Please note that when you complete removing, the
Child unit and the Parent unit can not be connected. If you want to
connect them, please repeat the steps described in Adding Child
Units. to connect them, please repeat the steps described in Adding
Be
channel
LED
Child Units.
13
Using the Child Tracker
Batter y low indicator
a. Parent unit:
When the battery power is low, the Power LED will flash red as a warning, please
replace with new batteries.
b. Child Unit:
When the battery power is low, the Power LED will flash red as a warning, please put
the Child unit in the charger to charge the battery. It is recommended that the batteries
shall be removed to extend the battery life when not used.
Direc tional indicator func tion
There are 6 blue LED indicators on the Parent unit as shown in
the figure. When three of the LEDs are flashing at the same time,
it suggests that the Child unit is in this direction with an angle of
120 degrees. When only one of the LEDs is flashing, it suggests
that the Child unit is in this direction with an angle of 60 degrees.
When all the 6 LEDs go off, it suggests that the Child unit is out of
the monitoring range. In this case, the Channel indicator becomes
red.
14
a
1 2
2 3 4
2 3 4
1 2 3
Using the Child Tracker
1 2
2 3 4
4 5 6
2 3 4
1 2 3
3 4 5
23 4
5 6
a. When Indicator 1 flashes or Indicator 1, 2 and 6 flash at the same time, it indicates the monitored Child units is
in
d the relative position
e of the left-half of
f the Parent unit. At this moment, please stay where you are and
hold the Parent unit. Then turn
counterclockwise until LED 2, 3 or 4 lights up.
4 5 6
b. When Indicator 2 flashes or Indicator 1, 2 and 3 flash at the same time, it indicates the monitored Child units is
in the relative position of the front left of the Parent unit. At this moment, please hold the Parent unit and
move toward front-left to search for the Child unit.
c. When Indicator 3 flashes or Indicator 2, 3 and 4 flash at the same time, it indicates the monitored Child units is
in the relative position of the front of the Parent unit. At this moment, please hold the Parent unit and
5 6
move forward
to search for2 the
Child unit.
3 4 5
3 4
d. When Indicator 4 flashes or Indicator 3, 4 and 5 flash in the same time, it indicates that the Child units being
monitored is in the relative position of the front right of the Parent unit. In the meantime, please hold the Parent
unit and move front-right to search for the Child unit.
e. When Indicator 5 flashes or Indicator 4, 5 and 6 flash at the same time, it indicates the monitored Child units is
in the relative position of the right-half of the Parent unit. At this moment, please stay where you are and
hold the Parent unit. Then turn clockwise until LED 2, 3 or 4 lights up.
f. When Indicator 6 flashes or Indicator 1, 5 and 6 flash at the same time, it indicates the monitored Child units
is in the relative position of the back of the Parent unit. At this moment, please hold the Parent unit and turn
180 degree.
Note: The LEDs will be flashing quicker when the Parent unit is getting closer to the Child unit. Meanwhile, when the Parent unit is getting further
away from the Child unit, the LEDs will be flashing slower.
15
Using the Child Tracker
5~10m ))
8~20m
))) 15~30m
Warning range setup
There is a Power and Warning Range (Far, Normal and Near) switch
on the lateral side of the Parent unit. When the switch is turned to
), it indicates the warning range is set at 5~10m. When the switch is
turned to )), it’s 8~20m. When the switch is turned to ))), it indicates
the warning range is set at the farthest, i.e. 15~30m. The user can set
the distance of the warning range based on the environment and requirement. When the distance between the Child unit and the Parent unit
is within the warning range, the channel LED will light red or green. When the distance
between the Child unit and the Parent unit is out of the warning range, the channel LED
will flash red or green and the buzzer of the Parent unit will beep as a warning. At this moment, you can press Find button
or channel selection button
to turn off the buzzer. Then press
channel selection button again
35
to select the desired channel
of the direction to monitor.
channel
LED
channel
16
LED
Using the Child Tracker
Find func tion
a. How to use the Parent unit to call the Child unit:
When you use the Parent unit to search for the Child unit, in addition to the directional
LED indicators, you can also do so by pressing the Find button.
When you press the Find button, the buzzers in the Child and Parent units will beep. You
can also find the Child unit by following the beep sound.
The beep sound will become quicker if the Parent unit is getting closer to the Child unit.
Meanwhile, when the Parent unit is getting further away from the Child unit, the beep
sound will become slower.
You can turn off the buzzers on the Child and Parent units by pressing the Find button
Be
again on the Parent unit.
Be
Be
channel
LED
channel
LED
17
Using the Child Tracker
b. How to use the Child unit to call the Parent unit:
The user can also use the Child unit to call the Parent unit actively. When the Find
button on the Child unit is pressed, the buzzer on the Parent unit will beep as a warning.
At this moment, if the Find button or channel selection button on the Parent unit is
pressed, the buzzer will turn off.
Be
Be B
18
Be
Be B
Features
Both units fully portable with up to 50m range.
LEDs to guide the parent to the child nistantly.
Each parent unit is capable of monitoring 4 separate child units.
When the Parent unit is getting closer to the Child unit, theLEDs will be flashing quicker and
the beep sound will become quicker.
Setting warning range - You can set distance between Child Unit and Parent Unit (Near
range / Normal range / Far range).
The user can use the Child unit to call the Parent unit actively.
Low power detection - When the battery power is low, the power LED will flash red as a
warning.
19
Troubleshooting
If you are not getting any signal at all
Please check if you turn on the power switch on the Parent unit.
Please check if the power LED on the Parent unit lights red. If not, please check whether the
batteries are installed in the right direction.
If the batteries installed in the Parent unit are in the right direction, please replace with new
batteries.
Please check if the power LED on the Child unit lights red. If not, please check whether the
batteries are installed in the right direction.
If the batteries installed in the Child unit are in the right direction, please put the Child unit on
the charger to charge the battery.
If the power LED of both the Child unit and Parent unit light red but the channel LED is not lit,
please add Child units by following the procedures described above.
There’s something wrong with the direction indication
Please make sure that the child wears the Child unit on his or her wrist to get the best direction
indication.
Please make sure that when you use the Parent unit to search the direction of the Child unit,
you have held the Parent unit tightly in a horizontal position to get the best direction indication.
The direction indication may be slightly inaccurate if the user uses this product in a smaller and
enclosed room. It is ideal for uses in public places, such as parks or shopping malls.
20
Technical Specification/ Care and maintenance
Technical Specification
System
Radio Frequency
Operating Range Typical
2477.5 to 2482.5 MHz, Direct Sequence Spread Spectrum
50 meters/150 feet light of sight
Warning Range
5 to 30 meters/15 to 90 feet
Parent Unit
Power Supply
Dimension
Weight
Operating temperature
Child Unit
2 x AAA 1.5V non rechargeable alkaline batteries
W:45mm H:45mm D:11.5mm
50g
0 C ~ 40 C (32 F ~ 104 F )
Power Supply
1 x AC power adapter DC 6V 200 mA
1 x LIR2450 Li+ 3.6V rechargeable battery
Dimension
Weight
Operating temperature
W:45mm H:110mm D:140mm
34g
0 C ~ 40 C (32 F ~ 104 F )
Specifications are subject to change without notice.
Care and maintenance
Remove batteries from the unit if you do not plan to use it for a period of time.
Dispose of used batteries in an environmentally friendly manner.
Clean the child finder with a dump cloth.
21
Ce Que Vous Obtenez ............................23
Légende des fonctions ........................... 24
Informations importantes ....................... 26
Installation ............................................... 27
Installation de l ’Unité Enfant ............. 27
Installer l’Unité Parents ......................... 30
Contrôlez la connexion .......................... 31
Utilisation du Traqueur Enfant ................
		 32
Fonction de choix des Canaux ............. 33
Ajouter des Unités Enfant ....................... 35
Retirer des Unités Enfant ........................ 35
Indicateur de faibles batteries .............. 36
Indicateur de Fonction directionnelle ... 36
Installation de l’Avertissement de ..........
		 38
Fonction de Trouver .............................. 39
Caractéristiques ..................................... 41
Dépannage ............................................ 42
Ce Q ue Vous Obtenez
FRANCAIS
Unité Parents
Unité Enfant
Chargeur d’Unité Enfant
Prise d’Adaptateur de chargeur d’Unité Enfant
Batterie rechargeable LIR2450 Li+ 3.6V pour l’Unité Enfant
2 piles alcalines non rechargeables AAA 1.5V pour l’Unité Parent
Manuel Utilisateur
23
Fig. 1
Légende des fonc tions
A, Unité Parent Fig. 1
B, Unité Enfant Fig. 2
10
24
Légende des fonc tions
FRANCAIS
Fig.11
A, Unité
ParentParent
Unit Fig.
B, Unité Enfant Fig. 2
Bouton trouver Bouton d’initiation Unité Enfant
capteur de charge
Indicateur de direction LED
couvercle de batteries
Indicateur de Canal LED
Attache
Bouton de sélection de Canal/bouton efface Unité Enfant
Haut parleur
Puissance/indicateur de batterie
de faible puissance LED
haut Parleur
Puissance/indicateur de batterie de faible puissance
LED
Bouton de trouver/bouton
d’invitation Unité Enfant
Arrêt puissance/signal de proximité près/normal/
Capteur du Chargeur
Attache de ceinture
Indicateur de chargeur LED
couvercle de batteries
fiche de prise d’adaptateur
10
Prise d’adaptateur du Chargeur
25
Informations impor tantes
1. Si vous voyagez à l’étranger, assurez-vous que la tension montrée sur la prise de
l’adaptateur correspond à la puissance de forces locale avant le raccordement
à l’alimentation d’énergie.
2. Pour empêcher toute décharge électrique, n’ouvrez pas le boitier de l’Unité
Enfant et de l’Unité Parent (à part les couvercles des compartiments batteries)
3. Pour prévenir tout risque d’explosion n’utilisez pas de batteries d’un type incor
rect. Pour l’Unité Enfant, utilisez toujours la batterie rechargeable LIR2450 de 3.6V
Li+. Pour l’Unité Parent, nous recommandons des piles alcalines non recharge
ables de 1.5V AAA.
26
Installation
Quand vous employez ce produit pour la première fois, veuillez le mettre en charge.
1. Comment installer les batteries
(1) insérez les deux barrettes de ceinture dans le couvercle de batterie au le dos de l’Unité
Enfant et puis ouvrez le couvercle de batterie en le tournant dans le sens contraire des
aiguilles d’une montre.
(2)		Installez la batterie LIR2450 dans le couvercle de batterie et tournez les barrettes de
ceinture dans le sens des aiguilles d’une montre pour combiner le couvercle de batterie
avec l’Unité Enfant. (Veuillez notez les pôles +/- en installant la batterie.) A ce moment,
la lumière LED rouge de puissance s’allume.
27
FRANCAIS
Installation de l’Unité Enfant
Installation
2. Comment charger
(1) Insérez l’Adaptateur de Chargeur dans la prise électrique.
(2) Branchez l’Adaptateur de Chargeur au Chargeur. L’indicateur de chargeur
clignotera rouge et vert trois fois respectivement et puis s’éteindra.
(3) Reliez l’Unité Enfant au Chargeur comme illustré, et l’indicateur de Charge 		
passera au rouge pour indiquer qu’il est en Charge. Quand les voyants 		
l’indicateur de Charge passe au vert, cela indique que la batterie est chargée
complètement. (La batterie sera chargée entièrement dans un délai de suivant
le degré de charge restant dans la batterie.)
(4) Lorsque la batterie est complètement chargée, vous pouvez débrancher l’Unité
Enfant du chargeur.
OK
28
Installation
FRANCAIS
3. Comment utiliser la ceinture
(1) Mettez l’Unité Enfant sur le poignet comme illustré.
(2) Enroulez l’extrémité de la ceinture sans l’attache autour de votre poignet et enfilez les
barrettes à l’intérieur. Et ajustez alors la ceinture sur à la bonne tension.
(3) Cliquez l’attache pour fixer la longueur de la ceinture.
(4) Pliez la queue de la ceinture et collez-la sur la ceinture fixe.
OK
29
Installation
Installer l’Unité Parents
1. Ouvrez le couvercle des piles dans la direction suivant
l’illustration.
2. Installez les deux piles alcalines AAA. dans l’emplacement
des piles dans la bonne direction basée sur les pôles +/-.
3. Fermez le couvercle des piles sur l’Unité Parents.
4. Tournez le commutateur de l’Unité P a r e n t s à n ’ i m p o r t e q u e l l e d i s t a n c e
de la gamme d’avertissement : près, normale ou loin. Alors, la lumière LED rouge
de la puissance s’allume.
5. Vous pouvez porter l’Unité Parents à votre taille.
30
Installation
FRANCAIS
Contrôlez la connexion
Lorsque l’Unité Parents et l’Unité Enfant sont interconnectés, l’indicateur du canal 1
s’allumera en rouge, et l’indicateur de direction clignotera en bleu, ce qui indique que
la connexion est correcte.
OK
channel
LED
31
Utilisation du Traqueur Enfant
Veuillez ne pas mettre l’Unité Enfant dans sa poche quand vous l’employez. Veuillez
passer l’Unité Enfant sur le poignet de votre enfant pour obtenir une meilleure indication de
direction. Quand l’Unité Parents trouver l’Unité Enfant, tenez svp l’Unité Parents étroitement
en position horizontale pour obtenir une meilleure indication de direction.
32
Utilisation du Traqueur Enfant
channel
Be
LED
channel
FRANCAIS
Be
LED
Fonction de choix des Canaux
L’Unité Parents peut être reliée jusqu’à 4 Unités Enfant
a. Quand vous avez seulement une Unité Enfant :
Si l’Unité Parents ne correspond qu’à une Unité Enfant, l’Unité Enfant et l’Unité Parents seront
placées sur le canal 1 intérieure. Quand l’Unité Enfant est dans la marge d’avertissement
de l’Unité Parents, la LED du canal 1 s’allumera en rouge. Quand l’Unité Enfant est hors
de la gamme d’avertissement de l’Unité Parents, le LED du canal 1 clignotera rouge et
le bipper fera bip-bip. Vous pouvez alors appuyer sur le bouton de choix de canal ou
le bouton de recherche pour arrêter le bipper. Puisqu’il n’y a seulement qu’une unité
d’enfant, quand vous appuyer sur le choix de canal, le canal ne sera pas commuté.
33
Utilisation du Traqueur Enfant
BB
Be
35
channel
LED
channel
b. Quand il y a plusieurs Unités Enfant :
LED
Si l’Unité Parent correspond à plusieurs l’Unités Enfant, vous pouvez appuyer sur le
bouton de choix de canal pour choisir l’Unité Enfant que vous voulez surveiller. Quand
l’Unité Enfant choisie est dans la marge d’avertissement, le LED rouge du canal,
s’allumera. Quand l’unité choisie d’enfant est hors de la gamme d’avertissement,
le LED du canal clignotera en rouge. Les autres LED des canaux de l’Unité Parents
correspondant aux l’Unité Enfant configurées s’allumeront en vert quand les Unités
Enfant sont dans la marge d’avertissement. Quand les Unité Enfant sont hors de la
gamme d’avertissement mais dans la marge de surveillance, le LED vert clignotera.
Quand les unités d’enfant sont hors de gamme de surveillance valide, le canal LED
s’éteindra.
34
Utilisation du Traqueur Enfant
FRANCAIS
Ajouter des Unités Enfant
Quand vous voulez ajouter plus d’Unité Enfant à l’Unité Parents, retenez les boutons Trouver/initiation Unité enfant de l’Unité Parents et
le bouton désiré de Trouver de l’Unité Enfant pendant dix secondes.
Puis les bippers des Unités Parents et Enfant feront bip-bip pour vous
informer que l’Unité Enfant est ajoutée. Le canal de la nouvelle Unité
Enfant supplémentaire sera automatiquement placé sur le canal le
Be
channel
LED
plus bas restant.
Retirer des Unités Enfant
Quand vous voulez retirer une des Unité Enfant à partir de l’Unité Parents, retenez svp le bouton de choix de canal/effacement Unité enfant pendant dix secondes. Alors le bipper de l’unité de parents fera
bip-bip pour vous informer que l’Unité Enfant est enlevée. Veuillez
noter quand vous retirer complètement, l’Unité Enfant et l’Unité Parents ne peuvent pas être connectées. Si vous voulez les relier, répétez
Be
channel
LED
svp les étapes décrivant l’ajout d’Unités d’enfant.
35

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.4
Linearized                      : No
Encryption                      : Standard V1.2 (40-bit)
User Access                     : Print, Fill forms, Extract, Assemble, Print high-res
Modify Date                     : 2006:12:08 13:54:10+08:00
Create Date                     : 2006:12:08 13:52:04+08:00
Creator                         : Adobe InDesign CS2 (4.0)
Producer                        : Adobe PDF Library 7.0
Page Count                      : 37
Mod Date                        : 2006:12:08 13:54:10+08:00
Creation Date                   : 2006:12:08 13:52:04+08:00
Metadata Date                   : 2006:12:08 13:54:10+08:00

EXIF Metadata provided by EXIF.tools