Tranwo Technology VM2506 2.4GHz Digital RF Module User Manual

Tranwo Technology Corp 2.4GHz Digital RF Module

User Manual

Model : VM2506
1. PRODUCT DESCRIPTION 2. Features • CMOS Technology with RF, Baseband, and MAC Integrated. • 1T1R Mode with 150Mbps PHY Rate for Both Transmit and Receiving. • Legacy and High Throughput Modes • 20MHz/40MHz Bandwidth • Reverse Direction Grant Data Flow and Frame Aggregation • WEP 64/128, WPA, WPA2, TKIP, AES • QoS‐WMM, WMM‐PS • WPS, PIN, PBC • Multiple BSSID Support • USB 2.0 • International Regulation ‐ 802.11d + h • Cisco CCX Support • Bluetooth Co‐existence • Low Power with Advanced Power Management • Operating Systems ‐ Windows XP 32/64, 2000, Vista 32/64, Linux, Macintosh. The VM2506 is a highly integrated MAC/BBP and 2.4 GHz RF single chip with 150Mbps PHY rate supporting. It fully complies with IEEE 802.11n draft 3.0 and IEEE802.11 b/g /n feature rich wireless connectivity at high standards, delivers reliable, cost effective, throughput from an extended distance. Optimized RF architecture and baseband algorithms provide superb performance and lowpower consumption. Intelligent MAC design, deploys a high efficient USB engine and hardware data processing accelerators without overloading the host processor. The VM2506 is designed to support standard based features in the areas of security, quality of service and international regulation, giving end users the greatest performance anytime in any circumstance.
3. Temperature Limit Ratings 4. PRODUCT SPECIFICATIONS Standards WiFi: EEE 802.11b, IEEE 802.11g, IEEE 802.11n Bus Interface WiFi: USB2.0 Data Rate 802.11b: 11, 5.5, 2, 1 Mbps 802.11g: 54, 48, 36, 24, 18, 12, 9, 6 Mbps 802.11n: MCS 0 to 7 for HT20MHz ;MCS 0 to 7 for HT40MHz Modulation Techniques 802.11b: CCK, DQPSK, DBPSK 802.11g: 64 QAM, 16 QAM, QPSK, BPSK 802.11n: 64 QAM, 16 QAM, QPSK, BPSK Operating Channel WiFi 2.4GHz: 11: (Ch. 1-11) – United States Frequency Range 2400MHz ~ 2483.5 MHz Security WiFi : WPA, WPA2 , WPS2.0, WAPI OS supported Linux/Android
5.Electrical Specifications 1.RF Characteristics for IEEE802.11b ( 11Mbps mode unless otherwise specified) Items Contents Contents IEEE802.11b Mode CCK 11 Mbps Channel frequency 2400 ~ 2483.5 MHz RX (per≤85dBm@8%) -85 dBm TX Power Level 506.991mWEVM (≤-28) -28 2. RF Characteristics for IEEE802.11g ( 54Mbps mode unless otherwise specified) Items Contents Contents IEEE802.11g Mode OFDM 54 Mbps Channel frequency 2400 ~ 2483.5 MHz RX (per≤70dBm@10%) -70 dBm Power Level 506.991mWEVM (≤-28) -28 dBm 3. RF Characteristics for IEEE802.11n (BW20_MCS7) Items Contents Contents IEEE802.11n (BW20_MCS7) Mode OFDM 65 Mbps Channel frequency 2400 ~ 2483.5 MHz RX (per≤65 dBm@10%) -65 dBm Power Level 506.991mW EVM (≤-28) -28 dBm 4. RF Characteristics for IEEE802.11n (BW40_MCS7) Items Contents Contents IEEE802.11n (BW40_MCS7) Mode OFDM 135 Mbps Channel frequency 2400 ~ 2483.5 MHz RX (per≤65 dBm@10%) -65 dBm Power Level 506.991mW EVM (≤-28) -28 dBm
3.3V6.Pin Assignment
注意事项材质厚度高度精度要求屏蔽盖厚度 包括材质厚度吴林海T=0.2 洋白铜拓 联X11-4 為重要尺寸深 圳 市 佰 汶 科 技 有 限 公 司硬度:披鋒要求 料厚 披鋒 以下 料厚 披鋒 以下備註生產流程工序名稱負責部門:製圖:日期批准:審核:日期日期客戶貨號产品名称 模具編號 :材質:客戶名稱 :電鍍 其它 不電鍍工程圖比例:單位:版本:佰汶編號 原材料檢查 生 產 生 產 抽 查生产冲压首檢品管 品管 品管包装包装部抽 查品管出货包装部出货前检查品管63-1500.050.080.150.10.40.316-630.24-160.12<4±A级 B级等级一般公差0.60.40.30.21.20.70.40.3C级 D级版次 修改说明 绘图 审核 核准17.10±0.131.74±0.12.00±0.11.25±0.11.25±0.11.25±0.10.152.00±0.15.574.343.49Shielding case drawing
Connector Dim.
Federal Communication Commission Interference Statement This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures: - Reorient or relocate the receiving antenna. - Increase the separation between the equipment and receiver. - Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. - Consult the dealer or an experienced radio/TV technician for help. FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.
FOR MOBILE DEVICE USAGE (>20cm/low power) Radiation Exposure Statement: This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body. This device is intended only for OEM integrators under the following conditions: The transmitter module may not be co-located with any other transmitter or antenna. As long as this conditions above is met, further transmitter test will not be required. However, the OEM integrator is still responsible for testing their end-product for any additional compliance requirements required with this module installed IMPORTANT NOTE: In the event that these conditions can not be met (for example certain laptop configurations or co-location with another transmitter), then the FCC authorization is no longer considered valid and the FCC ID can not be used on the final product. In these circumstances, the OEM integrator will be responsible for re-evaluating the end product (including the transmitter) and obtaining a separate FCC authorization. End Product Labeling FOR MOBILE DEVICE USAGE (>20cm/low power) This transmitter module is authorized only for use in device where the antenna may be installed such that 20 cm may be maintained between the antenna and users. The final end product must be labeled in a visible area with the following: “Contains FCC ID:O6L-VM2506”. The grantee's FCC ID can be used only when all FCC compliance requirements are met. Manual Information To the End User The OEM integrator has to be aware not to provide information to the end user regarding how to install or remove this RF module in the user’s manual of the end product which integrates this module. The end user manual shall include all required regulatory information/warning as show in this manual.
Approved antenna(s) list Model Type Gain(dBi) Frequency range(GHz) Connecter VM2506RX Dipole 2 2.4~2.5 i-pex VM2506TX Dipole 2 2.4~2.5 i-pex

Navigation menu