Tranzeo Wireless Technologies 2458NT2G WIRELESS NETWORKING DEVICE User Manual Multipoint UG v1 170706 pub

Download:
Mirror Download [FCC.gov]
Document ID	682404
Application ID	zh+uIsWeDc+cMdJ0mdRzfA==
Document Description	USERS MANUAL
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	253.25kB (3165683 bits)
Date Submitted	2006-07-18 00:00:00
Date Available	2006-07-18 00:00:00
Creation Date	2006-07-17 16:45:00
Producing Software	GPL Ghostscript 8.15
Document Lastmod	2006-07-17 16:45:00
Document Title	Multipoint_UG_v1_170706.pub
Document Creator	PScript5.dll Version 5.2
Document Author:	Cecilia Vallejo

TR-Multi Series
Tranzeo TR-Multi Series
User Guide
Revision: 1.0
Firmware: 2.10
Date: 7/06/06
Document Revisions:
Version 1.0
June 9, 2006
Tranzeo Wireless Technologies Inc.
19473 Fraser Way
Pitt Meadows, BC
Canada V3Y 2V4
Toll Free Number: 1.866.872.6936
T echnical Support: 1.888.460.6366
Local Number: 1.604.460.6002
Fax Number: 1.604.460.6005
iiiiii
This document is intended for Public Distributio n
Pitt Meadows, B.C. Canada V3Y 2V4
General Inquiries: info@tranzeo.com
Sales: sales@tranzeo.com
T echnical Support: support@tranzeo.com
19473 Fraser Way,
ii
Tranzeo Wireless Technologies
Safety Information
Safety Information
FCC Compliance
This device has been tested and found to comply with the limits for a Class B digital device
pursuant to Part 15 of the FCC rules. T hese limits are designed to provide reasonable
protection against harmful interference when the device is operated in a residential
environment. This device generates, uses, and can radiate radio frequency energy. If not
installed and used in accordance with the user guide, may cause harmful interference to radio
communication. In case of harmful interference, the users will be required to correct the
interference at their own expense.
The users should not modify or change this device without written approval from T ranzeo
Wireless. Modification could void authority to use the device.
For safety reasons, people should not work in a situation where RF exposure limits could be
exceeded. T o prevent this situation, the users should consider the following rules:
•
•
Install the antenna so that there is a minimum of 59 cm of distance between the antenna
and people.
Do not turn on power to the device while installing the antenna.
•
Do not connect the antenna while the device is in operation.
Do not collocate or operate the antenna used with the device in conjunction with any
other antenna or transmitter.
•
Use this product only with the following T ranzeo antennas of the same or lower gain:
•
T R-OD24-12 – 2.4 GHz 12 dBi dipole
T R-24H-90-17 – 2.4 GHz 17 dBi sector
T R-GD24-24 – 2.4 GHz 24 dBi grid
T R-5X-ANT-24 – 5.8 GHz 24 dBi Patch antenna
T R-5.8-32DB-ANT – 5.8 GHz 32 dBi Dish antenna
T R-58H-90-16 – 5.8 GHz 16 dBi Sector antenna
T R-HTQ-5.8-12 – 5.8 GHz 12 dBi Omni antenna
•
In order to ensure compliance with local regulations, the installer MUST enter the gain
of the antenna at the time of installation. See Chapter 3, Wireless Settings, for details.
Professional Installation Required
The product requires professional installation. Professional installers ensure that the
equipment is installed following local regulations and safety codes.
TR-Multi Series
Pitt Meadows, B.C. Canada V3Y 2V4
iiiiiiiii
This document is intended for Public Distributio n
19473 Fraser Way,
iii
Tranzeo Wireless Technologies
Safety Information
Safety Instructions
You must read and understand the following safety instructions before installing the device:
•
•
•
•
•
This antenna’s grounding system must be installed according to Articles 810-15,
810-20, 810-21 of the National Electric Code, ANSI/NFPA No. 70-1993. If you have
any questions or doubts about your antenna’s grounding system, contact a local
licensed electrician.
Never attach the grounding wire while the device is powered.
If the ground is to be attached to an existing electrical circuit, turn off the circuit before
attaching the wire.
Use the Tranzeo Power over Ethernet (POE) adapter only with approved T ranzeo
models.
Never install radio equipment, surge suppressors or lightning protection during a storm.
Lightning Protection
The key to lightning protection is to provide a harmless route for lightning to reach ground.
The system should not be designed to attract lightning, nor can it repel lightning. National,
state and local codes are designed to protect life, limb, and property, and must always be
obeyed. When in doubt, consult local and national electrical codes or contact an electrician or
professional trained in the design of grounding systems.
TR-Multi Series
Pitt Meadows, B.C. Canada V3Y 2V4
iviviv
This document is intended for Public Distributio n
19473 Fraser Way,
iv
Tranzeo Wireless Technologies
Table of Contents
Table of Contents
Chapter 1: Overview ................................................................. 1-1
Introduction.......................................................................................................1-1
Product Kit........................................................................................................1-1
Product Description..........................................................................................1-2
LED Panel Indicators...................................................................................1-2
Chapter 2: Hardware Installation ................................................ 2-1
Getting Ready ...................................................................................................2-1
Tools Required.............................................................................................2-1
Site Selection ...............................................................................................2-1
Orientation of the Radio ..............................................................................2-1
Power Supply...............................................................................................2-1
Installing the Ethernet Cable ............................................................................2-2
M ounting the Radio ..........................................................................................2-4
Grounding the Antenna.....................................................................................2-4
Connecting the Radio .......................................................................................2-5
Best Practices....................................................................................................2-6
Chapter 3: Configuration............................................................ 3-1
Connecting to the Radio ...................................................................................3-1
Changing the IP Address - Windows XP ....................................................3-1
Changing the IP Address Using the Tranzeo Locator.................................3-2
Login into the Configuration Interface .............................................................3-3
Information Page ..............................................................................................3-4
CPE Setup M enu...............................................................................................3-5
Wireless Settings .........................................................................................3-5
Administrative Settings ...............................................................................3-6
Security.............................................................................................................3-7
Basic Security Settings ................................................................................3-7
Advanced Security Settings .........................................................................3-8
Status.................................................................................................................3-9
AP List.........................................................................................................3-9
ARP Table ...................................................................................................3-9
Statistics.....................................................................................................3-10
System Performance ..................................................................................3-12
TR-Multi Series
Pitt Meadows, B.C. Canada V3Y 2V4
vvv
This document is intended for Public Distributio n
19473 Fraser Way,
Tranzeo Wireless Technologies
Table of Contents
Network Configuration...................................................................................3-13
Router M ode..............................................................................................3-14
DHCP Configuration .................................................................................3-15
IP Routing..................................................................................................3-16
Quality of Service ......................................................................................3-17
Port Forwarding.........................................................................................3-18
Port Filtering..............................................................................................3-19
Appendix A: Grounding and Lightning Protection Information ... A-1
Appendix B: Product Specification............................................. B-1
Appendix C: Protocol List .......................................................... C-1
Appendix D: Common TCP Ports ............................................... D-1
TR-Multi Series
Pitt Meadows, B.C. Canada V3Y 2V4
vivivi
This document is intended for Public Distributio n
19473 Fraser Way,
vi
Tranzeo Wireless Technologies
Chapter 1: Overview
Chapter 1: Overview
Introduction
The T R-Multi Series radios, the T R-Multi-N and T R-Multi-2, are advanced
customer premises equipments (CPE) that offer the dual band capabilities of
802.11b and 802.11a within one unit. These integrated, dual band/antenna radios
allow for quicker installs where they can be configured in either 2.4 GHz or 5 GHz
frequency, eliminating the need for two types of radios.
The T R-Multi-2 radios come with a built-in antenna. The T R-Multi-N radios do
not include an antenna.
Product Kit
The T R-Multi Series product kit contains the items shown below. If any item is
missing or damaged, contact your local dealer for support.
T R-Multi-N/
T R-Multi-2 x 1
Ethernet boot
cover x 1
Gasket x 1
Keps nuts x 8
Ethernet cable
x 3 feet
Pitt Meadows, B.C. Canada V3Y 2V4
U-bolt w/ 2 nuts x 1
Lock washers x 2
Strain relief x 1
TR-Multi Series
Mounting bracket x 1
111
This document is intended for Public Distributio n
19473 Fraser Way,
POE adapter x 1
DC power adapter x 1
1-1
Tranzeo Wireless Technologies
Chapter 1: Overview
Product Description
The LEDs, ports and product information are located at the back of the T R-Multi
Series radio, as shown in the picture.
Ethernet ports
LED Panel indicators
Studs for the boot
cover
Serial number
Mac address
Studs for the
mounting bracket
LED Panel Indicators
Label
Color *
Indicators
Power
● Green
On: Powered on
Off: No power
LAN
● Green
On: Ethernet link
Flashing: Ethernet traffic
Off: No Ethernet link
Radio
● Green
On: Radio link
Flashing: Radio activity
Off: No radio link
*Note: Color of the LED panel indicators may vary.
TR-Multi Series
Pitt Meadows, B.C. Canada V3Y 2V4
222
This document is intended for Public Distributio n
19473 Fraser Way,
1-2
Tranzeo Wireless Technologies
Chapter 2: Hardware Installation
Chapter 2: Hardware Installation
The T R-Multi Series radios are easy to install, as you’ll see in this chapter. Before
starting, you will need to get the tools listed below and decide about the site and
orientation of the device. Once ready, follow the instructions about how to install
the Ethernet cable, mount the device, ground the antenna, and make the
connections in order to get a proper installation.
Getting Ready
Tools Required
To install your T R-Multi Series radio you will need the following tools:
•
•
•
•
•
•
•
•
1/2” wrench x 1
3/8” wrench x 1
3/4” wrench x 1
Cat 5 cable stripper
RJ-45 crimper x 1
Cat 5 cable, enough to bring the signal from the radio to the Power over
Ethernet (POE) adapter
RJ-45 connectors x 2
#6 green grounding wire
Site Selection
Determine the location of the radio before installation. Proper placement of the
device is critical to ensure optimum radio range and performance. You should
perform a site survey to determine the optimal location. Ensure the CPE is within
line-of-sight of the access point (AP). Obstructions will impede performance of
this device.
Orientation of the Radio
Determine if the orientation of the radio will be horizontal or vertical before
installation. T he T R-Multi Series radios can be mounted in either orientation. The
Ethernet boot cover should always be placed so that the cable runs toward the
ground for maximum environmental protection.
Power Supply
Only use the power adapter supplied with the T R-Multi Series radio. Otherwise,
the product may be damaged and will not be covered by the Tranzeo warranty.
TR-Multi Series
Pitt Meadows, B.C. Canada V3Y 2V4
111
This document is intended for Public Distributio n
19473 Fraser Way,
2-1
Tranzeo Wireless Technologies
Chapter 2: Hardware Installation
Installing the Ethernet Cable
Step 1:
Insert the strain relief, without the cap nut,
into the port opening of the boot cover.
Step 2:
Using a 3/4” wrench, tighten the strain
relief until it touches the boot cover.
IMPORT ANT ! Use hand tools only. Do
not over tighten.
Step 3:
Put the cap nut back over the strain relief
and insert the Cat 5 cable through it. Wire
the cable following the EIA/T IA T 568B
standard, and attach the RJ-45 connectors
to each end of the cable.
Step 4:
If you bought the device with dual port,
repeat steps 1, 2, and 3 for the second port.
IMPORT ANT ! If you are not going to use
the second port, insert the strain relief into
the boot cover and tighten the cap nut to
ensure a weather-tight seal, as shown in
the picture.
TR-Multi Series
Pitt Meadows, B.C. Canada V3Y 2V4
222
This document is intended for Public Distributio n
19473 Fraser Way,
2-2
Tranzeo Wireless Technologies
Chapter 2: Hardware Installation
Step 5:
Place the gasket—with the adhesive side
facing up—over the 4 studs around the port
of the radio. Flatten the gasket ensuring
there are no gaps. Remove the backing.
Step 6:
Plug the Cat 5 cable inserted in the boot
cover into the port. Remember to place the
boot cover according to the desired
polarization, so that the strain relief faces
the ground.
Step 7:
Fit the boot cover over the 4 studs and the
gasket. Secure with 4 keps nuts. Tighten
with a 3/8” wrench until the gasket is at
least 50% compressed.
Step 8:
Make sure the cap nut of the strain relief is
tightened properly to ensure a weatherproof seal.
IMPORT ANT ! Hand tighten only. Do not
over tighten as you may damage the
weather-tight seal of the strain relief.
TR-Multi Series
Pitt Meadows, B.C. Canada V3Y 2V4
333
This document is intended for Public Distributio n
19473 Fraser Way,
2-3
Tranzeo Wireless Technologies
Chapter 2: Hardware Installation
Mounting the Radio
Step 9:
Attach the mounting bracket to the pole
using the U-bolt. Secure the U-bolt with
the lock washers and the nuts. Align if
necessary, and then tighten the nuts enough
to prevent any movement.
Step 10:
Fit the radio to the mounting bracket.
Secure the radio with keps nuts.
IMPORT ANT ! The strain relief must be
always facing the ground.
Grounding the Antenna
Step 11:
Using a #6 green grounding wire, connect
the grounding lug on the radio to a proper
ground. See Appendix A: Grounding and
Lighting Protection Information.
IMPORT ANT : This device must be grounded. Connect the green grounding wire
to a known good earth ground, as outlined in the National Electrical Code.
TR-Multi Series
Pitt Meadows, B.C. Canada V3Y 2V4
444
This document is intended for Public Distributio n
19473 Fraser Way,
2-4
Tranzeo Wireless Technologies
Chapter 2: Hardware Installation
Connecting the Radio
Step 12:
Connect the Cat 5 cable from the radio into
the RJ-45 jack marked “ CPE” on the POE
adapter. The POE adapter is not weatherproof and should be installed indoors.
Step 14
Step 12
Step 13
Step 13:
Connect the power adapter to the POE
adapter and plug the other end to an outlet.
The POE adapter will be powered on and
the power indicator on the top panel will
turn on. We recommend to connect the
power adapter to an outlet with surge
suppression capability with an uninterrupted
power supply (UPS) for reduced outages.
IMPORT ANT ! Use the power adapter
supplied with the radio. Otherwise, it may
be damaged.
Step 14:
To configure the T R-Multi Series radio,
connect the Ethernet cable to the POE
adapter and to a computer. Ensure that the
distance between the computer and the
radio does not exceed 328 feet.
Note: If connecting to a hub or switch, a
crossover cable may be required.
TR-Multi Series
Pitt Meadows, B.C. Canada V3Y 2V4
555
This document is intended for Public Distributio n
19473 Fraser Way,
2-5
Tranzeo Wireless Technologies
Chapter 2: Hardware Installation
Best Practices
Follow these practices to ensure a correct installation and grounding.
•
•
•
•
•
Always try to run long Cat 5 and LMR cables inside of the mounting pole.
This helps to insulate the cable from any air surges.
Keep all runs as straight as possible. Never put a loop into the cables.
T est all grounds to ensure that you are using a proper ground. If using an
electrical socket for ground, use a socket tester, such as Radio Shack 22-141.
Keep a copy of the National Electrical Code Guide at hand and follow its
recommendations.
If you are in doubt about the grounding at the location, drive your own rod
and bond it to the house ground. At least you will know that one rod is
correct in the system.
TR-Multi Series
Pitt Meadows, B.C. Canada V3Y 2V4
666
This document is intended for Public Distributio n
19473 Fraser Way,
2-6
Tranzeo Wireless Technologies
Chapter 3: Configuration
Chapter 3: Configuration
The T R-Multi Series radios can be configured through an HTML configuration
interface, accessible using any Internet browser. T he configuration interface
allows you to define and change settings, and also shows information about the
performance of the device.
In this chapter we’ll cover how to:
•
•
•
Access the configuration interface
Configure the T R-Multi Series radio
Interpret the information displayed in the interface
Connecting to the Radio
Before accessing the configuration interface, you have to change the network
connection settings in your computer to be on the same subnet as the radio.
Changing the IP Address - Windows XP
1. In your computer, open Control Panel > Network Connections > Local Area
Connection.
2.
In Local Area Connection Status > General, click Prope rties.
3.
In Local Area Connection Properties > General, select Inte rnet Protocol
(TCP/IP) and click Prope rties.
4.
In Internet Protocol (T CP/IP) Properties > General, select Use the following
IP addre ss.
5.
Enter your IP address and Subne t Mask. The default IP address of the radio
is 192.168.1.100, which cannot be used here.
6.
Click O K and Close.
TR-Multi Series
Pitt Meadows, B.C. Canada V3Y 2V4
111
This document is intended for Public Distributio n
19473 Fraser Way,
3-1
Tranzeo Wireless Technologies
Chapter 3: Configuration
Changing the IP Address Using the Tranzeo Locator
The Tranzeo Locator is a utility that allows users to quickly change the IP address
of the Tranzeo radios. It sends out a broadcast on the network and displays a list of
other T ranzeo radios connected, from which you can configure the IP address for
your device.
Note: The Locator cannot locate radios through routers.
The Tranzeo Locator displays the following options:
Scan:
Configure:
Upgrade:
Web:
Auto IP:
Locates Tranzeo radios connected to the network. A
yellow icon appears before the name when the radio is
not in the same subnet.
Used to set a static IP address or set the radio into
DHCP mode.
Under development.
Opens a browser to access the configuration interface.
To automatically set the radio to an IP address one
number higher than the IP address of the computer.
Find the latest version of the T ranzeo Locator at www.tranzeo.com, under Tranzeo
Support > Support Files > Radio Utilities.
TR-Multi Series
Pitt Meadows, B.C. Canada V3Y 2V4
222
This document is intended for Public Distributio n
19473 Fraser Way,
3-2
Tranzeo Wireless Technologies
Chapter 3: Configuration
Login into the Configuration Interface
After defining the network settings, follow these steps to login into the Tranzeo
Configuration Interface.
1.
Open your Internet browser (Internet Explorer, Netscape, or Firefox).
2.
In the address bar, type http://192.168.1.100.
3.
In the login dialog, enter your Use rname and Password (if you’re a firsttime user, follow the instructions below).
4.
Click O K. You will then access the configuration interface.
If you’re a first-time user:
1.
Enter username admin and password de fault.
2.
In the Password Set/Reset window, change the Administration and
Re covery* passwords. They cannot be left as default and must be different
from each other. You can change the usernames too.
3.
Click Apply to save the changes.
4.
You will be prompted to enter your new username and password in the login
dialog. You will then access the configuration interface.
* The recovery username and password are used to access the Password Set/Reset
window if the administration password is lost.
TR-Multi Series
Pitt Meadows, B.C. Canada V3Y 2V4
333
This document is intended for Public Distributio n
19473 Fraser Way,
3-3
Tranzeo Wireless Technologies
Chapter 3: Configuration
Information Page
This is the first window of the configuration interface. It shows the main menu and
information about the device settings, like wireless, network, and security settings.
The menu is divided in four sections:
•
•
•
•
CPE Setup Menu
Security
Status
Network
Each section contains navigation links to the configuration windows.
TR-Multi Series
Pitt Meadows, B.C. Canada V3Y 2V4
444
This document is intended for Public Distributio n
19473 Fraser Way,
3-4
Tranzeo Wireless Technologies
Chapter 3: Configuration
CPE Setup Menu
In this section you would be able to configure wireless and administrative settings
for the T R-Multi Series radio.
Wireless Settings
This window displays the wireless configuration of the device.
Primary SSID:
Secondary SSID:
Band:
TX Rate:
RTS Threshold:
The Service Set Identifier (SSID) is the name that
identifies a specific wireless LAN. Devices must have
the same SSID to communicate with each other.
Used when the primary access point is unavailable.
The radio frequency range in which the radio operates.
The transmission speed at which the radio
communicates with the access point.
When a packet exceeds the RT S threshold, the CPE
sends first a ‘request to send’ (RT S) to the access point
instead of sending the packet automatically.
Fragmentation
Threshold:
This is the size at which packets are fragmented in
order to be transmitted.
Link Distance:
This is the distance between the CPE and access point.
This setting is necessary to define the correct ACK
timing. Setting this value too low will result in low
throughput and high retries.
ACK Timeout Tuning:
The time that the device waits for an acknowledgment
from the access point accepting the transmission
before re-attempting to send the data. This is an offset
from the ACK timing set by the link distance.
TR-Multi Series
Pitt Meadows, B.C. Canada V3Y 2V4
555
This document is intended for Public Distributio n
19473 Fraser Way,
3-5
Tranzeo Wireless Technologies
Chapter 3: Configuration
Power Cap:
Country:
Antenna Gain:
Preamble:
TR-Multi Series
Pitt Meadows, B.C. Canada V3Y 2V4
Is the maximum output power of the radio.
Select the country from where the device is operating.
Setting an incorrect country may be considered a
violation of the applicable law.
Select the gain of the antenna used. This information
MUST be entered by the installer at the time of
installation.
Select type: Long uses long preamble only, Auto
(recommended) tries short preamble first, then long.
666
This document is intended for Public Distributio n
19473 Fraser Way,
3-6
Tranzeo Wireless Technologies
Chapter 3: Configuration
Adm inistrative Settings
Use this section to upgrade the software, change your password, and define SNMP
parameters.
Upgrade Software:
Defaults:
Reboot:
Rollback:
Device Name:
User Name:
Password:
Confirm Password:
Extended Wireless
Information:
Signal/Status LEDs:
SNMP Parameters:
TR-Multi Series
Pitt Meadows, B.C. Canada V3Y 2V4
Enter the location of the software update file or
Browse to locate it in your computer. Click Upgrade
Software . If the radio does not refresh the Information
Page after 1 minute, press Refresh, Reload or F5.
Verify the new firmware is installed correctly.
Returns all settings to factory defaults, including
passwords.
Restarts the system without changing settings.
To undo the most recent change.
This is the network name of the device.
This is the login username.
Enter a new password if you want to change it.
Re-type the new password.
Enables extended information (name and IP address),
which is only displayed with T ranzeo access points.
Un-check to turn off the LED panel indicators.
Here you set the Re ad Community string and
Contact/Location information. It’s highly
recommended that you change the Read Community
string immediately to prevent unauthorized scanning
of your network.
777
This document is intended for Public Distributio n
19473 Fraser Way,
3-7
Tranzeo Wireless Technologies
Chapter 3: Configuration
Security
In this section you can configure both basic and advanced security settings for
your device.
Basic Security Settings
In this window you can define WEP parameters. WEP provides security by
encrypting data so that it’s protected when transmitted from one point to another.
Enabled:
Check to turn on WEP security protocol.
Authentication:
Select your system to be open or shared. Open is
always recommended.
Key Length:
This is the level of encryption. Note that 64 bit is
referred to as 40 bit on some systems.
Default Key:
Select the default WEP key from the list.
Activate Keys:
TR-Multi Series
Pitt Meadows, B.C. Canada V3Y 2V4
Enter the four WEP keys you want to activate. Keys
must be entered in HEX only.
888
This document is intended for Public Distributio n
19473 Fraser Way,
3-8
Tranzeo Wireless Technologies
Chapter 3: Configuration
Advanced Security Settings
In this window you can enter WPA parameters. WPA provides a higher level of
security, enhancing the security features of WEP.
Enabled:
Cipher Type:
PSK:
Check to turn on WPA.
Select the level of encryption.
Enter your PSK password.
Update Interval:
This is the interval at which the PSK password will be
updated.
Authentication:
Ensures that only authorized network users can access
the network. Enter the information about the RADIUS
server from your Internet Service Provider.
TR-Multi Series
Pitt Meadows, B.C. Canada V3Y 2V4
999
This document is intended for Public Distributio n
19473 Fraser Way,
3-9
Tranzeo Wireless Technologies
Chapter 3: Configuration
Status
This section displays information about the status and performance of your radio.
Most options and information cannot be modified in this section.
AP List
This window displays information about the access points associated with the CPE
and the connection statistics.
You can set an access point’s SSID as your primary SSID by clicking on the Mac
address when it’s displayed as a link. This will automatically reboot the radio.
ARP Table
This table lists the devices that have communicated with your device. There
should be a limited number of entries in this table, especially if the interstation
blocking is turned on at the access point.
TR-Multi Series
Pitt Meadows, B.C. Canada V3Y 2V4
101010
This document is intended for Public Distributio n
19473 Fraser Way,
3-10
Tranzeo Wireless Technologies
Chapter 3: Configuration
Statistics
This section is divided in 3 windows: LMAC (Lower Mac), UMAC (Upper Mac),
and Ethernet, which can be accessed from the Statistic Summary Page.
LMAC Statistics
The LMAC functions occur in the radio chipset. While the UMAC divides the
statistics into clean and failed packets, LMAC defines why packets failed.
This window contains three tabs: T X, RX and INT. TX and RX values are useful
to ISPs and other users. T he INT (internal) statistics are intended for use by
Tranzeo Wireless T echnical Support.
You can click onto each speed level and see how the traffic breaks down. In the
T X statistics, there should little to no Tries at Series 2, 3 or 4. T he radio will try to
send a packet 4 times at Series 1 and then will try the next series 4 times. In the
RX statistics, you should look for bad CRCs and bad decrypts for signs of RF
interference or Fresnel interference links. Bad PHYs generally are caused when
the radio is unable to decode the packets due to noise.
Note: Communication between access points and CPEs always occurs at the
lowest rate. In a normal link, you should see a fair number of transactions at the
lowest rate.
TR-Multi Series
Pitt Meadows, B.C. Canada V3Y 2V4
111111
This document is intended for Public Distributio n
19473 Fraser Way,
3-11
Tranzeo Wireless Technologies
Chapter 3: Configuration
UMAC Statistics
The UMAC functions occur in the unit’s processor. T he UMAC statistics are
likely the most useful for radio troubleshooting. This window breaks down the
statistics into clean and failed packets.
The failed packets should be less than 10% in a normal operating environment. In
the T X statistics, there should be little to no Retransmits at Series 2, 3 or 4. Life
Statistics are reset on each reboot.
Ethernet Statistics
In this window, excessive collisions are usually a sign that the radio and the device
it is linked to are not on the same duplex settings. One is at full while the other is
at half. T ry locking both to the same values.
Collisions do normally occur on an Ethernet network and are generally handled by
the Carrier Sense Multiple Access with Collision Detect (CSMA/CD) mechanism.
Alignment, length and excessive FCS errors could the result of a bad radio link, or
a bad Ethernet cable.
TR-Multi Series
Pitt Meadows, B.C. Canada V3Y 2V4
121212
This document is intended for Public Distributio n
19473 Fraser Way,
3-12
Tranzeo Wireless Technologies
Chapter 3: Configuration
System Performance
This window shows information about the memory usage and the CPU. Many
browsers do not allow infinite refreshes of a page through scripts, so this window
may stop updating. If it does, simply change the refresh rate to another value to
restart the process.
TR-Multi Series
Pitt Meadows, B.C. Canada V3Y 2V4
131313
This document is intended for Public Distributio n
19473 Fraser Way,
3-13
Tranzeo Wireless Technologies
Chapter 3: Configuration
Network Configuration
In this window you can control the network configuration of the device. First, you
must define if your radio will operate as a bridge or router. The content of the
window varies slightly depending on your selection.
When changing modes, the radio may need to reboot before certain features
become available.
Router
Bridge
The following are features common to bridge or router mode. Router specific
features are described in the next page.
Cloning Mac Address:
IP Mode:
WAN:
Ethernet Port Speed:
TR-Multi Series
Pitt Meadows, B.C. Canada V3Y 2V4
This feature allows the radio to copy the Mac address
of the device you have connected to the network. This
is useful when you change your device and don’t want
to register a new Mac address, or when dealing with
some PPPoE and Radius implementations. When the
device is cloning a Mac address, it can only be
managed from the LAN side. T o clone a Mac address,
check the Mac Address box and enter the Mac
address in the field Cloning into. Uncheck to restore
the original Mac address.
You can select to use Static IP, DHCP Client
(dynamic), or PPPoE (available only for router).
Note: If a DHCP server is not available, the device
will try to get an IP for up to 5 minutes. After that, it
will fall back to a static IP.
Enter the information related to the WAN interface: IP
Address, Subnet Mask, Gateway, DNS1, DNS2, and
Domain Name.
Set as Auto by default.
141414
This document is intended for Public Distributio n
19473 Fraser Way,
3-14
Tranzeo Wireless Technologies
Chapter 3: Configuration
Router Mode
The following features are available if you select Router mode in the Network
Configuration window.
From this window you can access specific windows to configure the DHCP
Server, QoS, Static Routes, Port Filtering, and Port Forwarding. If the feature is
available, it will appear like a link. T o open an item, just click on it. These features
are described in the next pages.
MTU:
Allow Pinging:
Allow Access to Web
Server:
IP Mode:
The Maximum T ransmission Unit (MT U) refers to the
size of the largest packet that the router can pass. T he
default value is 1500 bytes. If PPPoE is used, you
should change the MT U to match the PPPoE server,
typically 1492 bytes.
Enables ping responses on WAN interface.
Allows access from WAN interface or change the port
the WAN server responds to web server requests.
Note: Access to web server from LAN interface is
always enabled and set at port 80.
You can select to use Static IP, DHCP Client
(dynamic), or PPPoE. If no PPPoE server is found,
you may not be able to access the radio from the WAN
side, but you will still be able to get access from the
LAN interface.
LAN:
Enter the information related to the LAN interface: IP
address and subnet mask.
DHCP Server:
Check the box and click Apply to enable this feature.
Click on the item (which now appears in blue) to open
the DHCP Server configuration window.
Routing:
Port Management:
Enables NAT , QoS, and Static Routes. NAT should
always be enabled when using private addressing.
Click on QoS or Static Routes to configure.
Check the box and click Apply to enable port filtering
and port forwarding. Click on any item to open the
configuration window.
Note: Many Ethernet devices do not auto-negotiate properly. If you see large
numbers of dropped pings, you may have collisions. Try locking the device at 10 /
Half as a troubleshooting step. If the packet losses stop, step up to 100 / Half. If
the device the radio is connecting cannot support 100 / Half, you should replace
the device or place a switch in line.
TR-Multi Series
Pitt Meadows, B.C. Canada V3Y 2V4
151515
This document is intended for Public Distributio n
19473 Fraser Way,
3-15
Tranzeo Wireless Technologies
Chapter 3: Configuration
DHCP Configuration
This window shows the configuration of the DHCP server.
IP Parameters
Subnet Mask:
Enter your subnet mask in this field.
Address Starting from:
Indicates the first address in the DHCP pool.
Number of Addresses:
Indicates the number of addresses in the DHCP pool.
Gateway:
Select This Unit to use the gateway set on the WAN
interface. Select Othe r to use a different gateway.
Lease Time:
Indicates the expiration time for the IP address
assigned by the DHCP server.
DNS
Server IP Address:
Select WAN Assigne d to use the DNS server IP
addresses assigned on the WAN side. T o use different
DNS servers, select Static, in which case you must
enter the Primary and Se condary IP addresses.
Domain Name:
Apply the same configuration as for Se rver IP
Address.
WINS:
Apply the same configuration as for Se rver IP
Address.
TR-Multi Series
Pitt Meadows, B.C. Canada V3Y 2V4
161616
This document is intended for Public Distributio n
19473 Fraser Way,
3-16
Tranzeo Wireless Technologies
Chapter 3: Configuration
IP Routing
This window is intended for those users who have a strong understanding of IP
routing. Here you can see the System Routes, create your User Routes, and set the
Default Route. Be careful when making changes since misconfiguration could
result in serious network problems and even the loss of functionality.
Interface:
Specify if the interface is WAN or LAN. Select Off to
disable the route.
IP Address:
This is the IP address or network that the packets will
be attempting to access.
Subnet Mask:
Specifies the part of the destination IP that represents
the network address and the part that represents the
host address. Note: 255.255.255.255 represents only
the host entered in the Destination IP field.
Gateway:
Indicates the next hop if this route is used. A gateway
of 0.0.0.0 means there is no next hop and the IP
address matched is directly connected to the router on
the interface specified.
Metric:
This is the number of hops it will take to reach the
destination. A hop occurs each time data passes
through a router from one network to another. If there
is only one router between your network and the
destination network, then the metric value would be 1.
Default Route:
TR-Multi Series
Pitt Meadows, B.C. Canada V3Y 2V4
This option allows you to change the default route of
the radio. Make changes with extreme caution.
171717
This document is intended for Public Distributio n
19473 Fraser Way,
3-17
Tranzeo Wireless Technologies
Chapter 3: Configuration
Quality of Service Configuration (QoS)
In this window you can use the QoS features and set rules to prioritize the traffic.
Uplink Speed:
This is the maximum speed of the uplink (from the
source to the destination). T he order and size of traffic
is determined based on this value.
Dynamic
Fragmentation:
Check to reduce delay for high-priority traffic and
adaptive fragmentation where the fragmentation is
determined by the uplink speed. This feature greatly
improves the gaming and VOIP experience.
Automatic
Classification:
This feature automatically classifies traffic and gives
priority to certain applications. Applications such as
VOIP and gaming are automatically given priority.
Enabled:
Priority:
Name:
Protocol:
Source IP Range:
Source Port Range:
Destination IP Range:
Destination Port
Range:
TR-Multi Series
Pitt Meadows, B.C. Canada V3Y 2V4
Check to activate a rule.
Enter the priority of the rule between 0 and 255.
Enter the name of the rule here.
Enter the protocol number here. Common options are:
0 for ANY, 1 for ICMP, 6 for T CP, and 17 for UDP.
Enter the range of IP addresses on the LAN side where
the rule would apply. To cover all LAN IPs, enter
0.0.0.0. For a single IP, enter the IP in both boxes.
Enter the range of ports on the LAN side where the
rule would apply. To cover all ports, enter 0. For a
single port, enter this port in both boxes.
Enter the range of IP addresses on the WAN side
where the rule would apply.
Enter the range of ports on the WAN side where the
rule would apply.
181818
This document is intended for Public Distributio n
19473 Fraser Way,
3-18
Tranzeo Wireless Technologies
Chapter 3: Configuration
Port Forwarding
This feature allows the radio to forward requests for certain ports to devices
behind a router. For example, you have a web server on a private IP that you want
to be accessible to the world. You can forward all requests on port 80 to
192.168.1.2. For this to work, you have to change the management port of the
radio from port 80 on the Network Configuration window.
In this window, you can create, edit, delete, and manage rules for port forwarding.
A list of port forwarding rules appears at the bottom.
Enable Port
Forwarding:
Forward Rule ID:
Edit / Delete:
Enabled / Disabled:
External Port:
Internal Port:
Internal Address:
Protocol:
Pitt Meadows, B.C. Canada V3Y 2V4
Enter the rule ID here to retrieve its information.
Click to modify or remove the selected rule.
Activate or deactivate the selected rule.
Enter the port to which requests will be forwarded.
Enter your port here.
Enter your IP address.
Select the protocol used for this rule.
New:
Click to create a new rule. Fields will be cleared.
Add:
After creating a rule, click this button to include the
new rule in the Port Forwarding Rules list.
Update:
TR-Multi Series
Click to apply rules from the Rules list.
Click to apply changes after editing or deleting a rule.
191919
This document is intended for Public Distributio n
19473 Fraser Way,
3-19
Tranzeo Wireless Technologies
Chapter 3: Configuration
Port Filtering
This feature allows the radio to block requests to and from devices behind the
router. A list of the devices filtered appears at the bottom of the window.
Enable Port Filtering:
WAN / LAN:
Filter Rule ID:
Click to apply the rules enabled from the Filter list.
Select the network.
Enter the filter rule ID here to retrieve its information.
Edit / Delete:
Click to modify or eliminate the selected filter.
Allow / Deny:
The rule can either allow or deny ports.
New:
Click to create a new filter. Fields will be cleared and
you may enter the information for the new filter.
Add:
After creating a filter, click this button to include the
new filter in the Filter list.
Source IP Range:
Destination IP Range:
Source Port Range:
Enter the range of IP addresses on the LAN side where
the rule would apply.
Enter the range of IP addresses on the WAN side
where the rule would apply.
Enter the range of ports on the LAN side where the
rule would apply.
Destination Port
Range:
Enter the range of ports on the WAN side where the
rule would apply.
ICMP Type:
This allows you to block certain types of ICMP as a
prevention against port scanning and some viruses.
Protocol:
Update:
TR-Multi Series
Pitt Meadows, B.C. Canada V3Y 2V4
Select the protocol used for this rule.
Click to apply changes after editing or deleting a filter.
202020
This document is intended for Public Distributio n
19473 Fraser Way,
3-20
Tranzeo Wireless Technologies
Appendix A
Appendix A: Grounding and Lightning
Protection Information
What is a proper ground?
This antenna must be grounded to a proper earth ground. According to the
National Electrical Code Sections 810-15s and 810-21, the grounding conductor
shall be connected to the nearest accessible locations of the following:
•
•
•
•
•
•
The building or structure grounding electrode
The grounded interior metal water piping system
The power service accessible means external to enclosure
The metallic power service raceway
The service equipment enclosure
The grounding electrode conductor
Why is coiling the LMR or Cat 5 bad?
The myth is that lighting follows the path of least resistance. It actually follows the
path of least impedance. Coiling cables creates an air-wound transformer, which
lowers the impedance. T his means you are in fact making your radios a more
appealing target for surges.
What standard does Tranzeo Wireless equipment meet?
This radio exceeds International Standard IEC 61000-4-5 when properly
grounded. For a copy of the full testing report, see Report Number T RL090904 Tranzeo Surge Protection board located on the Tranzeo website
(www.tranzeo.com).
Is lightning damage covered by the warranty?
No. Lightning is not covered by the warranty. If you follow the instructions, your
chances of lightning damage are greatly reduced, but nothing can protect a radio
from a direct lightning strike.
TR-Multi Series
Pitt Meadows, B.C. Canada V3Y 2V4
111
This document is intended for Public Distributio n
19473 Fraser Way,
A-1
Tranzeo Wireless Technologies
Appendix A
Where to ground the device?
This radio must be grounded at the pole and at the POE. This is because the radio
is between the exterior antenna and the POE ground. See the examples below.
Grounded Radio
A grounded radio causes the surge to pass directly to ground, bypassing the radio.
Antenna
Radio
POE
Ground
Ungrounded Radio
An ungrounded radio causes the surge to pass through the radio. In this case, the
radio most likely will be damaged.
Antenna
Radio
POE
Ground
TR-Multi Series
Pitt Meadows, B.C. Canada V3Y 2V4
222
This document is intended for Public Distributio n
19473 Fraser Way,
A-2
Tranzeo Wireless Technologies
Appendix A
Grounded POE
In this case, the surge will be picked up by the Cat 5 cable and since the POE is
grounded, the route for the surge is through the POE to ground.
Mounting Pole
POE
Ground
Cat 5 Cable
Ungrounded POE
In this case, the surge will be picked up by the Cat 5 cable and since the POE is
not grounded, the route for the surge is through the radio to the antenna, and out
through the building.
Mounting Pole
POE
Cat 5 Cable
TR-Multi Series
Pitt Meadows, B.C. Canada V3Y 2V4
333
This document is intended for Public Distributio n
19473 Fraser Way,
A-3
Tranzeo Wireless Technologies
Appendix B
Appendix B: Product Specification
Features
Standard
802.11a/b
Frequency Range
2412 – 2462 MHz; 5280 – 5320 MHz; 5745 – 5825 MHz
Radio Mode
Customer Premise Equipment
Data Range & Modulation
11Mbps & 5.5Mbps CCK, 2Mbps DQPSK, 1 Mbps DBPSK
Communication Method
Half-Duplex
Transmit Power
23 dBm (2.4 GHz), 17 dBm (5 GHz)
Receiv er Sensitivity
-90dBm @ 11Mbps (2.4GHz), -76dBm @ 54 Mbps (5 GHz)
Polarization
Horizontal or Vertical
Antennas
Wind Load (N)
Model
TR-Multi-N
TR-Multi-2
Type
N-Connector
16dBi (2.4 GHz),
20dBi (5 GHz) Panel
Beamwidth
100 mph 125 mph
105
165
182
285
Horizontal
Vertical
N/A
18.2° (2.4 GHz )
10.5° (5 GHz)
N/A
18.2° (2.4 GHz )
10.5° (5 GHz)
Management
Remote Configuration
Based on IP Address
Device Management
Windows Utility, Web-Based Management, SNMP (MIB-II and
80211 mib compliant)
Protocol Supported
TCP/IP
Security
40 bits and 128 bits WEP encryption, Access Control address
filter (MAC), WPA encryption
Ethernet Connector
10/100 BaseT (wate r tight RJ-45)
Operating Temperature
-65°C to +60°C
Warranty
1 year depot
TR-Multi-N
13" X 10-1/8" (radio only)
TR-Multi-2
16" X 14-1/4" (radio only)
Dimensions
Power Supply
AC Wall Plug
Input: 120V 60Hz
Output: 18V, 1000mA
AC Wall Plug
Input: 120V 60Hz
Output: 24V, 1000mA
Standard
Optional
Specifications are subject to change without notice.
Subject to local regulations.
TR-Multi Series
Pitt Meadows, B.C. Canada V3Y 2V4
111
This document is intended for Public Distributio n
19473 Fraser Way,
B-1
Tranzeo Wireless Technologies
Appendix C
Appendix C: Protocol List
Dec
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
Keyword
HOPOPT
ICMP
IGMP
GGP
IP
ST
TCP
CBT
EGP
IGP
BRM
NVP-II
PUP
ARGUS
EMCON
XNET
CHAOS
UDP
MUX
DCN-MEAS
HMP
PRM
XNS-IDP
TRUNK-1
TRUNK-2
LEAF-1
LEAF-2
RDP
IRTP
ISO-TP4
NETBLT
MFE-NSP
MERIT-INP
SEP
3PC
IDPR
XTP
DDP
IDPR-CMTP
TP++
IL
IPv6
SDRP
IPv6-Route
IPv6-Frag
IDRP
RSVP
GRE
MHRP
BNA
ESP
Protocol
IPv6 Hop-by-Hop Option
Internet Control Message
Internet Group Management
Gateway-to-Gateway
IP in IP (encapsulation)
Stream
Transmission Control
CBT
Ex terior Gateway Protocol
private interior gateway
BBN RCC Monitoring
Network Voice Protocol
PUP
ARGUS
EMCON
Cross Net Debugger
Chaos
User Datagram
Multiplex ing
DCN Measurement
Host Monitoring
Packet Radio Measurement
XEROX NS IDP
Trunk-1
Trunk-2
Leaf-1
Leaf-2
Reliable Data Protocol
Internet Reliable Transaction
ISO Transport Class 4
Bulk Data Transfer
MFE Network Services
MERIT Internodal Prot ocol
Sequential Exchange
Third Party Connect
Inter-Domain Policy Routing Protocol
XTP
Datagram Delivery
IDPR Cont rol Message Transport P roto
TP++ Transport Protocol
IL Transport Protocol
Ipv6
Source Demand Routing
Routing Header for IPv6
Fragment Header for IPv6
Inter-Domain Routing
Reservation Protocol
General Routing Encapsulation
Mobile Host Routing Protocol
BNA
Encap Security Payload for IPv6
TR-Multi Series
Pitt Meadows, B.C. Canada V3Y 2V4
Dec
51
52
53
54
55
56
Keyword
AH
I-NLSP
SWIPE
NARP
MOBILE
TLSP
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
SKIP
IPv6-ICMP
IPv6-NoNx t
IPv6-Opts
CFTP
SAT-EXPAK
KRYPTOLAN
RVD
IPPC
SAT-MON
VISA
IPCV
CPNX
CPHB
WSN
PVP
BR-SAT-MON
SUN-ND
WB-MON
WB-EXPAK
ISO-IP
VMTP
SECURE-VMTP
VINES
TTP
NSFNET-IGP
DGP
TCF
EIGRP
OSPFIGP
Sprite-RPC
LARP
MTP
AX.25
IPIP
MICP
SCC-SP
ETHERIP
ENCAP
GMTP
Protocol
Authentication Header for IPv6
Integrated Net Layer Security
IP with Encryption
NBMA Address Resolution
IP Mobility
Transport Layer Security using
Kryptonet key management
SKIP
ICMP for IPv6
No Nex t Header for IPv6
Destination Options for IPv6
any host internal protocol
CFTP
any local network
SATNET and Backroom EXPAK
Kryptolan
MIT Remote Virtual Disk
Internet Pluribus Packet Core
any distributed file system
SATNET Monitoring
VISA Protocol
Internet Packet Core Utility
Computer P rotocol Network Ex ecutive
Computer P rotocol Heart Beat
Wang Span Network
Packet Video Protocol
Backroom SATNET Monitoring
SUN ND P ROTOCOL-Temporary
WIDEBAND Monitoring
WIDEBAND EXPAK
ISO Internet Protocol
VMTP
SECURE-VMTP
VINES
TTPord Protocol
NSFNET-IGP
Dissimilar Gateway Protocol
TCF
EIGRP
OSPFIGP
Sprite RPC Prot ocol
Locus Address Resolution
Multicast Transport Protocol
AX.25 Frames
P-within-IP Encapsulation
Mobile Internetworking Control
Semaphore Communications Sec.
Ethernet-within-IP Encapsulation
Encapsulation Header
any private encryption scheme
GMTP
111
This document is intended for Public Distributio n
19473 Fraser Way,
C-1
Tranzeo Wireless Technologies
Appendix C
Dec
Keyword
Protocol
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
IFMP
PNNI
PIM
ARIS
SCPS
QNX
A/N
IPComp
SNP
Compaq-Peer
IPX-in-IP
VRRP
PGM
Ipsilon Flow Management
PNNI over IP
Protocol Independent Multicast
ARIS
SCPS
QNX
Active Networks
IP Payload Compression
Sitara Networks Protocol
Compaq Peer Protocol
IPX in IP
Virtual Router Redundancy
PGM Reliable Transport
any 0-hop protocol
Layer Two Tunneling Protocol
D-II Dat a Ex change (DDX)
Interactive Agent Transfer
Schedule Transfer Protocol
SpectraLink Radio Protocol
UTI
L2TP
DDX
IATP
STP
SRP
UTI
TR-Multi Series
Pitt Meadows, B.C. Canada V3Y 2V4
Dec
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138-252
253
254
255
Keyword
Protocol
SMP
Simple Message Protocol
SM
SM
PTP
Performance Transparency
ISSIS
ISIS over IPv4
FIRE
CRTP
Combat Radio Transport
CRUDP
Combat Radio User Datagram
SSCOPMCE
IPLT
SPS
Secure Packet Shield
PIPE
Private IP Encapsulation within IP
SCTP
Stream Cont rol Transmission
FC
Fibre Channel
RSVP-E2E-IGNORE
Mobility header
UDPLite
MPLS-in-IP
Unassigned
Use for ex perimentation and testing
Use for ex perimentation and testing
Reserved
222
This document is intended for Public Distributio n
19473 Fraser Way,
C-2
Tranzeo Wireless Technologies
Appendix D
Appendix D: Common TCP Ports
Visit http://www.iana.org/assignments/port-numbers for a full list of well known
port numbers.
TR-Multi Series
Pitt Meadows, B.C. Canada V3Y 2V4
Keyword
ECHO
SYSTAT
QOTD
MSP
Por t
11
17
18
Descr iption
Echo
Active Users
Quote of t he day
Message Send Protocol
FTP-DATA
FTP
TELNET
SMTP
NAME
BOOTPS
BOOTPC
TFTP
WWW
KERBEROS
POP3
NNTP
NFS
SIP
20
21
23
25
42
67
68
69
80
88
110
119
2049
5060, 5061
File Transfer (Dat a Channel )
File Transfer (Control)
Telnet
Simple Mail Transfer
TCP Nameserver
Bootstrap Protocol Server
Bootstrap Protocol Client
Trivial File Transfer
World Wide Web
Kerberos
TCP post office
USENET
Network File System
SIP
111
This document is intended for Public Distributio n
19473 Fraser Way,
D-1


---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.3
Linearized                      : No
Page Count                      : 42
Producer                        : GPL Ghostscript 8.15
Create Date                     : 2006:07:17 16:45:00
Modify Date                     : 2006:07:17 16:45:00
Title                           : Multipoint_UG_v1_170706.pub
Creator                         : PScript5.dll Version 5.2
Author                          : Cecilia Vallejo

EXIF Metadata provided by EXIF.tools