Traxxas LP TRX1018 Traxxas Link wireless module User Manual 3

Traxxas LP Traxxas Link wireless module Users Manual 3

UserManual.wiki >

TRX1018 User Manual >

Contents

Users Manual-3

TRAXXAS • 11 Note: The following instructions are for Mode 2 transmitters (throttle stick on the left, ight control stick on the right).Sport ModeFor those that want to go beyond simply directing Āton in the sky and explore what it’s like to actually take more control and ﬂy, Āton is equipped with Sport Mode. Sport (Fast) Mode uses the full capability of the 6-axis ﬂight control system (auto leveling) for high-speed sport ﬂying. Altitude hold is disabled and both altitude and throttle are controlled by the throttle stick (left stick, Mode 2). Sport Mode also enables trick functions. To enter Sport Mode, the Āton should be powered on and disarmed. Press to click the ﬂight control stick (right stick) once to toggle the Āton into Sport Mode. The transmitter will beep 2 times, the green LED will begin ﬂashing, and the LCD will display FAST. Performing tricksIn Sport (Fast) Mode, Āton can perform automated expert ﬂips and rolls when you press the AUX1 button, and then enter a quick stick command in the chosen direction. Do not attempt these ﬂight tricks until you are able to ﬂy conﬁdently in Sport Mode. Choose an area that will provide a soft landing and maintain enough altitude to allow room to recover control as you practice ﬂipping the model. The number of ﬂips and rolls performed can be set using the Traxxas Flight Link App (see page 14 for more information). There are also menu functions in the transmitter that allow you to customize the settings. Refer to the instructions online for using the transmitter menu.Note: Always remove camera frame and landing gear BEFORE attempting ﬂight tricks.AIR BRAKESIf you lose control of Āton at any point, press and hold the Air Brakes button and Āton will come to a stop and hover in place. When you are ready, release the Air Brakes button and continue ﬂying in the currently selected mode (Film, Sport, or Expert). RETURN TO HOMEThe Return to Home button may be pressed at anytime to stabilize Āton and return it to you. You may cancel return to home by pressing and releasing the Air Brakes button. Āton will then be ﬂying in Film Mode under your control. ADVANCED: CHANGING MODES DURING FLIGHTAdvanced pilots may ﬁnd it helpful to be able to change modes during ﬂight. For example, if you are ﬂying in Sport Mode, use Return to Home, and then cancel return to home. Āton will then be ﬂying in Film Mode. You can switch back to Sport Mode and continue ﬂying by pressing and holding the Air Brakes button, and then pressing (clicking) the ﬂight control stick to toggle through the modes...one click for Sport Mode, 2 clicks for Expert Mode. Release the Air Brakes button to continue ﬂying in the selected mode. Click Once FlashingSelecting Sport Mode (while disarmed)x1x1Front and Back FlipsDiagonal Front and Back FlipsSide Flips1.1.1.2.2.2.Press AUX1Press AUX1Press AUX1Front FlipLeft Flip Right FlipDiagonal Front RightDiagonal Front Left Diagonal Back RightBack FlipDiagonal Back Left

12 • TRAXXASExpert ModeIn Expert Mode, the 6-axis ﬂight control system (auto leveling) is disabled, allowing the pilot to have full control over all aspects of ﬂight. Expert Mode is truly for experts. If you ﬁnd yourself ﬂying Āton out of control, press and hold the Air Brakes button or press the Return to Home button. When ﬂying in Expert Mode, move the ﬂight stick toward the highest side of the helicopter (left or right) to level it. Choose a location that allows you to ﬂy over grass or another soft surface.From Film Mode with the helicopter landed and disarmed, click the ﬂight stick twice to activate Expert Mode. The transmitter will beep 3 times, the green LED will begin double ﬂashing, and the LCD will display EXPERT. WARNING: This mode is intended for expert level pilots only! For more information on how to perform expert tricks and ﬂips and learn how to access the menu and advanced controls, visit Traxxas.com for additional details and instructions.CARING FOR YOUR HELICOPTER• After each ﬂight and immediately after any crash, inspect your model for worn or damaged parts. If required, parts are available from your local Traxxas hobby dealer or at Traxxas.com. For a complete parts list and exploded view of your model, refer to the Service and Support Guide in this manual.• When not in use, store your model in its original packaging with the batteries removed from the transmitter and helicopter.• If you do not plan to ﬂy your model for a week or more, store the battery approximately 50% charged to maintain battery performance and life. To achieve a 50% charge, ﬂy the model until the battery requires recharging. Charge the battery for half the time typically required to fully charge the battery or ﬂy the model until a 50% charge remains.WARNING! Do not store or attempt to charge a swollen or damaged battery! See “Safety Precautions” on page 5 for more information on LiPo batteries.ROTOR BLADE INSTALLATIONThe Āton’s rotor blades are not identical. Each blade is labeled with an A or B. When installing replacement rotor blades, be certain to install the rotor blades with the corresponding A or B for each of the legs (A or B labels for the legs are molded on the LED lens). The helicopter will not ﬂy if the rotor blades are not installed in the proper locations.LED STATUS BARThe LED Status Bar on the model is your ﬂight information center. The chart below deﬁnes common Status Bar messages.BAABFrontClick Twice(Click again to return to Film Mode)Double FlashingSelecting Expert Mode (while disarmed)x2x2Home Button Fast Flashing: Helicopter has landed away from set home locationArm/Disarm Button Flashing: Helicopter is disarmedPower Indicator Flashing: Low batteries in transmitter; land immediatelyHome Button Slow Flashing: Helicopter returning to home landing locationTRANSMITTER CODESPower GPS Home InfoOn(Working /Available)Linked to transmitterGPS signal acquiredHome location setAll systems normal, Ready to FlyO(Not Available)Battery disconnected –Return to Home not availableBattery disconnectedSlow Flashing(Active)Looking for transmitter signalSearching for satellitesReturn to Home active Low batteryFast Flashing(User Action Needed)Transmitter signal lost –Helicopter has landed away from the set home location–Tone/Beep Pattern Name DescriptionLow-mid-high tone Return to Home Return to Home button pressedLow-mid-high tone + 1 beepOut of Radio Control Range Radio signal loss or interferenceLow-mid-high tone + 2 beeps Geofence BreachĀton has own beyond GPS-controlled boundary (geofence)Low-mid-high tone + 3 beepsLow-Voltage FailsafeTransmitter or helicopter battery is nearly discharged.RETURN TO HOME REFERENCE GUIDE

TRAXXAS • 13 TROUBLESHOOTING GUIDE• The helicopter can’t ﬁnd a satellite GPS signal.1. Certain surfaces can cause signal interference between the helicopter and GPS satellites. Move the helicopter to different launch locations and away from buildings, parked cars, and other obstructions until a signal can be established. We don’t recommend ﬂying without a GPS signal.• The transmitter and the helicopter are on, but the helicopter won’t ﬂy. 1. The model is not armed or has timed-out. See step 6 of the “Flying Your Model” section to arm your helicopter.• The helicopter does not perform a trick when the AUX1 button is pressed and then a stick command is given.1. The transmitter is not in Fast Mode. See the “Flight Modes” section.• The helicopter landed by itself, and now the throttle will not respond.1. The helicopter battery needs to be recharged (low voltage).• The LED is blinking on the transmitter, and the transmitter will not control the model.1. The transmitter is in binding mode. Conﬁrm that the helicopter is powered on and the transmitter is in binding mode (blinking LED, LCD displays rotating segments). Move the transmitter to within one foot of the helicopter. The transmitter and helicopter should bind (indicated by a tone from the transmitter, solid green LED on the transmitter, solid green Power and Info Status LED on the helicopter, and the Disarmed Flight Screen on the transmitter LCD).2. There was a problem with the binding process. Power down the transmitter and the helicopter, and then power them on again (transmitter ﬁrst, then helicopter). The transmitter and helicopter should bind (indicated by a tone from the transmitter, solid green LED on the transmitter, solid green Power and Info Status LEDs on the helicopter, and the Disarmed Flight Screen on the transmitter LCD).3. The model is not armed or has timed-out. To arm your helicopter, see step 6 of the “Preparing for Flight” section on page 6. • The transmitter settings have been adjusted incorrectly for optimal ﬂight.1. Return the transmitter to the default settings.A. Ensure the transmitter is off.B. Press and hold the AUX2 button and the Menu Down button.C. While holding both buttons, turn the transmitter on.D. Continue holding both buttons for 3 seconds until the transmitter beeps. Release both buttons.E. The transmitter is reset and is in bind mode (blinking LED, LCD displays rotating segments).F. Conﬁrm that the helicopter is powered on and is in binding mode (Info Status LED blinking fast green).G. Move the transmitter to within one foot of the helicopter. The transmitter and helicopter should bind (indicated by a tone from the transmitter, solid green LED on the transmitter, solid green Power and Info Status LEDs on the helicopter, and the Disarmed Flight Screen on the transmitter LCD).• The helicopter battery is fully charged and the rotor blades are spinning, but the helicopter will not lift off.1. The rotor blades have been installed incorrectly. See “Rotor Blade Installation.”• The helicopter does not ﬂy as expected or the helicopter performs erratically in Film Mode.1. The helicopter has lost the GPS signal. Fly the helicopter to a suitable ﬂying area with a clear view of the sky to reestablish the GPS signal.• The helicopter does not ﬂy as expected or the helicopter performs erratically in Fast or Expert Mode.1. The accelerometer or ﬂight compass needs to be reset. Go to Traxxas.com for additional information and instructions or call the Traxxas Technical Support Line toll-free at: 1-888-TRAXXAS (1-888-872-9927).

Navigation menu