TriGem Computer N3400NILE NOTEBOOK P.C. User Manual AV N3400 User s Guide USc00
TriGem Computer, Inc NOTEBOOK P.C. AV N3400 User s Guide USc00
Users Manual
| Download: |  |
| Mirror Download [FCC.gov] | |
| Document ID | 1066435 |
| Application ID | /tVS2xNmWd4aXTfY+dzrOA== |
| Document Description | Users Manual |
| Short Term Confidential | No |
| Permanent Confidential | No |
| Supercede | No |
| Document Type | User Manual |
| Display Format | Adobe Acrobat PDF - pdf |
| Filesize | 97.05kB (1213122 bits) |
| Date Submitted | 2009-02-10 00:00:00 |
| Date Available | 2009-02-12 00:00:00 |
| Creation Date | 2009-01-10 10:35:02 |
| Producing Software | Acrobat Distiller 9.0.0 (Windows) |
| Document Lastmod | 2009-01-13 11:50:23 |
| Document Title | AV N3400 User's Guide_USc00ÃŽÃõ¿ë |
| Document Creator | QuarkXPress3.3K: LaserWriter 8 KH-8.7 |
| Document Author: | momo |
N3400 Series User’s Guide Space Saving Contemporary Design Regulations Information FCC-B Radio Frequency Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures : • Reorient or relocate the receiving antenna. • Increase the separation between the equipment and receiver. • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. • Consult the dealer or an experienced radio TV technician for help. Note ✓ The changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. ✓ Shield interface cables and AC power cord, if any must be used in order to comply with the emission limits. Before You Start FCC Conditions This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions : 1. This device may not cause harmful interference. 2. This device must accept any interference received, including interference that may cause undesired operation. FCC Radlo Frequency Interference Requlrements 1. This device has no Ad-hoc capability for 5250 ~ 5350 and 5470 ~ 5725 MHz. 2. This device is restricted to INDOOR USE due to its opration in the 5.15 to 5.25GHz frequency range. FCC requires this product to be used indoors for the frequency range 5.15 to 5.25GHz to reduce the potential for harmful interference to co-channel of the Mobile Satellite Systems. High power radars are allocated as primary user of the 5.25 to 5.35GHz and 5.65 to 5.85GHz bands. These radar stations can cause interference with and / or damage this device. RF exposure warning The equipment complies with FCC RF exposure limits set forth for an uncontrolled environment. The equipment must not be co-located or operating in conjunction with any other antenna or transmitter. SAR Value : 0.561 W/Kg Before You Start ii Safety Guideline for Using Lithium Battery (Danish) ADVARSEL! Lithiumbatteri --- Eksplosionsfare ved fejlagtig håndtering. Udskiftning må kun ske med batteri af same fabrikat og type. Levé det brugte batteri tilbage til leverandøren. (Deutsch) VORSICHT: Explosionsgefahr bei unsachgemäßem Austausch der Batterie. Ersatz nur durch denselben oder einen vom Hersteller empfohlenen gleich-wertigen Typ. Entsorgung gebrauchter Batterien nach Angaben des Herstellers. (English) CAUTION: Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type recommended by the equipment manufacturer. Discard used batteries according to manufacturers instructions. (Finnish) VAROITUS: Paristo voi räjähtää, jos se on virheellisesti asennettu. Vaihda paristo ainoastaan valmistajan suosittelemaan tyyppiin. Hävitä käytetty paristo valmistajan ohjeiden mukaisesti. (French) ATTENTION: II y a danger dex;losion sil y a remplacement incorrect de la batterie. Remplacer uniquement avec une batterie du meme type ou dun type équivalent recommandé par le constructeur. Mettre au rebut les batteries usages conformément aux instructions du fabricant. (Norwegian) ADVARSEL: Eksplosjonsfare ved feilaktig skifte av batteri. Benytt same batteritype eller en tilsvarende type anbefalt av apparatfabrikanten. Brukte batterier kasseres I henhold til fabrikantens instruksjoner. (Swedish) VARNING: Explosionsfara vid felaktigt batteribyte. Använd samma batterityp eller en ekvivalent typ som rekommenderas av apparattillverkaren. Kassera använt batteri enligt fabrikantens instruction. Before You Start iii Optical Device Drive Notice CAUTION ✓ This appliance contains a laser system and is classified as a “CLASS 1 LASER PRODUCT.” To use this model properly, read the instruction manual carefully and keep this manual for your future reference. In case of any trouble with this model, please contact your nearest “AUTHORIZED service station.” To prevent direct exposure to the laser beam, do not try to open the enclosure. Macrovision Notice This product incorporates copyright protection technology that is protected by U.S. patents and other intellectual property rights. Use of this copyright protection technology must be authorized by Macrovision, and is intended for home and other limited viewing uses only unless otherwise authorized by Macrovision. Reverse engineering or disassembly is prohibited. Before You Start iv Safety Instructions 1. Read the safety instructions carefully and thoroughly. 2. Save this User Guide for possible use later. 3. Keep this equipment away from humidity and high temperature. 4. Lay this equipment on a stable surface before setting it up. 5. The openings on the enclosure are used for air convection and to prevent the equipment from overheating. Do not cover the openings. 6. Make sure that the power voltage is within its safety range and has been adjusted properly to the value of 100~240V before connecting the equipment to the power inlet. 7. Place the power cord in a way that people are unlikely to step on it. Do not place anything on the power cord. 8. Always unplug the power cord before inserting any add-on card or module. 9. All cautions and warnings on the equipment should be noted. 10. If any of the following situations arises, get the equipment checked by a service personnel: ✓ The power cord or plug is damaged. ✓ Liquid has penetrated into the equipment. ✓ The equipment has been exposed to moisture. ✓ The equipment has not worked well or you can not get it work according to Users Manual. ✓ The equipment was dropped and damaged. ✓ The equipment has obvious signs of breakage. Before You Start 11. Never pour any liquid into the opening that could damage the equipment or cause an electrical shock. 12. Do not leave the equipment in an unconditioned environment with a storage temperature of 60°C (140°F) or above, which may damage the equipment. 13. To prevent explosion caused by improper battery replacement, use the same or equivalent type of battery recommended by the manufacturer only. Before You Start vi WEEE Statement Before You Start vii Trademarks All trademarks are the properties of their respective owners. ✓ Microsoft is a registered trademark of Microsoft Corporation. Windows98/ME, 2000/XP are registered trademarks of Microsoft Corporation. ✓ PCMCIA and CardBus are registered trademarks of the Personal Notebook Memory Card International Association. Release History Version Revision Note Date 1.1 Second Release 01, 2009 Before You Start viii Table of Content Before You Start Regulations Information Charging the Battery Pack 14 iii Chapter 3 Using the Notebook Computer Optical Device Drive Notice iv Adjusting the LCD Screen Display 16 Macrovision Notice iv The Notebook’s Hot Key Controls 18 Safety Instructions The TouchPad 19 Safety Guideline for Using Lithium Battery WEEE Statement vii Power Saving Modes 22 Trademarks viii Removing the Battery Pack 23 Release History viii Adjusting the Brightness 26 Using the Windows 27 Chapter 1 Introduction Unpacking Introduction Chapter 4 Desktop Operation Audio 32 Chapter 5 Internet Connection Chapter 2 Getting Started Connecting to a Power Source 10 Turning On Your Notebook Computer 11 Operating on Battery Power 11 Installing and Removing the Battery Pack 12 Using a Wired LAN for Connection to the Internet 35 Using Wireless LAN Network for Connection to the Internet 36 Before You Start ix Chapter 6 Running BIOS Setup Chapter 9 Specification Entering the BIOS Setup Screen 38 CPU 59 Leaving the BIOS Setup Screen 38 Memory 59 BIOS Action Keys 39 Core Logic 59 Modifying the BIOS Settings 40 VGA 60 Audio Codec 60 Card reader (4 in 1) 60 45 LAN Controller 61 Display Settings 45 Wireless LAN (Optional) 61 Color Correction 46 Keyboard 61 Hot Keys 46 Pointing Device 61 LCD 62 HDD 62 Chapter 7 VGA Utilities Display Devices Chapter 8 Troubleshooting Audio Problems 50 Hard Disk Problems 51 Display Problems 52 Keyboard and Mouse Problems 53 CMOS Battery Problem 54 Memory Problems 54 PC Card Problems 55 Performance Problems 56 USB2.0 Problems 57 Battery Pack 62 AC-Adapter 62 BIOS 63 Physical Outline 63 Camera module support (Optional) 63 Before You Start 1 Chapter Introduction Chapter 1 Introduction Unpacking First, unpack the notebook from the shipping carton and check all items carefully. If any item is damaged or missing, please contact your local dealer immediately. Keep the box and packing materials in case you need to ship the unit in for service in the future. The package should contain the following items: ✓ Notebook Computer ✓ Quick Start Guide ✓ All-in-one application disk, containing the drivers, utilities, and factory recovery image. ✓ High-capacity Li-ion battery pack ✓ AC adapter and power cord ✓ Phone cable/Phone jack (optional) ✓ Notebook carry bag (optional) These accessories listed above may change without notice. Chapter 1 Introduction Introduction Welcome to the Notebook PC Congratulations on your purchase of the Notebook PC. Your Notebook features the latest advances in portable computing technology. The Notebook’s modular design provides maximum expandability without compromising portability. Getting to Know Your Computer Opening the LCD Panel WARNING ✓ To avoid damage to the display panel: 1. Try not to slam the display upon closing it. 2. Try not to place any object on top when it is closed or open. 3. Be sure the system is turned off or in suspend mode before you close the display panel. Chapter 1 Introduction With the LCD screen open, you will see several features important for operating your Notebook computer. Front View To open, lift the top cover (LCD Panel). The image of the top-open view and descriptions below will help you to get familiarized with the main features of your notebook. WARNING ✓ Do not place any heavy objects on the top of notebook. This may damage the display. Chapter 1 Introduction 1. Integrated webcam 2. Built-in microphone 3. LCD display 4. Power button / Power Indicator • Press momentarily to turn on the system. • Press and hold for at least 4 seconds to turn off the system. • Persistent green light indicates the Power is ON 5. Keyboard 6. Touchpad 7. Touchpad left / Right buttons Chapter 1 Introduction Left Views 1. Power jack (DC-in) 2. Ventilation grill 3. USB connector 4. 4-in-1 card reader The 4-in-1 Card Reader supports SD Card, MMC Card, MS and MS-Pro Card. Chapter 1 Introduction Right View 1. Microphone jack 2. Headphone/Speaker/SPDIF jack 3. USB connectors 4. Network connector (LAN) Note ✓ When using a LAN, please use an EMI Shielding Cable to minimize an inteference when transmitting. 5. VGA port 6. Kensington lock Chapter 1 Introduction Bottom View 1. Ventilation grill 2. Hard disk drive / Battery pack / Main memory cover 3. Integrated speakers Chapter 1 Introduction Chapter Getting Started Chapter 2 Getting Started Connecting to a Power Source Connecting the AC Adapter A universal AC adapter is provided to supply your computer with power and also charge the computer’s battery pack. The adapter’s AC input voltage can range anywhere from 100 to 240 volts, covering the standard voltages available in almost every country. To connect the computer to an external power source: WARNING ✓ Do not use inferior extension cords as this may result in damage to your Notebook. The Notebook comes with its own AC adapter. Do not use a different adapter to power the computer and other electrical devices. Whenever possible, keep the AC adapter plugged into the Notebook and an electrical outlet to recharge the battery. WARNING ✓ Never turn off or reset your Notebook while the hard disk is in use and the CD-ROM status icon is lit; doing so can result in loss or destruction of your data. Always wait at least 5 seconds after turning off your Notebook before turning it back on; turning the power on and off in rapid succession can damage the Notebook’s electrical circuitry. Chapter 2 Getting Started 10 Turning On Your Notebook Computer Turn on your Notebook by pressing the power button. Hold the button down for a second or two and release. The PowerOn Self Test (POST) runs automatically. After the POST is completed, the computer reads the operating system from the hard disk drive into computer memory (this is commonly referred to as “booting” a computer). If your OS (Operating System such as Windows Vista.... etc) is installed, it should start automatically. To turn the Notebook off, save your work and close all open applications, click on Start, then Shut Down and select Shut down the computer and click "Yes" or press the power button for 4-6 seconds. Operating on Battery Power Your computer comes with a rechargeable battery pack that lets you operate the computer without an external power source. When the battery pack is the charged, you can operate the computer under the following conditions: • The battery pack is installed and no AC adapter is plugged in WARNING ✓ Only use batteries that are approved by an authorized dealer. All batteries are not the same and therefore should not be treated as such. Using the wrong battery could cause serious damage to your computer and yourself through toxic emissions. CAUTION ✓ Danger of explosion if battery is incorrectly replaced. Replace only with same or equivalent type recommended by the manufacturer. Discard used batteries according to the manufacturer’s instructions or local laws. Chapter 2 Getting Started 11 Installing and Removing the Battery Pack Removing the Battery Pack Chapter 2 Getting Started 12 Installing the Battery Pack Chapter 2 Getting Started 13 Charging the Battery Pack The installed battery pack charges automatically any time the computer is connected to the AC adapter and an external power source. It is a good idea to occasionally discharge the battery pack fully to preserve its operating performance. Chapter 2 Getting Started 14 Chapter Using the Notebook Computer Chapter 3 Using the Notebook Computer 15 Adjusting the LCD Screen Display The LCD screen display can be adjusted by the following key combinations. KEYS FUNCTIONS Fn + F5 LCD Panel Off Fn + F6 Changes Display Mode: LCD-only, CRT-only and LCD & CRT. Fn + F7 Increases the brightness level. Fn + F8 Decreases the brightness level. LCD Care LCD screens are delicate devices that need careful handling. Please pay attention to the following precautions: • When you are not using the computer, keep the LCD screen closed to protect it from dust. • If you need to clean your LCD screen, use a soft tissue to gently wipe the LCD surface. • Do not put your fingers or sharp objects directly on the surface and never spray cleaner directly onto the display. • Do not press on, or store any objects on the cover when it is closed. Doing so may cause the LCD to break. Chapter 3 Using the Notebook Computer 16 External CRT Display You can hook up an external monitor through the 15-pin CRT connector. Three configurations are available: • LCD only • CRT only • Simultaneous display of the LCD screen and CRT monitor You can switch between these display configurations by pressing the key combination [Fn] + [F6]. Chapter 3 Using the Notebook Computer 17 The Notebook’s Hot Key Controls Function Keys (Quick Keys) Graphic Symbol Action System Control Fn + F1 Enters Suspend Mode. Fn + F2 Bluetooth function On/Off. Fn + F3 Wireless LAN function On/Off. Fn + F4 Eable/Disable the Touchpad Fn + F5 LCD Panel Screen On/Off. Fn + F6 Changes Display Mode: LCD-only, CRTonly and LCD & CRT. Fn + F7 Increases the brightness level. Fn + F8 Decreases the brightness level. Fn + F9 Mute/Unmute Audio Fn + F10 Increases the speaker volume. Fn + F11 Decreases the speaker volume. Fn + F12 Enable/Disable the Web camera Chapter 3 Using the Notebook Computer 18 The TouchPad The touchpad is a rectangular electronic panel located just below your keyboard. You can use the static-sensitive panel of the touchpad and slit it to move the cursor. You can use the buttons below the touchpad as left and right mouse buttons. TouchPad Precautions The TouchPad is a pressure sensitive device. Please take note of the following precautions. • Make sure the TouchPad does not come into contact with dirt, liquids or grease. • Do not touch the TouchPad if your fingers are dirty. • Do not rest heavy objects on the TouchPad or the TouchPad buttons. You can use the TouchPad with Microsoft Windows as well as non-Windows applications. How to improve the sensitivity of the touch pad If you want to improve the sensitivity or adjust the speed of your touch pad, please refer to the following sections. Adjusting the mouse pointer speed If you want to adjust the mouse pointer speed, please follow these steps. Chapter 3 Using the Notebook Computer 19 1 Double click the Finger-sensing Pad icon in the task bar. 2 After selecting the Pointer Options tab, set the point speed option in the Motion menu. Then select the Enhance pointer precision option and press the OK button. Chapter 3 Using the Notebook Computer 20 Adjusting the Finger-sensing Pad 1 Double click the Finger-sensing Pad icon in the task bar. 2 Select the Finger-sensing Pad tab, and see if the touch pad program is selected in the Available information and configuration items menu. Then press the OK button. Chapter 3 Using the Notebook Computer 21 Power Saving Modes This section contains information on the Notebook’s power system, including the AC Adapter, the battery system, recharging the battery, and tips for conserving battery power. The power system is comprised of two parts, the AC Adapter and the battery system. The AC Adapter converts AC power from a wall outlet to the DC power required by the computer. The Battery Power System Before using the computer on battery power for the first time, check the battery status icon on the Windows Toolbar to make sure the battery is fully charged. See Battery Status later in this section for a description and explanation of the Windows Battery icon. Charging the battery takes about 4~6 hours to charge when the system is in off state. If possible, always charge the battery completely. Note ✓ If you use typically go through 20 or more charge cycles (full charge to complete discharge), it is highly recommended you perform the Battery Calibration every 3 months to maintain the battery life. ✓ Please refer to the topic on “Battery Calibration” describing how to calibrate your system battery . ✓ If you discover the battery life is getting shorter, please perform the “Battery Calibration” process immediately. Chapter 3 Using the Notebook Computer 22 Removing the Battery Pack To remove the battery pack from its compartment, please refer to Inserting and Removing the Battery Pack. Preparing the Battery Pack for Use (Battery Calibration) Before using the battery pack for the first time, the Smart Battery IC within the battery pack should be calibrated in order to get accurate reporting of remaining battery life status. To calibrate the battery pack follows the instructions below: 1. Insert the battery into the battery compartment and turn on the Notebook. If the battery is completely drained go to the next step. Otherwise, let the battery run down until the low battery warning beeps are heard. The system will automatically enter into Suspend mode. 2. Turn the Notebook off. Connect the AC adapter and let the battery fully recharge. When the battery charge indicator turns off, the battery is fully charged. 3. Turn On the notebook, let the battery run down until the low-battery state is achieved and you hear the warning beeps. The system will automatically enter the Suspend mode. You can now connect the AC adapter. 4. The battery pack is now calibrated properly. In general, using the battery until the low battery-warning indicator appears and then fully recharging the battery each time (full discharge/charge cycle) will ensure accurate reporting of the battery gauge status. Chapter 3 Using the Notebook Computer 23 Automatic Battery Pack Charging Function To charge the battery, while the battery pack is in the notebook, plug the AC adapter into the notebook and an electrical outlet. The charging time is approximately 4-6 hours when the notebook is turned off and approximately 6-10 hours when the notebook is turned on. When the battery is fully charged, the battery charge indicator turns off. Note ✓ Under heavy use or when exposed to high temperatures, the battery may take longer to charge than normal. You need to continue to charge it with the AC adapter plugged in until the charging LED turns off. Battery Status Windows Vista has an applet in the Control Panel that will display an icon in the Windows taskbar indicating when the Notebook is running on battery power or is attached to the AC adapter. This applet also displays a meter that indicates how much charge is remaining in the battery. Chapter 3 Using the Notebook Computer 24 Battery Low Warning When the pack initially reaches the “Battery Low” state approximately 7 ~ 10 minutes of the usable battery life is left. You will hear an audible beep signal every 15 seconds alerting you to the “Battery Low” status. When the battery power reaches the “Battery Low Low” status the beeping sound will accelerate. Your battery now has 1 ~ 2 minutes of battery charge remaining. You must save your data or connect AC power immediately; otherwise, you may lose your data. Sound Meaning Continuous beeping every 5 seconds Battery Low: Indicates that there is 7 to 10 minutes charge remaining. Beeping accelerates Battery Low Low: Indicates that there is 1 to 2 minutes of battery charge remaining. Save your work and turn off the Notebook, or connect the AC adapter. When there is only one minute of battery charge remaining, the Notebook will suspend to the HDD and power off. You should connect AC power and resume to save your work. Small Battery for the Real Time Clock There is a small built-in battery pack that supplies power to the system in order to maintain certain system information while the power is off. If the Notebook is left without a power source for long period of time, this battery will be exhausted and system information will be lost. Chapter 3 Using the Notebook Computer 25 WARNING ✓ Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type recommended by the manufacturer. Dispose of used batteries according to the manufacturer's instructions. Never remove the battery pack while the power is on as this may result in data loss when the system loses power. Adjusting the Brightness To adjust the brightness on the LCD screen, press and hold down the [Fn] key in the lower left hand corner of the keyboard and press the [F8] key to reduce the brightness or [F7] to increase the brightness. Chapter 3 Using the Notebook Computer 26 Using the Windows Help Windows For Windows Vista help, click Start Help and Support icon will open the dialog box. Desktop Desktop may vary differently on the software installed in your notebook with different or additional shortcuts. Recycle Bin Taskbar Start Button Notification Chapter 3 Using the Notebook Computer 27 Recycle Bin Used for storing deleted files in case you want to recover and save it in your system. The files will only be deleted from the Recycle Bin permanently only if you empty it by right clicking your mouse and select the “Empty Recycle Bin”. Start Button Allows easy access to all Windows programs. The Start menu allows you to adapt and show the programs used most frequently. If you wish to keep an item, right click the item and click Pin to Start menu. Log Off will enable the current user to log off and allows a new user to log on. Turn Off Computer allows you to shut down, restart, and Stand by modes for power saving purposes. Chapter 3 Using the Notebook Computer 28 Taskbar When you open a program, its icon is displayed at the taskbar for you to conveniently move between programs by clicking the relevant button. To add or remove toolbars from the taskbar: right click an empty spot on the taskbar, select Toolbars choose the toolbar you want to add. Notification The icons that appear here are for quick access to some programs and computer functions that you frequently used. To prevent Windows Vista from hiding icons: From an empty spot on the Taskbar, right click your mouse and select the Properties, remove the checked mark on the Auto-hide the taskbar. Chapter 3 Using the Notebook Computer 29 Control Panel It is in this area that you can change how Windows looks and works. Click Start There are two interfaces - Classic View. Control Panel dialog box. Chapter 3 Using the Notebook Computer 30 4 Chapter Desktop Operation Chapter 4 Desktop Operation 31 Your notebook is capable of providing you with efficient and productive mobile computing, it also has the speed and capacity to service as a desktop system. This chapter discusses those functions of your notebook that are typical of desktop systems. Audio The Multimedia Sound System The Notebook’s built-in audio capabilities allow you to take advantage of a wide range of education and entertainment multimedia software. The Notebook is equipped with two internal stereo speakers, a microphone, and input audio ports for external audio units. An external microphone can be connected to the microphone jack. External speakers or headphones can be connected to the Notebook’s audio-out jack. External audio devices can be connected to the Line in jack. All audio features are software controlled. The Notebook’s multimedia sound system includes the following features: • Supports Windows Sound System compatibility • Full Duplex operation • Dynamic filtering reduces noise and distortion rate • 16-bit digitized audio playback • Bulit-in stereo speakers • Digitized audio recording through the Notebook’s built-in microphone or any external source Chapter 4 Desktop Operation 32 Audio Volume Control The Notebook is equipped with hot-key volume controls: Pressing the [Fn]+[F11] hot-key combination decreases the audio output volume, press the [Fn]+[F10] hot-key combination increases the audio output volume. Audio Software Your notebook comes equipped with an integrated sound system capable of providing you with quality audio sound through the builtin speakers or through external speakers connected via the system ports. Sound Recording Your system allows you to record sounds and store them as files using the microphone via the microphone jack on the right side of the notebook computer. Check the Windows Help and Support Center in Windows for information on using the various elements in sound recording. Note ✓ For a high-quality sound, click on the "Volume Control" at the lower right end of your screen. From the Volume Control windows, click on the "Advanced" tab, click and select the "Microphone Boost" item. Playing Sound Files Your notebook can play audio files stored in MIDI, WAVE or MP3 file format. Check the Help and Support Center in Windows for information on the functions of the Media Player. External Speakers and Microphone The sound system is capable in providing high-quality sound to external speakers and receiving and processing sounds from an external microphone or external sound source. Connecting Peripheral Devices To expand your computing capabilities, you can add a variety of external devices to your computer. Chapter 4 Desktop Operation 33 Chapter Internet Connection Chapter 5 Internet Connection 34 There are numerous ways to connect to the Internet. This may vary from the user’s working environment as well as system specifications. • Using a wired LAN • Using a wireless LAN Using a Wired LAN for Connection to the Internet For you connect to the Internet, a wired LAN environment normally uses the company’s LAN or a broadband modem. Chapter 5 Internet Connection 35 Using Wireless LAN Network for Connection to the Internet Chapter 5 Internet Connection 36 Chapter Running BIOS Setup Chapter 6 Running BIOS Setup 37 The Setup Utility is a hardware configuration program built into your computer’s BIOS (Basic Input/Output System). It runs and maintains a variety of hardware functions. It is menu-driven software, which allows you to easily configure and change the settings. The BIOS contains manufacture’s default settings for the computer’s standard operations. However, there are occasions when you may be required to modify the default settings in the BIOS. The BIOS allows you to set up passwords to limit access to users. This is an important feature because a great deal of vital information is carried within the computer nowadays. Unauthorized access can be prevented. Later in this chapter, you will learn how to use this security feature. Entering the BIOS Setup Screen First turn on the power. When the BIOS performs the POST (Power-On Self Test), press F2 key quickly to activate the Phoenix BIOS Setup Utility. Note ✓ You may need to press F2 key fairly quickly. Once the system begins to load Windows, you may have to retry by cycle-power on again Leaving the BIOS Setup Screen When you have finished modifying the BIOS settings, exit the BIOS. It takes a few seconds to record changes in the CMOS. Chapter 6 Running BIOS Setup 38 BIOS Action Keys Function Key ESC Enter Command Exit Go to Sub Screen Description Leaves a sub-menu to return to the previous menu OR exits the BIOS setup while saving changes. Shows the Sub Menu F1 General Help Shows the Help Screen F10 Save and Exit Saves changes and reboots the computer.Select a field Selects the next field. Select an item Selects the next upper item. Select an item Selects the next lower item. Lower value Selects the next value within a field. Higher value Selects the next value within a field. Chapter 6 Running BIOS Setup 39 Modifying the BIOS Settings The Phoenix BIOS setup main menu is subdivided into sub-menus. Each menu item is described in this section. Main Under this menu, you may change time/date and view basic processor and system memory information. Advanced Chapter 6 Running BIOS Setup 40 Security Boot Exit Chapter 6 Running BIOS Setup 41 Chapter VGA Utilities Chapter 7 VGA Utilities 42 After you have restarted Windows, click on the Intel® Graphics Media Accelerator Driver for Mobile icon on the lower right corner of the screen. Click on the Graphics Properties to enter the Intel® Graphics Media Accelerator Driver for Mobile display window. You can also click the touchpad or mouse right button and select the Personalize item. Select the Display Settings option to enter its window display. Chapter 7 VGA Utilities 43 Click on the Advanced Settings tab to enter Generic PnP Monitor and Mobile Intel® 4 Series Express Chipset Family window display. Select the Intel ® Graphics Media Accelerator Driver for Mobile and click on the Graphics Properties tab. Chapter 7 VGA Utilities 44 Display Devices This feature allows you to connect external display devices. Display Settings This feature allows you to adjust the color scheme, resolution, refresh rate for your display. Chapter 7 VGA Utilities 45 Color Correction This feature allows you to adjust the color rate of your display. Hot Keys This feature allows you to set the corresponding hot keys in executing the program you frequently use. Chapter 7 VGA Utilities 46 Chapter Troubleshooting Chapter 8 Troubleshooting 47 Your computer has been fully tested and complies with the system specifications before shipping. However, incorrect operations and/or mishandling may cause problems. This chapter provides a reference for identifying and correcting common hardware and software problems that you may encounter. When you encounter a problem, you should first try to go through the recommendations in this chapter. Instead of returning the computer and waiting for repair, you may easily solve the problems by considering the following scenarios and possible solutions. If the error continues, contact your reseller for service information. Before taking further actions, consider the following suggestions: • Check to see if the problem persists when all the external devices are removed. • Check to see that the white light indicator on the AC adapter is it. • Check to see the power cord is properly plugged to the wall outlet and to the computer. • Check to see the power indicator of the computer is on. • Check to see if your keyboard is operational by pressing and holding any key. • Check for any incorrect or loose cable connections. Make sure the latches on the connectors latch securely on to the receptor end. • Be sure you have not performed an incorrect setting on the hardware devices in the BIOS Setup utility. A faulty setting may cause the system to misbehave. If you are not sure of the changes you made, try to restore all the settings to factory defaults. • Be sure all the device drivers are installed properly. For example, without the audio driver properly installed, the speakers and microphone will not work. Chapter 8 Troubleshooting 48 • If external devices such as USB cameras, scanners, printers do not function correctly when connected to the system, it is usually a problem with the device driver or the device itself. Consult the device’s manufacturer first before contacting TriGem USA support center. • Some software programs, which have not gone through rigorous coding and testing, may cause problems during your routine use. Consult the software vendor for problem solving. • Legacy peripheral are not plug-and-play capable. You need to restart the system with these devices powered up and connected first. • Be sure to go to BIOS SETUP and load DEFAULT SETTING after BIOS re-flash. Chapter 8 Troubleshooting 49 Audio Problems No speaker output • Software volume control is turned down in Microsoft Sound System or is muted. Double-click the speaker icon on the lower right corner of the taskbar to see if the speaker has been muted or turned down all the way. • Most audio problems are software-related. If your computer worked before, chances are software may have been set incorrectly. • Go to [Start > Settings > Control Panel] and double-click the Sounds and Audio Devices icon. In the Audio page, make sure that the audio codec mentioned in the spec is the default playback device. Sound cannot be recorded • You will need to plug-in an external microphone to the microphone connector to record sound. • Double-click the speaker icon on the lower right corner of the taskbar to see if the microphone has been muted. - Click Options and select Properties. - Select Recording and click the OK button. - After Click OK button, the recording volume control panel will appear. • Go to [Start > Settings > Control Panel] and double-click the Multimedia icon (or Sounds and Audio Devices icon). In the Volume or Audio page, make sure that the audio codec mentioned in the spec is the default recording device. Chapter 8 Troubleshooting 50 Hard Disk Problems The hard disk drive does not work or is not recognizable • If you had just performed a hard disk upgrade, make sure the hard drive connector is not loose and the hard disk drive is also correctly seated. Remove it and reinsert it firmly, and restart your PC. • The new HDD may need to be partitioned and reformatted. O/S and drivers will need to be re-installed as well. • Check the hard disk indicator LED. When you access a file, the LED lamp should light up momentarily. • The new HDD may be defective or is not compatible. • If your computer has been subjected to static electricity or physical shock, you may have damaged the disk drive. The hard drive is making abnormal whining noises • should back up your files as soon as possible. • Make sure the source of noise is indeed from the hard drive and not the fan or other devices. The hard disk drive has reached its capacity • Run Disk Cleanup utility in Windows. [Start > All Programs > Accessories > System Tools > Disk Cleanup] The system will prompt you for what to do. • Many browsers store files in the hard drive as a cache to speed up the performance. Check the program’s Online Help for instructions on decreasing the cache size or on removing temporary Internet files. • Empty the Recycle Bin to create more disk space. When you delete files, Windows saves them to the Recycle Bin. Chapter 8 Troubleshooting 51 The hard disk takes longer to read a file • If you have been using the drive for a period, the files may be fragmented. Go to [Start > Programs > Accessories > System Tools > Disk Defragmenter] to perform a disk defragmentation. This operation may take a while. • Interrupt requests or problems with other hardware devices may have occupied the CPU and therefore slows down the system performance. The files are corrupted • Run the Error-checking utility in Windows to check the HDD. Double-click My Computer. Right-click C: and select Properties. Click Check Now in Error-checking in Tools. Display Problems The display panel is blank when the system is turned on • Make sure the computer is not in the Standby or Hibernate suspend modes. The display is turned off to conserve energy in these modes. The screen is difficult to read • The display resolution should at least be set to at least 1280x800 for optimal viewing. - Go to [Start > Settings > Control Panel] and double-click the Display icon. - Under the Settings page, set screen resolution to at least 1280x800 and choose at least high(65536) colors. The screen flickers • It is normal if the display flickers a few times during shutting down or powering up. Chapter 8 Troubleshooting 52 Keyboard and Mouse Problems The built-in touch pad performs erratically • Make sure there is no excess perspiration or humidity on your hand when using the touch pad. Keep the surface of the touch pad clean and dry. • Do not rest your palm or wrist on the surface of the touch pad while typing or using the touch pad. The built-in keyboard accepts no input • Please try to make sure the system doesn’t hang up and is still working. The characters on the screen repeat while I type. • You may be holding the keys down too long while you’re typing. • Keep the keyboard clean. Dust and dirt under the keys could cause them to stick. • Configure the keyboard to wait longer before the auto repeat feature starts. To adjust this feature, Go to [Start > Settings > Control Panel], and double-click the Keyboard icon. A dialogue box shows up with the adjustable settings for the keyboard. Chapter 8 Troubleshooting 53 CMOS Battery Problem A message “CMOS Checksum Failure” displays during the booting process or the time (clock) resets when booting • Try to reboot the system. • If the message “CMOS Checksum Failure” appears during the booting procedure even after rebooting, it may indicate failure of the CMOS battery. If so, you need to replace the battery. This battery normally lasts two to five years. The battery is of type CR2032 (3V). Send the battery to the dealer for replacement. Memory Problems The POST does not show an increased memory capacity when you have already installed additional memory • Certain brands of memory module may not be compatible with your system. You should ask your vendor for a list of compatible DIMM. • The memory module may not be installed properly. Go back to Chapter 4 to review the details of this operation. • The memory module may be defective. The O/S issues an insufficient memory error message during operation • This is often a software or Windows-related problem. A program is draining the memory resources. • Close the application programs you’re not using and restart the system. • You need to install additional memory module. For instructions, go to Chapter 4 Upgrading Your Computer. Chapter 8 Troubleshooting 54 PC Card Problems Note ✓ Some system may not have the PC Card Slot option. PC Cards do not function • Make sure you have properly installed the driver for the card. • Consult the card’s manual or contact the vendor for troubleshooting. The PC card cannot be recognized • Make sure the card is fully inserted; the outer end of the card should be even with the edge of the computer. • Remove and insert the PC card again. • Make sure there is no IRQ conflict with the card. See Windows on-line help for solving IRQ conflicts. • Reboot the computer and see if the problem persists. • The card may be defective. Try the card on another system, if possible. Windows crashes or freezes when you remove the PC card • Make sure you have the PC card before removing it. Double-click the Safely Remove Hardware icon at the lower right corner of the task bar and select the card you wish to stop. When you click , in few seconds Windows will prompt you to remove the card. Chapter 8 Troubleshooting 55 Performance Problems The computer becomes hot • In a 60°F environment, the certain areas of the computer’s back case are expected to reach 50 degrees. • Make sure the air vents are not blocked. • If the fan does not seem to be working at high temperature (50 degrees Celsius and up), contact the service center. • Certain programs that are processor-intensive may increase the computer temperature to a degree where the computer automatically slows down its CPU clock to protect itself from thermal damage. The program appears stopped or runs very slowly • Press CTRL+ALT+DEL to see if an application is still responding. • Restart the computer. • This may be normal for Windows when it is processing other CPU-intensive programs in the background or when the system is accessing slow-speed devices such the floppy disk drive. • You may be running too many applications. Try to close some applications or increase system memory for higher performance. • The processor may have been overheated due to the system’s inability to regulate its internal heat. Make sure the computer’s ventilation grills are not blocked. Chapter 8 Troubleshooting 56 USB2.0 Problems The USB device does not work • Check the settings in the Windows Control Panel. • Make sure you have installed the necessary device drivers. • Contact the device vendor for additional support. Chapter 8 Troubleshooting 57 Chapter Specification Chapter 9 Specification 58 CPU • Intel CPU : Core 2 Duo / Paentium Dual core up to 1066Mhz, up to 6M L2 Cache • Package : uFPGA 478 Memory • DDRII 667/800 • DDRII RAM socket * 2 • DDR2 up to 4GB total Core Logic Intel GM45 + ICH9M Support DDRII 667/800 SO-DIMM module per channel Chapter 9 Specification 59 VGA Intel GM45 integrated Graphics(X4500HD) • Supports DX9 & DX10 • Dynamic Video Memory Technology (DVMT) 4.0 support • WMV9(VC-1) and H.264(AVC)support • Spread spectrum clocking (SSC) support. • Analog CRT DAC interface support. Audio Codec Realtek ALC269 • Support 7.1 multi-channels • Azalia standard support • Windows Vista Premium support Card reader (4 in 1) • Support SD/MMC/MS/MS-Pro card • USB I/F Chapter 9 Specification 60 LAN Controller Realtek 8102E • Supports 10 and 100 Mb/sec. Full/Half Duplex operation • RTL8111 Wireless LAN (Optional) Intel Wireless WiFi Link 5100 Series • PCIe Mini card • 2 antenna supported • IEEE 802.11 a/b/g/Draft-N compliant Keyboard • 86 Keys K/B Pointing Device • PS2 Touch Pad with 2 buttons w/o scroll up/down Chapter 9 Specification 61 LCD • LCD is 13.3’’ WXGA, resolution 1280X800 • Glare & non Clare panel/Wide view type HDD • Support SATA II HDD, 1 x 2.5’’( 9.5mm) • 5400rpm support. Battery Pack 2cell pack, 7.3V/5000mAh AC-Adapter • Automatics Voltage adjustment between 100 and 240VAC 50/60Hz • 65 Watts, 3pin Chapter 9 Specification 62 BIOS • Support AMD BIOS Physical Outline • 327(W) x 227.5(D) x 10 - 25(H) mm (w/o rubber foot) • 1.6Kg(+0.5 Kg) w/ 2 cells battery Camera module support (Optional) • 1.3M module • USB interface Fixed LENs. Chapter 9 Specification 63
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.6 Linearized : No Author : momo Create Date : 2009:01:10 10:35:02+08:00 Modify Date : 2009:01:13 11:50:23+08:00 Has XFA : No XMP Toolkit : Adobe XMP Core 4.2.1-c041 52.342996, 2008/05/07-20:48:00 Creator Tool : QuarkXPress3.3K: LaserWriter 8 KH-8.7 Metadata Date : 2009:01:13 11:50:23+08:00 Producer : Acrobat Distiller 9.0.0 (Windows) Format : application/pdf Creator : momo Title : AV N3400 User's Guide_USc00ÎÁõ¿ë Document ID : uuid:50c65f18-0118-4047-a9f4-48968aeb8b82 Instance ID : uuid:2ce5b6a0-21e9-4420-ae20-14ce615a34bb Page Count : 75EXIF Metadata provided by EXIF.tools