Trilliant Networks CONN Wireless Mesh Wide Area Network CPE User Manual Compliances

Trilliant Networks, Inc. Wireless Mesh Wide Area Network CPE Compliances

Manual Appen B

     27 | Appendix B Regulatory Information  Appendix B: Regulatory information  Federal Communications Commission (FCC) compliance notices  This section includes the following FCC statements for the CONN-1000-A, SP-4700-A and related SecureMesh™ and SkyPilot by Trilliant Connectors:  • FCC ID: RV7-CONN (Applies to CONN-1000-A and SP-4700-A) • Class A Interference Statement • RF Radiation Exposure and Hazard Warning • Non-Modification Statement • Deployment Statement  Class A Interference Statement This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a commercial installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:  • Reorient or relocate the receiving antenna. • Increase the separation between the equipment and receiver. • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. • Consult the dealer or an experienced radio/TV technician for help.  FCC Caution: This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:    (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.  RF Radiation Exposure & Hazard Statement To ensure compliance with FCC RF exposure requirements, this device must be installed in a location such that the antenna of the device will be greater than 20 cm (8 in.) away from all persons. Using higher gain antennas and types of antennas not covered under the FCC certification of this product is not allowed. Installers of the radio and end users of the product must adhere to the installation instructions provided in this manual. This transmitter must not be co-located or operated in conjunction with any other antenna or transmitter.  Non-Modification Statement Use only the supplied internal antenna. Unauthorized antennas, modifications, or attachments could damage the CONN-1000-A or SP-4700-A and related SecureMesh™ and SkyPilot by Trilliant Connectors and violate FCC regulations. Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment.  Deployment Statement This product is certified for indoor deployment only in the 5150 – 5250 MHz band. Do not install or use this product outdoors in that frequency band in the United States.  Dynamic Frequency Selection (DFS) in the 5.0 GHz UNII bands The CONN-1000-A has been prohibited from operating in the 5600 to 5650 MHz frequency band for the US and Canada in order to comply with the DFS requirements as outlined in the FCC Part 15, Subpart E rules.
     28 | Appendix B Regulatory Information      Canadian IC Statements  IC: 0628A-CONN (Applies to CONN-1000-A and SP-4700-A).  This device complies with ICES-003 and RSS-210 of Industry Canada. Operation is subject to the following two conditions: 1. This device may not cause interference, and 2. This device must accept any interference, including interference that may cause undesired operation of the device.  Ce dispositif est conforme aux normes NMB003 et CNR-210 d’Industrie Canada. 1. L’utilisation de ce dispositif est autorisée seulement aux conditions suivantes : 2. il ne doit pas produire de brouillage et l’utilisateur du dispositif doit être prêt à accepter tout brouillage radioélectrique reçu, même si ce brouillage est susceptible de compromettre le fonctionnement du dispositif.  RF Radiation Exposure & Hazard Statement To ensure compliance with RSS-102 RF exposure requirements, this device must be installed in a location such that the antenna of the device will be greater than 20 cm (8 in.) away from all persons. Using higher gain antennas and types of antennas not covered under the IC certification of this product is not allowed. Installers of the radio and end users of the product must adhere to the installation instructions provided in this manual. This transmitter must not be co-located or operated in conjunction with any other antenna or transmitter.  Exposition aux radiations RF & Mention de danger Pour assurer la conformité avec les exigences RSS-102 d'exposition aux RF (Radio Fréquences), cet appareil doit être installé dans un endroit ou l'antenne de l'appareil sera située à une distance de plus de 20 cm (8 po) de toutes personnes. L’utilisation d'antennes à gain plus élevé et les types d'antennes qui ne sont pas couverts en vertu de la certification IC de ce produit n'est pas autorisée.  Les installateurs de la radio et les utilisateurs du produit final doivent se conformer aux instructions d'installation fournies dans ce manuel. Cet émetteur ne doit pas être co-implanté ou exploité en conjonction avec toute autre antenne ou transmetteur.  Deployment Statement This product is certified for indoor deployment only in the 5150 – 5250 MHz band. Do not install or use this product outdoors in that frequency band in Canada.  Déclaration de déploiement Ce produit est certifié pour le déploiement à l'intérieur tout en rencontrant les limites de cette bande de fréquences:  5150 - 5250 MHz.  Ne pas installer ou utiliser ce produit à l'extérieur au Canada, si cette bande de fréquences ne peut ne peut être rencontrée.
     29 | Appendix B Regulatory Information   SAFETY INFORMATION   Hazard Warning! High Voltage. This situation or condition can cause injury due to electric shock. Warnung! Lesen und befolgen Sie die Warnhinweise und Anweisungen, die auf dem Produkt angebracht oder in der Dokumentation enthalten sind.    Warning! Read and follow all warning notices and instructions marked on the product or included in the documentation. Warnung! Lesen und befolgen Sie die Warnhinweise und Anweisungen, die auf dem Produkt angebracht oder in der Dokumentation enthalten sind.   Warning! Only use attachments and accessories specified and/or sold by the manufacturer. Warnung! Verwenden Sie nur Zusatzgeräte und Zubehör angegeben und / oder verkauft wurde durch den Hersteller.   Warning! Refer all servicing to qualified service personnel. Servicing is required when the device has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the device, the device has been exposed to rain or moisture, does not operate normally, or has been dropped. Warnung! Das Gerät sollte nur von qualifizierten Fachkräften gewartet werden. Eine Wartung ist fällig, wenn das Gerät in irgendeiner Weise beschädigt wurde, wie bei beschädigtem Netzkabel oder Netzstecker, falls Flüssigkeiten oder Objekte in das Gerät gelangen, das Gerät Regen oder Feuchtigkeit ausgesetzt wurde, nicht ordnungsgemäß funktioniert oder fallen gelassen wurde.   Warning! Do not open the chassis. There are no user-serviceable parts inside. Opening the chassis will void the warranty unless performed by an Trilliant service center or licensed facility. Warnung! Öffnen Sie das Gehäuse nicht. Keine der Geräteteile können vom Benutzer gewartet werden. Durch das Öffnen des Gehäuses wird die Garantie hinfällig, es sei denn, solche Wartungsarbeiten werden in einem Trilliant-Service-Center oder einem lizenzierten Betrieb vorgenommen.

Navigation menu