Trilliant Networks G30FOCUS Wireless Electric Meter User Manual Manual

Download:
Mirror Download [FCC.gov]
Document ID	1405106
Application ID	stxNnrEMqYQ1M1HF2q5U1g==
Document Description	Manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	27.86kB (348197 bits)
Date Submitted	2011-01-14 00:00:00
Date Available	2011-01-14 00:00:00
Creation Date	2010-06-22 13:49:00
Producing Software	Acrobat Distiller 8.1.0 (Windows)
Document Lastmod	2010-06-22 13:49:00
Document Title	Microsoft Word - pa-0129a1.0-RES-3000-Focus with FCC Statements.doc
Document Creator	PScript5.dll Version 5.2.2
Document Author:	nwhitehead

RES-3000-Focus
RES-3000-FocusAX
SecureMesh retrofit for Focus/FocusAX meter
Introduction
This document will help the SecureMesh user to retrofit the product model RES-3000Focus/FocusAX in a Landis &Gyr Focus® meter as intended.
Safety and Assembly Cautions
- Warning: The meter carries lethal voltages. The meter must be completely
disconnected from any external circuits. Failure to observe this practice can result in
serious injury or death.
- Caution: These devices are electrostatic sensitive. It is best to use a grounded
electrostatic mat and wrist strap to prevent electrostatic discharge.
- Important: It is not necessary to completely separate the top of the meter from the base
of the meter for this retrofit procedure. However, if the two parts are completely
disconnected and separated, it is extremely important to keep each meter component
together for re-assembly. This is due to the top section of the meter containing
calibration “characterization” programming for the CTs in the meter base. If these
components get mixed up with other meter components, current measurement errors will
occur.
Material
• Focus meter (must be AMR configured)
• Trilliant SecureMesh RES-3000Focus/FocusAX .
• Mounting Screws - QTY=3 (provided by
L&G, ref.Trilliant # HS-0029B & HS-0029C)
• Self-Retaining Spacers-QTY=3
(provided by L&G, ref. Trilliant # HE0033C & HE-0033D)
• Serial # & FCC/IC label (provided by
L&G, ref Trilliant #.: HI-0307A)
PA-0129A Rev. 1.0
June 18, 2010
Page 1 of 4
RES-3000-Focus
RES-3000-FocusAX
Procedure
1. If it is not already done, dis-assemble
the Focus meter clear cover and
unsnap the base from the top portion
of the case to access the 3 post
receptacle holes in the Top Portion
and the Focus/FocusAX board
connector as shown.
Male Interface
connector
Meter TOP
portion
Post
receptacles
HE-0033C
Short Spacer
2. Snap the 3 plastic spacers into the
Trilliant SecureMesh RES-3000Focus/FocusAX PCB as showm.
Plastic
spacers
HE-0033D
HE-0033D
Be careful to not damage
components and or PCB
traces when inserting spacers.
Do not apply excessive stress
on the PC board. Bending the
board too much would damage
components.
Female
connector
3. Install the SecureMesh board by first
inserting the female connector in the
Focus/FocusAX male connector as
shown. The 3 spacers will be aligned with
the 3 holes in Focus/FocusAX meter Top
Portion.
Male-Female
connector mating
PA-0129A Rev. 1.0
June 18, 2010
Page 2 of 4
RES-3000-Focus
RES-3000-FocusAX
4. Attach the three (3) mounting screws
through the SecureMesh PCB into
the 3 plastic spacers so that the
SecureMesh board is held securely
in place.
Screw
Ref: HS-0029B
Screw
Ref: HS-0029B
Screw
Ref: HS-0029C
5. Affix any missing label (Ref.: HI-0307A) on
the meter Top Portion,
finalize inspection & test as required
6. Reassemble the Focus Top portion by
snapping it into the bottom portion and affix
the clear cover on its base.
7. Perform functional test.
PA-0129A Rev. 1.0
June 18, 2010
Page 3 of 4
RES-3000-Focus
RES-3000-FocusAX
SecureMesh Radio Specifications:
•
•
•
•
•
•
•
•
•
IEEE Standard :
Power Output :
Radio Sensitivity :
RF Data rate :
Operating Frequency :
Network Topology :
Modulation :
Physical Dimensions :
Antenna :
IEEE 802.15.4
+30 dBm
-99 dBm
250 kbps
2.400-2.483 GHz
Mesh
O-QPSK
2.33” x 4.70”
Dipole, 3.5 dBi
Industry Canada and Federal Communication Commission Compliance Statement
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
1. This device may not cause harmful interference, and
2. This device must accept any interference received, including interference that may cause
undesired operation.
FCC Warning
Changes or modifications not expressly approved by the party responsible for compliance could void the
user’s authority to operate the equipment.
FCC Interference Statement
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant
to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates uses and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may cause harmful interference
to radio communications. However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try to correct the interference by
one of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
• Consult the dealer or an experienced radio/TV technician for help.
To comply with FCC and Industry Canada RF exposure limits for general population / uncontrolled
exposure, the antenna(s) used for this transmitter must be installed to provide a separation
distance of at least 20 cm from all persons and must not be co-located or operating in conjunction
with any other antenna or transmitter.
PA-0129A Rev. 1.0
June 18, 2010
Page 4 of 4

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.4
Linearized                      : Yes
XMP Toolkit                     : Adobe XMP Core 4.0-c316 44.253921, Sun Oct 01 2006 17:14:39
Producer                        : Acrobat Distiller 8.1.0 (Windows)
Creator Tool                    : PScript5.dll Version 5.2.2
Modify Date                     : 2010:06:22 13:49-04:00
Create Date                     : 2010:06:22 13:49-04:00
Format                          : application/pdf
Title                           : Microsoft Word - pa-0129a1.0-RES-3000-Focus with FCC Statements.doc
Creator                         : nwhitehead
Document ID                     : uuid:19334ba3-cb1a-4ed4-999f-318d134d149c
Instance ID                     : uuid:e721c4e3-bc14-4771-ab12-2818d6eda994
Page Count                      : 4
Author                          : nwhitehead

EXIF Metadata provided by EXIF.tools