Trimble RC60X Remote Control Transmitter User Manual manual

Trimble Inc. Remote Control Transmitter manual

manual

1TABLE OF CONTENTSIntroduction 2FOR YOUR SAFETY 2COMPONENTS 2How to use the Laser System 3 Powering the Laser 3 RC603 Radio/IR Remote Control 3 Turning On/Off the RC603 3LASER SETUP 4 Turning On/Off the Laser 4 Features and functions 4 Standard Features 5 X-Y-Z-grade entering mode 5 Using the Rotation mode 6 Using the Scan mode 6 Manual mode 6 Special MENU Features 7 Menu Functions (Radio controlled) 7 Menu Functions (IR controlled) 7 Automatic PlaneLok mode 8 Automatic Grade Match 8 Manual Grade Match 9 Automatic Axis Alignment 9 Manual Spot Search mode 10 Activating/Deactivating Standby mode 10 Start Reference Check 11 Centering the Rotor 11 Setting Menu 11 Info 11 Service menu 11Special Features - Vertical Setup 12 Z-Axis Automatic Spot Align 12 Z-axis Automatic Spot Lok 13 Z-axis Automatic Spot Match 13 Line Scan 14 Beam Plunge 14 Setting menu details 14 Pairing 14 Pairing the transmitter with remote control 15 Pairing the transmitter with receiver 15 Mask mode 15 Grade Entry 16 Grade Display 16 Sensitivity 16 HI-alert selection 16 User Name 17 Set Password 17 Password On/Off 17 Radio RF-Channel) 17CALIBRATION 18 Checking Calibration of the Y- and X-Axes 18 Checking Calibration of the Z-(vertical) Axis 18Troubleshooting 19SF601 Spot Finder User Guide 20 PROTECTING THE UNIT 23CLEANING AND MAINTENANCE 23PROTECTING THE ENVIRONMENT 23WARRANTY 23TECHNICAL DATA 24GB120432trimble_UL633_01_GB.indd 1 14.04.12 11:40
2IntroductionThank you for choosing one of the Spectra Precision Lasers from the Trimble family of precision lasers.The universal laser is an easy-to-use tool that offers accurate horizontal, vertical and sloped laser reference up to 1300 ft (400 m) away using a receiver. The plumb beam can be detected automatically and manually using the additional SpotFinder For Your Safety For hazardless and safe operation, read all the user guide instructions.LASER RADIATIONAVOID DIRECT EYE EXPOSURE CLASS 3A/3R LASER PODUCT• Useofthisproductbypeopleotherthanthosetrainedonthisproductmayresultinexposuretohazardouslaser light.• Donotremovewarninglabelsfromtheunit.• TheUL633isClass3A/3R(<5mW,600...680nm).• Neverlookintothelaserbeamordirectittotheeyesofotherpeople.• Alwaysoperatetheunitinawaythatpreventsthebeamfromgettingintopeople‘seyes.• Ifinitialserviceisrequired,whichresultsintheremovaloftheouterprotectivecover,removalmustonlybeperformed by factory-trained personnel.Caution:Useofotherthanthedescribeduserandcalibrationtoolsorotherproceduresmayresultinexposuretohazardouslaserlight.Caution:UsingdifferentthandescribedattheUL633userguide,mayresultinunsafeoperation.COMPONENTS a Keypad/LCD-Display b Handle c Rotor with fan beam lens d Sunshade e Axes-Alignment-Marks f Sighting Guides/Scope Mounts g Battery door h Rubber Cover/Recharge Jack i 5/8” x 11 Tripod Mounts j Rubber Feet k Turnable Legs l Plus and Minus Battery Diagrams120432trimble_UL633_01_GB.indd 2 14.04.12 11:40
3HOW TO USE THE LASER SYSTEMPOWERING THE LASERBatteriesWARNING Ni-MHbatteriesmaycontainsmallamountsofharmfulsubstances.Besuretochargethebatterybeforeusingitforthersttime,andafternotusingitforanextendedlengthoftime.Chargeonlywithspeciedchargersaccordingtodevicemanufacturer‘sinstructions.Donotopenthebattery,disposeofinreorshortcircuit;itmayignite,explode,leakorgethotcausingpersonalinjury.Disposeinaccordance with all applicable federal, state, and local regulations. Keep the battery away from children.Ifswallowed,donotinducevomiting.SeekmedicalattentionimmediatelyRecharging the BatteriesThelaserisshippedwitharechargeableNi-MHbatterypack.Note: TheapproximatechargeofthebatteriesisshownatthelefttopsideoftheLCD.Thechargerrequiresapprox.10hourstochargeemptyrechargeablebatteries.Forcharging,connecttheplugofthechargertotherechargejackofthebatterypack.Neworlong-timeout-of-userechargeablebatteriesreachtheirbestperformanceafterbeingchargedandrechargedvetimes.ForIndoorapplicationsthechargercanbeusedasapowersupplyfortheUL.Alkalinebatteriescanbeusedasabackup.Insert4D-cellbatteriesnotingtheplus(+) and minus (-) diagrams inside the battery housing.The batteries should only be charged when the laser is between 50° F and 104° F (10°C to 40°C). Charging at a higher temperature may damage the batteries. Charging at a lower temperature may increase the charge time and decrease the charge capacity, resulting in loss of performance and shortened life expectancy. RC603 Radio/IR Remote ControlPowering the RC6031. Open the battery door using a coin or similar pry device to release the batterydoortabontheRC603.RC603willbeshippedwithalkalinebatteriesRechargeablebatteriescanbeusedoptionalbutneedtobechargedexternally2.InserttwoAAbatteriesnotingtheplus(+)andminus(-)diagramsinside the battery housing.3.Close the battery door. Push down until it “clicks” into the lockedposition.Turning On/Off the Radio/IR Remote ControlTheradio/IRremotecontrolisahand-helddevicethatallowsyoutosendoperationalcommandstothelaserfrom a remote location.Pressthepowerbuttontoturnontheradio/IRremotecontrol.A“ ”andadditionalverticalbarsappearinthe right corner of the remote’s top display line indicating the radio connection status between the laser and theremotecontrol.IftheRC603isoutsidetheradiooperatingrangetheremoteswitchesautomaticallyintotheIRconnectioncapability.Note:Whentheremotecontrolisinitiallyturnedon,thestandarddisplay(modelnumberandsoftwareversion)appearfortherst3seconds,thentheaxessymbolsandlast-enteredgradeforeachaxisbrieyappearintheLCD.Witheverybuttonpress,theLCDbacklightisactivatedandturnsoffautomaticallyifnobuttonispressedfor8seconds.To turn off the radio remote control, press and release the power button.Note:5minutesafterthelastbuttonpress,theremotecontrolturnsoffautomatically.120432trimble_UL633_01_GB.indd 3 14.04.12 11:40
4LASER SETUPPosition the laser horizontally (tripod mount and rubber feet downward!) on a stable platform, wall mount or tripod at the desired elevation.The laser recognizes automatically whether it is used horizontally or vertically when switched on. Turning On/Off the laserPressthepowerbuttontoturnOn/Offthelaser.Note:Dependingonthesetup(horizontalorvertical)andifagradevaluehasbeendialedin,theunitstartsthetemperature/referencecheckwhilethethermometersymbolisashing.Whenthetemperature/referencecheckhasbeennished,thestandarddisplayappearsandthebubblesymbolsashuntilself-levelinghasbeencompleted.Iftheself-levelingcan’tbenishedbasedontheselectedsensitivity,anerrormessageappears.AbubblesymbolhelpstoadjusttheunitatthecrossaxiswhensetupverticalforautomaticSpotAlignorinvertical manual mode.Features and Functions Standard DisplayTheremotecontrolmirrorsthefunctionalityoftheULkeypadButton 1: Quickly press and release starts the MENU entry.Button 2: Quickly press and release starts the grade entering mode.Button 3: Quicklypressandreleaseactivates/deactivates the manual mode. Button 4: Quickly press and release to toggle through the pre-selected rotation speeds. Press and hold for three seconds changes the unit into scan mode.Wheninscanmode,quicklypress and release button 4 toggles through the pre-selected scan sizes.Button 5, 8:up/downarrowbuttons.Button 6, 7:left/rightarrowbuttons.Button 9: ON/OFFbutton-pressfor1secondtoturnontheunit;pressandholdfor2seconds to turn off the unit.Leveling/Standby – LED (green/red)Batterystatuslaser HIalertfunctionisactivatedMaskselection BatteryStatusRemoteControlStatusRadioConnectivityRotationspeed/ScanangleFanBeamisactivated120432trimble_UL633_01_GB.indd 4 14.04.12 11:40
5Standard FeaturesX-Y-Z-grade entering – Step and Go mode Quickly press and release button 2startsthegradeenteringmode.Bothgradevalueswillbeshown.Press/releasebutton1 a grade reverse YPress/releasebutton2 a grade reverse XPress/releasebutton3 a return to the standard displayQuickly press and release button 4toconrmtheselectedgradevalueandreturn to the standard displayPress and hold button 6 or 7(left/right)tochangeX-axisgradevalueafterthecomma;pressandholdbuttons6 + 7simultaneouslystartsX-axisquickchangemodewherethegradevalueinfrontofthecommawillbesetto 0% and then starts changing in 1% increments.Press and hold button 5 or 8(up/down)forchangingY/Z-axisgradevalue;pressandholdbuttons 5 + 8 simultaneouslystartsY/Z-axisquickchangemodewherethegradevalueinfrontofthecommawillbesetto 0% and then starts changing in 1% increments.Note: The speed of the grade value change increases with the amount of time the button is held down.Note: Thegradevalueforbothaxesincreasesin1.00%increments.Whenthegradevalueforeitheraxisreachesitshighestamount,thegradevalueswitchestothelowestvalueforthataxis.Forexample,thevalueswitchesfrom+25%to-25%.Thelaserwillself-leveltotherequiredgradepositionafterconrmingthegradechangewithbutton4.Note:Thebubblesymbolsatthelaser’sLCDwillashuntilthelaserhasbeenself-leveledtotherequestedgrade position.X-Y-Z-grade entering – Digit Select mode (Default) Quickly press and release button 2 starts the grade entering mode. .Bothgradevalueswillbeshown.Press/releasebutton1 aquicksetto0%Press/releasebutton2 a change the sign in front of the grade valuePress/releasebutton3 a return to the standard display.Quickly press and release button 4toconrmtheselectedgradevalueandreturntothestandarddisplay.Press and release button 5 or 8(downorup)tomovethecursortotheX-orY-axis(notusedinZ-mode)Pressing and releasing button 6 or 7(rightorleft)movesthecursortotheright/left.120432trimble_UL633_01_GB.indd 5 14.04.12 11:40
6Usebutton 1 or 2(PlusorMinus)tosetthedesireddigit.Thelaserwillself-leveltotherequiredgradepositionafterconrmingthegradechangewithbutton4.Note: Thebubblesymbolsatthelaser’sLCDwillashuntilthelaserhasbeenself-leveledtotherequestedgrade position.Using the Rotation modeRepeatedlypressingthebutton4togglesthrough0,80,200,600,900rpmregardlessiftheunitis in automatic or manual mode.At0rpm,thebeamstopsautomaticallyclosetothe+Y-axiscenterposition(pipelayingoverthe top).Whensetup inautomaticorgrademode,usingbuttons5/8increases/decreasesrotorspeedfrom0to80andthenupto900rpmcontinuouslyin10rpmincrements.Pointing modeAt0rpm,buttons6/7movethebeamtotheleft/rightside.Whensetupverticallyat0rpm,button5/8 move thebeamclockwise/counterclockwise.Note: Press and hold button 4 for three seconds to change the unit from rotation mode (default) into scan mode.Using the Scan modePress and hold button 4attheStandardDisplayforthreesecondstochangetheunitintoscanmode.Quickly press and release button 4totogglebetweenthepre-selectedscansizes5,15,45,90,180degreesand0;regardlessiftheunitisinautomaticormanualmode.Whenworkinginhorizontalautomaticmode,pressandholdbutton5/8toincrease/decreasethelinesizein5degreesincrements.Pressandholdbutton 6/7movesthescanlinetotheright/leftdirection.Whenusedinautomaticverticalmode,pressingandholdingbutton5/8movesthescanlinecounterclockwise/clockwise.Whensetupvertical,pressingandholdingbutton6/7movesthescanlineintotheright/leftdirectionregardless if in automatic or manual mode.Note: Press and hold button 4 for three seconds to change the unit back to rotation mode (default) mode. Manual modePressing and releasing button 3attheStandardDisplayactivates/deactivatesthe manual mode regardless if set up horizontal or vertical.Manual mode is indicated by horizontal lines next to the axes symbols.Anadditionalbubblehelpstoadjustthelaseronthecrossaxiswhensetupvertical.InManualmode(horizontal),theY-axiscanbeslopedbypressingtheUp-(5)andDown-Arrow-(8) buttons on thelaser‘skeypadortheremotecontrol.Additionally,theX-axiscanbeslopedbypressingtheLeft-(6) and Right-(7)Arrow-buttonsonthelaserorremotecontrol.Inverticalmode,theupanddownarrowbuttonsadjusttheZ-axisslope,andtheleftandrightarrowbuttonsalignthelaserbeamtotheright/leftside.To resume automatic self-leveling mode, press the manual button again.120432trimble_UL633_01_GB.indd 6 14.04.12 11:40
7Special MENU FeaturesMenu Functions (Radio controlled)Press and release button 1attheStandardDisplaytoentertheMENU.The menu offers always only the features which can be selected depending on the setup (horizontal or vertical).The icon of the selected function will be highlighted.A down arrow at the the right site indicates that the user can scroll  down through the menu using the button 8 (down arrow).Aftergoingtothenextmenurow,anup/downarrowatthetherightsiteindicatesthattheusercanscrollup/down through the menu (4 different screens) using the buttons 5/8(up/downarrows).Pressing and releasing button 3 changes the unit always back to the standard or previous display.Press and release the buttons 6/7 until the desired icon at the selected menu row is highlighted.Press and release button 4toopenthesubmenuORstarttheselectedfunction.Menu functions when set up horizontalMenu functions when set up verticalMenu Functions (IR controlled)IftheRC603ispairedwithatransmitterandtheradioconnectiondoesn’twork,e.g.,throughapipe,theIRconnection offers the following functions.PressandreleasetheMENUbuttonattheStandardDisplay.Pressing and releasing button 3 changes the unit always back to the standard or previous display.Press and release the buttons 5 to 8 until the desired icon is highlighted.Press and release button 4toopenthesubmenuORstarttheselectedfunction.Note: Pairing function is needed to pair an already paired remote with a new transmitter.The new transmitter has to be set to the pairing dialog for this operation. Otherwise the pairing can not be successful processed. The pairing information of the previous pairing is still stored in the previous paired transmitter and should be deleted in the pairing dialog of this transmitterNote:IfaremoteispairedwithatransmittertheIRsignalsoftheremote(incaseofaninterruptedradioconnection) will transmitted in a private mode so that only the paired transmitter can received these IRcommands.120432trimble_UL633_01_GB.indd 7 14.04.12 11:40
8Automatic PlaneLok modeThe PlaneLok mode can be activated in horizontal and vertical automatic and manual mode. InPlaneLokmodewhensetuphorizontal,thebeamwillbelockedtoaxedelevationpoint(upto80m(260ft)locatedononeorbothaxesateachsideofthelaser.Forkeepingverticalalignmentsxedtoadirectionpoint,PlaneLokcanbeusedinbothdirectionsontheX-axis.1. Set up the laser over the reference point.2.AttachtheHL750receivertoagraderod.PlacethereceiveratthesecondpointandadjustittotheOn-gradeposition.Thereceivershouldbepermanentlymountedatthis location and at the desired elevation.3.Usethesightingguidesonthetopofthelasertoalignthelasertothereceiver.Turnthelaseronthetripoduntilitisroughlyalignedtothereceiver’sposition(thealignmentrangeforbothaxesis+/-40°).4.PressandreleasetheMENUbuttonattheStandardDisplayandselectPlaneLok.Inverticalmode,PlaneLokcanbestartedimmediatelybypressingbutton4. Horizontalsetup Vertical setup5.Whensetuphorizontally,pressandreleasebutton4toopenthePlaneLoksubmenu;selectthedesiredPlaneLokaxisthenpressbutton4 to start PlaneLok.Note:Thelaserstartstosearchforthereceiver.AashingReceiverandLocksymbolappearsattheselectedaxisandbecomessolidwhenPlaneLokhasbeencompleted.Note:Whenusedinverticalmode,thereceiverhastobeplacedwith the photocell on the bottom side.The HL750 display shows a ashing –PL– during the time thelaserissearchingandadjustingthebeamtotheon-gradeposition.When PlaneLok is complete, –PL– stops ashing at the HL750display. Note: The laser continues to servo to the receiver’s signals. 6.ExitingofPlaneLokcanbedonebypressingbutton3(ESC).Automatic Grade MatchTheGradeMatchmodecanbeactivatedinhorizontalautomaticandmanual mode.InGradeMatchmode,thelasercanbeusedtomeasuretheexistinggradevaluebetweentwoknownelevationpoints(upto80m(260ft)locatedononeorbothaxesateachsideofthelaser1. Set up the laser over the reference point.mm120432trimble_UL633_01_GB.indd 8 14.04.12 11:40
92.AttachtheHL750receivertoagraderod.Checkthelaser’selevationnexttothelaserthenpositionthereceiveratthesecondpointWITHOUTchangingthereceiver’selevationontherod.3.Usethesightingguidesonthetopofthelasertoalignthelasertothereceiver.Turnthelaseronthetripoduntilitisroughlyalignedtothereceiver’sposition(thealignmentrangeforbothaxesis+/-40°).4.PressandreleasetheMENUbuttonattheStandardDisplayandselectGradeMatch. 5.SelectthedesiredGradeMatchaxisthenpressbutton 4tostartGradeMatch.Note:Thelaserstartstosearchforthereceiver.AashingReceiverandanglesymbolappears at theselected axis anddisappears when GradeMatch hasbeen completed.Whilethelaserissearchingandadjustingthebeamtotheon-gradeposition,theHL750displayshowsaashing–GM–.WhenGradeMatchhasbeencompleted,theHL750goesbacktothestandardelevationdisplay.Theremotecontrolaswellasthelaserwilldisplaythenalmeasured grade value.Note:IfGradematchcan’tbecompletedbycheckingthelimits,thelasercomeswithanErrormessage(GradeMatchhasFailed)whichcanbedeletedwithbutton4(OK).TheHL750goesback to standard elevation indication.Manual Grade MatchInManualGradeMatch,thebeamonbothaxescanbeadjustedtothereceiver‘son-gradeposition,e.g,whenotherreceiversastheHL750areused.ThegradefortheY-axiscanbeadjustedwithbutton5/8 while button 6/7 adjusttheX-axis.DuringManualGradeMatchacrossedvialandanglesymbolappearnexttothecontinuouslychangingY-andX-axisgradevalue.Afteradjustingtothereceiver’son-gradeposition,pressbutton2 (OK) to gobacktoautomaticmodewherethenalgradevaluewillbeshownforbothaxes.Note: Pressing button 3(ESC)exitsManualGradeMatchandchangestheunittomanualmode.Automatic Axis AlignmentAutomaticAxisAlignment mode adjusts automatically the directionthegradeaxisispointingtothereceiver’slocationbyanelectronicallysimulationofrotatingtheunitonitsbasetomatchthehub.UsingAxisAlignment,thelaseraxescanbealignedtooneortwodirectionhubs(upto80m(260ft)locatedononeorbothaxesateachsideofthelaser.1. Set up the laser over the reference point.2.Place the grade rod with the attached HL750 receiver at thedesired direction hub. 3.Usethesightingguidesonthetopofthelasertoalignthelasertothe receiver. Turn the laser on the tripod until it is roughly aligned tothereceiver’sposition(thealignmentrangeforbothaxesis+/-40°).mm120432trimble_UL633_01_GB.indd 9 14.04.12 11:40
104.PressandreleasetheMENUbuttonattheStandardDisplayandselectAxisAlign.5.Selectthedesiredaxisthenpressbutton4tostartAxisAlign.Note:Adjusting thereceiver into the beam beforestarting the automaticAxisAlignmentreduces the timeneededfornishingthealignment.Selecting the menu icon „View Axis Angle“showsthealignmentangle after an axisalignmenthas beencompleted. This function can be used to measure an angle difference between two direction hubs in a range uptomax.80°byperformingtwoaxisalignmentsinsequence.The menu icon „Axis Angle Input“selectionallowstodialinanaxisanglewheretheaxisdirectionwillbealignedtooafterarstaxisalignmenthasbeendone.Tworowsareavailablefortypinginaxisanglevalues.Button5 and 8canbeusedtotogglebetweenbothrows.Changingthesignandnumberscanbedoneusingthe buttons 1 and 2. Press and release button 4toconrmtheselectedaxisangles.TheaxeswillbeadjustedwhilethedisplayfallsbacktothemainMenu.Press and release button 3(ESC)toexittheAnglefunctions.Manual Spot Search mode The Spot Search mode is used for detecting the plumb beam manually using the Spot Finder SF601andcanbeactivatedinhorizontalandverticalautomaticandmanualmode.PressandreleasetheMENUbuttonattheStandardDisplayandselectSpotSearch.Pressing button 4activatesthefanbeamwhiletherotationspeedchangesto900rpmandtheunit goes back to the standard display.The4redLEDsaroundthecenterholeguidetheusertotheplumbbeam‘scenterposition-all4LEDson=>conrmationtheSF601hasbeensettothecorrectcenterposition.Note:ManualSpotSearchcanalsobeactivatedanytimebyturningontheSpotFinderSF601.TurningOfftheSF601deactivatestheSpotSearchmodeimmediatelybydeactivatingthefanbeam.Activating/Deactivating Standby modePressandreleasetheMENUbuttonattheStandardDisplayandselectStandby.Pressing and releasing button 4 activates the Standby mode. Theself-levelingwillbestoppedandthebeamwillbeturnedoffwhiletheHIalertisstillactive.ThedisplayshowsthestandbysymbolandtheLevel/StandbyLEDashesredevery5seconds.To deactivate Standby mode and restore full operation of the laser, press and release button 4.120432trimble_UL633_01_GB.indd 10 14.04.12 11:40
11Start Reference Check Before starting some grade work which is very sensitive an additional Reference Check canbestartedmanually. Press and release the MENUbuttonattheStandardDisplayandselectReferenceCheck.Pressing and releasing button 4startstheReferenceCheckconsideringthecurrenttemperatureinsidethehousing.Whiletherotorchecksthecorrectpositiontherotationwillbestopped.Centering the Rotor PressandreleasetheMENUbuttonattheStandardDisplayandselectCenteringwheretherotorwillbecentered90°perpendiculartothebottomhousing.Pressing and releasing button 4 starts the rotor centering function while the rotor checks the limitsofbothaxesthenitstopsatthecenterpositionandchangestheunitintomanualmode.Setting MenuPressandreleasetheMENUbuttonattheStandardDisplayandselectSettings.Press and release button 4toopentheSettingMenu;selectthedesiredfunctionthenpressbutton4toopentheselectedsubmenufunctionORstarttheselectedfunction.PleaseseetheSettingMenudetailsattheendoftheuserguide.InfoPressandreleasetheMENUbuttonattheStandardDisplayandselectInfo.Buttons6/7canbeusedtotogglebetweenUL,RCandRuntime.Press and release button 4toconrmtheselection.TheUL/RCinformation(softwareversion,ID,etc.)ortheruntimeoftheULwillbedisplayed. ServicePressandreleasetheMENUbuttonattheStandardDisplayandselectService.Buttons6/7 can be used to toggle between Calibration Y and Calibration XOR Calibration Z when set up vertically.Press and release button 4 to conrm the selection.The calibration at the selected axis starts the eldcalibration procedure.120432trimble_UL633_01_GB.indd 11 14.04.12 11:40
12The RC603 Service menu offers additional features:RF IR optionsPress and release button 4toconrmtheselectionandselectoneofthefollowingoptions:RFOn;IRauto=>Radioonalltimes;IRwillbeactivatedautomaticallyafterradioconnectionhas been lost.RFOff;IROn=>RadioturnedOff;IRalwaysactivatedRFOn;IROff=>RadioturnedOn;IRalwaysOffRF ConnectivityPress and release button 4togetastatusofthecurrentRadioconnectivity.Special Features - Vertical SetupZ-Axis Automatic Spot Align TheSpotFinderSF601guidestheplumbbeamtothetargetpointinthehorizontalaxis,whiletheZ-axisgradevalue will be maintained. Used for rst and secondday alignment (pipe laying applications). Using SpotAlignment,theplumbbeamcanbealignedautomaticallytoonedirectionhub(upto80m(260ft)locatedinfrontof the plumb beam.1.Setupthelaseroverthestartpoint,e.g.,attherstmanhole ring.2.Adjustthedisplaybubbletothecenteredposition.3.TurnonandattachtheSF601SpotFinderatthedesireddirectionhub.4.PressandreleasetheMENUbuttonattheStandardDisplay;selectSpotAlignandstartthefunction using button 4 (fan beam will be activated).Note:SpotAligncanalsobestartedthroughthepipeusingtheRC603viainfrared.Note:ThedisplayfallsbacktothestandarddisplaywhileaSpotFindersymbolisashing.TheplumbbeamwillbeautomaticallyalignedtothecenteroftheSF601.5.Afteralingmentiscomplete(all4redLEDsattheSF601areon),theplumbbeamwillmoveverticallytothepreviousdialedinZ-axisgradevalue.Note:AutomaticSpotAligncanbeexitedanytimebypressingandreleasingbutton3(ESC).120432trimble_UL633_01_GB.indd 12 14.04.12 11:40
13Z-axis Automatic Spot LokAutomatic SpotLok (likePlaneLok)canbeusedtoalignandholdtheplumbbeamautomaticallytotheSF601’scenterpointandcontinuouslyadjustingtheZ-andX-axisuntilexitingthismode.TheULlooksalwaystothecenterpositionoftheSF601andre-adjuststhebeamimmediatelytothecentertoavoidanysetup/alignmentdriftcausedbyvibrationsortemperatureinuences(e.g.whenworkingonconcretepads,facadeapplications).UsingSpotLok,theplumbbeamcanbealignedautomaticallytoonedirectionhub(upto80m(260ft)locatedin front of the plumb beam.1. Set up the laser over the start point. 2.PlacetheSF601SpotFinderatthesecondreferencepoint.3.Press and release the MENU button at the StandardDisplay,selectSpotLokandstartthefunctionusingbutton4 (fan beam will be activated).Note: Spot Lok can also be started via infrared using the RC603.Note:ThedisplayfallsbacktothestandarddisplaywhileaSpotFinderandlockiconisashing.TheplumbbeamwillbeautomaticallyalignedtothecenteroftheSF601.4.AfterSpotLokiscompleteall4redLEDsattheSF601areonandtheiconsstopashing.Thetransmitter‘splumbbeamisalwayscheckingforperfectalignmenttothecenteroftheSF601.All4LEDsashevery5secondstoconrmthecorrectalignment.Note:AutomaticSpotLokcanbeexitedanytimebypressingandreleasingbutton3(ESC).Z-axis Automatic Spot MatchAutomatic-Spot-Match canbeusedformeasuringanunknowngradevaluebetweentwoexistingelevationse.g.,inanexistingpipewhichneedstobereplacedoranopentrenchwithanunknowngradevalue.TheplumbbeamwillbeautomaticallyalignedtotheSF601centerpoint(Z-andX-axis)andswitchesbacktoautomaticZ-axisgrademodewhiledisplayingthemeasuredZ-gradevalue.UsingSpotMatch,theplumbbeamcanbealignedautomaticallytoonedirectionhub(upto80m(260ft)located in front of the plumb beam..1.Setupthelaseroverthestartpoint,e.g.,attherstpipeor trench start point.2.PlacetheSF601SpotFinderatthelastpipeorendofthe trench.3.Press and release the MENU button at the StandardDisplay, select Spot Matchandstart the function usingbutton 4 (fan beam will be activated)..Note:SpotMatchcanalsobestartedviainfraredusingtheRC603.Note:ThedisplayfallsbacktothestandarddisplaywhileaSpotFinderandanglesymbolisashing.TheplumbbeamwillbeautomaticallyalignedtothecenteroftheSF601.4.WhenSpotMatchhasbeencompleted,thefanbeamwillbeturnedoffandtheULcalculatesthegradevaluebetweenbothelevationpoints.ThecalculatedgradevaluewillbedisplayedattheUL‘sandRC‘sdisplay.Note:AutomaticSpotMatchcanbeexitedanytimebypressingandreleasingbutton3(ESC).120432trimble_UL633_01_GB.indd 13 14.04.12 11:40
14Line ScanLine Scan centers the rotor horizontally and can be used to align the plumb beam to a desired horizontalposition.PressandreleasetheMENUbuttonattheStandardDisplayandselectLineScan. Pressing and releasing button 4 activates the Line Scan mode while the rotor checks the limitsoftheX-axisandstopsatthecenterposition.Pressing button 3(ESC)stopsthemovementandchangestheunitintomanualmode.Correctionsupanddowncanbedoneusingbutton5/8;forleft/rightcorrectionsusebutton6/7. Press and release the manual button to change the unit back to full automatic mode.Beam PlungeBeamPlungecenterstherotorverticallyandcanbeusedtoaligntheplumbbeamtoadesiredverticalposition,e.g.,whendoingInteriorlayout.PressandreleasetheMENUbuttonattheStandardDisplayandselectBeamPlunge.Pressingand releasing button 4activatestheBeamPlungemodewhiletherotorchecksthelimitsoftheY-axisandstopsatthecenterposition.Pressing button 3(ESC)stopsthemovementandchangestheunitintomanualmode.Correctionsupanddowncanbedoneusingbutton5/8;forleft/rightcorrectionsusebutton6/7. Press and release the manual button to change the unit back to full automatic mode.Setting MenuPressandreleasetheMENUbuttonattheStandardDisplayandselectSettings.Press and release button 4toopentheSettingMenu;selectthedesiredfunctionthenpressbutton4toopentheselectedsubmenufunctionORstarttheselectedfunction.TheSettingMenuoffersthefollowingfunctions:Pairing Mask Mode Grade Entry Grade Display Sensitivity HI-Alert Information Set Password Password On/Off RF-Channel Select Language PairingWheninSettings,pressandreleasebutton4 to open the Pairing menu. The display shows the currentlypairedunits(uptotworeceiversandtworemotecontrols).Ifalready2remotecontrolshave been paired, one of them has to be deleted using button 1(CLR).TurnontheRC603andselect the Pairing menu and press button 4. TheUL633pairsnowautomaticallywiththenewremotecontrol.120432trimble_UL633_01_GB.indd 14 14.04.12 11:40
15Pairing the transmitter with remote controlThe chain symbol at button 1 indicates the remote has never been paired before which means no radio connectivity is given. Pressing the pairing button 1willinitiateapairingrequest.Thetransmitterhastobeinpairing mode as shown above.Note:Makesurethatpairingmodeisselectedonlyatonetransmitterwhichiswithintheradiorangeoftheremoteduringapairingrequest.Otherwisepairingprocedurecanbeconfused.Pairing the transmitter with receiverTo pair the transmitter and the receiver select Settings and press and release button 4 to open the Pairing menu.Thedisplayshowsthecurrentlypairedunits(upto2receivers).Ifalready2receivershavebeenpaired,one or both of them have to be deleted using button 1(CLR).ABCNext,turnonthereceiverthenpressandholdtheDeadband(A)andtheAudio(B)buttonsfortwoseconds.AftertwosecondsthedisplayshowsMENUrst,thenRDIO.PressandreleasetheUnits(C)button–displayshowsthecurrentradiomode.IfnotalreadysettoUL,pressUnitsbuttonandthenpressDeadbandorAudiobuttonuntilULisdisplayed.PressUnitsbuttonagaintoenterselection.PressandreleasetheAudiobutton–displayshowsPAIR.PresstheUnitsbuttonagain–thedisplayshowsPAIRandarotatingbar.AftercompletingPAIR,OKwillbedisplayed.TheUL633pairsnowautomaticallywiththenewreceiver.PressandreleasethePowerbuttontwotimestoexitthemenu.AlasersymbolislittoconrmthereceiverworksinULmode.Mask modeSelecttheMaskiconandpressandreleasebutton4toopentheMasksettingmenu.Dependingonwhichsideorcornerthebeamshouldbeturnedoff,therequiredsectorcanbeselected.Pressand release the buttons 5 to 8formovingashortashinglinearoundthemaskmodesymbol.Forselectingthesectorwherethebarisashing,pressandreleasebutton1(SET).Aftersettingtherstsector,button1changestoshowCLRwhichofferesthecapabilityofdeletingtheselectedmasksectoragain.Usebutton5 to 8tomovetheashingbartootherrequiredareasandrepeatthesettingprocess.Whenallareashavebeenset,pressbutton 4 to store the mask sector selection until the unit will be turned off. Hinweis: The unit always powers up with the mask mode deactivated (default).120432trimble_UL633_01_GB.indd 15 14.04.12 11:40
16Grade Entry SelecttheGradeEntryiconandpressandreleasebutton4toopentheGradeEntrymenu.Buttons6/7canbeusedtotogglebetweenStepandGoandDigitSelect.Press and release button 4toconrmtheselection.Step and Go Digit SelectGrade DisplaySelecttheGradeDisplayiconandpressandreleasebutton4toopentheGradeDisplaymenu.ThedesiredGradeDisplayMode(Percent/Permille/Degree)canbeselectedusingthebuttons6/7. Press and release button 4toconrmtheselecteddisplaymode.Sensitivity SelectionSelect the Sensitivity icon and press and release button 4 to open the Sensitivity menu. The desiredSensitivity:Low,Mid(Default)andHigh)canbeselectedusingthebuttons6/7. Press and release button 4toconrmtheselectedSensitivity.HI-alert SelectionSelecttheHIiconandpressandreleasebutton 4toopentheHI-alertmenu.ThedesiredHI-alert:5min.(Default),30secondsandHI-Off)canbeselectedusingthebuttons 6/7. Press and release button 4toconrmtheselectedHI-alert.120432trimble_UL633_01_GB.indd 16 14.04.12 11:40
17User NameSelecttheUsernameiconandpressandreleasebutton4toopentheUsernamemenu.Onerowfortypingnamesinbigfont(15)andonerowinsmallfont(18)forlettersornumbersareavailable.Button5 and 8canbeusedtotogglebetweenbothrows.Changingthecharacterscan be done using the buttons 1 and 2. Press and release button 4toconrmtheselectedusername.Thedisplayfallsbacktothemainmenu.Anytimetheunitwillbepoweredup,theUserinfo will be displayed for couple seconds.Set PasswordSelect the Set Password icon and press and release button 4toopenthePasswordmenu.UseButton1 to 8 to type in a password containing of 4 digits and repeat the password at the second row. Press and release button 4tostoretheselectedpassword;unitfallsbacktothestandardmenu.Afterpoweringuptheunit,thestandarddisplaycomesupifthecorrectpasswordwillbeentered, otherwise the unit turns off automatically.Password On/OffSelecttheSetPasswordON-Officonandpressandreleasebutton4 to open the Password menu. Buttons6/7 can be used to toggle between Password On and Password Off if a Password has been entered before. Press and release button 4toconrmtheselection.Password on Password offRadio (RF) Channel SelecttheRFChanneliconandpressandreleasebutton4toopentheRadioChannelmenu.ThedesiredRFChannel:Low,Mid(Default),andHighcanbeselectedusingthebuttons6/7. Press and release button 4toconrmtheselectedRFChannel.120432trimble_UL633_01_GB.indd 17 14.04.12 11:40
18Select LanguageSelect the Language icon and press and release button 4toopentheLanguagemenu.Usebutton5 to 8toselecttherequiredlocallanguage(EN,DE,IT,FR,ES,PT,NL,DA,NO,SV,FI,PL).Press and release button 4tostoretheselectedLanguage;unitfallsbacktothestandardmenu.CALIBRATIONChecking Calibration of the Y- and X-Axes1. Set up the laser 30 m (100 ft) from a wall and allow it to level.2. Setthegradeto0.000%inbothaxes.3. Raise/lowerthereceiveruntilyougetanon-gradereadingforthe+Yaxis.Usingthe on-grade marking notch as a reference, make a mark on the wall.Note: Forincreasedprecision,usethene-sensitivitysetting(1.5mm/1/16in.)onthe receiver.4.Rotatethelaser180°(-Yaxistowardthewall)andallowthelasertore-level.5.Raise/lowerthereceiveruntilyougetanon-gradereadingforthe–Y/axis.Usingtheon-grade marking notch as a reference, make a mark on the wall. 6.Measurethedifferencebetweenthetwomarks.Iftheydiffermorethan3mmat30m(1/8inchat100feet),thelaserneedscalibrating.7.AftercheckingtheY-axis,rotatethelaser90°.Repeattheabovestartingwiththe+Xaxisfacingthewall.Checking Calibration of the Z-(vertical) AxisTo check vertical calibration, you need a plumb bob with at least 10m (30ft) of string.1. Suspend the plumb bob in front of a house i.e., attached to a window frame whose window height is at least 10m (30ft). 2. Set up the laser in vertical so that the laser beam strikes the receiver’s on-grade position at the top of the string.3.Lookforanydeviationusingthereceiverfromthetopofthestringtothebottomofit.Ifthedeviationismorethan1mm(<1/16in.),theverticalaxisneedscalibrating.Note:Ifcalibrationisrequired,please,refertothecalibrationinstructionsonourTrimblewebsitewww.trimble.com/support.shtml.120432trimble_UL633_01_GB.indd 18 14.04.12 11:40
19TroubleshootingAnyerrormessagecanbedeletedwithashortpressofbutton4 (OK). The table shows the related description andpossiblesolutions.Thenextservicecentershouldbecontactedifadifferenterrormessageasshownatthe table will be displayed.Error codes Description Solution21 TemporaryEEpromproblem Repeatpairingandre-enterthecustomer settings120 HIalert-UnitHeigtchanged ChecklaserbeamelevationafterdeletingtheHIalert130 MechanicalLimitduringAxisAlignment,GradeMatchorSpotMatchRe-aligntheclosertothealignmentpoint;checkifexistingslopeisabove+/-25%131 RakeAngleLimit Re-aligntheunitclosertothealignment point 140 Laser beam blocked Makesuretherearenoobstacles between the transmitterandtheHL750orSF601141 Time Out - Function could not be completed in the allowed timeCheckradiooperatingrange/connection;checkstablelasersetup150 Noreceiver-Receivernotavailableforsingleaxisautomatic functionMakesurethereceiverisonandpaired151 Noreceivers-Bothreceiversare not available for automatic alignment functionMakesurebothreceiversareonand paired152 Noreceiver-Thelasersearchedfor the receiver but could not nditChecktheoperatingrangeforauto function and restart the auto alignment153 LostReceiver-Thelasersearched and found the receiver but then lost itChecktheoperatingrangeforauto function and restart the auto alignment160 X,YorZlevelsensordefect Contactservicecenter120432trimble_UL633_01_GB.indd 19 14.04.12 11:40
20SF601 - User GuideSF601attachedtoagraderodusing the standard receiver clamp Components SF601SF601attachedtotheoptional pipe laser target base1. SF6012. Slider 3. CenterHole4. PowerButton5. BubbleVial6. BatteryLED7. ModeLED8. RedDirectionLEDs9. IRtransmitters/receivers10. Markingnotches(frontandback)11. M6ClampMount12. Batterydoor13. LatchforBatteryDoor14. ReleaseTabSlider1011034591076101058121110132214120432trimble_UL633_01_GB.indd 20 14.04.12 11:40
21Powering the SF6011. Open the battery door pulling the battery door latch. TheSF601willbeshippedwithalkalinebatteries. Rechargeablebatteriescanbeusedoptionalbutneedtobechargedexternally2.Insert four AA batteries noting the plus (+) and minus (-) diagrams inside on thebattery door. 3.Closethebatterydoor.Pushdownuntilit“clicks”intothelockedposition.SF601 - Features and Functions1.Power/ModeButton:PressandreleasethepowerbuttontoturnONtheSF601. AlldisplayLED’swilllightfor1.0sec. Pressandholdpowerbuttonfor>1sec.toturnOFFtheSF601.After1sec.alldisplayLED’swilllight1.0sec.Note: Wurde der SF601 eingeschaltet, wird durch kurzes Drücken der Ein-Aus-Taste die Fanbeam-Linseaktiviert/deaktiviert(einevorhergestarteteAutomatikfunktionwirdsofortgestoppt).LED’s: 2. LED1: solidgreenwhenSF601isonandbatteryOKblinkingredifbatteryvoltageis3,8V<Vbat<4Vsolidredifbatteryvoltageis<3,8V;SF601turnsoffautomaticallyafter5min.3. Mode LED2: yellow solid: automatic modeashing:noneorlostsignaloff: manual mode4. Direction LEDs red:Manualmode:pointingtowardsthecenteroftheplumbbeam.All4LEDsaresolidredwhenthebeamiscentered.AutomaticSpotLockmode:solidfor5min.,thenLED’sashevery5seconds.Using the SpotFinder SF601 for vertical UL applications WiththeUL633usingIRconnection,theSF601canbeusedinthreedifferentautomaticmodesAutomatic-SpotAlignment,SpotLokandSpot-Matchandinadditioninamanual/display(SpotSearch)modetodetectthe plumb beam (fan beam).Automatic-Spot Alignment: SF601guidesthebeamtothetargetpointinthehorizontalaxis,whiletheZ-axisgradevaluewillbemaintained.Usedforrstandseconddayalignment(pipelayingapplications).2431120432trimble_UL633_01_GB.indd 21 14.04.12 11:40
22Using SpotLok mode (like PlaneLok) aligns and holds the plumb beam automaticallytotheSF601centerpoint(bothaxes)untilexitingthismode.Automatic-Spot-Match: (like Grade Match- two existing elevation pointswill be connected to measure the grade value between these two points) alignstheplumbbeamautomaticallytotheSF601centerpoint(bothaxes)andmovesback to Z-axis automaticmodewhile displaying the measuredZ-axisgradevalue.Note: WhenAutomaticSpotAlignmentandAutomaticSpot-Matchhavebeencompleted,theUL633turnsoffthefanbeamautomatically.Note:WithaquickpressandreleaseoftheSF601powerbutton,thefanbeamlensattheUL633willbeactivated/deactivatedwhileapreviousactivatedautomodewillbeexited.SF601 – Manual/Display Mode WithaquickpressandreleaseoftheSF601powerbutton,thefanbeamlensattheUL633willbeactivated/deactivatedwhileapreviousactivatedautomaticmodewillbeexited.Manual/Display (Spot Search) mode:Ifthefanbeamlenswill beactivatedandnoautomaticmodehasbeenstarted,theSF601isinmanual/displaymodewheretheREDdirectionLEDsguidetheusertothecenterposition of the fan beam. Note:IRcommunicationisdisabled.ThedirectionLEDsworksimilarlikeusingthepipelasertarget,e.g.,ifthe left top LED is on,theSF601hastobemovedtotheleft/uppositiontobringthecenterholeintothecenterofthebeam.All4 LEDs are solid red when the beam is centered.120432trimble_UL633_01_GB.indd 22 14.04.12 11:40
23PROTECTING THE UNITDonotexposetheunittoextremetemperaturesortemperaturechanges(donotleaveinsidethecar).Theunitisveryrobustandcanresistdamageifdroppedevenfromtripodheight.Beforecontinuingyourwork,alwayscheckthelevelingaccuracy.SeeCheckingCalibrationsection.Thelaseriswaterproofandcanbeused indoors and outdoors.CLEANING AND MAINTENANCEDirtandwaterontheglasspartsoflaserorprismwillinuencebeamqualityandoperatingrangeconsiderably.Cleanwithcottonswabs.Removedirtonthehousingwithalint-free,warm,wetandsmoothcloth.Donotuseharshcleansersorsolvents.Allowtheunittoairdryaftercleaningit.PROTECTING THE ENVIRONMENTThe unit, accessories and packaging ought to be recycled. This manual is made of non-chlorine recycling paper.Allplasticpartsaremarkedforrecyclingaccordingtomaterialtype.Do not throw used batteries into the garbage, water or re. Remove them in compliance with environmental requirements.Hinweis für Kunden in der EUNotice to Our European Union CustomersFor product recycling instructions and more information, please go to:www.trimble.com/environment/summary.htmlRecyclinginEurope:TorecycleTrimbleWEEE, Call+31497532430,andaskforthe“WEEEAssociate”orMailarequestforrecyclinginstructionsto:TrimbleEuropeBVc/oMenloWorldwideLogisticsMeerheide455521DZEersel,NLWarrantyTrimblewarrantstheUL633tobefreeofdefectsinmaterialandworkmanshipforaperiodof5years.Trimbleor its authorized service center will repair or replace, at its option, any defective part, or the entire product, forwhichnoticehasbeengivenduringthewarrantyperiod.Ifrequired,travelandperdiemexpensestoandfromtheplacewhererepairsaremadewillbechargedtothecustomerattheprevailingrates.Customersshould send the product to Trimble Navigation Ltd. or the nearest authorized service center for warrantyrepairsorexchange,freightprepaid.Anyevidenceofnegligent,abnormaluse,accident,oranyattempttorepairtheproductbyotherthanfactory-authorizedpersonnelusingTrimblecertiedorrecommendedparts,automaticallyvoidsthewarranty.Specialprecautionshavebeentakentoensurethecalibrationofthelaser;however,calibrationisnotcoveredbythis warranty.Maintenanceofthecalibration is the responsibility oftheuser.TheforegoingstatestheentireliabilityofTrimbleregardingthepurchaseanduseofitsequipment.Trimblewillnotbeheldresponsibleforanyconsequentiallossordamageofanykind.Thiswarrantyisinlieuofallotherwarranties,exceptassetforthabove,includinganyimpliedwarrantymerchantabilityoftnessfora particular purpose, are hereby disclaimed. Thiswarrantyisinlieuofallotherwarranties,expressedorimplied.120432trimble_UL633_01_GB.indd 23 14.04.12 11:40
24TECHNICAL DATAUL633Leveling accuracy1,3: ±0.5mm/10m,1/16“@100ft,10arcsecondsGrade accuracy1,3: ±1.0mm/10m,1/8“@100ft,20arcsecondsRotation: 0-900rpmScanmode: 5presetsizes+variableadjustmentOperational area1,2: appr. 400 m (1300 feet) radius with detectorLasertype: reddiodelaser650nmLaserclass: Class3A/3R,<5mWSelf-levelingrange: appr.±14°Graderange(Y;X): ±25%bothaxes(notsimultaneously)Graderange(Z): ±25%Levelingindicators: LCDindicationsandLEDashesRadiorange(HL750): upto80m(260ft)Powersource: NiMHbatterypackBatterylife1: 35hoursNiMH;40hoursalkalineOperatingtemp.: -20°Cto50°C(-4°Fto122°F)Storagetemp.: -20°Cto70°C(-4°Fto158°F)Tripodattachments: 5/8x11horizontallyandverticallyDustandWaterproof: IP67Weight: 3.1kg(6.8lbs)Lowvoltageindication: LCDbatteryindicatorLow voltage disconnection: unit shuts off1) at 21°Celsius2) under optimal atmospheric circumstances3) along the axis 4) depending on sun light conditionsRemote Control RC603RadioOperatingrange1,3: up to 100 m (330 ft) IROperatingrange1,4: upto80m(260ft)Powersource: 2x1.5VAAalkalinebatteriesBatterylife1: 130 hoursDustandWaterproof: IP66Weight: 0.26kg(0.4lbs)Spot Finder SF601Operating range1,4: upto80m(260ft)Powersource: 4x1.5VAAalkalinebatteriesBatterylife1 : 30 hoursDustandWaterproof: IP67Weight: 0.43kg(0.4lbs)120432trimble_UL633_01_GB.indd 24 14.04.12 11:40
25DECLARATION OF CONFORMITYPlease disregard the declaration of conformity within the manual.Following is the valid declaration: WeTrimble Kaiserslautern GmbHDeclareunderoursoleresponsibilitythattheproductsUL633 and RC603/SF601 To which this declaration relates is in conformity with the following standards:EN300 440-2 V1.1.1:2004, EN301 489-03 V1.4.1:2002, EN301 489-01 V1.4.1:2002, EN50371:2002, EN60825:1994 + A1:2002 + A2:2001following the provisions of directive R&TTE 1999/5/EC.The managing directorELECTRO-MAGNETIC COMPATIBILITYCompliance statement (part 15.19) This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Warning (part 15.21) Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. This in particular is applicable for the antenna which has been delivered with the UL633 and RC603 Under Industry Canada regulations, this radio transmitter may only operate using an antenna of a type and maximum (or lesser) gain approved for the transmitter by Industry Canada. To reduce potential radio interference to other users, the antenna type and its gain should be so chosen that the equivalent isotropically radiated power (e.i.r.p.) is not more than that necessary for succesful communication. 120432trimble_UL633_01_GB.indd 25 14.04.12 11:40

Navigation menu