Trimble TK14RF RF Module User Manual TI RF integration manual 01

Download:
Mirror Download [FCC.gov]
Document ID	2432324
Application ID	cGfGhxrpXI9GSaHaryB9nA==
Document Description	User Manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	6.94kB (86772 bits)
Date Submitted	2014-10-31 00:00:00
Date Available	2014-10-31 00:00:00
Creation Date	2014-10-15 12:42:08
Producing Software	GPL Ghostscript 9.10
Document Lastmod	2014-10-15 12:42:08
Document Title	TI RF_integration_manual_01
Document Creator	PDFCreator Version 1.7.3
Document Author:	uohler

TI RF Module Integration Manual
This module will be built in only in Trimble
products by Trimble itself. Trimble makes sure
that the maximum voltage is 3.8V.
Pad
P1
P2
P3
P4
P5
P6
P7
P8
P9
P10
Function
Vdd
GND
SPI_IN
SPI_OUT
SPI_CLK
CS_N
Reset
Vreg_EN
GPIO0
GPIO1
The design is based on the CC2520 from Texas Instruments.
•
•
•
•
•
•
•
•
•
•
P1: Vdd supply voltage 1.8 - 3.8V
P2: GND
P3: SO SPI Interface Serial Out
P4: SI SPI Interface Serial In
P5: SPI_CLK SPI Interface Serial clock 8MHz max
P6: CS_N SPI Interface Chip select active low
P7: External Reset pin active low
P8: Vreg_EN when High, digital voltage regulator is active
P9: GPIO0 general purpose digital I/O
P10: GPIO1 general purpose digital I/O
Mounting instruction:
The module could be mounted and connected with a plug connector or could be mounted on a
plastic holder and connected with cable (P1-P10).
Maximum Voltage: 3,8V
Connect the SPI Port to a microcontroller and use the instruction of Texas Instruments to start
running the module.
ID´s:
FCC: PWR-TK14RF
IC: 4131A-TK14RF
Units with this module have to mark on the label with:
Contains FCC ID: PWR-TK14RF
Contains IC: 4131A-TK14RF
Statements:
Changes or modifications not expressly approved by the party responsible for compliance could void
the user's authority to operate the equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference that may cause
undesired operation.
This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to
the following two conditions:
(1) this device may not cause interference, and
(2) this device must accept any interference, including interference that may cause undesired
operation of the device
Le présent appareil est conforme aux CNR d´Industrie Canada applicables aux appareils radio
exempts de licence. L´exploitation est autorisée aux deux conditions suivantes:
(1) l´appareil ne doit pas produire de brouillage, et
(2) l´utilisateur de l´appareil doit accepter tout brouillage radioélectrique subi, même si le
brouillage est susceptible d´en compromettre le fonctionnement.

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.4
Linearized                      : No
Page Count                      : 2
XMP Toolkit                     : XMP toolkit 2.9.1-13, framework 1.6
About                           : uuid:7f3084c1-56b3-11e4-0000-1546b1dac012
Producer                        : GPL Ghostscript 9.10
Keywords                        : ()
Modify Date                     : 2014:10:15 12:42:08+02:00
Create Date                     : 2014:10:15 12:42:08+02:00
Creator Tool                    : PDFCreator Version 1.7.3
Document ID                     : uuid:7f3084c1-56b3-11e4-0000-1546b1dac012
Format                          : application/pdf
Title                           : TI RF_integration_manual_01
Creator                         : uohler
Description                     : ()
Author                          : uohler
Subject                         : 

EXIF Metadata provided by EXIF.tools