Troybilt 31AH9V75063 User Manual SNOW THROWER Manuals And Guides L0401087

TROYBILT Snowthrower, Gas Manual L0401087 TROYBILT Snowthrower, Gas Owner's Manual, TROYBILT Snowthrower, Gas installation guides

User Manual: Troybilt 31AH9V75063 31AH9V75063 TROYBILT SNOW THROWER - Manuals and Guides View the owners manual for your TROYBILT SNOW THROWER #31AH9V75063. Home:Lawn & Garden Parts:Troybilt Parts:Troybilt SNOW THROWER Manual

Open the PDF directly: View PDF .
Page Count: 28

Download
Open PDF In Browser	View PDF

OTRO_ BILT__
Operator's Manual
Snow Thrower Model
10530mPolar Blast

IMPORTANT:
WARNING:

READ SAFETY

RULES AND INSTRUCTIONS

This unit is equipped with an internal combustion

covered, brush-covered

or grass-covered

CAREFULLY

engine and should not be used on or near any unimproved

forest-

land unless the engine's exhaust system is equipped with a spark arrester meeting applicable local

or state laws (if any). If a spark attester is used, it should be maintained in effective working order by the operator, in the State of California the
above is required by law (Section 4442 of the California Public Resources Code). Other states may have similar laws. Federal laws apply on
federal lands. A spark arrester for the muffler is available through your nearest engine authorized service dealer or contact the service
department, P.O. Box 361 t 31 Cleveland, Ohio 44136-0019.

TROY-BILT

PRINTED IN U.S.A.

LLC, P.O. BOX 361131 CLEVELAND,

OHIO 44136-0019
FORM NO. 769-00293
(6/2002)

TABLEOFCONTENTS
Content

Page

Important Safe Operation Practices ........................................................................

Loose Parts & Hardware Pack .................................................................................

Assembling Your Snow Thrower .............................................................................

Know Your Snow Thrower .......................................................................................

Operating Your Snow Thrower ................................................................................

Making Adjustments ................................................................................................

Maintaining Your Snow Thrower .............................................................................

Service ....................................................................................................................

Off-Season Storage .................................................................................................

Troubleshooting

......................................................................................................

Parts List .................................................................................................................

FINDINGMODELNUMBER
This Operator's Manual is an important part of your new snow thrower. It will help you assemble, prepare and
maintain the unit for best performance. Please read and understand what it says.
copy the information from it in the space provided below. The information on the model plate is very
Before you start assembling your new equipment, please locate the model plate on the equipment and
important if you need help from our Customer Support Department or an authorized dealer.
You can locate the model number by standing behind the unit in the operating position and looking down at the rear
frame below the engine. A sample model plate is explained below. For future reference, please copy the model
number and the serial number of the equipment in the space below.

Mode! Number)

(Serial Number)

Copy the model number here:

Copy the serial number here:
www.troybilt.com

CLEVELAND,
OH_136
330-558-7220
866-840-6483

ENGINEINFORMATION
The engine manufacturer is responsible for all engine-related issues with regard to performance, power-rating,
specifications, warranty and service. Please refer to the engine manufacturer's Owner's/Operator's Manual packed
separately with your unit for more information.

CALLINGCUSTOMER
SUPPORT
Please do NOT return theunit to the retailer from whichit waspurchased, withoutfirst contactingCustomerSupport.
Should you have difficulty assembling this product or have any questions regarding the controls, operation or
maintenance of this unit, please call the Customer Support Department.
Call 1- (330) 558-7220 or 1- (866) 840-6483 to reach a Customer Support representative. Please have
your unit's model number and serial number ready when you call. See previous section to locate this
information. You will be asked to enter the serial number in order to process your call.

SECTION1: IMPORTANT
SAFEOPERATION
PRACTICES
This symbol points out important safety instructions, which if not followed, could endanger the personal
safety and/or property of yourself and others. Read and follow all instructions in this manual before
attempting to operate this machine. Failure to comply with these instructions may result in personal
injury. When you see this symboliheed
its warning.
WARNING:
Engine Exhaust, some of its constituents,
contain or emit chemicals known to the State of California
other reproductive harm.

and certain vehicle components
to cause cancer, birth defects or

DANGER:

This machine was built to be operated according to the rules for safe operation in this
manual. As with any type of power equipment, carelessness or error on the part of the operator can
result in serious injury. This machine is capable of amputating hands and feet and throwing objects.
Failure to observe the following safety instructions could result in serious injury or death.

TRAINING
1.

4.
5.

Read, understand, and follow all instructions on the
machine and in the manual(s) before attempting to
assemble and operate. Keep this manual in a safe place
for future and regular reference and for ordering
replacement parts.
Be familiar with all controls and their proper operation.
Know how to stop the machine and disengage them
quickly.
Never allow children under 14 years old to operate this
machine. Children 14 years old and over should read and
understand the operation instructions and safety rules in
this manual and should be trained and supervised by a
parent.
Never allow adults to operate this machine without proper
instruction.
Thrown objects can cause serious personal injury. Plan
your snow4hrowing pattern to avoid discharge of material
toward roads, bystanders and the like.
Keep bystanders, helpers, pets and children at least 75
feet from the machine while it is in operation. Stop
machine if anyone enters the area.
Exercise caution to avoid slipping or falling, especially
when operating in reverse.

PREPARATION
1.

4.
5.

Thoroughly inspect the area where the equipment is to be
used. Remove all doormats, newspapers, sleds, boards,
wires and other foreign objects, which could be tripped
over or thrown by the auger/impeller.
Always wear safety glasses or eye shields during
operation and while performing an adjustment or repair to
protect your eyes. Thrown objects which ricochet can
cause serious injury to the eyes.
Do not operate without wearing adequate winter outer
garments. Do not wear jewelry, long scarves or other
loose clothing, which could become entangled in moving
parts. Wear footwear which will improve footing on
slippery surfaces.
Use a grounded three-wire extension cord and
receptacle for all units with electric start engines.
Adjust collector housing height to clear gravel or crushed
rock surfaces.

Disengage all clutch levers before starting the engine.
Never attempt to make any adjustments while engine is
running, except where specifically recommended in the
operator's manual.
Let engine and machine adjust to outdoor temperature
before starting to clear snow.
To avoid personal injury or property damage use extreme
care in handling gasoline. Gasoline is extremely
flammable and the vapors are explosive. Serious
personal injury can occur when gasoline is spilled on
yourself or your clothes, which can ignite. Wash your skin
and change clothes immediately.
a. Use only an approved gasolinecontainer.
b. Extinguish all cigarettes, cigars, pipes and other
sources of ignition.
c. Never fuel machine indoors.
d. Never remove gas cap or add fuel while the
engine is hot or running.
e. Allow engine to cool at least two minutes before
refueling.
f.
Never over fill fuel tank. Fill tank to no more than _/2
inch below bottom of filler neck to provide space
for fuel expansion.
g. Replace gasoline cap and tighten securely.
h. If gasoline is spilled, wipe it off the engine and
equipment. Move machine to another area. Wait 5
minutes before starting the engine.
i.
Never store the machine or fuel container inside
where there is an open flame, spark or pilot light
(e.g. furnace, water heater, space heater, clothes
dryer etc.).
j.
Allow machine to cool at least 5 minutes before
storing.

OPERATION
1.

Do not put hands or feet near rotating parts, in the auger/
impeller housing or discharge chute. Contact with the
rotating parts can amputate hands and feet.
The auger/impeller clutch lever is a safety device. Never
bypass its operation. Doing so makes the machine
unsafe and may cause personal injury.
The clutch levers must operate easily in both directions
and automatically return to the disengaged position when
released.

4. Never
operate
witha missing
ordamaged
discharge
Contact
yourdealerortelephone
I (866)840-6483
for
chute.Keepallsafety
devices
inpieceandworking.
assistance
andthename
ofyournearest
servicing
dealer.
5. Never
runanengine
indoors
orinapoorly
ventilated
area.Engine
exhaust
contains
carbon
monoxide,
an
odorless
anddeadly
gas.
MAINTENANCE
ANDSTORAGE
6. Donotoperate
machine
whileundertheinfluence
of
1. Never tamper with safety devices. Check their proper
alcohol
ordrugs.
operation regularly. Refer to the maintenance and
7. Muffler
andengine
become
hotandcancause
aburn.Do
adjustment sections of this manual.
nottouch.
2.
Before cleaning, repairing or inspecting machine
8. Exercise
extreme
caution
whenoperating
onorcrossing
disengage all clutch levers and stop engine. Wait until the
gravelsurfaces.
Stayalertforhidden
hazards
ortraffic.
auger/impeller come to a complete stop. Disconnect the
9. Exercise
caution
whenchanging
direction
andwhile
spark plug wire and ground against the engine to prevent
operating
onslopes.
unintended starting.
10. Planyour
snow-throwing
pattern
toavoiddischarge
3. Check bolts and screws for proper tightness at frequent
towards
windows+
wails,carsetc.Thus,avoiding
intervals to keep the machine in safe working condition.
possible
property
damage
orpersonal
injurycaused
bya
Also, visually inspect machine for any damage.
ricochet.
4.
Do not change the engine governor setting or over-speed
11. Never
directdischarge
atchildren,
bystanders
andpets
the engine. The governor controls the maximum safe
orallowanyone
infrontofthemachine.
operating speed of the engine.
12. Donotoverload
machine
capacity
byattempting
toclear
5.
Snow thrower shave plates and skid shoes are subject to
snowattoofastofa rate.
wear and damage. For your safety protection, frequently
13. Never
operate
thismachine
without
goodvisibility
or
check all components and replace with original
light.Always
besureofyourfooting
andkeepafirmhold
equipment manufacturer's (OEM) parts only. "Use of
onthehandles.
Walk,neverrun.
parts which do not meet the original equipment
14. Disengage
power
totheauger/impeller
when
specifications may lead to improper performance and
transporting
ornotinuse.
compromise safety!"
15. Never
operate
machine
athightransport
speeds
on
6. Check dutch controls periodically to verify they engage
slippery
surfaces.
Lookdownandbehind
andusecare
and disengage properly and adjust+ if necessary. Refer to
wheninreverse.
the adjustment section in this operator's manual for
16. Ifthemachine
should
starttovibrate
abnormally,
stopthe
instructions.
engine,
disconnect
thesparkplugwireandground
it
7.
Maintain or replace safety and instruction labels, as
against
theengine.
Inspect
thoroughly
fordamage.
necessary.
Repair
anydamage
before
starting
andoperating.
8.
Observe proper disposal laws and regulations for gas,
17. Disengage
allclutch
levers
andstopengine
before
you
oil, etc. to protect the environment.
leavetheoperating
position
(behind
thehandles).
Wait
untiltheauger/impeller
comes
toacomplete
stopbefore 9. Prior to storing, run machine a few minutes to clear snow
from machine and prevent freeze up of auger/impeller.
unclogging
thedischarge
chute,making
any
10+
Never store the machine or fuel container inside where
adjustments,
orinspections.
there is an open flame, spark or pilot light such as a water
18. Never
putyourhandinthedischarge
orcollector
heater, furnace, clothes dryer etc.
openings.
Always
usetheclean-out
toolprovided
to
11.
Always refer to the operator's manual for proper
unclog
thedischarge
opening.
Donotunclog
discharge
instructions on off-season storage.
chutewhileengine
isrunning.
Shutoffengine
andremain
behind
handles
untilallmoving
partshavestopped
WARNING-- YOURRESPONSIBILITY:
before
unclogging.
Restrict the use of this power machine to persons who
19. Useonlyattachments
andaccessories
approved
bythe
understand and follow the warnings and
manufacturer
(e.g.wheelweights+
tirechains,
cabsetc.). read,
instructions
in this manual and on the machine. The
20. Ifsituations
occurwhicharenotcovered
inthismanual+
safety
labels
are shown below for your reference.
usecareandgoodjudgment.

1.10_ AWAYFROMROTATING
IMPELLI_
ANDAUGBR.
CgHTACT
WT'C4
IN_LLEROR
ALiBRCJ ,Z,_UTATO
HANDS
ANDH£i:'r,
2. USECLFJLN-C(IT
TOOLTOUNCLOG
DI$CILIRGE$HUIT.

_b
_

S.glSEHGAOE
LEIERS5"FOr
ETOiHE,
.MIDHmNNCLUTOH
gEHifOFIAHDLE$
UN111.
N.L
i40VIHIG
PARTSHAVE
STOPPWDETOHE
UNCLOGGING
ORS_VICING MACHINE.
4.TO AVDID11TOOWH
OBJECTS
INJURIES,
iWR DIRECT
DISCIIARGE
ATDTSTANDERS.
LBSE
e('l_,ACALmON
WHENOFHTAllNG
ON
GRAVELSURW_CES.
. R_D OPmATOR'$MAHLBAL.
I:l,EF,I- liJT 1TIP. iala4aili,

SECTION2: ASSEMBLING
YOURSNOWTHROWER
NOTE:

All references to right or left side of the snow
thrower are determined from behind the unit in the
operating position. The "operator's position" is defined
as standing directly behind the snow thrower, facing the
handle panel

LooseParts
•

The augers are secured to the auger shaft with two
shear bolts and hex lock nuts. If you hit a foreign
object or ice jam, the snow thrower is designed so
that the bolts may shear. Two replacement shear
bolts and nuts are provided for your convenience.
Store in a safe place until needed. See Figure 1.
__Shear

Bolts

_Hex
_/Nuts

Wing Nut

Lock

Figure 2
Figure 1
IMPORTANT: NEVER replace the auger shear bolts with
standard hex bolts. Any damage to the auger gearbox
or other components from standard hex bolts will not be
covered by your snow thrower's warranty.

AssemblingHandle
_,

Shift Rod
Connector

wire
and groundDisconnect
it against the
the spark
engineplug
to
WARNING:
prevent unintended starting.

Carriage

IMPORTAWr: Make any adjustments, as instructed on
Page 10, before operating your snow thrower. Failure
to follow these instructions may cause damage to the
snow thrower.
•

\Bell

Remove the lower plastic wing nut, cupped washer
and carriage bolt from each side of the lower
handle. See Figure 2.

•

Pivot the upper handle assembly forward until it
locks over the lower handle. See Figure 2.
Secure the upper handle and lower handle with the
two plastic wing nuts, bell washers and carriage
bolts previously removed from the lower hole.
Firmly tighten all four wing nuts to secure the upper
handle to the lower handles.

Washer

Wing Nut

Springs

Actuator Brackets

NOTE: Before proceeding, look at the lower rear of the
snow thrower frame to be sure the spring (found at the
end of each cable) is attached to its actuator bracket
See Figure 3.
•

Bolt

Figure 3
•

Slide the shift rod connector down over the end of
the lower shift rod. Tap the connector until it locks
over the lower shift rod. See Figure 3.

NOTE: If the connector is not properly assembled, the
shift rod will pivot and you will not be able to change
speeds or change directions.

AttachingChuteDirectionalControl
•

•

Cable Guide

Discharge Chute

Remove the hairpin clip from the upper rod and
slide the upper rod through the bracket and into the
lower rod. See Figure 4.
Align the two holes on both chute cranks and insert
the hairpin clip removed earlier, through these
holes. See Figure 4.
Upper Chute Crank

Figure
_

Upper Chute
Crank Bracket

III
-Alternator

I
Lead

Hairpin Clip
Lower Chute Crank

Figure 4

RoutingChuteTilt Cables
•

If not already routed, slip the cables that run from
beneath the handle panel to the discharge chute
through the cable guide located on top of the
engine housing. See Figure 5.

Lamp Wire

Connecting
AlternatorLead
•

Unwrap the headlight wire which is attached to the
headlights, beneath the handle panel. Wind the
wire around the lower right handle until excess
slack is removed. See Figure 6.

Figure 6
Plug the wire from the headlight into the alternator
lead located on the right side of the engine,
beneath the fuel tank. See Figure 6.

SECTION3: KNOWYOURSNOWTHROWER
Skid Shoes
,_

all
instructions and
warnings
on theand
machine
WARNING:
Read,
understand,
follow
and in this manual before operating.

ChuteTilt Control
The distance snow is thrown can be changed by
adjusting the angle of the chute assembly. Move the
chute tilt control forward to decrease the distance,
toward the rear to increase. See Figure 7.
DischargeChute
The angle of the discharge chute controls the distance
that the snow is thrown. Tilt the discharge chute up for
greater distance; tilt down for less distance.

The space between the shave plate and the ground can
be adjusted by positioning the skid shoes. Refer to Skid
ShoeAdjustment
on page 11.
Throttle Control
The throttle control is located on the engine. It regulates
the speed of the engine. See Figure 7.
Safety IgnitionKey
The ignition key must be inserted in the switch in order
for the engine to start. Remove the ignition key when
the snow thrower is not in use.
NOTE: Do NOT "turn" the ignition key in an attempt to
start the engine.

Traction Control /
Auger Control Lock

,Shift Lever
Chute Tilt Control
Auger Control

Fuel Tank
Discharge

Chute Directional Control

Chute
Clean-out Tool

Left Wheel Steering Control
(Right Control Not Visible)

Electric
Starter
3utton

Primer.x

Switch
Box

Safety Ignition Ke_

Auger

Recoil
Starter
Handle

Throttle Control

Skid Shoe

Figure 7
Shift Lever
The shift lever is located in the center of the handle
panel and is used to determine ground speed and
direction of travel. It can be moved into any of eight
positions. See Figure 7.
IMPORTAhrI":Always release traction the control before
changing speeds.
Forward
Your snow thrower has six forward (F) speeds.
Position number one (1) is the slowest and position
number six (6) is the fastest.
Reverse
Your snow thrower has two reverse (R) speeds. R1 is
the slower, while R2 is the faster of the two.
Tract0n Control/ Auger ControlLock
The traction control is located on the right handle.
Squeeze the traction control to engage the wheel drive.
Release to stop. See Figure 7.
This same lever also locks the auger control lock, so
you can operate the chute crank without interruptingthe
snow throwing process. If the auger control is engaged
simultaneously with the traction control, the operator
can release the auger control (on the left handle) and
the augers will remain engaged. Release the traction
control to stop both the augers and wheel drive (the
auger control must also be released).
IMPORTANT: ALWAYS release the traction control
before moving the shift lever. Failure to do so will result
in premature wear to the drive system's friction wheel.

AugerControl
The auger control is located on the left handle.
Squeeze the auger control to engage the augers.
Release to stop the snow throwing action. The traction
control must also be released in order to stop the auger.
IMPORTANT: Refer to AugerControlTeston page 9 prior to
operating your snow thrower. Read and follow all
instructions carefully and perform all adjustments to
verify your snow thrower is operating safely and
properly.
ChuteDirectional Control
The chute directional control is located on left hand side
of the snow thrower.To change the direction which
snow is thrown, rotate chute directional control as
follows:
•
•

Clockwise to discharge to the left.
Counterclockwise to discharge to the right.

Chute Clean-0ut T001
WARNING:
Never use your hand to clear a
clogged discharge chute. Shut off engine and
remain behind handles until all moving parts
have stopped before unclogging.
This item is fastened with a cable tie to the rear of
the Auger Housing at the factory. Cut the cable tie
before operating the snow thrower.
The chute clean-out toot (see Figure 7) is designed to
clear a clogged discharge chute. Refer to page 10 for
detailed instructions on how to properly use the chute
clean-out tool.

Wheel SteeringControls

•

The left and right wheel steering controls are located on
the underside of the handles and are used to assist in

Headlights

steering the snow thrower.
•

Squeeze the right wheel steering control when
turning right; squeeze the left control when turning
left.

Operate the snow thrower in open areas until
becoming familiar with these controls.

When properly connected, both headlights illuminate
whenever the engine is running.

SECTION4: OPERATING
YOURSNOWTHROWER
BeforeStarting

ElectricStarter
•

all
instructions and
warnings
on theand
machine
WARNING:
Read,
understand,
follow
and in this manual before operating.

WARNING:

Service the engine with gasoline and oil as
instructed in the separate engine manual packed with
your snow thrower. Read instructions carefully.

handling
extremely
WARNING:gasoline.
Use Gasoline
extreme iscare
when
flammable and the vapors are explosive.
Never fuel machine indoors or while the

•

engine
is hot or running.
Extinguish
cigarettes, cigars, pipes an other sources of
ignition.

•

A plastic cap is provided inside the fuel fill opening
on the fuel tank. Remove and discard this cap
before filling up the tank. Use the separate fuel tank
cap to close after fill-up.

•

ToStartEngine
NOTE: If unit shows any sign of motion (drive or
augers) with the clutch grips disengaged, shut engine
off immediately. Readjust as instructed on page 9-AugerControlTest) and page /O--Traction Controland Shift
Lever.
•

•
•

Attach spark plug wire to spark plug. Make certain
the metal loop on end of the spark plug wire (inside
the boot) is fastened securely over the metal tip on
the spark plug.
Make certain the auger and drive clutch levers are
in the disengaged (released) position.
Move throttle control up to FAST position. Insert
ignition key into slot. See Figure 7. Be certain it
snaps into place. Do not turn key.

NOTE:

Engine will not start unless ignition key is
inserted into ignition slot in carburetor cover.

The

electric

starter

equipped with a grounded three-wire power
cord and plug and is designed to operate on
120 volt AC household current. It must be
used with a properly grounded three-prong
receptacle at all times to avoid the possibility
of electric shock. Follow all instructions
carefully prior to operating the electric starter.

GasAndOilFill-up

Determine that your house wiring is a three-wire
grounded system. Ask a licensed electrician if you
are not certain.

•
•

•

If your house wiring system is not a three-wire
grounded system, do not use this electric starter
under any conditions.
If your home electrical system is grounded, but a
three-hole receptacle is not available, one should
be installed by a licensed electrician before using
the electric starter.
If you have a grounded three-prong receptacle,
proceed as follows:
Rotate choke knob to OFF position and do NOT
prime engine.
Connect power cord to switch box on engine. Plug
the other end of power cord into a three-hole,
grounded 120 volt AC receptacle.
Push the electric starter button (Refer to Figure 7)
to crank engine. As you crank the engine, move
choke knob to FULL choke position.
When engine starts, release starter button, and
move choke gradually to OFF. If engine falters,
move choke immediately to FULL and then
gradually to OFF.
When disconnecting the power cord, always unplug
from the three-prong receptacle first and then from
the snow thrower.

RecoilStarter
•

•

Rotate choke knob to FULL choke position (cold
engine start). If engine is warm, place choke in OFF
position instead of FULL.
Push primer button two or three times. If engine is
warm, push primer button once only.

NOTE: Always cover vent hole in primer button when

•

pushing. Additional priming may be necessary for first
start if temperature is below 15°F.
•

•

Grasp starter handle and pull rope out slowly, until
it pulls slightly harder. Let rope rewind slowly.
Pull starter handle rapidly. Do not allow handle to
snap back. Allow it to rewind slowly while keeping a
firm hold on the starter handle.

•

Repeat the previous steps until engine starts.

•

ToStopEngine
•
•

Run engine for a few minutes before stopping to
help dry off any moisture on the engine.
To help prevent possible freeze-up of starter,
proceed as follows.

Electric Starter:
•

Connect power cord to switch box on engine, then
to 120 volt AC receptacle. With the engine running,
push starter button and spin the starter for several
seconds. The unusual sound made by spinning the
starter will not harm engine or starter. Disconnect
the power cord from receptacle first, and then from
switch box.

•

In a well-ventilated area, start the snow thrower
engine as instructed earlier in this section under the
heading StartingEngine.Make sure the throttle is set
in the FAST position.
While standing in the operator's position (behind
the snow thrower) engage the auger.
Allow the auger to remain engaged for
approximately ten (10) seconds before releasing
the auger control. Repeat this several times.
With the engine running in the FAST position and
the auger control lever in the disengaged "up"
position, walk to the front of the machine.
Confirm that the auger has completely stopped
rotating and shows NO signs of motion.

IMPORTANT: If the auger shows ANY signs of rotating,
immediately return to the operator's position and shut
off the engine. Wait for all moving parts to stop before
readjusting the auger control cable.
•

To readjust the control cable, unhook the spring
(found on the end of the auger cable) from the
auger actuator bracket. See Figure 8.

Recoil Starter
•

With engine running, pull starter rope with a rapid,
continuous full arm stroke three or four times.

Pulling the starter rope will produce a loud clattering
sound, which is not harmful to the engine or starter.
•
Move throttle control to "stop" or "off" position.
•
Remove ignition key. Do not turn key. Disconnect
the spark plug wire from the spark plug to prevent
accidental starting while equipment is unattended.
Wipe all snow and moisture from the carburetor cover
in the area of the control levers. Also, move control
levers back and forth several times.

ToEngageAugers
•

To engage augers and start throwing snow,
squeeze the auger control against the left handle.
Release to stop the augers.

Auger ControlTest

Auger
Spring

Figure 8
Push the cable coupler through the end of the
springto expose the lock nut. See Figure 9.
Coupler

IMPORTANT: Perform the following test before
operating the snow thrower for the first time and at the
start of each winter season.
Check the adjustment of the auger control as follows:
•

Auger
Actuator Bracket

Spring

Cable

When the auger control is released and in the
disengaged "up" position, the cable should have
very little slack, but should NOT be tight.

Lock Nut

Figure 9

Over-tightening Do
may
the auger
from
WARNING:
not prevent
over-tighten
the cable.
disengaging and compromise the safety of the
snow thrower.

Thread the lock nut outward (down the coupler)
three full turns to provide more slack in the cable
and reattach the spring to the bracket.

RepeatAugerControlTesttoverifyproper
adjustment
hasbeenachieved.Repeatthe
previousstepstoprovidemoreslackinthecable,in
necessary.

2.
3.
4.

ToEngageWheelDrive
•

WARNING:

With the engine running near top speed, move the
shift lever into one of the six FORWARD positions
or two REVERSE positions. Select a speed
appropriate for the snow conditions.
5,

Use slower speeds in heavy conditions and
until you are familiar and comfortable with the operation
of the snow thrower.

Squeeze the traction control against the right
handle and the snow thrower will move. Release it
and the drive motion wilt stop.

IMPORTANT: NEVER move the shift lever without first

and
the surrounding
areas may
WARNING:
The temperature
of the exceed
muffler
150°F. Avoid these areas.

Wheel SteeringControls
The left and right wheel steering controls are located on
the underside of the handles.

•

With the traction control engaged, squeeze the
right wheel steering control to assist in turning right;
squeeze the left control to assist in turning left.

•

ChuteClean-outTool

•
•
•

The chute clean-out tool is conveniently fastened to the
rear of the auger housing with a mounting clip (Refer to
Figure 7). If the discharge chute becomes clogged
during operation, proceed as follows to safely clean the
chute and chute opening:
1.

Refasten the clean-out tool to the mounting clip on
the rear of the auger housing, re-start the engine.
While standing in the operator's position (behind
the snow thrower), engage the auger clutch lever
for a few seconds to clear any remaining snow or
ice from the discharge chute before continuing to
clear snow.

OperatingTips

releasing the traction control. Doing so will cause
premature wear to the drive system's friction wheel.

•

Never use your hand to clear a

clogged discharge chute. Shut off engine and
remain behind handles until all moving parts
have stopped before unclogging.

NOTE:

•

Stop the engine by removing the ignition key.
Remove the clean-out tool from the clip which
secures it to the rear of the auger housing.
Use the shovel-shaped end of the clean-out tool to
remove any snow and ice in the discharge chute.

Allow the engine to warm up for a few minutes. The
engine will not develop full power until it reaches
operating temperature.
For the most efficient snow removal, remove snow
immediately after it falls.
Discharge the snow downwind whenever possible.
Slightly overlap each previous path.
Set the skid shoes 1/4" below the shave plate for
normal usage. The skid shoes may be adjusted
upward (to lower the shave plate) for hard-packed
snow. Adjust downward (to raise the shave plate)
when using on gravel or crushed rock.

Release both the Auger Control Lever and the
Traction/Auger Control Lock Lever.

SECTION5: MAKINGADJUSTMENTS
•

Move the shift lever into the fast reverse (R2)
position and repeat the previous two steps.
If you experienced resistance rolling the unit, either
when repositioning the shift lever from 6 to R2 or when
attempting to move the machine with the traction
control released, adjust the traction control
immediately. To adjust, proceed as follows:

chute or make any
adjustments
WARNING:
NEVER
attemptwhile
to engine
clean
is running.
Traction Controland Shift Lever
To check the adjustment of the traction control and shift
lever, proceed as follows:
•
•

•

Move the shift lever into sixth (6) position.
With the traction control released, push the snow
thrower forward, then pull it back. The machine
should move freely.
Engage the traction control and attempt to move
the machine both forward and back, resistance
should be felt.

•

To readjust the control cable, unhook the traction
spring (found on the end of the traction control
cable) from the traction actuator bracket. See
Figure 8.
Push the cable coupler through the end of the
spring to expose the lock nut. See Figure 9.

•

Thread the lock nut outward (down the coupler)
three full turns to provide more slack in the cable
and reattach the spring to the bracket.
•
Check the adjustment of the traction control as
instructed earlier. Repeat the previous steps to
provide more slack in the cable, in necessary.
If you are uncertain that you have reached the correct
adjustment, proceed as follows:

•
•

•

•
•
•

Remove the hairpin clip and flat washer from the
shift handle under the handle panel.
Place shift lever in sixth (6) position (fastest forward
speed).
Push shift arm assembly down as far as it will go.
Rotate the ferrule up or down on the shift rod as
necessary until the ferrule lines up with the upper
hole in the shift lever. See Figure 11.
Shift Lever

snow
thrower's Drain
engine,
place out
a piece
of
WARNING:
the and
gasoline
of your
plastic film under the gas cap to avoid spillage
before beginning the job.

•

Tip the snow thrower forward, allowing it to rest on
the auger housing.
Remove the frame cover underneath the snow

Hairpin Clip &
Flat Washer

thrower by removing six self-tapping screws.
With the traction control released, make sure there
is clearance between the friction wheel and the
drive plate in all positions of the shift lever.
With the traction control lever engaged, make sure
the friction wheel solidly contacts the drive plate.
See Figure 10.

Shift Arm

Ferrule

\
Clutch Rod
Connector

Trigger Cables
Shift Arm \
Auger Actuator
Bracket

Drive Actuator
Bracket

Rod
Figure 11
•

Hex Nut
And Cupped
Washer \

•

Hex Gear Shaft

Insert ferrule from the left side of the snow thrower
into the upper hole.
Reinstall the hairpin clip and the washer.

NOTE:

Make certain to check for correct adjustment
of the shift rod as instructed on page lO--Tractien Contrel
andShift Leverbefore operating the snow thrower.

)

AugerControl
Refer to AugerControlTest on page 9 to adjust the auger
control. Make certain to check for correct adjustment
as instructed before operating the snow thrower.

Rubber
"_ Friction
Wheel
\ Drive Plate

ChuteAssembly
The distance snow is thrown can be adjusted by
adjusting the angle of the chute assembly. Refer to
ChuteTilt Controlon page 6.

Figure 10
If adjustment is necessary, adjust traction control as
instructed below:
•

•
•

The remote chute control cables have been preadjusted at the factory. Move the remote chute lever on
the control panel back and forward to adjust angle of
the chute assembly.

Thread the lock nut outward (down the coupler) to
provide more slack in the cable or thread the lock
nut inward (up the coupler) to provide less slack in
the cable. Refer to Figure 9
Reattach the spring to the bracket.
Reassemble the frame cover.

Tire Pressure(Pneumatic Tires)
The tires are overinflated for shipping purposes.
•

NOTE: If you placed plastic film under the gas cap, be
certain to remove it before operating the snow thrower.

Check the tire pressure before operating the snow
thrower. Refer to the tire side wall for tire
manufacturer's recommended psi and deflate (or
inflate) the tires as necessary.

Shift Rod
If your snow thrower is not achieving its full range of
speeds, the shift rod is in need of adjustment. To adjust
the shift rod, proceed as follows:

NOTE: If the tire pressure is not equal in both tires, the
unit may pull to one side or the other.

WARNING:

Maximum tire pressure under
any circumstance is 30 psi. Equal tire pressure
should be maintained at all times. Excessive
pressure (over 30 psi) when seating beads
may cause tire/rim assembly to burst with
force sufficient to cause serious injury
Skid ShoeAdjustment
The space between the shave plate and the ground can
be adjusted by raising or lowering the skid shoes.
For close snow removal, as when using on a smooth
concrete or asphalt driveway, place the skid shoes in
the low position. Use the middle or high position when
the area to be cleared is uneven. When operating on
gravel, always put skid shoes in the high position.
See Figure 12.

Hex Nuts
Skid
Shoes

Adjust skid shoes as follows:
•
•
•
•

Figure 12

Loosen, but do not remove, the three hex nuts
which fasten the skid shoe to the auger housing.
Raise or lower the skid shoe to desired position.
Retighten the hex nuts loosened earlier.
Repeat on the other side of the snow thrower.

NOTE: Make certain the bottom surface of skid shoe is
flat against the ground to avoid uneven wear

SECTION6: MAINTAININGYOURSNOWTHROWER
WARNING:

Before lubricating, repairing, or
inspecting, disengage all clutch levers and
stop engine. Wait until all moving parts have
come to a complete stop. Disconnect the
spark plug wire and ground it against the
engine to prevent unintended starting.

Vent Plug

\\_.._

Grease Fitting

GeneralRecommendations
•

Always observe safety rules when performing any
maintenance.

•

The warranty on this snow thrower does not cover
items that have been subjected to operator abuse
or negligence.
Some adjustments will have to be made
periodically to maintain your unit properly.
All adjustments in the service and adjustments
sections of this manual should be checked at least
once each season.

•
•

Grease
Fitting

/
G_ta:;
Be _rmgs
" "
Shear Bolt
Shear Bolt
Figure 13

Follow the maintenance schedule given below.
Periodically check all fasteners and hardware to
make sure these are tight.

•

Grease fittings can be found at either end of the
auger shaft. Lubricate with a grease gun once a
season. See Figure 13.

GearCase

Lubrication

The auger gear case is equipped with a grease fitting.
Lubricate with Shell Alvania lead-free grease once a
season (order part number 737-0168). See Figure 13.

Auger Shaft
•
At least once a season, remove the shear bolts
from the auger shaft and spray lubricant inside the
shaft. See Figure 13.

IMPORTANT:To relieve pressure, always remove the
vent plug before lubricating the gear case. Failure to do
so could result in damage to the gear case seals.

DischargeChute
The base of the discharge chute and the spirals on the
chute crank should be lubricated at least every 25
hours of use. Apply the lubricant under the base of the
chute and where the spirals contact the discharge
chute. See Figure 14.

nel

Chute Crank Spirals

Contro/IRods

Lube Cams Here

Figure 15
Engine
Refer to the separate engine manual packed with your
unit for all engine lubrication instructions.

Lube Under Chute Base

:Yll Y

CheckFrictionWheelRubber
Figure 14

Follow the instructions below to check the condition of
the friction wheel rubber every 25 hours of operation.

Drive and ShiftingMechanism
At least once a season or after every 25 hours of
operation, remove rear cover. Lubricate any chains,
sprockets, gears, bearings, shafts, and the shifting
mechanism at least once a season. Use engine oil or a
spray lubricant. Avoid getting oil on rubber friction
wheel and aluminum drive plate. Refer to Figure 10.

•

Remove the six self-tapping screws from the frame
cover underneath the snow thrower.

•

Visually inspect the friction wheel rubber for
excessive wear, cracks, or loose fit on the friction
wheel drive hub.

•

Also engage the traction control and check if the
friction wheel is making contact with the friction
plate.
If it does not make contact, adjust the traction drive
cable following instructions and recheck the friction
wheel.

Gear Shaft
Lubricate the gear shaft with 6-in-1 grease (part
number 737-0170) at least once a season, or after
every 25 hours of operation. Refer to Figure 10.

•

IMPORTANT: Be careful not to allow grease to get on the
drive plate or rubber friction wheel.

•

Traction Control/ Auger ControlLock
The cams on the ends of the control rods which

CheckV-Belts

interlock the traction drive and auger drive clutches
must be lubricated at least once a season or every 25
hours of operation using a multi-purpose automotive
grease. The cams can be accessed beneath the handle
panel. See Figure 15.

Replace friction wheel rubber if necessary. Refer to
instructions in Service Section.

Follow the instructionsbelow to check the condition of
the drive belts every 50 hours of operation.
•
•
•

Remove the plastic belt cover on the front of the
engine by removing the three self-tapping screws.
Visually inspect for frayed, cracked, or excessively
worn out belts.
Replace belts as necessary as outlined in SERVICING
YOURSNOWTHROWER.

SECTION7: SERVICING
YOURSNOWTHROWER
•

WARNING:

Before servicing, repairing, or
inspecting, disengage all clutch levers and
stop engine. Wait until all moving parts have
come to a complete stop. Disconnect spark
plug wire and ground it against the engine to
prevent unintended starting.

•

Augers

•

The augers are secured to the spiral shaft with two
shear bolts and hex lock nuts. If you hit a foreign object
or ice jam, the snow thrower is designed so that the
bolts may shear. See Figure 16.

•

Reassemble new skid shoes with the hardware
removed earlier (cupped side of bell washer against
the skid shoes). Make certain the skid shoes are
adjusted to be level. Refer to Figure 12.
To remove the shave plate, remove the carriage
bolts, bell washers and hex nuts which secure the
shave plate to the snow thrower housing. See
Figure 16.
Reassemble the new shave plate, making sure
heads of carriage bolts are to the inside of the
housing.
Reinstall the skid shoes and tighten securely.

ReplacingBelts

If the augers do not turn, check if the bolts have
sheared. Two replacement shear bolts and hex lock
nuts have been provided with the snow thrower. Refer
to LoosePartson page 5.

To remove and replace either the auger belt or the drive
belt, follow the steps below and then proceed to the
specific steps listed under respective sub-headings.

IMPORTANT: NEVER replace the auger shear bolts with
standard hex bolts. Any damage to the auger gearbox
or other components, as a result of doing so, will NOT
be covered by your snow thrower's warranty.

•

Disconnect the chute crank assembly at the
discharge chute end by removing the hairpin clip
and the two flat washers.

•

Remove the plastic belt cover, located near the
engine, by removing the three self-tapping screws
and flat washers that secure it. See Figure 17.
Remove the large shoulder bolt and washer on the
left hand side of the engine pulley. See Figure 18.

ShavePlateandSkidShoes
•

The shave plate and skid shoes on the bottom of the
snow thrower are subject to wear. They should be
checked periodically and replaced when necessary.

Hairpin

NOTE: The skid shoes on this machine have two wear

Flat
Washers

Belt Cover Bolts(3)

Belt Cover

edges. When one side wears out, they can be rotated
180 ° to use the other edge.
Shear Bolts

b,.

Shoulder Bolt
(do not remove)

Bolt
Shave Plate

Figure 17

Nut

Figure 16
Remove the six carriage bolts (three per side), bell
washers and hex nuts which attach skidskid shoes
tothe snow throweron eitherside. See Figure 12.

Upper Bolt
(remove)

Brake Bracket Assembly

Auger Belt

Engine Pulley

Shoulder Bolt

Figure 18
Belt Keepers

Auger Belt
•

•

Remove the cotter pin and washer from the ferrule
in order to disconnect the auger idler rod from the
brake bracket assembly. See Figure 19.
Slip the auger control belt (the front belt) off the

Figure 20
•

Reassemble the belt cover and chute directional
control.
Proper Adjustment: With the auger clutch lever in the
disengaged position the top surface of the new belt
should be even with the outside diameter of the pulley.

engine pulley.
Engine-._._
Pulley _
Auger Idler
Rod_

_Auger

FerruleF
Brake Bracket_
Assembly

Control

•

\
_

Bell Washer

Belt

" L/II

To adjust, disconnect ferrule from brake bracket
assembly and thread ferrule in (towards idler)to
increase tension on belt, and out to decrease tension.

NOTE: The brake puck must always be firmly seated in
the pulley groove when the auger control is in the
disengaged position.

_Cob,eBo,,er

Drive Belt
•

Z FittingF

•
Figure 19

•
•

Pull the brake bracket assembly towards the cable
guide roller and unhook the auger cable "Z" fitting.
Remove the upper bolts and lock washers which
attach the auger housing assembly to the frame
assembly using a 9/16" wrench. See Figure 18.
Separate the auger housing from the frame
assembly by tilting the housing forward and pulling
up the handles.
Using a 1/2" wrench, remove the hex screw and
belt washer from the center of the pulley on the
auger housing. Lift the brake bracket assembly out
of the pulley groove and remove the pulley. Be
careful not to lose the key. See Figure 20.
Remove and replace auger belt inside belt keepers.
Reassemble pulley to auger housing with hex
screw and bell washer (cupped side toward the
pulley). Make sure key is in place on shaft and
brake puck is seated in the pulley groove.

Unhook the extension spring from the belt cover
plate. See Figure 21.
Remove drive belt from the engine pulley and
bottom drive pulley. Refer to Figure 21.
Replace belt and reassemble in reverse order.
Reassemble the two halves of the unit hooking the
lower portion of the auger housing over the
stationary shoulder bolts in the frame assembly.

Belt Cover

Belt

Figure 21

•
•
•
•

•

Secure the two halves with the two bolts and lock
washers removed earlier. Refer to Figure 18.
Attach the "Z" fitting of the cable into the brake
bracket assembly. Refer to Figure 19.
Slip the auger control belt over engine pulley.
Insert ferrule on auger idler rod into bracket
assembly and secure with flat washer and cotter
pin. Reassemble the large shoulder bolt and lock
washer as shown in Figure 18.
Reassemble belt cover and chute crank.

Shift Arm Assembly

ChangingFrictionWheelRubber
The rubber on the friction wheel is subject to wear and
should be checked after the first 25 hours of operation,
and periodically thereafter. Replace the friction wheel
rubber if any signs of wear or cracking are found.
•
•
•
•
•

•

•
•

•

•
•

Drain the gasoline from the snow thrower, or place
a piece of plastic under the gas cap.
Tip the snow thrower up and forward, so that it rests
on the housing.
Remove six screws from the frame cover
underneath the snow thrower.
Remove the left wheel from the axle.
Using a 7/8" wrench, hold the hex shaft and remove
the hex bolts and bell washer and bearing from left
side of the frame. See Figure 22.
Holding the friction wheel assembly, slide the hex
shaft out of the left side of the unit. The spacer on
the right side of the hex shaft will fall and the
sprocket should remain hanging lose in the chain.
Lift the friction wheel assembly out between the
axle shaft and the drive shaft assemblies.
Remove the four screws which secures the friction
wheel rubber between the friction wheel plates.
See Figure 22. Discard the old friction wheel
rubber.
Reassemble the new friction wheel rubber to the

Plates

Bearing
Screws
Hub

Friction Wheel Rubber

Figure 22

Hex Shaft

friction wheel assembly, tightening the four screws
in rotation and with equal force.
Insert the pin from the shift arm assembly into the
friction wheel assembly and hold assembly in
position. See Figure 22.
Slide the hex shaft through the left side of the
housing and through the friction wheel assembly.
Insert the hex shaft through the sprocket and the
spacer. Make certain that the chain engages both
the large and the small sprocket.

Hex Hub
Spacer

Of Sprocket

/'/7

NOTE: If the sprocket fell from the snow thrower while
removing the hex shaft, place the sprocket on the hex
shaft. Position the hex hub of the sprocket toward the
friction wheel when sliding the sprocket on to the hex
shaft. See Figure 23.

•

NOTE: If you placed plastic film under the gas cap, be
certain to remove it.

Figure 23
Secure the frame cover with six self-tapping
screws. Put the snow thrower down to its normal
operating position.

Secure with the bell washer and hex bolt removed
earlier.

0ff-seasonStorage
WARNING:

•

NOTE: When storing any type of power equipment in
an unventilated or metal storage shed, care should be
taken to rust proof the equipment. Using a light oil or
silicone, coat the equipment, especially any chains,
springs, bearings and cables.

Never store engine with fuel in

tank indoors or in poorly ventilated areas,
where fuel fumes may reach an open flame,
spark or pilot light as on a furnace, water
heater, clothes dryer or other gas appliance.
•
•
•

Always store the snow thrower in a clean, dry area.

Engine

If unit is to be stored over 30 days, prepare engine
for storage as instructed in the engine manual.
Remove all debris from the exterior of equipment.
Follow lubrication recommendations on page 12.

Refer to separate engine manual for all engine
maintenance procedures.

SECTION8: TROUBLESHOOTING
Problem

Cause

Remedy

Engine fails to start.

1.
2.
3.
4.
5.
6.
7.

Fuel tank empty, or stale fuel.
Blocked fuelline.
Choke net in ON position
Faulty sparkplug.
Safety key not in ignition switch on engine.
Spark plug wire disconnected.
Primer button net being used properly.

1.
2.
3.
4.
5.
6.
7.

Fill tank with fresh gasoline.
Clean the fuel line.
Move switch to ON position
Clean, adjust gap or replace.
Insert the key fully into the switch.
Connect spark plug wire.
Refer to the engine manual

Engine runs erratic.

1.
2.

Unit running on CHOKE.
Blocked fuel line or stale fuel

1.
2.

Water or dirt in fuel system.

Carburetor out of adjustment.

Move choke lever to OFF position.
Clean fuel line and fill tank with clean, fresh
gasoline.
Drain fuel tank and carburetor. Refill with
fresh fuel.
Refer to the engine manual

1.
2.

Spark plug wire loose.
Gas cap vent hole plugged.

1.
2.

Loss of power.

Connect and tighten spark plug wire.
Remove ice and snow from gas cap. Be
certain vent hole is clear.
Refer to the engine manual

Exhaust port plugged.

Engine overheats.

Carburetor not adjusted properly.

Refer to the engine manual or have the
carburetor adjusted by an authorized
engine service dealer.

Excessive vibration.

Loose parts or damaged auger.

Stop engine immediately and disconnect
spark plug wire. Tighten all bolts and nuts. If
vibration continues, have unit serviced by
an authorized service dealer.

Unit fails
to propel itself.

Traction control cable in need of adjustment.

Drive belt loose or damaged.

Adjust traction control cable. Refer to
Adjustments.
Replace drive belt.

Discharge chute clogged.

Foreign object Iodgedin auger.

3.
4.
5.

Auger control cable in need of adjustment.
Auger belt loose or damaged.
Shear bolt(s) sheared.

Unit fails
to discharge snow.

4.
5.

Stop engine immediately and disconnect
spark plug wire. Clean discharge chute and
inside of auger housing.
Stop engine immediately and disconnect
spark plug wire. Remove object from auger.
Refer to Auger Control Test on Page 9.
Refer to Adjustments.
Replace shear bolt(s).

NOTE: For repairs beyond the minor adjustments listed above, contact an authorized Troy-Bilt service dealer.

SECTION9: MODEL10530PARTSLIST
59
47
57

21_
31

8
26

22
\

Model10530

Ref.
No.
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
13.
14.
15.
16.
17.
18.
19.
20.
21.
22.
23.
24.
25.
26.
27.
28.
30.
31.

Part No.
05244A
618-0281A
684-0090A
710-0371
710-0451
710-0459A
710-0528
710-0604A
710-0891
711-0640
711-0677
712-0116
712-0429
712-3010
714-0104
714-0126
714-0135
715-0118
731 -1696
732-0858
736-0119
736-0159
736-0169
736-0174
736-0242
736-0250
736-0271
736-3008
738-0281
741-04024

Ref.
No.

Part Description

Part No.

Bearing Housing
Bracket Assembly: Auger Break
lmpellerAssembly:
16"
Hex Lock Bolt 5/16-18 x .875"

32.
33.
34.
35.

741-0192
741-0475
741-0494
747-0980

Carriage Bolt 5/16-18 x .750"
Hex Screw, Special 3/8-24 x 1.5"
Hex Screw 5/16-18 x 1.25"

36.
37.
38.

754-0222A
756-0178
756-0243

Self-Tapp. Screw 5/16-18 x .625"
Shear Bolt 5/16-18 x 1.75"
Stud

39.
40.
41.

784-0385A
784-5076
784-5123

Ferrule
Jam Nut 3/8-24
Hex Lock Nut 5/16-18
Hex Nut 5/16-18

42.
43.
44.
45.

784-5710
784-5711
618-0436
705-5206A

Hairpin Clip
Key
Key
Spiral Pin
Chute Adapter
Extension Spring
LockWasher
5/16Washer
Lock Washer
Wave Washer
Beleville Washer
Flat Washer

46.
47.
48.
49.
50.
51.
52.
53.
54.
55.
56.
57.

705-5207A
684-04006
784-5697
737-3000
738-0491
736-0105
784-0315
784-5715A
710-0389
710-3168
712-0798
710-1260A

Spring Washer
Flat Washer
Shoulder Screw

58.
59.
60.

712-0717
731-2643
731-2635

Self-Aligning

Bearing

Part Description
Flange Bearing w/Flats
Plastic Bushing
Flange Bushing
Idler Rod: Auger
V-Belt
Flat Idler
Pulley
Idler Bracket: Auger
Support Bracket
Chute Crank Bracket
Support Plate
Chute Bracket
Gear Assembly
Spiral Assembly RH
Spiral Assembly LH
Auger Housing Assembly
Slide Shoe
Lube Fitting
Spiral Axle
Bell Washer
Bearing Housing
Shave Plate
Carriage Screw
Carriage Bolt
Hex Nut 3/8-16
Screw, 5/16-18 x .75
Insert Nut, 3/8-16
Chute Clean-out Tool
Mount, Chute Clean-out Tool

Model10530

1
50

/
22

77
/

19
72

7
44

28.
31

Model10530

Ref.
NO.
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
13.
14.
15.
16.
17.
18.
19.
20.
21.
22.
23.
24.
25.
26.
27.
28.
29.
30.
31.
32.
33.
34.
35.
36.
37.
38.
39.
40.
41.
42.
43.
44.
45.

Part No.
05523
750-1302A
618-0279
618-0280
618-0282B
618-0296A
684-0162
684-0161
684-0117
684-0118
684-0119
684-0120
684-0122
710-0195
710-0538
710-0599
710-0788
710-1652
710-3001
710-3008
710-3103
710-3180
711-1191
711-1193
711-1194
712-0116
712-0138
712-0221
712-0429
712-0798
712-3010
713-0284
713-0286
713-0413
714-0101
714-0104
714-0115
714-0388
715-0249
717-0302
732-0121
732-0209
736-0119
736-0158
736-0160

Ref.
No.

Part Description

Part No.

Pivot Support Bracket
Spacer, .6725 x 1.125 x 2.485
Dogg Assembly LH
Dogg Assembly RH
Shaft Assembly
Friction Wheel Assembly
Support Bracket Assembly
Shift Arm Assembly
Shift Rod Assembly
Auger Actuator Bracket Assy.
Drive Actuator Bracket Assy.
Frame Assembly
Sprocket Assembly
Hex Screw, 1/4-28 x .625"

46.
47.
48.
49.
50.
51.
52.
53.
54.
55.
56.
57.
58.
59.

736-0163
736-0217
736-0242
710-0604A
736-0300
736-0329
736-0623
712-0717
784-0404
784-0407
738-0143
738-0279
738-0924
741-0163A

Hex Screw, 5/16-18
Self-tapping Screw,
Self-tapping Screw,
Self-tapping Screw,
Hex Screw 3/8-16 x

60.
61.
62.
63.
64.

714-0151A
741-0563
741-0747
746-0949A
746-0951

Hex Screw 5/16-18 x .75"
Hex Screw 5/16-18 x 2"
Hex Screw 5/16-18 x 1.75"

65.
66.
67.

747-0973
750-0903
750-0997

Hex Shaft: Drive
Actuator Shaft
Actuator Drive Shaft

68.
69.
70.

741-0748
737-3000
756-0344

Lock Nut
Hex Nut 1/4-28
Jam Lock Nut
Hex Lock Nut
Hex Nut 3/8-16
Hex Nut 5/16-18
Chain
Chain

71.
72.
73.
74.
75.
76.
77.
78.

756-0625
784-0406
784-0379
784-0380
784-0384
784-0403
738-0975
784-5617A

Sprocket
Hairpin Clip
Hairpin Clip
Cotter Pin

79.
80.
81.
82.

735-0243B
718-0301A
618-0063A
634-0225-662

Key
Roll Pin
Drive Plate

----

734-2031
734-1124
734-0255

Extension Spring
Extension Spring
Lock Washer 5/16
Lock Washer 5/8
Flat Washer

83.
----

634-0226-662
734-2031
734-1124
734-0255

x .625"
1/4-20 x .5
1/4-20 x 1"
1/4-20 x .625"
.880"

Part Description
Flat Washer
Lock Washer
Bell Washer
Self-tapping Screw, 5/16-18 x .625
Flat Washer
Lock Washer
Flat Washer
Nut Insert, 3/8-16
Bearing Retainer Bracket
Axle Bearing Support Bracket
Shoulder Screw
Spindle: Drive Plate
Shoulder Screw 1/4-28 x .375"
Bearing Housing Assembly
Click Pin
Ball Bearing
Ball Bearing
Steer Cable
Auger Idler Cable
Drive Clutch Rod
Split Spacer
Spacer
Flange Bearing
Lube Fitting, 3/16
Drive Pulley
Roller Cable
Frame Support Bracket
Frame Cover: Upper
Frame Cover: Lower
Auger Cable Bracket
Shift Bracket
Axle: Wheel
Friction Plate
Friction Wheel Rubber
Friction Wheel Hub
Friction Wheel Bearing
Wheel Assembly, LH
X-Trac Tire Only
Rim Only
Air Valve Only
Wheel Assembly, RH
X-Trac Tire Only
Rim Only
Air Valve Only

Model10530
39
43

36
37
35

@.
22

29
24

\
16

25
9

Model10530
Ref.
No.
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
13.
14.
15.
16.
17.
18.
19.
20.
21.
22.
23.
24.
25.
26.
27.
28.
29.
30.
31.
32.
33.
34.
35.
36.
37.
38.
39.
40.
41.
42.
43.
44.

Part No.
646-0012
684-0053B
705-5266
710-1879
710-1878
710-0458
710-0572
747-1136
710-3015
711-0677
712-0287
629-04010
712-3010
714-0101
714-0104
720-0201A
720-0284
726-0100
736-0105
736-0185
736-0242
736-0270
736-0275
741-0475
747-0624
747-0983
747-0997
749-0989A
749-0990A
749-0991
750-0963
710-1625
712-0127
725-0157
746-0950
725-1658
705-5218
705-5219
710-1003
712-0271
712-0429
720-0232
731-04069
725-1672

Part Description
Cable Assembly: Auger/Drive
Chute Crank Assembly, Lower
Chute Crank Bracket
Hex Screw, 3/8-16 x .88"
Hex Screw, 3/8-16 x 1.75"
Carriage Bolt 5/16-18 x 1.75"
Carriage Bolt 5/16-18 x 2.5"
Lamp Retainer
Hex Screw 1/4-20 x .75"
Ferrule
Hex Nut 1/4-20
Lamp Wire Harness
Hex Nut
Hairpin Clip
Hairpin Clip
Chute Crank Knob
Knob
Push Cap
Bell Washer
Flat Washer
Beleville Washer
Bell Washer
Flat Washer
Plastic Bushing
Chute Crank
Lower Shift Red
Upper
Upper
Upper
Lower
Clutch

Shift Red
Handle LH
Handle RH
Handle
Rod Connector

Oval C-Sunk Screw
Flat Weld Nut
Cable Tie
Trigger Control
Halogen Lamp
Handle Engagement RH
Handle Engagement LH
Special B Screw
Hex Sems Nut
Hex Lock Nut
Shift Knob
Handle Panel
Lens Assembly

Model10530

" •

29
<'"

Ref.
NO.
1.
2.

Part No.

Description

07386
684-0123A
710-0191
710-0237

Washer
Belt Cover Bracket Assembly
Hex Screw 3/8-24 x 1.25"
Hex Screw 5/16-24 x .625"

710-1008
710-0607
710-0672
712-0116

Self-tapping Sems Screw
TT Screw 5/16-18 x 0.5"
Hex Lock Screw 5/16-24 x 1.25"
Jam Nut

9.
10.

714-0118
731-2531

Key
Belt Cover

11.
12.
13.
14.
15.

732-0303
736-0159
736-0217
736-0242
736-0264

Extension Spring
5/16 Washer
Lock Washer
Beleville Washer
Flat Washer

3.
4.
5.
6.
7.
8.

Ref.
No.
,

Part No.

Description

738-0982

Shoulder Screw

748-0234
784-0131

Shoulder Spacer
V-Belt

21.

756-0240
756-0241B

22.
23.
24.

784-5726
750-1148A
748-0418

Flat Idler
Double Pulley
Idler Bracket
Spacer

25.
26.
27.
28.
29.
30.

717-0882A
629-0071
684-04011
684-04014
710-04082
712-3004A

17.
18.
19.
20.

Spacer, .33 x 1.0 x .36
Spacer
Extension Cord: 110V, 3-prong
Spark Plug Cap
Engine Shroud (Incl. Ref. 27)
Screw, #10-16 x .75
Flange Lock Nut, 5/16-18

Model10530
Ref.
No.

Part No.

Description

710-0276

Carriage Screw

710-0458

Carriage Bolt 5/16-18 x 1.75"

710-0805

Hex Bolt 5/16-18 x 1.5"

710-0896

Hex AB Screw 1/4-14 x .625"

710-3015

Hex Screw 1/4-20 x .75"

712-0429

Hex Lock Nut

712-3027

Hex Flange Lock Nut

731-0846C

Upper Chute

731-0851A

10.

731-1313C

Chute Flange Keeper
Cable Guide: Chute Tilt

11.

731-0903D

Lower Chute

12.

784-5680

Handle Suppt. Bracket 5/8 RH

13.

736-0159

5/16 Washer

14.

736-0231

Flat Washer

15.

736-0506

Special Washer

16.

746-0902

Chute Control Cable

17.

746-0903

Chute Cable w/Clip

18.

784-5594

Cable Bracket

19.

784-5604

Chute Tilt Handle

20.

684-0102

Handle Panel Assembly w/Tilt

21.

710-0459A

Hex Bolt 3/8-24 x 1.5"

22.

710-0599

TT Screw 1/4-20 x 0.5"

23.

711-0653

Clevis Pin

24.

712-0116

Jam Nut

25.

784-5682

26.

714-0104

Handle Suppt. Bracket 3/8 RH
Cotter Pin

27.

732-0145

Spring

28.

732-0193

Spring

29.

732-0746

Torsion Spring

30.

735-0199A

Rubber Bumper

31.

736-0105

Bell Washer

32.

784-5681

Handle Suppt. Bracket 3/8 LH

33.

736-0509

Special Washer

34.

747-0877

Cam Red

35.

748-0362

Cam: Handle Lock

36.

748-0363

Pawl: Handle Lock

37.

784-5619A

Shift Handle

38.

784-5679

Handle Suppt. Bracket 5/8 LH

Model10530

®
14

R_.
No.

NOTE:

Part No.

Description

618-0246

Housing Assembly, RH

618-0435

Housing Assembly, LH

710-1260A

Screw, 5/16-18 x 0.75

711-0908A

Axle, Auger

711-1133

Shaft, Auger Drive

714-0126

Key, Hi Pro, 3/16 x 3/4

714-0135

#91 Woodruff Key 1/4 x 3/4

716-0111

Snap Ring .875 Dia.

717-0299

Gear, Worm, Double Thread LH

10.

717-1425

Gear, Worm, LH

11.

721-0145

Seal, Oil .875 ID

12.

721-0325

Plug, 1/4x .437

13.

736-0266

Washer, Flat, 1.52 x 2.0

14.

736-0291

Washer, Flat, .88 x 1.38

15.

737-3000

Lube Fitting, 3/16 Drive

16.

738-0275

Shaft, Worm Gear

17.

741-0184

Bearing, Thrust .877

18.

741-0217

Sleeve Bearing, .877 x .125 x 1.11

19.

618-0436

Auger Gearbox Assembly Complete

When rebuilding a gearbox assembly, include 3 oz. of Shell Alvania EP Lead-Free Grease (Part No. 737-0168).
26

777D06575

777D06574

J
777122052

777S32066

777122049

777122051

777S32065

777D06576

777D06577

777122047

Tecumseh Engine Labels
751T642082100

751T64141769

751T641393

m
Topof plasticenginecover
abovemufflerventsin plastic

On plasticenginecover
eft sideofele=ric starter

On plasticenginecover
aboveprimerknob

o
o.
i

O
O

MANUFACTURER'S

LIMITED WARRANTY

FOR:

O TRO_
_ B_ILT'_
The limited warranty set fodh below is given by Troy-Bilt LLC
with respect to new merchandise purchased and used in the
United States, its possessions and territories.
Troy-Bilt LLC warrants this product against defects for a
period of two (2) years commencing on the date of original
purchase and will, at its option, repair or replace, free of
charge, any part found to be defective in materials or
workmanship. This limited warranty shall only apply if this
product has been operated and maintained in accordance
with the Operator's Manual furnished with the product, and
has net been subject to misuse, abuse, commercial use,
neglect, accident, improper maintenance, alteration,
vandalism, theft, fire, water, or damage because of other peril
or natural disaster. Damage resulting from the installation or
use of any accessory or attachment not approved by Trey-Bilt
LLC for use with the product(s) covered by this manual will
void your warranty as to any resulting damage.
Normal wear parts or components thereof are subject to
separate terms as follows: All normal wear parts or
component failures will be covered on the product for a period
of 90 days regardless of cause. After 90 days, but within the
two year period, normal wear part failures will be covered
ONLY IF caused by defects in materials or workmanship of
OTHER component parts. Normal wear parts and
components include, but are net limited to: batteries, belts,
blades, blade adapters, grass bags, rider deck wheels, seats,
snow thrower skid shoes, shave plates, auger spiral rubber,
and tires.
HOW TO OBTAIN SERVICE: Warranty service is available,
WiTH PROOF OF PURCHASE, through your local authorized
service dealer. To locate the dealer in your area, check your
Yellow Pages, or contact Troy-Bilt LLC at P.O. Box 361131,
Cleveland, Ohio 44136-0019, or call 1-866-840-6483 or 1330-558-7220, or log on to our Web site at www.troybilt.cem.
This limited warranty does net provide coverage in the
following cases:
a.

b.
c.

The engine or component parts thereof. These items
carry a separate manufacturer's warranty. Refer to
applicable manufacturer's warranty for terms and
conditions.
Log splitter pumps, valves, and cylinders have a separate one year warranty.
Routine maintenance items such as lubricants, filters,
blade sharpening, tune-ups, brake adjustments, clutch
adjustments, deck adjustments, and normal
deterioration of the exterior finish due to use or
exposure.

e.
f.

Troy-Bilt LLC does net extend any warranty for
products sold or exported outside of the United States,
its possessions and territories, except those sold
through Troy-Bilt LLC's authorized channels of export
distribution.
Parts that are net genuine Troy-Bilt parts are net
covered by this warranty.
Service completed by someone other than an
authorized service dealer is net covered by this
warranty.
Transportation charges and service calls are not
covered.

No implied warranty, including any implied warranty of
merchantability of fitness for a particular purpose,
applies after the applicable period of express written
warranty above as to the parts as identified. No other
express warranty, whether written or oral, except as
mentioned above, given by any person or entity,
including a dealer or retailer, with respect to any product,
shall bind Troy-Bilt LLC. During the period of the
warranty, the exclusive remedy is repair or replacement
of the product as set forth above.
The provisions as set forth in this warranty provide the
sole and exclusive remedy arising from the sale. Troy-Bilt
LLC shall not be liable for incidental or consequential
loss or damage including, without limitation, expenses
incurred for substitute or replacement lawn care services
or for rental expenses to temporarily replace a warranted
product.
Some states do not allow the exclusion or limitation of
incidental or consequential damages, or limitations on how
long an implied warranty lasts, so the above exclusions or
limitations may not apply to you.
In no event shall recovery of any kind be greater than the
amount of the purchase price of the product sold. Alteration
of safety features of the product shall void this warranty.
You assume the risk and liability for loss, damage, or injury to
you and your property aed/or to others and their property
arising out of the misuse or inability to use the product.
This limited warranty shall not extend to anyone other than the
original purchaser or to the person for whom it was purchased
as a gift.
HOW STATE LAW RELATES TO THIS WARRANTY:

This

limited warranty gives you specific legal rights, and you may
also have other rights which vary from state to state.

Troy-Bilt LLC, P.O.BOX361131CLEVELAND,OHIO44136-0019; Phone:1-866-840-6483,1-330-558-7220

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.2
Linearized                      : No
Page Count                      : 28
Page Layout                     : SinglePage
Page Mode                       : UseNone
Producer                        : Goby Monitor Application version 3, 2, 1, 4
Create Date                     : Wed Apr 04 19:29:41 2007
Author                          : 
Title                           : 
Subject                         :

EXIF Metadata provided by EXIF.tools

Troybilt 31AH9V75063 User Manual SNOW THROWER Manuals And Guides L0401087

TROYBILT Snowthrower, Gas Manual L0401087 TROYBILT Snowthrower, Gas Owner's Manual, TROYBILT Snowthrower, Gas installation guides

Navigation menu

Versions of this User Manual:

Views

Navigation