Tung Keng Enterprise LK001 Console for Sporting Goods User Manual

Tung Keng Enterprise Co. Ltd Console for Sporting Goods

User Manual

25 LK500Ui / Ri / Ei CONSOLE OPERATIONSSPECIFICATIONS:ENTER RESET To reset all parameters to default valueSTART/STOP To start or stop trainingUP To make upward setting changeDOWN To make downward setting changeRECOVERY In stop or start mode, pressing this button will start Heart Rate recovery status measurement. Time will count down from 60 secondsQUICK START Starts the machine without any preset program or data from userFUNCTION:TIME Displaying the workout time while exercisingSPEED Displaying the current speedDISTANCE Accumulating the distance while exercisingPULSE 30-240 BPMCALORIES Counts calories while exercisingRPM Displaying crank speed in revolution per minute
26 POWER MODEWhen the machine powers on, the display will light up with all numerals. After two seconds, it will enter the "user selecting" mode. If the user does not operate the machine, or the machine receives no signal after 4 minutes, the computer will enter an idol mode. GETTING STARTED - OPERATING PROCEDURE:Start pedaling and the console will turn on. Use the UP/DOWN buttons to set up your user data by selecting any user U0-U4. Press the ENTER button to accept user selection. Press UP/DOWN buttons to toggle between genders. Press ENTER to accept. Use the UP/DOWN to set AGE then press ENTER. Use the UP/DOWN buttons to enter height in inches then presss ENTER to accept. Use the UP/DOWN buttons to input weight then press ENTER to select. See below for step by step instructions. 1. Press ENTER to conrm the USER, then enter the sex setting. e right side will displays SEX, use the UP/DOWN buttons to choose male or female. 2. Press ENTER to conrm the gender selection, then enter the AGE setting. e right side will display AGE, use the UP/DOWN buttons to select age setting.
27 3. Press ENTER to conrm the AGE setting, then enter the HEIGHT setting. e right side will display HEIGHT, use the UP/DOWN buttons to select the HEIGHT setting.4. Press ENTER to conrm the WEIGHT setting, then enter WEIGHT setting. e right side will display WEIGHT, use the UP/DOWN buttons to select the WEIGHT value. 5. Press ENTER to conrm the HEIGHT setting, then enter the exercise program selecting page. Use the UP/DOWN buttons to select between the exercise programs below.MANUAL PROGRAM FITNESSWATT PERSONAL HRCRANDOM
28 NAVIGATING THE PROGRAMSMANUAL MODEUser may preset their own resistance level from 1 to 24 by pressing the UP/DOWN buttons. e default resistance level is 1. Press ENTER to conrm. Using the UP/DOWN buttons enter values for TIME, DISTANCE, CALORIES, PULSE, and then press START to begin your workout.PROGRAM MODEere are 12 preset programs. Use the UP/DOWN buttons to select the desired program prole, then press the ENTER button to conrm. Use the UP/DOWN buttons to adjust the resistance level. Press ENTER to conrm. Enter values for TIME, DISTANCE, CALORIES, PULSE, and then press START/STOP to begin your workout.FITNESS TESTUse the UP/DOWN buttons to select FITNESS and press ENTER. Press START/STOP to start the test. e user has to achieve the greatest distance possible in 8 minutes. When the time is up, the electronic device will work out the dierence and your tness rating will be displayed up on the screen.PERSONAL MODEUsers may create their own prole in this mode. e rst segment of the prole will start blinking. Use the UP/DOWN buttons to adjust resistance level for each segment. Once all 16 segments have been entered, press the ENTER button to conrm. Press START/STOP to begin your workout.WATT CONTROL MODEEnter values for TIME, DISTANCE, CALORIES, PULSE, and then press START/STOP to begin your workout. User may set the Watt value by pressing the UP/DOWN buttons to change in 10 Watt increments.HRC MODEInput personal data: SEX, AGE, HEIGHT and WEIGHT. User may select dierent target Heart Rate from 55%, 75%, 90% and TARGET by using the UP/DOWN buttons. Press ENTER to conrm. en, enter values for TIME, DISTANCE, CALORIES, and then press START/STOP to begin your workout.
29 PRESET PROGRAMSP2 P2 P3P4 P5 P6P7 P8 P9P10 P11 P12HRC PROGRAMS (55%, 75%, 90%, TAG)HRC 55% HRC 75% HRC 90% HRC Target Heart Rate
30 TEST FUNCTIONSRECOVERY TESTPress RECOVERY key to test HRC recovery speed. When in test mode, it will detect the HRC within 10 seconds. When nished, if there is no HRC displayed, the program will exit out of the HRC recovery mode. If there is HRC displayed, the workout will enter into 60 seconds HRC recovery. Test result is shown below: VALUE CONDITIONF1 BestF2 Very goodF3 GoodF4 NormalF5 Bad F6 WorseFITNESS TESTEnter FITNESS program and start the test. Test time is 8 minutes. Test result is below:VALUE CONDITIONF1 Very GoodF2 GoodF3 FairF4 PoorF5 Very Poor
31 FUNCTION STATISTICS AND RANGESITEM SCREEN SHOWN RANGE SETTING RANGE PRESET VALUE SAVE1 SEX MALE/ FEM yes2 AGE 10 - 100 yes3 WEIGHT(METRIC) 20 - 330(Lb) 10 - 150 (KG)yes4 HEIGHT 36 - 84(INCH) 90 – 21 0(CM)yes5 TIME 0:00 - 99:59 0:00 - 99:00 0:00 no6 DISTANCE 0.0 - 99.99 0.0 - 99.50 0.0 no7 CALORIES 0 - 999 0 - 990 0 no8 SPEED 0.0 - 99.9 0.0 no9 PULSE 30 - 200 bpm 0 no10 WATT 0 - 999 0 no11 RPM 0 - 250 rpm 0 no12 BRAKE RESISTANCE LEVEL L1 - L24 L1 no “WARNING! Heart rate monitoring systems may be inaccurate. Over exercising may result in serious injury or death. If you feel faint stop exercising immediately.
32 DOWNLOADING APPS AND PAIRING YOUR DEVICE WITH YOUR EQUIPMENTDOWNLOADING THE SOFTWAREConnect the Apple device with the App Store (iTunes) or your Android Device with Google Play, search for "Pafers", then read the APP introductions and Download the APPs with bicycle/elliptical machine functions to your device, for example Pedal Monitor or other applicable apps. Note: if you download an APP for a treadmill and pair it with an Elliptical it will not work. • e App uses bluetooth mode, so please make sure the equipment and the device you are using both have bluetooth function.• e App contains the following functions, the user must open the 3G network or wi- network:(a) Managing Data - After completing the registration in the "Pafers" App, log on to your personal account. Now that you have registered you can record all of your workout data and save it to your device.(b) Some APPs need connection to Google maps in order to function correctly. PAIRING THE BLUETOOTH DEVICE WITH AN APPLE DEVICE1. Place the Apple Device on the area in front of the LCD screen.2. Enter into settings and turn Bluetooth on.3. Your Apple Device will detect all Bluetooth devices within range (following on screen instructions), click on the appropriate bluetooth device name and conrm your connection.4. After paired successfully, please start the APP within 2 minutes, if you do not, Bluetooth will automatically cancel the pairing. Please keep the Apple Device within a range of 2 meters for best quality connection. If you see “not connected,” please perform the above steps again. 5. Press the Apple Device home button, the screen will return to the desktop.6. Start the APP you downloaded. When the APP connects with the equipment successfully, the APP screen buttons will unlocked. Start from APP interface using a variety of modes to control the exercise equipment. Pay attention to the APP instructions and function introduction. If you have need help with the APP, please browse the APPs download page description or contact Pafers for instructions.7. When you are done using the APP, please press the HOME button on the Apple Device twice to close the APP.
33 PAIRING THE BLUETOOTH DEVICE WITH AN ANDROID DEVICE1. Place the Android Device on the area in front of the LCD screen.2. Enter into settings and turn Bluetooth on.3. Your Android Device will detect all Bluetooth devices within range (following on screen instructions), click on the appropriate bluetooth device name and conrm your connection.4. After paired successfully, please start the APP within 2 minutes, if you do not, Bluetooth will automatically cancel the pairing. Please keep the Android Device within a range of 2 meters for best quality connection. If you see “not connected,” please perform the above steps again. 5. Press the Apple Device home button, the screen will return to the desktop.6. Start the APP you downloaded. When the APP connects with the equipment successfully, the APP screen buttons will unlocked. Start from APP interface using a variety of modes to control the exercise equipment. Pay attention to the APP instructions and function introduction. If you have need help with the APP, please browse the APPs download page description or contact Pafers for instructions.7. When you are done using the APP, please press main screen button on the Android Device twice to close the APP.COMPATIBLE DEVICESAndroidBluetooth & App Enabled Android DeviceApple ProductsiPod touch (4th generation) iPod touch (3rd generation)iPhone 5 iPhone 4SiPhone 4 Mini iPadiPad iPad 2i.Concept Bluetooth products are compatible with Apple devices with iOS 5.1 or later. It is recommended to update iOS to latest version to obtain the best user experience.iPad, iPhone, iPod, iPod classic, iPod nano, iPod shue, and iPod touch, is a registered trademark of Apple, Inc., in the United States and other countries.“Made for iPod,” “Made for iPhone,” and “Made for iPad” mean that an electronic accessory has been designed to connect specically to iPod, iPhone, or iPad, respectively, and has been
34 for the operation of this device or its compliance with safety and regulatory standards. trademarks of Apple Inc., registered in the U.S. and other countries.Care has been taken to assure that your equipment has been properly adjusted and lubricated at the factory. It is not recommended that the user attempt service on the internal components. Instead, seek service from an authorized service center. However, you may clean the outer surface. Use a soft cloth, dampened with warm water. Do not use aerosol of harsh chemicals will destroy the protective coating and cause a static build-up that may damage the some of the components.MAINTENANCE AND CLEANINGFCC ID: PHGLK001NOTEThis equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: ◆ Reorient or relocate the receiving antenna. ◆ Increase the separation between the equipment and receiver. ◆ Connect the equipment into an outlet on a circuit different from that to which the receiver is needed. ◆ Consult the dealer or an experienced radio/TV technician for help. Warning: Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user authority to operate the equipment. 1. To comply with FCC RF exposure compliance requirements, a separation distanc of at least 20 cm must be maintained between the antenna of this device and all persons. 2. This Transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.
35 EXPLODED VIEW DRAWING
36 PARTS LISTTo order replacement parts: provide your customer service representative with the product model number and the part number located on the Parts List below, along with the quantity you require.No. Description Qty No. Description Qty No. Description Qty(A) FRAME AND FITTINGS 1 (E) REAR STABILIZER SET 1 I03 Bearing 4A01 Frame assembly 1 E01 Rear stabilizer set assembly 1 I04 Handlebar tube upper assembly L 1A02 Crank assembly 1 E02 Hex screw nut m8xp1.25 2 I05 Handlebar tube upper assembly R 1A03 Idle wheel assembly 1 E03 Adjustment foot pad 4 I06 HDR foam grip φ31x3.0Tx970 2A04 Belt wheel φ310 1 E04 End cap φ75 2 I07 End cap -φ1-1/4” 2A05 Hex screw m8xp1.25X15 4 E05 Rear stabilizer cover 1 I08 Hex screw m8xp1.25X15 2A06 Nut m8xp1.25 4 E06 End cap φ1-1/2”x2.0T 4 I09 Flat washer φ8.5Xφ30x2.0T 2A07 Drive belt 480” 1 E07 CKS hex screw m10xp1.5X40 3 I10 Screw m8xp1.25X45 4A08 Spring A 1 E08 Spring washer m10 3 I11 Nut m8xp1.25 4A09 Bearing 2 E09 Flat washer φ10xφ20x1.5T 3 I12 Wave washer ∮26.4X∮34.2X0.3T 4A10 C-shaped ring φ15 1 E10 Cross screw m4xp0.7X15 2 I13 Washer φ25xφ35x1.0T 2A13 Flywheel φ260 1E11 Wheel compressing board 2A14 Screw nut 3/8”-26 thread 2 E12 Hex screw m8xp1.25X15 4 (J) RELATED POLE SET 1A15 Hex screw nut 3/8”-26 thread x4t 2 E13 Nut m8 4 J01 Pole set assembly R 1A23 Belt 4.8X330mm 7 E14 Foam sticker 600mmx25mmx1.5T 4 J02 Pole set assembly L 1A24 Belt 2.2X80mm 1 E15 Washer φ4xφ10x1.0T 2 J03 Shaft -pos12-r (φ12 right thread) 2A25 Belt 3.6X102mm 1 J04 Nut m12xp1.75 4A27 Sensor xing base 1 (F) FOOT PEDAL AND FITTINGS 1 J05 Foam sticker 90x90x3.0T 2A28 Cross screw m4xp0.7X10 1 F01 Foot pedal iron tube assembly 2 J06 Shaft 2A29 Power supply 1 F02 Bearing 16 J07 CKS hex screw m8xp1.25X15 4A30 Crank shaft bushing 1 F03 Wheel xing bushing 2 J08 Plastic washer 2A31 Small motor (wire puller) 1 F04 Inner and outer shaft tube (short) 8 J09 End cap 4A32 Steel rope 1 F05 Wave washer φ17xφ24x0.3T 2 J10 Washer φ8.5Xφ19x2.0T 4A33 Screw m5xp0.8X12 4 F06 Fixing screw m8xp1.25X135 2 J11 CKS hex screw m12xp1.75X40 2A40 Wire clip xing knob uc-2 3 F07 Nut m8xp1.25 4 J12 CKS hex screw m6xp1.0X10 2A41 Cross screw m4xp0.7X10 3 F08 PU wheel φ74x44 4A42 Hex screw m8xp1.25X25 1 F09 Foot pedal xing plate assembly (front) 2 (K) PLASTIC FITTINGS 1A43 Washer φ8xφ16x1.5T 1 F10 CKS hex screw m8xp1.25X85 2 K01 Frame cover middle 1A44 Washer φ8xφ19x3.0T 1F11 Arc washer 4 K02 Foot pedal iron tube cover L 1A45 Nut m8xp1.25 1 F12 Foot pedal iron tube plastic iron core 2 K03 Foot pedal iron tube cover R 1A51 Steel rope xing plate 1 F13 Wheel cover L 2 K04 Handlebar tube cover front L 1A52 Screw m5xp0.8X10 1 F14 Wheel cover R 2 K05 Handlebar tube cover rear L 1F15 Cross screw m4xp0.7X15 4 K06 Handlebar tube cover front R 1(B) FRONT BASE TUBE SET 1 F16 Hex screw m8xp1.25X15 2 K07 Handlebar tube cover rear R 1B01 Front base tube assembly 1 F17 Washer φ8xφ25x2.0T 2 K08 Connecting pole cover L 2B02 End cap ø75 2 F18 Wave washer φ17xφ24x0.3T 2 K09 Connecting pole cover R 2B03 Hex screw nut 2 K10 Foot pedal 2B04 Hex screw m8xp1.25X45 2 (G) CONTROL TUBE SET 1K11 Control tube plastic 1B05 Nut m8xp1.25 2 G01 Control tube assembly 1 K12 Self-tapping screw φ5x15 8B06 Washer φ8xφ16x2.0T 2 G02 CKS hex screw m10xp1.5X70 2 K13 Screw m4xp0.7X15 6B07 Bearing wheel φ70xφ8x28t 2 G03 CKS hex screw m8xp1.25X15 1 K14 Screw m5xp0.8X10 8G04 Nut m10xp1.25 2 K15 Washer φ6xφ13x1.0T 8(C) OUTER COVER SET 1 G05 Washer φ8xφ25x2.0T 1 K16 Screw m5xp0.8X10 1C01 Frame side cover L 1 G06 Guide thread l=300 2C02 Frame side cover R 1 G07 Computer xing plate D 1 (L) COMPUTER CONSOLE AND WIRES 1C03 Plastic locked xing iron plate 2 G08 Screw m5xp0.8X12 4 L01 Console 1C04 Plastic locked xing iron plate-short 1 L02 Screw m4xp0.7X10 4C05 Washer φ6xφ16x1.0T 2 (H) HAND GRIP PULSE SET 1 L06 Lower control wire 1C06 Screw m5xp0.8X10 10 H01 Hand grip pulse plastic base 4 L09 Speed sensor wire 1C07 Screw m5xp0.8X12 2 H02 Hand grip pulse sensor plate 4 L10 Power supplier wire 1C08 Self-tapping screw φ5x12 4 H03 Double side tape 25mmx75mmx0.3T 4H04 Screw m3xp0.5X30 4 (M) OTHER 1(D) TURNPLATE SHELF AND FITTINGS 1 H05 Hex screw nut m3xp0.5 4 M01 Parts bag 1D01 Turnplate cross shelf assembly 2 H06 End cap -φ1-1/4” 2 M02 Waterbottle holder 1D02 Plastic turnplate 2 M03 Waterbottle holder bracket 1D03 Self-tapping screw φ5x15 16 (I) HANDLE BAR SET 1 M04 Screw m6xp1.0X15 2D04 Screw nut (washer) m14xp1.5X10t 2 I01 Handlebar tube assembly L 1 M05 Washer ψ6xψ13x1.0T 2D05 Turnplate cover 2 I02 Handlebar tube assembly R 1 M08 Guide thread l-300 black 4φ=Diameter
37 LIMITED LIGHT COMMERCIAL WARRANTYBH North America will repair or replace, free of charge, at its option, parts that are defective as a result of material or workmanship. Seven (7) year replacement warranty coverage on frame and ve (5) years on other parts. Labor warranty coverage is one (1) year. Warranty covers the original consumer purchaser only.LIMITED RESIDENTIAL WARRANTYBH North America will repair or replace, free of charge, at its option, parts that are defective as a result of material or workmanship. Lifetime replacement warranty coverage on frame and ten (10) years on other parts. Labor warranty coverage is two (2) years. Warranty covers the original consumer purchaser only.THIS WARRANTY DOES NOT COVER• Pre-delivery set-up.• Components that require replacement due to dirt or lack of regular maintenance.• Expendable items which become worn during normal use.• Repairs necessary because of operator abuse or negligence or the failure to operate and maintain the equipment according to the instructions contained in the Owner’s Manual.WARRANTYBH North America Corporation20155 EllipseFoothill Ranch, CA 92610Phone: 949.206.0330; Toll Free: 866.325.2339; Fax: 949.206.0013Web: www.BHFitnessUSA.comMon - Fri 8am - 5pm PSTFOR WARRANTY REPAIRS, PLEASE DO NOT TAKE YOUR MACHINE BACK TO THE RETAIL STORE. CONTACT BH FITNESS FIRST.For more detailed warranty information or to register your product warranty easily online, visit our website at: www.BHFitnessUSA.com

Navigation menu