Turning Technologies RCLC01 ResponseCard Single Event User Manual RCSE 01 Keypad User Guide v1 1

Download:
Mirror Download [FCC.gov]
Document ID	2016515
Application ID	cLa0oqsO2VxHvepDVqGL1A==
Document Description	Exhibit D Users Manual per 2 1033 b3
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	3.98kB (49713 bits)
Date Submitted	2013-07-15 00:00:00
Date Available	2013-07-15 00:00:00
Creation Date	2013-07-15 10:37:10
Producing Software	Acrobat Distiller 11.0 (Windows)
Document Lastmod	2013-07-15 10:37:10
Document Title	Microsoft Word - RCSE-01 Keypad User Guide v1.1
Document Creator	PScript5.dll Version 5.2.2
Document Author:	decrowder

RCSE-01 Keypad User’s Guide
v1.1
07/02/2013
Revision
1.0
1.1
Date
06/6/2013
7/2/2013
Comments
Initial
Updated FCC and IC Statement
Overview:
The ResponseCard Single Event Keypad (RCSE-01) is designed to be used with the Turning
Technologies RF Receivers connected to a PC. The keypad transmits key presses via radio
frequency to the RF receiver for accumulation by the PC. The keypad consists of 6 data keys
(1-5, and Channel) and a single status LED.
In Idle state, the LED is OFF. The keypad returns to idle state after completion of a key press.
Standard Operation Mode:
Initially the status LED is OFF.
Pressing a single key will cause the key to be transmitted to the receiver. After pressing a key
the status LED shows status as follows:
Quick YELLOW Blink then OFF
BLINKING YELLOW
SOLID GREEN
SOLID RED
BLINKING GREEN
BLINKING RED
- Receiver is not accepting data at this time
- key is being transmitted (up to 5 seconds)
- key transmit successful - ready for input
- key transmit failed – ready for input
- Receiver indicated correct answer
- Receiver indicated incorrect answer
Blinking Green and Blinking Red will only occur if the Receiver is configured to indicate a
correct or incorrect answer (CORRECT POLLING mode).
Set RF Channel
Press Channel Button
Set RF Channel mode is indicated by the status LED flashing a RED then GREEN pattern. Set
RF Channel mode exits automatically after two valid keys are pressed, if no valid key is pressed
for 5 seconds, or at any time an invalid key is pressed. Valid keys are ‘1’ through ‘5’. Valid RF
Channels are ‘11’ through ‘55’.
While in Set RF Channel mode pressing a valid key will cause the status LED to briefly flash
YELLOW. When Set RF Channel Mode exits, the status LED indicates the result as follows:
SOLID GREEN
SOLID RED
- Set RF Channel successful
- Set RF Channel failed
Display Software Version
Press ‘Channel’ and then quickly press and hold ‘2’. Release both keys.
The status LED will turn OFF briefly, followed by:
Major Version#
- Count the number of RED blinks – could be zero.
Minor Version#
- Count the number of YELLOW blinks – could be zero
REGULATORY INFORMATION
FCC Statement
This device complies with part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) This device may not cause harmful interference, and (2) this device must accept
any interference received, including interference that may cause undesired operation.
Changes or modifications not expressly approved by the party responsible for compliance could
void the user’s authority to operate the equipment.
Canada Statement
This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject
to the following two conditions: (1) this device may not cause interference, and (2) this device
must accept any interference, including interference that may cause undesired operation of the
device.
Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio
exempts de licence. L'exploitation est autorisée aux deux conditions suivantes : (1) l'appareil ne
doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage
radioélectrique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement
Safety Statement
WARNING, batteries may explode if mistreated. Do not recharge, disassemble or dispose in a
fire.
Replace batteries With Maxell, CR2032, 3-Volt Coin Cell ONLY. Use of another battery may
present risk of fire or explosion.
The disposal of used batteries is governed by law in many countries world-wide. Therefore,
please check your local regulations prior to battery disposal.

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.5
Linearized                      : Yes
Author                          : decrowder
Create Date                     : 2013:07:15 10:37:10-05:00
Modify Date                     : 2013:07:15 10:37:10-05:00
XMP Toolkit                     : Adobe XMP Core 5.4-c005 78.147326, 2012/08/23-13:03:03
Format                          : application/pdf
Title                           : Microsoft Word - RCSE-01 Keypad User Guide v1.1
Creator                         : decrowder
Creator Tool                    : PScript5.dll Version 5.2.2
Producer                        : Acrobat Distiller 11.0 (Windows)
Document ID                     : uuid:d084a0db-3ffc-407b-ba2f-ba880eab1f66
Instance ID                     : uuid:de155ef8-233f-4248-afed-2dcb94b26586
Page Count                      : 3

EXIF Metadata provided by EXIF.tools