Twinhead TABLETPC Tablet Computer with 802.11b and Bluetooth User Manual Users manual part 1
Twinhead International Corporation Tablet Computer with 802.11b and Bluetooth Users manual part 1
Twinhead >
Contents
- 1. Users manual part 1
- 2. Users manual part 2
- 3. Users manual part 3
Users manual part 1
U
Us
se
er
r’
’s
s
M
Ma
an
nu
ua
al
l
ii
Table Of Contents
CHAPTER 1
GETTING STARTED 1
Getting Started ................................................................................... 2
Inventory ............................................................................................. 3
Safety and Maintenance .................................................................... 4
Checklists ........................................................................................... 5
Features .............................................................................................. 6
Where to Look For Information ........................................................ 6
Quick Start .......................................................................................... 7
Loading Windows .............................................................................. 8
Adjusting the Volume ........................................................................ 9
Turning off Your Computer............................................................. 10
CHAPTER 2
GETTING STARTED 12
Hardware and Software ................................................................... 12
Front View......................................................................................... 13
Right View......................................................................................... 14
Top View............................................................................................ 15
Bottom View ..................................................................................... 16
Power Indicators .............................................................................. 17
Front View buttons........................................................................... 18
Function Keys .................................................................................. 19
Touch Pen......................................................................................... 19
Connecting the Floppy Disk Drive ................................................. 20
Disk Drives........................................................................................ 20
The CD-ROM, DVD-ROM, or Combo Drive..................................... 21
Connecting the Printer .................................................................... 21
The PCMCIA Card Slot..................................................................... 21
CF (Compact Flash) Card Slot ........................................................ 22
Memory.............................................................................................. 22
Communication Components......................................................... 25
CHAPTER 3
MAKING CONNECTIONS 28
Making Connections........................................................................ 28
Right Side Connectors .................................................................... 28
iii
Top Side Connectors....................................................................... 30
Bottom Side Connectors................................................................. 30
CHAPTER 4
POWER MANAGEMENT AND USING SOFTWARE 33
Power Management ......................................................................... 34
When to Replace the Battery .......................................................... 36
Heat Considerations ........................................................................ 36
Using Software ................................................................................. 37
APPENDIX A
STATEMENTS 39
Statements........................................................................................ 40
European Notice............................................................................... 42
UL CAUTION..................................................................................... 42
Canadian Department of Communications ................................... 43
Battery Disposal............................................................................... 44
CAUTION FOR ADAPTER................................................................ 44
BATTERY CAUTION......................................................................... 44
15.105 Federal Communications Commission (FCC)
Requirements, Part 15 ..................................................................... 44
APPENDIX B
INSTALLATION OF THE WIRELESS 47
Installation of the 802.11B Wireless .............................................. 48
Installation Precaution..................................................................... 48
Installing the WLAN Driver.............................................................. 49
Installation Notes - Windows XP .................................................... 51
Verifying a Successful Installation................................................. 55
Configuration for Windows XP ....................................................... 56
To Connect an Available Network via Wireless Zero Configuration
........................................................................................................... 56
To Configure the Wireless Networks Properties .......................... 57
To Access to Certain Wireless Network Type............................... 61
APPENDIX B
INSTALLATION OF THE BLUETOOTH 63
Setup for Windows 98/2000/ME/XP ................................................ 64
Application note for Windows 98SE/ME/2000/XP......................... 72
Icons used for Bluetooth devices and service ............................. 72
Network sharing setting for Windows ........................................... 75
iv
File transfer setting for Windows................................................... 81
Dial-up networking setting for Windows ....................................... 83
FAX setting ....................................................................................... 86
PIM Item Transfer setting ................................................................ 87
PIM Synchronization setting........................................................... 89
Serial Port setting ............................................................................ 91
ActiveSync setting........................................................................... 92
Audio Gateway setting for windows .............................................. 94
Personal area network setting for Windows ................................. 96
C
Ch
ha
ap
pt
te
er
r
1
1
I
In
nt
tr
ro
od
du
uc
ct
ti
io
on
n
Chapter 1 — Introduction
2
Getting Started
Congratulations on your purchase of a Tablet PC. The Tablet PC is a
fully functional PC with built-in LAN, and wireless Connectivity. With
your Tablet PC you will be able to organize and access important
business and personal information. In addition, you will be able to
send and receive e-mail and access the Internet.
This Manual contains all the information you need to set up and use
your Tablet PC. It describes all the features of the Tablet PC in an
easy-to-read yet thorough manner.
Introduction — Inventory
3
Inventory
This Tablet PC is designed for years of productive and pleasurable
computing. Use this section to keep details of your purchase. This
information will be required should you need to make repairs to your
Tablet PC during the warranty period. Update this section when you
add new options.
DATE OF PURCHASE:
PLACE OF PURCHASE:
DEALER'S NAME:
DEALER'S ADDRESS:
TELEPHONE:
E-MAIL ADDRESS/WWW:
CONTACT PERSON:
MODEL NUMBER:
SERIAL NUMBER:
BIOS VERSION:
Chapter 1 — Introduction
4
Safety and Maintenance
You can use your Tablet PC under a wide range of environmental
conditions. However, to ensure long use and continued high
performance, consider the following factors when setting up your
computer:
• Follow all warnings and instructions noted in this documentation
and in the Windows Help program.
• The first time you use your Tablet PC, we recommend that you
carefully read the Making Connections section of this manual
and initialize the battery to ensure optimum battery performance.
• Unplug the Tablet PC from the power outlet before cleaning. Use
a damp cloth for cleaning. Do not use aerosols, solvents, or
strong detergents.
• Slots and openings in the system cabinet are for ventilation
purposes. Do not block or cover these openings or the system
could overheat. Do not use or store the Tablet PC near a source
of heat or dust.
• On the base or rear panel of this Tablet PC, there is a label with
information on the power requirements of this system. These
requirements must be followed. If you are unsure of your local
power supply, consult your dealer or local Power Company.
• Do not step on or place anything on the power cord.
• If you use the Tablet PC with an extension cord, ensure that the
total ampere ratings of all the devices sharing the extension do
not exceed the rating of the extension cord or the rating of the
wall outlet.
• Never push foreign objects into the Tablet PC through any of the
slots or openings. Dangerous voltages are present, which could
cause electric shock or fire, or damage sensitive components.
Introduction — Checklists
5
Checklists
After opening the package, carefully inspect the contents. If any of the
items is missing or appear damaged, contact your dealer. The
shipping carton should contain the following:
STANDARD
• A notebook computer with a hard disk drive
• A standard battery
• An AC adapter with power cord
• User's Manual
• Driver CD
OPTIONS
The following items are normally optional, but some vendors may
include them in the standard package. Some items may not be
available in some countries, or some vendors may choose not to carry
all the items.
• 128/256/512MB SODIMM memory card
• Rugged carrying bag
• Stand holder
• Hand strip
• Second battery
• WLAN module
• Bluetooth module
Caution: When purchasing any of the accessories
listed above, purchase only those accessories that
are approved for use with your computer. The above
accessories are proprietary items. Your system
vendor can obtain these approved accessories. If
you use items that are not approved for use with
this Tablet PC, you may cause your computer to
malfunction, or to emit or receive electro-magnetic
radiation in excess of local regulations. For non-
proprietary accessories such as PC cards or
printers, ensure that the accessory functions
p
ro
p
erl
y
in
y
our Tablet PC before makin
g
the
Chapter 1 — Introduction
6
purchase. Your system vendor may be able to
recommend reliable brands and models.
Features
Software Included
Widows® XP Tablet PC Edition which includes:
• Microsoft® Internet Explorer
• Microsoft® Outlook Express
• Microsoft® Windows Media Player
High performance Processors
Ultra Low Voltage Mobile Intel PIII 866Mhz CPU or above FSB 133Mhz
CPU
High Capacity Hard Disk Drive
The Tablet PC has a high capacity hard disk drive, to store your favorite
programs and large multimedia files.
Built-in Wireless LAN, Modem and LAN Capability
A built-in 802.11b, 56k modem and 10/100 Mbps Ethernet port allows you
to access the Internet or a local area network (LAN).
Where to Look For Information
About Your Tablet PC
This User’s Manual describes the key elements of your Tablet PC.
New users can find a simple step-by-step orientation in the Quick
Start section of this chapter.
About Windows
The Windows Manual provides an overview of the Windows operating
System. Windows Online Help, found on the Start menu, offers extensive
Windows assistance. Welcome to Windows offers an online orientation for
new Windows users. Find it in:
Start/Programs/Accessories/System Tools.
Introduction — Quick Start
7
Quick Start
Turning on the Tablet PC for the First Time
1. Connect the AC adapter power cord to the AC adapter.
2. Connect the AC adapter to the DC power port on the bottom side of
your Tablet PC.
3. Connect the AC adapter power cord to an AC outlet.
4. Press the power button to turn on the power.
Note: The battery is not fully charged. Allow
your battery to fully charge before using it
(i.e., before disconnecting AC power).
Calibrating the battery before use is also
highly recommended. Refer to Chapter of Power
Management, for further information.
Chapter 1 — Introduction
8
Loading Windows
The following section is for installing the Windows operating system
only. If you are installing a different operating system, please check
with your vendor for installation details.
Product key number
Your Tablet PC will
begin loading Windows
once you turn on the
power. Wait a few
seconds for Windows
setup to load. The
Windows setup will
prompt you for the
product key number,
shown to the right:
Note: The product key is on a sticker
attached to the bottom of the Notebook.
1. Type your name, and, if applicable, the name of your company.
2. Read the End User's License Agreement. Click Next to accept it.
3. Enter the product key number. You can find this on the
Certificate of Authenticity on a sticker attached to the Tablet PC.
Click Finish.
4. The Start Wizard will prompt you to set the date, and your local
time.
After the Start Wizard updates your system settings, the Welcome to
Windows screen will appear. You may disable this feature by clearing
the check box labeled show this screen each time Windows starts.
Some software comes preloaded with Windows. New users can
familiarize themselves with this software by selecting Programs from
the start menu, then clicking on programs to run them.
Introduction — Adjusting the Volume
9
Adjusting the Volume
You can adjust the volume with hot key:
• Fn + Enter: volume down
• Fn + Escape: volume up
Alternatively, you can adjust
the volume with the Windows
volume control applet located
on the taskbar.
Adjusting the Brightness
Use the following hot key combinations to adjust the LCD panel
brightness:
• Fn + Security: decreases the brightness
• Fn + Rotate: increases the brightness
Chapter 1 — Introduction
10
Turning off Your Computer
Turning off the Tablet PC Tablet PC properly is important to
maintaining your computer.
1. On the Start menu, click
Shut Down. 2. Click the radio button next to
Shut Down in the Shut Down
Windows screen, and then click
OK.
If you are going to be away from the computer for a short period, there
are ways of conserving power without shutting down the system. See
Chapter 5, Power Saving Modes, for details.
Warning: Shutting off the Tablet PC improperly
may result in data loss.
C
Ch
ha
ap
pt
te
er
r
2
2
G
Ge
et
tt
ti
in
ng
g
S
St
ta
ar
rt
te
ed
d
Chapter 2 — Getting Started
12
Hardware and Software
This chapter introduces the different components and controls of your
Tablet PC, including the hardware components, the software, and the audio
and video systems.
Getting Started
Before you begin using your Tablet PC, read this chapter to familiarize
yourself with the main components installed in the system.
Getting Started — Front View
13
Front View
1. Speakers
2. Rotate
3. Security
4. Escape
5. Enter
6. Up/Down key
7. Function key
8. Internal microphone
9. Power source indicator
10. Battery charge status LED
11. Hard drive LED
12. Wireless LAN LED
13. LCD panel
14. Power button
Chapter 2 — Getting Started
14
Right View
1. CF card slot
2. Microphone-in jack
3. Audio-out jack
4. USB port
5. RJ-45 jack
6. DC-adaptor port
7. Stand holder connector
Getting Started — Top View
15
Top View
1. RJ-11 jack
2. PC card slot
3. Active stylus hole
4. Kensington lock hole
Chapter 2 — Getting Started
16
Bottom View
1. Back hand strap
2. Reset button
3. RF button
4. Second battery connector
5. Active stylus holder
Getting Started — Power Indicators
17
Power Indicators
The power indicators show which power source the system is using. They
also show battery status and low battery power alerts. The power indicators
remain active and viewable even when the LCD panel is closed.
Icon Light Description
T Blue Wireless LAN
Green
The Tablet PC is
reading from, or
writing to the built-in
hard disk.
Green Battery fully charged
Flashing
Orange
Battery charging
Flashing
Red
Battery power critically
low
Blue Power is on and the
battery is in use
Flashing
Blue
Power is in suspend
mode
Chapter 2 — Getting Started
18
Front View Buttons
The seven hot keys are unique features of your Tablet PC. The function
as follows:
Icon Function
Power Button
The Power button turns system on and goes into
standby automatically. If the unit has been sitting
unused for a while. Press momentarily to turn on
the system or to exit from standby. Press and hold
for at least 3-4 seconds to turn off the system.
These settings can be changed. For more
information, see the Windows XP Power
Management section in this user’s manual.
Rotation Button
Automatically changes position of the screen to
either portrait or landscape.
Security Button
Similar function as pressing Ctrl+Alt+Delete on a
standard keyboard.
Escape Button
Same function as on a standard keyboard.
Enter Button
Same function as on a standard keyboard.
UP/Down Button
Same function as scrolling button on a mouse.
Press the up button to scroll up in a document or
Web page; press the down button to scroll down in
a document or Web page.
Function Button
Access to secondary operation of some buttons
on the front bezel (shown in the illustration
above),user set up.
Getting Started — Function Keys
19
Function Keys
Hold the Fn key while pressing the function key.
Function key Description
Fn + Enter Volume down
Fn + Escape Volume up
Fn + Security Brightness down
Fn + Rotate Brightness up
Fn + Up Page up
Fn + Down Page down
Touch pen
The button located directly on the touch pen is the same in function as right
buttons on the mouse. Clicking button makes selections to perform a
variety of other functions depending on the software. To select an object,
first move the pointer over the object you want.
Chapter 2 — Getting Started
20
Connecting the Floppy Disk Drive
Your Tablet PC comes
with a USB port 1.44 MB
floppy disk drive (FDD is
optional). The FDD is “hot
pluggable,” so you do not
have to power down the
Tablet PC to connect it.
Disk Drives
Your Tablet PC comes with several components for reading and writing
(recording) information.
Floppy Disk Drive
The floppy disk drive provides a convenient way of storing and transferring
small files. The disk drive uses standard 3.5-inch, 1.44 MB disks. To use
the disk drive, insert a disk (label side up) into the drive slot and slide it all
the way in. To eject the disk from the drive, press the eject button. When
the Tablet PC is reading from or writing to a disk, the disk indicator light will
flash. Do not try to eject the disk when this light is active or you may lose
data.
Hard Disk Drive
The hard disk provides high-capacity storage and fast access. Windows
and most programs are stored here. Your Tablet PC identifies the hard disk
drive as drive C.
Floppy Disk Drive
USB connecto
r
Getting Started — The CD-ROM, DVD-ROM, or Combo Drive
21
The CD-ROM, DVD-ROM, or Combo Drive
Your Tablet PC comes with the CD-ROM, DVD-ROM, or Combo drive (It is
optional). The CD-ROM drive is a read-only drive. It cannot be used to write
data to a recordable CD. The CD-ROM drive can read data from CDs,
including audio or video CDs. The CD-RW can perform these same
functions, as well as record information to writeable CD's. The DVD drive
can read both DVDs and CDs. Your Tablet PC identifies the drive with the
letter following the hard drive letter. If your hard drive is D, then the CD-
ROM drive will be E.
Connecting the Printer
To connect a printer to your Tablet PC via the USB port, use the supplied
USB to printer adapter cable.
Note: Before use, you must install the driver for
the adapter cable.
The PC Card Slot
The PC card slot can be used as an interface between your Tablet PC and
a variety of communications devices, such as network adapters, SCSI
adapters, fax/modems, or provide additional data storage capacity. Your
computer's PC card slot supports PCMCIA Type II, 32-bit CardBus, and
Zoomed Video cards.
Note: Please read the instructions included with
individual PC cards. Some cards may be inserted
with power on, while others require that the
computer be turned off.
Chapter 2 — Getting Started
22
CF(Compact Flash)Card Slot
The CF card slot can be used as an interface between your Tablet PC and
a variety of devices, Insert a CF card in the CF Card Slot as shown below
unitl it snaps into place. Press the eject button to release the card.
Memory
Adding memory allows the Tablet PC to operate faster, handle more tasks
simultaneously, and work more smoothly with large files. Users who
increase memory demands - by adding additional programs, for example -
may notice a slowdown in operating speed, and wish to increase memory.
The Tablet PC includes a memory card slot for adding additional memory.
Note: Use only 1-inch SODIMM (PC-100) modules.
Calculate memory size by adding the size of the memory module to the
existing built-in memory. For example: 128 MB (module) + 128 MB (built-in
memory) = 256 MB Total
Replacing a Memory Card
Warning: Memory modules can be easily damaged by
static electricity. Leave the module inside its
static-proof bag until it is ready for installation.
Getting Started — Memory
23
Removing a Memory Card
1. Turn off the Tablet PC and disconnect the AC adapter. Turn the
computer upside down and lay it on a flat surface.
2. Carefully remove the two RAM compartment cover screws and
remove the RAM compartment cover.
3. Gently pull tabbed latched in the direction of the arrows (1). The
card will pop up slightly.
4. Pull upwards on the card and then slide the card out (2).
Chapter 2 — Getting Started
24
Inserting a Memory Card
1. Hold the memory card by its edges with the edge-connector
side towards the slot.
2. Hold the card at a shallow angle (about 25 degrees) and insert
the edge connector into the connector slot (3). The “gold teeth”
of the edge connector should no longer be visible when the
card is fully inserted.
3. Press the card downwards so that it is flat inside the
compartment (4). You may hear an audible click as the latches
of the connector lock the card in place.
4. Replace the RAM compartment cover and secure it with the two
screws.
Your Tablet PC will automatically detect the change in RAM capacity when
it restarts.
Getting Started — Communication Components
25
Communication Components
This system provides powerful communication functions, including built-in
Fax/Modem and PCMCIA card slot.
Fax/Modem
A phone jack on the top side of the computer allows you to connect to the
Internet to send and receive data. When used with fax software, it can be
used as a fax. When using this function, first plug the phone cord into the
jack.
C
Ch
ha
ap
pt
te
er
r
3
3
M
Ma
ak
ki
in
ng
g
C
Co
on
nn
ne
ec
ct
ti
io
on
ns
s
Chapter 3 — Making Connections
28
Making Connections
Your Tablet PC is equipped with a full array of ports and connectors,
including standard input/output (I/O) ports for quickly and easily adding
peripheral devices such as printers, keyboards, and mice. Refer to
documentation included with individual devices for details on
connecting these devices to your Tablet PC.
Right Side Connectors
1. CF Card Slot
Accepts devices that are designed to use CF card interface. Insert a
CF card in the CF Card Slot as shown above until it snaps into place.
Press the eject button to release the card.
2. Microphone-in Jack
Connect a microphone this jack to record audio.
Making Connections —Right Side Connectors
29
3. Audio-out Jack
Connect a stereo headset or external speakers to this jack to listen to
multimedia.
4. USB (Universal Serial Bus) Ports
The Universal Serial Bus (USB) is the latest standard for attaching
monitors, input devices, scanners, and other devices to a PC. USB
devices can be chained together on a single cable.
5. LAN RJ-45 Jack
With the built-in Ethernet LAN combo, you can make LAN connections
without installing PC cards. Connection speed is 10/100 Mbps. When
using the LAN function, wrap your LAN cable around the EMI ferrite
suppression box to inhibit electromagnetic interference.
6. DC-in Jack
Connect the DC power cable from the AC adapter to this jack.
7. Stand holder connector
Your Tablet PC comes with Stand holder (Stand holder is optional) for
battery charging. While the battery is charging, the battery charge
indicator of stand holder will be active.The two USB v1.1 ports and a
VGA port on stand holder to connect wide variety of devices.For more
information,please refer user’s guide of stand holder.
Chapter 3 — Making Connections
30
Top Side Connectors
1. Fax/modem RJ-11 Jack
The fax/modem can transmit data using the 56 Kbps V.90 protocol,
and send and receive faxes at 14.4 Kbps. In some countries, local
regulations may not permit the use of the fax/modem designed for this
system. In this case, you may use a PCMCIA modem.
Warning: Plug your modem into an analog telephone
jack only. Most homes use analog lines. Do
not use digital lines, such as the PBX and
ISDN systems found in many offices. Digital
lines may damage your modem.
2. PC Card Slot (PCMCIA)
Insert a PC Card (PCMCIA) card in the PC Card Slot as shown above
until it snaps into place. Press the eject button to release the card.
3. Kensington Lock
Your computer includes a Kensington lock hole to be used with a
standard Kensington lock. You can connect the notebook to a large
object with the Kensington lock to prevent theft of your notebook. See
Making Connections —Bottom Side Connectors
31
the documentation that comes with your Kensington lock for more
information.
Bottom Side Connectors
1. Second Battery Pack connector
Your Tablet PC comes with second battery pack (second battery pack
is optional) to prolong you work longer sesstions. You have to remove
the screw while you connect second battery pack to your Tablet PC.
For more information,see the section on Power Management in this
user guide.
C
Ch
ha
ap
pt
te
er
r
4
4
P
Po
ow
we
er
r
M
Ma
an
na
ag
ge
em
me
en
nt
t
a
an
nd
d
U
Us
si
in
ng
g
S
So
of
ft
tw
wa
ar
re
e
Chapter 4 — Power Management
34
Power Management
Checking the Battery Level
You can check the remaining battery power in the Windows® battery status
indicator located at the lower right-hand corner of the task tray. The Battery
Status icon only appears in the task tray while the unit is running on the
battery power but not while the unit is running off an external power source
through the AC adaptor.
Battery Power Indicator
Monitoring Battery Power
There are two ways to
monitor how much power the
battery has left.
1. Click Start / Settings /
Control Panel / Power
Options ; then click
Power Meter.
2. Moving the cursor to the
battery icon on the
taskbar is the simplest
way to check on battery
power status.
If you do not see the battery icon, enable it in Start / Settings /
Control Panel / Power Options . Choose the Advanced tab and click
“Always show icon on the taskbar.”
Low Battery Alarms
How your Tablet PC responds to a low battery condition is set under
Start / Settings / Control Panel / Power Options / Alarms.
Two different power alarms can be enabled or disabled: the Low
Battery Alarm, and the Critical Battery Alarm.
Power Management — Power Management
35
Warning: When battery power is low, the battery
indicator will flash red, and the alarm will
display a warning on your screen. Take immediate
action, such as saving files or connecting to the
AC adapter, or data may be lost.
Battery Charging
When you use the AC adapter to connect your Tablet PC to a power
outlet, the internal battery will automatically begin to recharge. While
the battery is charging, the Battery Charge icon on the Indicator panel
will be active after 6~12 seconds. When the battery is fully charged,
the Battery Charge icon will turn off.
If your Tablet PC is turned off, a fully discharged battery will take about
3 hours to recharge. If your computer is turned on and is not in
suspend mode, it twill take about 6~13 hours to recharge the battery.
Refer to the following table:
Charging Discharging
System On 6~13 hours 3.5 hours
System Off
(suspend to RAM) 3 hours —
Note: A fully charged Li-Ion battery can run the
Tablet PC for approximately 3.5 hours. (According
to Battery Mark benchmark tests）
Chapter 4 — Power Management
36
When to Replace the Battery
Over time, the battery's capacity gradually decreases. We recommend
that you replace your battery when you notice that it begins to store
significantly less charge.
Changing the Battery
Change the main battery pack as follows:
1. Turn off the Tablet PC.
2. To replace the Battery remove the
screw and the Battery Bay Cover
shown right
3. Make sure the replacement battery is properly orientated. Then
insert the battery into the battery compartment. Check that the
latch locks back into position.
Heat Considerations
The Tablet PC processor has been specially designed to consume
little power, and generates very little heat. However, working in a hot
environment, or working for long periods may raise the temperature.
Your Tablet PC takes the following steps to lower temperature:
1. The cooling fan will automatically turn on. You may feel air coming
from a vent at the left side when this happens.
2. If the temperature continues to rise, processor activity will be
reduced. You may notice a slight loss of performance when this
happens.
Warning:If the operating temperature exceeds 35 oC,
the system will shut down to prevent the
heat from damaging the computer’s
infrastructure. When the computer cools to
a normal temperature you can restart the
system. The higher the temperature of the
environment, the longer the period the
computer will need to cool down.
Power Management — Using Software
37
Using Software
Touch Screen Calibration
The touch screen is a thin membrane on the top of the LCD display that
responds to mechanical pressure on the screen’s surface. The cursor on
the screen is controlled using the stylus. If you notice the stylus tip touch-
point not matching up with the cursor, you can recalibrate the touch screen.
Calibrating the Touch Screen
1. Click the Windows® Start button > Control Panel > Switch to Classic
View > Tablet and Pen Settings. Under the Setting tab, click Calibrate
and follow the on-screen instructions shown below.
Chapter 4 — Power Management
38
2. Click the stylus in the middle of the crosshairs. The wheel moves to
another location on-screen.
3. Repeat the exercise as above several times until the screen returns to
the Calibration Applet
4. Click OK, The recalibration tales place immediately upon exciting the
application. No need to restart the Tablet PC.
Screen Rotation
To rotate the screen the screen form Portrait to Landscape mode or vice
versa, press the Rotate button on the front of the Tablet PC. Please refer
chapter 2 in this user’s manual.
A
Ap
pp
pe
en
nd
di
ix
x
A
A
S
St
ta
at
te
em
me
en
nt
ts
s
Appendix A — Statements
40
Statements
Federal Communications Commission Statement
This equipment has been tested and found to comply with the limits for
a Class B digital device, pursuant to Part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates,
uses, and can radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee
that interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or
more of the following measures:
1. Reorient or relocate the receiving antenna.
2. Increase the separation between the equipment and the receiver.
3. Connect the equipment into an outlet on a circuit different from
that to which the receiver is connected.
4. Consult the dealer or an experienced radio/TV technician for
help.
Shielded interconnect cables and shielded AC power cable must be
employed with this equipment to insure compliance with the pertinent
RF emission limits governing this device. Changes or modifications not
expressly approved by the system's manufacturer could void the
user's authority to operate the equipment.
Declaration of Conformity
This device complies with part 15 of the FCC rules. Operation is
subject to the following conditions:
• This device may not cause harmful interference
• This device must accept any interference received, including
interference that may cause undesired operation.
Appendix A — Statements
41
About The Modem
This equipment complies with Part 68 of FCC rules. On the bottom of
this equipment is a label that contains, among other information, the
FCC registration number and ringer equivalence number (REN) for
this equipment. If requested, this information must be provided to the
telephone company.
The modem jack of this equipment complies with Sub-part F of Part 68
of FCC rules.
The REN is used to determine the quantity of devices that may be
connected to the telephone line. Excessive RENs on the telephone
line may result in the devices not ringing in response to an incoming
call. In most, but not all areas, the sum of the RENs should not exceed
five (5.0). To be certain of the number of devices that may be
connected to the line, as determined by the total RENs contact the
telephone company to determine the maximum REN for the calling
areas.
If the terminal equipment causes harm to the telephone network, the
telephone company will notify you in advance that temporary
discontinuance of service may be required. However, if advance notice
isn't practical, the telephone company will notify the customer as soon
as possible. Also, you will be advised of your right to file a compliant
with the FCC if you believe it necessary.
The telephone company may mark changes in its facilities, equipment,
operations, or procedures that could affect the operation of the
equipment. If this happens, the telephone company will provide
advance notice in order for you to make the necessary modifications in
order to maintain uninterrupted service.
If trouble is experienced with this equipment, please contact the
manufacturer for repair and (or) warranty information. If the trouble is
causing harm to the telephone network, the telephone company may
request you remove the equipment from the network until the problem
is resolved.
The equipment cannot be used on public coin service provided by the
telephone company. Connection to Party Line Service is subject to
state tariffs. (Contact the state public utility commission, public service
commission or corporation commission for information.)
Appendix A — Statements
42
The Telephone Consumer Protection Act of 1991 marks it unlawful for
any person to use a computer or other electronic device, including fax
machines, to send any message unless such message clearly
contains in a margin at the top or bottom of each transmitted page or
on the first page of the transmission, the date and time it is sent and
an identification of the business or other entity, or other individual
sending the message and the telephone number of the sending
machine or such business, other entity, or individual. (The telephone
number provided may not be a 900 number or any other number for
which charges exceed local or long-distance transmission charges.)
To program this information, refer to the manual of the communication
software.
European Notice
Products with the CE Marking comply with both the EMC Directive
(89/336/EEC) and the Low Voltage Directive (73/23/EEC) issued by
the Commission of the European Community.
Compliance with these directives implies conformity to the following
European Norms:
EN 55022 ( CISPR 22 ) Radio Frequency Interference
EN 55024 ( EN61000-4-2, EN61000-4-3, EN61000-4-4, EN61000-4-5,
EN61000-4-6, EN61000-4-8,EN61000-4-11, EN61000-3-2, EN61000-
3-3 ) Generic Immunity Standard
EN 60950 ( IEC950 ) Product Safety
UL CAUTION
To reduce the risk of fire, use only No. 26 AWG or larger
telecommunication line cord.
IMPORTANT SAFETY INSTRUCTIONS
When using your telephone equipment, basic safety precautions
should always be followed to reduce the risk of fire, electric shock and
injury to persons, including the following:
Do not use this product near water, for example, near a bathtub, wash
bowl, kitchen sink or laundry tub, in a wet basement or near a
swimming pool.
Appendix A — Statements
43
Avoid using a telephone (other than a cordless type) during an
electrical storm. There may be a remote risk of electric shock from
lightning.
Do not use the telephone to report a gas leak in the vicinity of the leak.
Use only the power cord and batteries indicated in this manual. Do not
dispose of batteries in a fire. They may explode. Check with local
codes for possible special disposal instructions.
Canadian Department of Communications
This class B digital apparatus meets all requirements of the Canadian
Interference-causing Equipment Regulations.
About the Modem
The Industry Canada label identifies certified equipment. This
certification means that the equipment meets certain
telecommunications network protective, operational and safety
requirements. The department does not guarantee the equipment will
operate to the user's satisfaction.
Before installing this equipment, users should ensure that it is
permissible to be connected to the facilities of the local
telecommunications company.
The equipment must also be installed using an acceptable method of
connection. In some cases, the company's inside writing associated
with a single line individual service may be extended by means of a
certified connector assembly (telephone extension cord). The
customer should be aware that compliance with the above conditions
may not prevent degradation of service in some situations.
Repairs to certified equipment should be made by an authorized
Canadian maintenance facility designated by the supplier. Any repairs
or alterations made by the user to this equipment, or equipment
malfunctions, may give the telecommunications company cause to
request the user to disconnect the equipment.
Users should ensure for their own protection that the electrical ground
connections of the power utility, telephone lines and internal metallic
water pipe system, if present, are connected together. This precaution
may be particularly important in rural areas.
Appendix A — Statements
44
CAUTION: Users should not attempt to make such connections
themselves, but should contact the appropriate electric
inspection authority, or electrician, as appropriate.
"The Load Number (LN) assigned to each terminal device denotes the
percentage of the total load to be connected to a telephone loop which
is used by the device. To prevent overloading, the termination on a
loop may consist of any combination of devise subject only to the
requirement that the total of the Load Numbers of all the devices does
not exceed 100."
Battery Disposal
THIS PRODUCT CONTAINS A LITHIUM-ION OR NICKEL-METAL HYDRIDE
BATTERY. IT MUST BE DISPOSED OF PROPERLY. CONTACT LOCAL
ENVIRONMENTAL AGENCIES FOR INFORMATION ON RECYCLING AND
DISPOSAL PLANS IN YOUR AREA.
CAUTION FOR ADAPTER
THIS TABLET PC IS FOR USE WITH MODEL NO. LSE9802A2060
BATTERY CAUTION
DANGER OF EXPLOSION IF BATTERY IS INCORRECTLY REPLACED.
REPLACE ONLY WITH THE SAME OR EQUIVALENT TYPE RECOMMENDED BY
THE MANUFACTURER. DISPOSE OF USED BATTERIES ACCORDING TO THE
MANUFACTURER'S INSTRUCTIONS.
15.105 Federal Communications Commission
(FCC) Requirements, Part 15
This equipment has been tested and found to comply with the limits for
a class B digital device, pursuant to part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation.
This equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined
Appendix A — Statements
45
by turning the equipment off and on, the user is encouraged to try to
correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from
that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for
help.
Regulatory information / Disclaimers
Installation and use of this Wireless LAN device must be in strict
accordance with the instructions included in the user documentation
provided with the product. Any changes or modifications (including the
antennas) made to this device that are not expressly approved by the
manufacturer may void the user’s authority to operate the equipment.
The manufacturer is not responsible for any radio or television
interference caused by unauthorized modification of this device, or the
substitution of the connecting cables and equipment other than
manufacturer specified. It is the responsibility of the user to correct any
interference caused by such unauthorized modification, substitution or
attachment. Manufacturer and its authorized resellers or distributors
will assume no liability for any damage or violation of government
regulations arising from failing to comply with these guidelines.
FCC RF Radiation Exposure Statement:
This Transmitter has been demonstrated co-location compliance
requirements with (Bluetooth / Model no: MUBTC2TH). This
transmitter must not be co-location or operating in conjunction with any
other antenna or transmitter.
This equipment complies with FCC RF radiation exposure limits set
forth for an uncontrolled environment. This device was tested for
typical lap held operations with the device contacted directly to the
human body to the backside of the notebook computer. To maintain
compliance with FCC RF exposure compliance requirements, avoid
direct contract to the transmitting antenna during transmitting.
SAR Exposure
This device has been tested for compliance with FCC RF Exposure
(SAR) limits in typical flat configurations.
Appendix A — Statements
46
For LPD
“Operation is subject to the following two conditions: (1) this device
may not cause interference, and (2) this device must accept any
interference, including interference that may cause undesired
operation of the device.”
W/detachable antenna
“To reduce potential radio interference to other users, the antenna
type and its gain should be so chosen that the equivalent isotropically
radiated power (EIRP) is not more than that required for successful
communication.”
This Class B digital apparatus complies with Canada RSS-210.
Cet appareil numérique de la classe B est conforme à la norme CNR-
210 du Canada
The abbreviation, IC, before the registration number signifies that
registration was performed based on a Declaration of Conformity
indicating that Industry Canada technical specifications were met. It
does not imply that Industry Canada approved the equipment. (DoC)
The term “IC:” before the certification/registration number only signifies
that the Industry Canada technical specifications were met.
A
Ap
pp
pe
en
nd
di
ix
x
B
B
I
In
ns
st
ta
al
ll
la
at
ti
io
on
n
o
of
f
t
th
he
e
W
Wi
ir
re
el
le
es
ss
s
Appendix B — Installation of the Wireless
48
Installation of the 802.11B Wireless LAN
It’s free and easy for you to install your 802.11b Wireless LAN USB
Module and the attached software - WLAN 11Mbps WM168b.
To have the 802.11b WLAN USB Module operated appropriately,
please read and go along with the instructions below carefully.
Installation Precaution
Before the installation, please ensure the 802.11b WLAN USB Module
has already located in your laptop computer. To detect the existence
of the Module, please follow the procedures below.
a) Click Start on the taskbar and choose Control Panel from the
Settings menu.
b) Select System to open the System Properties dialog box, and
then under the Hardware tab, click the Device Manager button
to open the Device Manager dialog box.
c) Double-click Other devices from the list to display the item -
IEEE 802.11b PRISM3 USB, and this presents the existence of
your 802.11b WLAN USB Module.
Installation of the Wireless — Installation of the 802.11b Wireless LAN
49
Figure A-1: The Device Manager Dialog Box
Note: In contrast, if you don’t find the module
accordingly, please contacts your dealer
immediately.
Now you may proceed with the next topic to start installing the drivers
for the module.
Installing the WLAN Driver
a) Insert the supplied Setup CD into your CD-ROM drive, and the
Setup Wizard will run automatically. If it does not, please
manually execute autorun.exe.
b) From the prompted startup window, choose Install WLAN
Driver to begin the installation.
Appendix B — Installation of the Wireless
50
Figure A-2: The Startup Window
c) Click Next in the WLAN 11Mbps WM168b window to proceed.
The system will start to copy the drivers found.
Figure A-3: The WLAN 11Mbps WM168b Window
Installation of the Wireless — Installation of the 802.11b Wireless LAN
51
d) On the Reboot screen, choose Yes, I want to restart my
computer now, and then click Finish to restart the computer.
Figure A-4: The Reboot Screen
e) After rebooting, you can shall find the WLAN 11Mbps
WM168b icon, , appeared in the system tray. The installation
is entirely finished at the moment. Double-click the icon to
launch the program and open the PRISM Wireless Settings
dialog box, in which you may freely arrange your network
connection afterwards.
For more details about WLAN 11Mbps WM168b, please refer to
WLAN 11Mbps WM168b Basics in this manual.
Installation Notes - Windows XP
If your current system is running Windows XP, you shall find that two
tabs are contained in the PRISM Wireless Settings dialog box after
you’ve followed the instructions above and successfully installed the
drivers. However, normally, the dialog box should be consisted of five
Appendix B — Installation of the Wireless
52
tabs. This is because Windows XP has its built-in configuration tools –
Windows XP Zero Configuration to assist you in networking activities.
It is recommended to utilize the attached WLAN 11Mbps WM168b to
enjoy more benefits it will bring. Thus, to employ your WLAN 11Mbps
WM168b under Windows XP, please proceed to the next step to change
the default settings of Windows Zero Configuration to WLAN 11Mbps
WM168b.
Figure A-5: The WLAN 11Mbps WM168b Tray Icon
Figure A-6: The PRISM Wireless Settings Dialog Box
a) Right-click the Network Connections icon at the task bar to
open the Wireless Network Connection Status dialog box,
and then select Properties.
Installation of the Wireless — Installation of the 802.11b Wireless LAN
53
Figure A-7: The Wireless Network Connection Status Dialog Box
b) Choose the Wireless Networks tab in the Wireless Network
Connection Properties dialog box, and remove the tick in the
Use Windows to configure my wireless network settings
checkbox.
Appendix B — Installation of the Wireless
54
Figure A-8: The Wireless Network Connection Properties Dialog
Box
c) Click OK. Now, you have successfully removed the Windows
Zero Configuration.
To monitor and configure the network via WLAN 11Mbps
WM168b, double-click its tray icon, and you should find four
tabs contained in the popped up PRISM Wireless Settings
dialog box at this time. For more details about the program,
please refer to WLAN 11Mbps WM168b Basics below.
Installation of the Wireless — Installation of the 802.11b Wireless LAN
55
Verifying a Successful Installation
To confirm that your 802.11b Wireless LAN USB Module is properly
installed, please go along with the procedures below.
a) Right-click the My Computer desktop icon and choose
Properties from the opened menu.
b) In the System Properties dialog box, choose Device
Manager if you are under Windows 98 or Me. If you are
operating Windows 2000 or XP, click the Hardware tab, and
then choose the Device Manager button.
c) In the opened window, expand Network adapters to find the
USB Module – Wireless LAN 11Mbps WM168 USB Module.
Right-click over the item and choose Properties.
d) From the opened dialog box, on the General tab, find the
descriptions under the Device Status pane to learn if the
module is working properly. However, if there’s an error
message shown, please choose Uninstall from the opened
menu while right-clicking over the USB Adapter item, to which
a red or yellow icon is attached beside, in the Device
Manager dialog box. Then restart your system and go
through the installation procedures again.
The following picture indicates a successful installation of the 802.11b
Wireless LAN USB Module.
Figure A-9: The Device Manager Dialog Box
Appendix B — Installation of the Wireless
56
Configuration for WIndows xp
As you have already known, Windows XP has its built-in configuration
tools – Windows XP Zero Configuration, to assist you in some basic
configurations of wireless network connection. The service starts right
after the completion of the installation of 802.11b WLAN USB Module,
and you will find the icon automatically appears in your system tray
like the following picture shows.
Figure A-10: The Wireless Network Connection Icon
Please refer to the desired topics below to look for more details about
utilizing your 802.11b WLAN USB Module via Wireless Zero
Configuration.
To Connect an Available Network via Wireless Zero
Configuration
1. Double-click the Wireless Network Connection icon.
2. In the opened Connect to Wireless Network dialog box, the
currently available networks are listed in the Available
networks field. From the list, click an item, which you intend to
make an association.
3. If the chosen entry requires a WEP encryption key and also
automatically provides it, leave the Network Key field blank and
then choose the Connect button to build the connection.
Otherwise, you will need to manually enter the identical key in
the Network Key field before clicking Connect.
Installation of the Wireless — Configuration for WIndows xp
57
Figure A-11: The Connect to Wireless Network Dialog Box
4. If the connection is established, there will be a pop-up message
shown beside the Wireless Network Connection icon on the
system tray. You could obtain the information on the status of
connection from the message.
To Configure the Wireless Networks Properties
If you cannot establish a connection with the chosen entry or you wish
to configure further wireless network connection settings, choose the
Advanced button in the Connect to Wireless Network dialogue box.
Figure A-12: The Connect to Wireless Network Dialog Box
Appendix B — Installation of the Wireless
58
After clicking Advanced, you will enter into the Wireless Networks
tab of the Wireless Network Connection Properties dialog box, in
which three other tabs are found, including General, Authentication,
and Advanced. The Wireless Networks tab includes almost the main
settings for the networking connection. Thus, please check the
descriptions below to learn more about the tab.
Figure A-13: The Wireless Network Connection Properties Dialog
Box
Note: For more detailed information about each tab, please
refer to the Windows XP Online-Help.
The Wireless Networks tab is mainly consisted of two sections:
Available networks and Preferred networks.
Under the Available networks area, all the available access points or
Wireless LAN PC Card equipped computers are displayed. You may
wish to click Refresh to update the list. If you choose any listed item
in the field and then click Configure, the Wireless Network
Installation of the Wireless — Configuration for WIndows xp
59
Properties dialog box will appear as Figure 3-5 shows. Check the
description below the figure to obtain more information about the
dialog box.
In the Preferred networks area, you could add any displayed
networks to the list by clicking over the intended item from Available
networks and then selecting the Add button. After clicking Add, the
Wireless Network Properties dialog box will appear as Figure 3.2-3
displays. Note that to delete any item under the Preferred networks
area, simply click on it and then select the Remove button.
Additionally, you may adjust the items in the list by clicking the
desired item and then choosing the Move up or Move down button. It
is, however, important to realize that Windows XP will always choose
the first one in the list to establish the networking connection.
Figure A-14: The Wireless Network Properties Dialog Box
In the opened Wireless Network Properties dialog box, edit texts in
the Network Name (SSID) field to identify the chosen network entry
in the wireless LAN.
If there’s a need, go to the Wireless network key (WEP) area below
to set the keys as the associated access point or Wireless LAN PC
Card equipped computer requests. To set WEP, select Data
encryption (WEP enabled) and Network Authentication. Then
enter the encryption keys for the network you intend to connect in the
Network Key field. Meanwhile, the Key format and Key length
Appendix B — Installation of the Wireless
60
options change the settings according to Network Key string you just
typed. Click OK when you are finished, and you will return to the
Wireless Network Connection Properties dialog box.
Figure A-15: Enter WEP
Note: For more details of this tab, you may click the
link: setting up wireless network configuration at
the bottom of the Wireless networks tab to launch
the Windows XP Online-Help.
Installation of the Wireless — Configuration for WIndows xp
61
Figure A-16: Setting up wireless network configuration
To Access to Certain Wireless Network Type
The default network type of Windows XP Zero Configuration is any
available access points (Access Point mode) or WLAN Card equipped
computer (Ad-Hoc mode) within the range at the given time. However,
you may wish to connect to a certain network type sometimes. To
change the default settings, click the Advanced button in the
Wireless Network Connection Properties dialog box.
Appendix B — Installation of the Wireless
62
Figure A-17 The Advanced Dialog Box:
The open Advanced dialog box provides three options, Any available
network, Access point networks only, and Computer-to-computer
networks only. Choose one of them according to your need and click
Close to finish. Then you will find under the Available networks area
in the Wireless Network Connection Properties dialog box, only the
specified networks are displayed.