Tyco Safety Canada 09WT4901 Wireless Indoor Siren User Manual

Digital Security Controls Ltd. Wireless Indoor Siren

User Manual

Use this installation sheet along with the associated alarm system installationmanual. All instructions specified within that manual must be observed.The WT4901 is a two-way wireless indoor siren. It sounds an alarm conditionreceived via DSC wireless protocol from a compatible, two-way enabled securitypanel (e.g., PC9155). After the WT4901 is enrolled on the security panel, it iscapable of receiving commands from the panel for sounding alarms and com-municating any required response, such as system status. The siren is capable ofsounding different alarm cadences (e.g., continuous burglary, pulsating fire(used in Canada), or temporal three fire (used in USA)), bell squawks, andbuzzer tones to suit the type of command it receives. The WT4901 provides a supervisory signal to the security panel, to ensurethat its wireless communication capability is currently functioning. In addi-tion, it monitors the case and wall tamper switch states, and the batterystate. In the event of a low battery or a tamper activation, the WT4901 trans-mits the appropriate signal to the security panel and, if applicable, providesan audible indication that a system event has occurred. Multiple WT4901can be enrolled on, and supervised by the same security panel as separateunits.Specifications• Operating Temperature: -10°C to +55°C (14°F to 131°F)Temperature range for UL/ULC: 0°C to +49°C• Relative Humidity: 0 to 93% R.H., non-condensing• Operating Frequency: 433.92MHz• Wireless Range: 250m (outdoor, line of sight)•Batteries: (4) AA 1.5V Alkaline (Duracell, Panasonic or Energizer)• Battery Life: 2 years (under typical use)• Low Battery Level: {xx V pre-determined}•Output Level: 85dB @ 3m(high volume)/65db @ 3m(medium volume)Out of the Box WT4901 Installation Sheet Hardware pack: 3 screws and 3 plastic anchors 4 AA BatteriesTwo-Way Wireless Siren EnrollmentThe WT4901 serial number is only used when the indoor siren is enrolled and pow-ered up. Enrolling the WT4901 permits it to communicate with the control panel.The installer can activate the indoor siren by Quick Enrollment or Serial NumberProgramming, see below.NOTE: Make sure the Keypad is setup before activating the indoor siren.Quick Enrollment1. Enter the enrollment mode through installer programming, see section [898] inthe alarm system installation manual.2. Power up the indoor siren, if it is not already powered up.3. Tamper the indoor siren using the tamper switch.4. The indoor siren sends a request to the security panel to enroll on the system.5. The Keypad displays the electronic serial number which must be confirmed bykeying in [*]. If the electronic serial number is incorrect, press [#] and repeatthis step.6. Select the module number that the device should be enrolled as.NOTE: The electronic serial number is a 8-digit alphanumeric numberlocated on a sticker on the wireless device.7. Repeat starting from step 2. to enroll each additional indoor siren.Serial Number Programming1. Enter the enrollment mode through installer programming, see section [804] inthe alarm system installation manual.2. Select the module number that the device will be enrolled as. See sections [301]-[304] for sirens.3. Enter the serial number using either the Keypad, or DLS.Placement TestPerform a placement test to ensure there is sufficient signal strength for proper com-munication between the security panel and the siren location.1. Place the security panel into placement test, see section [906].2. Start the test by tampering and restoring the siren being tested, or pressing andholding the Test button for 2 seconds (the siren will give a beep).3. The siren will respond with one beep if the location is “Good” or three beeps if thesiren is at a “Bad” location.Physical InstallationThe indoor siren is mounted to a flat surface such as drywall, or any variety of othersurfaces with the supplied hardware. NOTE: When mounting the WT4901 on drywall the use of the plastic anchorsis mandatoryNOTE: Do not mount over a single gang electrical box.1. Open the WT4901 by inserting a screwdriver into the slots and gently pry on thefront cover until it separates from the backplate.2. If the batteries are not installed, install the batteries as shown in the sequenceindicated by the engraving.3. Position the backplate on a flat mounting surface and mark this location.4. Secure the backplate to the mounting surface with all the screws provided.5. Hinge the front cover to the backplate carefully, to correctly align it with thetamper switch, then snap it onto the backplate. The wall tamper switch mustremain closed when the indoor siren is mounted.Test ButtonThe test button activates the local siren for 4 seconds. Press and hold the siren testbutton, located at the front of the WT4901, to verify the indoor siren is functioning.If it is, the siren will sound at medium volume for 2 seconds, followed by 2 secondsat full volume. The WT4901 does not necessarily have to be enrolled on a system toperform this test.Battery ReplacementThe security panel will indicate when the batteries are low and require replacement. Pana-sonic, Duracell or Energizer 1.5V AA alkaline batteries can be used. REPLACE ONLY WITHTHE TYPE RECOMMENDED BY THE MANUFACTURER. Open the front cover andinstall the batteries as shown in the sequence indicated by the engraving. If the batteries areinstalled incorrectly, in the reverse polarity, the indoor siren will not work. Under typical usethe WT4901 is capable of operating on battery power alone without having to change thebatteries for a minimum period of two years. Do not try to recharge these batter-ies. Disposal of used batteries must be made in accordance with thewaste recovery and recycling regulations in your area.Configuration and TestingIf necessary, WT4901 options can be setup to suit desired system responses. Bymeans of the keypad interface, the installer has access to the siren programmingmenus supported by the main panel e.g., wireless sounder options (see tablebelow), siren enrollment and placement test activation menu.EnglishInstallation InstructionsSiren # Serial Number[301]#1[302]#2[303]#3[304]#4Program Section OptionsSounder:Siren#1[311]Siren#2[312]Siren#3[313]Siren#4[314]1. Siren Enabled2. Buzzer Notification Enabled3. Door Chime Enabled4. Trouble Beeps Enabled5. Bell Squawks Enabled6. Enable Strobe (WT4911 only)7. Buzzer Alarms follow BTO8. For Future Use1. Siren Disabled2. Buzzer Notification Dis-abled3. Door Chime Disabled4. Trouble Beeps Disabled5. Bell Squawks Disabled6. Disable Strobe (WT4911 only)7. Buzzer Alarms follows Alarm Condition8. For Future UseGlobal Sounder:Sirens#1-4 [320]1. Tamper Activates Siren/Strobe2. Pre-Alarm Signal Enabled3. to 8. For Future Use1. Tamper does not Acti-vate Siren/Strobe2. Pre-Alarm Signal Dis-abled3. to 8. For Future UseTest ButtonBuzzer9035MountingHoles (2)Mounting HoleBattery (4) AA1.5V AlkalineTest ButtonSlots for removingfront cover9036Indoor Siren Front Cover Indoor Siren Backplate
Limited WarrantyDigital Security Controls warrants that for a period of 12 months from thedate of purchase, the product shall be free of defects in materials andworkmanship under normal use and that in fulfilment of any breach ofsuch warranty, Digital Security Controls shall, at its option, repair orreplace the defective equipment upon return of the equipment to its repairdepot. This warranty applies only to defects in parts and workmanshipand not to damage incurred in shipping or handling, or damage due tocauses beyond the control of Digital Security Controls such as lightning,excessive voltage, mechanical shock, water damage, or damage arisingout of abuse, alteration or improper application of the equipment. Theforegoing warranty shall apply only to the original buyer, and is and shallbe in lieu of any and all other warranties, whether expressed or impliedand of all other obligations or liabilities on the part of Digital Security Con-trols. Digital Security Controls neither assumes responsibility for, norauthorizes any other person purporting to act on its behalf to modify or tochange this warranty, nor to assume for it any other warranty or liabilityconcerning this product. In no event shall Digital Security Controls be lia-ble for any direct, indirect or consequential damages, loss of anticipatedprofits, loss of time or any other losses incurred by the buyer in connectionwith the purchase, installation or operation or failure of this product.Warning: Digital Security Controls recommends that the entire sys-tem be completely tested on a regular basis. However, despite fre-quent testing, and due to, but not limited to, criminal tampering orelectrical disruption, it is possible for this product to fail to performas expected. Important: Changes or modifications not expresslyapproved by Digital Security Controls could void the user’s authorityto operate this equipment.FCC Compliance StatementCAUTION: Changes or modifications not expressly approved by Digital Security Controls could void your authority to use this equipment. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.IC: 160A-WT4901 The term ‘IC:’ before the radio certification number only signifies that Industry Canada technical specifications were met.This Class B digital apparatus complies with Canadian ICES-003. Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.This product meets the requirements of Class II, Grade 2 equip-ment as per EN50131-1 and EN50131-4 Standards. The power supply is Type C as per EN50131-6 Standard.IMPORTANT - READ CAREFULLY: DSC Software purchased with or without Prod-ucts and Components is copyrighted and is purchased under the following license terms:• This End-User License Agreement (“EULA”) is a legal agreement betweenYou (the company, individual or entity who acquired the Software and anyrelated Hardware) and Digital Security Controls, a division of Tyco SafetyProducts Canada Ltd. (“DSC”), the manufacturer of the integrated securitysystems and the developer of the software and any related products or com-ponents (“HARDWARE”) which You acquired. • If the DSC software product (“SOFTWARE PRODUCT” or “SOFT-WARE”) is intended to be accompanied by HARDWARE, and is NOTaccompanied by new HARDWARE, You may not use, copy or install theSOFTWARE PRODUCT. The SOFTWARE PRODUCT includes com-puter software, and may include associated media, printed materials, and“online” or electronic documentation. • Any software provided along with the SOFTWARE PRODUCT that isassociated with a separate end-user license agreement is licensed to Youunder the terms of that license agreement. By installing, copying, downloading, storing, accessing or otherwise using the SOFTWARE PRODUCT, You agree unconditionally to be bound by the terms of this EULA, even if this EULA is deemed to be a modification of any previ-ous arrangement or contract. If You do not agree to the terms of this EULA, DSC is unwilling to license the SOFTWARE PRODUCT to You, and You have no right to use it.SOFTWARE PRODUCT LICENSEThe SOFTWARE PRODUCT is protected by copyright laws and international copy-right treaties, as well as other intellectual property laws and treaties. The SOFTWAREPRODUCT is licensed, not sold. 1. GRANT OF LICENSE This EULA grants You the following rights:(a) Software Installation and Use - For each license You acquire, You may have onlyone copy of the SOFTWARE PRODUCT installed. (b) Storage/Network Use - The SOFTWARE PRODUCT may not be installed,accessed, displayed, run, shared or used concurrently on or from different computers,including a workstation, terminal or other digital electronic device (“Device”). In otherwords, if You have several workstations, You will have to acquire a license for eachworkstation where the SOFTWARE will be used.(c) Backup Copy - You may make back-up copies of the SOFTWARE PRODUCT,but You may only have one copy per license installed at any given time. You may usethe back-up copy solely for archival purposes. Except as expressly provided in thisEULA, You may not otherwise make copies of the SOFTWARE PRODUCT, includingthe printed materials accompanying the SOFTWARE.2. DESCRIPTION OF OTHER RIGHTS AND LIMITATIONS (a) Limitations on Reverse Engineering, Decompilation and Disassembly - You maynot reverse engineer, decompile, or disassemble the SOFTWARE PRODUCT, exceptand only to the extent that such activity is expressly permitted by applicable law not-withstanding this limitation. You may not make any changes or modifications to theSoftware, without the written permission of an officer of DSC. You may not removeany proprietary notices, marks or labels from the Software Product. You shall institutereasonable measures to ensure compliance with the terms and conditions of this EULA.(b) Separation of Components - The SOFTWARE PRODUCT is licensed as a singleproduct. Its component parts may not be separated for use on more than one HARD-WARE unit.(c) Single INTEGRATED PRODUCT - If You acquired this SOFTWARE withHARDWARE, then the SOFTWARE PRODUCT is licensed with the HARDWARE asa single integrated product. In this case, the SOFTWARE PRODUCT may only be usedwith the HARDWARE as set forth in this EULA.(d) Rental - You may not rent, lease or lend the SOFTWARE PRODUCT. You maynot make it available to others or post it on a server or web site.(e) Software Product Transfer - You may transfer all of Your rights under this EULAonly as part of a permanent sale or transfer of the HARDWARE, provided You retain nocopies, You transfer all of the SOFTWARE PRODUCT (including all component parts,the media and printed materials, any upgrades and this EULA), and provided the recipi-ent agrees to the terms of this EULA. If the SOFTWARE PRODUCT is an upgrade, anytransfer must also include all prior versions of the SOFTWARE PRODUCT.(f) Termination - Without prejudice to any other rights, DSC may terminate thisEULA if You fail to comply with the terms and conditions of this EULA. In such event,You must destroy all copies of the SOFTWARE PRODUCT and all of its componentparts.(g) Trademarks - This EULA does not grant You any rights in connection with anytrademarks or service marks of DSC or its suppliers.3. COPYRIGHT - All title and intellectual property rights in and to the SOFTWARE PRODUCT (including but not limited to any images, photo-graphs, and text incorporated into the SOFTWARE PRODUCT), the accom-panying printed materials, and any copies of the SOFTWARE PRODUCT, are owned by DSC or its suppliers. You may not copy the printed materials accompanying the SOFTWARE PRODUCT. All title and intellectual prop-erty rights in and to the content which may be accessed through use of the SOFTWARE PRODUCT are the property of the respective content owner and may be protected by applicable copyright or other intellectual property laws and treaties. This EULA grants You no rights to use such content. All rights not expressly granted under this EULA are reserved by DSC and its suppliers.4. EXPORT RESTRICTIONS - You agree that You will not export or re-export theSOFTWARE PRODUCT to any country, person, or entity subject to Canadian exportrestrictions. 5. CHOICE OF LAW - This Software License Agreement is governed by the laws ofthe Province of Ontario, Canada.6. ARBITRATION - All disputes arising in connection with this Agreement shall bedetermined by final and binding arbitration in accordance with the Arbitration Act, andthe parties agree to be bound by the arbitrator’s decision. The place of arbitration shallbe Toronto, Canada, and the language of the arbitration shall be English.7. LIMITED WARRANTY(a) NO WARRANTY - DSC PROVIDES THE SOFTWARE “AS IS” WITHOUTWARRANTY. DSC DOES NOT WARRANT THAT THE SOFTWARE WILLMEET YOUR REQUIREMENTS OR THAT OPERATION OF THE SOFTWAREWILL BE UNINTERRUPTED OR ERROR-FREE.(b) CHANGES IN OPERATING ENVIRONMENT - DSC shall not be responsiblefor problems caused by changes in the operating characteristics of the HARDWARE, orfor problems in the interaction of the SOFTWARE PRODUCT with non-DSC-SOFT-WARE or HARDWARE PRODUCTS.(c) LIMITATION OF LIABILITY; WARRANTY REFLECTS ALLOCATION OFRISK - IN ANY EVENT, IF ANY STATUTE IMPLIES WARRANTIES OR CON-DITIONS NOT STATED IN THIS LICENSE AGREEMENT, DSC’S ENTIRE LIA-BILITY UNDER ANY PROVISION OF THIS LICENSE AGREEMENT SHALLBE LIMITED TO THE GREATER OF THE AMOUNT ACTUALLY PAID BYYOU TO LICENSE THE SOFTWARE PRODUCT AND FIVE CANADIAN DOL-LARS (CAD$5.00). BECAUSE SOME JURISDICTIONS DO NOT ALLOW THEEXCLUSION OR LIMITATION OF LIABILITY FOR CONSEQUENTIAL ORINCIDENTAL DAMAGES, THE ABOVE LIMITATION MAY NOT APPLY TOYOU.(d) DISCLAIMER OF WARRANTIES - THIS WARRANTY CONTAINS THEENTIRE WARRANTY AND SHALL BE IN LIEU OF ANY AND ALL OTHERWARRANTIES, WHETHER EXPRESSED OR IMPLIED (INCLUDING ALLIMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PAR-TICULAR PURPOSE) AND OF ALL OTHER OBLIGATIONS OR LIABILITIESON THE PART OF DSC. DSC MAKES NO OTHER WARRANTIES. DSC NEI-THER ASSUMES NOR AUTHORIZES ANY OTHER PERSON PURPORTING TOACT ON ITS BEHALF TO MODIFY OR TO CHANGE THIS WARRANTY, NORTO ASSUME FOR IT ANY OTHER WARRANTY OR LIABILITY CONCERNINGTHIS SOFTWARE PRODUCT.(e) EXCLUSIVE REMEDY AND LIMITATION OF WARRANTY - UNDER NOCIRCUMSTANCES SHALL DSC BE LIABLE FOR ANY SPECIAL, INCIDEN-TAL, CONSEQUENTIAL OR INDIRECT DAMAGES BASED UPON BREACHOF WARRANTY, BREACH OF CONTRACT, NEGLIGENCE, STRICT LIABIL-ITY, OR ANY OTHER LEGAL THEORY. SUCH DAMAGES INCLUDE, BUTARE NOT LIMITED TO, LOSS OF PROFITS, LOSS OF THE SOFTWARE PROD-UCT OR ANY ASSOCIATED EQUIPMENT, COST OF CAPITAL, COST OF SUB-STITUTE OR REPLACEMENT EQUIPMENT, FACILITIES OR SERVICES,DOWN TIME, PURCHASERS TIME, THE CLAIMS OF THIRD PARTIES,INCLUDING CUSTOMERS, AND INJURY TO PROPERTY. WARNING: DSC recommends that the entire system be completely tested on a regularbasis. However, despite frequent testing, and due to, but not limited to, crim-inal tampering or electrical disruption, it is possible for this SOFTWAREPRODUCT to fail to perform as expected.©2008 Digital Security Controls, Toronto, Canada • www.dsc.com Printed in Canada

Navigation menu