UBS Axcera CU150BTD 150-Watt UHF Digital Transmitter User Manual 5

UBS-Axcera 150-Watt UHF Digital Transmitter 5

User manual 5

Download: UBS Axcera CU150BTD 150-Watt UHF Digital Transmitter User Manual 5
Mirror Download [FCC.gov]UBS Axcera CU150BTD 150-Watt UHF Digital Transmitter User Manual 5
Document ID1145893
Application ID7jjGc1lbmAm/Akm11xi7cA==
Document DescriptionUser manual 5
Short Term ConfidentialNo
Permanent ConfidentialNo
SupercedeNo
Document TypeUser Manual
Display FormatAdobe Acrobat PDF - pdf
Filesize7.9kB (98737 bits)
Date Submitted2009-07-28 00:00:00
Date Available2009-07-29 00:00:00
Creation Date2009-07-10 16:13:41
Producing SoftwareAcrobat Distiller 6.0 (Windows)
Document Lastmod2009-07-10 16:13:41
Document TitleCU150BTD -- Compiled Interconnects & Datasheets.pdf
Document CreatorPScript5.dll Version 5.2
Document Author: twolak

User’s Manual
Manuel de l’utilisateur
Manual del usuario
A n tec Tru eP o w er U s er' s M an u al
Antec TruePower ATX12V power supply
Models: TRUE330, TRUE380, TRUE430, TRUE480, TRUE550
Table of Contents
Table des matières - Indice
English ................................................................. 1
Français ................................................................ 8
Español ................................................................. 16
Antec Low Noise Technology: The Antec TruePower power supply is equipped with
special circuitry to achieve optimum balance between noise reduction and necessary cooling.
Thanks to an advanced temperature response system the power supply fans run at the lowest
speed appropriate to load and conditions. The result is a great reduction in overall noise,
even in comparison to traditional thermally-controlled fans.
Your TruePower power supply can also monitor and control the system case fan speed.
There are two dedicated fan connectors marked Fan Only from the power supply for system
case fans. You may connect your case fans to them and have the TruePower circuitry
control the speed of the case fans.
Note: Please do not connect more than three external fans to the Fan Only connectors in
any combination. For maximum cooling you may choose to connect the case fans to the
regular 4-pin peripheral connectors, but in this fashion noise will not be reduced.
Connectors: The Antec TruePower power supply is an ATX12V form factor power
supply. An ATX12V power supply has a single 20-pin Main Power Connector, a 6-pin
AUX Power Connector and a 4-pin +12V Power Connector to the motherboard. It also
comes with seven 4-pin Peripheral Power Connectors and two 4-pin Floppy Drive Power
Connectors to your drives. It is backwards compatible to previous ATX form factor power
supplys. If your motherboard does not support the AUX Power Connector or the +12V
Power Connector, you can still use this power supply.
The TruePower power supply is also equipped with a 3-pin fan signal connector. Connect
it to one of the fan connectors on your motherboard. You may monitor the speed of the rear
power supply fan through your motherboard BIOS or through the monitoring software that
comes with your motherboard.
Note: The speed of the fan may be as low as 1500 RPM when temperatures are low. At
these speeds some motherboards may not be able to properly detect the fan speed and may
generate false warnings of fan failure. Please refer to your motherboard manual for proper
fan monitoring set up.
Power Switch: This power supply comes with a main power switch. Make sure you
turn the switch to the ON ( I ) position before you boot up your computer for the first time.
In normal operation there is no need to turn the switch to the OFF (O) position since the
power supply is equipped with a soft on/off feature which turns your computer on and off
through the soft switch on your computer case. You may need to turn the switch to the OFF
position occasionally should your computer crash and you cannot shut it down through use
of the soft switch.
[Applicable only to models designed for sale in the European Union: TruePower
models designed for the EU include Power Factor Correction (PFC) circuitry in accord
with European standard regulation code EN61000-3-2. By altering the input current wave
shape, PFC improves the power factor of the power supply and results in increased energy
efficiency, reduced heat loss, prolonged life for power distribution and consumption
equipment, and improved output voltage stability.]
Installation:
Note (not applicable to models designed for the European Union): Check the red
power supply voltage switch setting before installation. It should be the same as your local
power voltage (115V for North America, Japan, etc. and 230V for Europe and many other
countries). Change the voltage setting if necessary. Failure to take this precaution could
result in damage to your equipment and could void your warranty.
1.
2.
3.
4.
5.
6.
7.
8.
9.
Disconnect the power cord from your old power supply.
Follow your computer case manual and open the case.
Disconnect all the power Connectors from the motherboard and from the peripheral
devices such as case fans, hard drives, floppy drives, etc.
Remove the existing power supply from your computer case and replace it with
the Antec power supply.
Connect the Power Connectors to your motherboard and peripheral devices.
Connect the case fans to the dedicated fan connectors.
Note: Do not connect other devices except fans to these connectors. You may
connect case fans to the regular 4-pin Peripheral connectors if you choose not to
utilize TruePower Circuitry on your case fans.
Connect the 3-pin fan signal connector to one of the fan connectors on your
motherboard.
Note: You do not need to connect the 3-pin fan signal connector in order to make
the power supply work if you choose not to monitor the speed of the fan.
Close the computer case.
Connect the power cord to the Antec power supply
Specifications:
1.0 INPUT:
1.1. VOLTAGE
RANGE MINIMUM NOMINAL MAXIMUM UNITS
90
115
135
VRMS
180
230
265
VRMS
1.2 FREQUENCY
47Hz ~ 63Hz
1.3 CURRENT
TRUE330
TRUE380
TRUE430
TRUE480
TRUE550
115V 230V
7A
4A
8A
5A
9A
5A
12A 6A
12A 6A
1.4 INRUSH CURRENT
115V/50A(max.), 230V/80A(max.) at 25°C cold start
1.5 POWER EFFICIENCY
68% (min.) at full load, 115/230Vac 60Hz/50Hz
2.0 OUTPUT:
VOLTAGE
MAX. LOAD
TRUE330
TRUE380
TRUE430
TRUE480
TRUE550
MIN. LOAD
REGULATION
RIPPLE & NOISE
(mV)
+5V +12V +3.3V -5V
-12V +5VSB
30A
35A
36A
38A
40A
0A
±3%
50
1.0A 2.0A
1.0A 2.0A
1.0A 2.0A
1.0A 2.0A
1.0A 2.0A
0A
0A
±5% ±5%
120
50
17A 28A 0.5A
18A 28A 0.5A
20A 28A 0.5A
22A 30A 1.5A
24A 32A 0.5A
0.8A 0A 0A
±3% ±3% ±5%
120 50
50
Note:
1) The continuous maximum total output power
TRUE330
TRUE380
TRUE430
TRUE480
TRUE550
TOTAL MAX.
OUTPUT
330W
380W
430W
480W
550W
+5V,+12V & +3.3V
MAX. OUTPUT
310W
360W
410W
460W
530W
2) Peak surge current: 15 sec max.
Measurements shall be made with an oscilloscope with 20MHz bandwidth. 10uF elec
trolytic capacitor parallel 0.1uF ceramic capacitor to simulate system loading to measure
it.
Figure 1.
AC-V
3) At peak load +12V output regulation +/-10%.
2.1 HOLD-UP TIME: 20ms (minimum)
Test Condition: Full load. AC input 115V or 230V, 60Hz or 50Hz
2.2 LOAD TRANSIENT RESPONSE (STEP LOAD)
Step load changes up to 20% of full load, while other loads remains constant within the
rating. The load waveform shall be a square wave with the slope of the rise and fall at
0.1A/usec and the frequency shall be from 10Hz to 1 kHz. The DC output voltage will
stay within regulation during the step load changes.
AC-ON
AC-OFF
HIGH
HIGH
LOW
PS-ON
VB= 4.75V
2.3 OVERSHOOT
Overshoot at turn on or turn off shall be less than 10% of the nominal output voltage.
+5V Wave Form
T2
P.G. WAVE FORM
3.0 PROTECTION:
If the power supply latches into shutdown stage (when over current, over voltage or
short circuit protection is working), the power supply shall return to normal operation
only after the fault has been removed and PS-ON is reset for a minimum of 1 Second
or remove AC power is removed and re-applied.
T4
T1
POWER FAIL
TURN-ON
T3
ON-RING
OFF-RING
T5
HOLD-UP
POWER GOOD
3.1 OVER CURRENT PROTECTION
Overload currents applied to each tested output rail will cause output trip before they
reach or exceed 110% ~ 150% for testing purposes. Overload currents should be ramped
at a minimum rate of 10 A/s starting from full load.
4.1 REMOTE ON/OFF CONTROL
The power supply is turned on or off by TTL signal.
3.2 OVER VOLTAGE PROTECTION
Remote On/Off Signal Characteristics
Active low
Active high
Power supply turn on
Power supply turn off
PS-ON
MIN MAX
Vil, input low voltage
0.8V
Vil, input low current, Vin=0.4V
-1.6mA
Vih, input High voltage, lin=-200uA 2.0V
Vih open circuit, lin=0
5.25
SENSE LEVEL OVER VOLTAGE
+5V
6.5V/max.
+12V
15.6V/max.
+3.3V
4.1V/max.
3.3 SHORT CIRCUIT PROTECTION
All output to GND.
4.0 TIME SEQUENCE:
T1 Turn On Time (500ms max.)
T2 Output Voltage Sequencing (20ms max.)
T3 Power Good Delay Time (100ms < t3 <500ms)
T4 Power Fail Delay Time (1ms min.)
T5 Power Good Hold-Up time (20ms min)
115V/230V(FULL LOAD): 1ms minimum
4.2 AUXILIARY +5VSB
This power supply is specifically equipped with an independent stand-by +5V output
current, 2.0A max. This output will always provide +5V except when the AC line is
cut-off.
4.3 AUTO RESTART
If the output of the power supply drops out of the regulation caused by AC line Voltage,
the power supply will automatically resumes normal operation only after the AC line
voltage returns to the specified operating range.
5.0 ENVIRONMENT:
Ambient operation temperature
Ambient operation relative humidity
Ambient storage temperature
Ambient storage relative humidity
10°C to +50°C
20% to 85%
-40°C to +70°C
10% to 95%
AUXILIARY POWER CONNECTOR (PS1)
6.0 CE REQUIREMENTS:
6.1 EMI
1. MEET FCC CLASS B
2. MEET EN55022 CLASS B
HOUSING: WST P/N P20-I42002 or equivalent
TERMINAL: WST P/N I42002BS-2 or equivalent
Pin
6.2 ESD
MEET IEC-801-2/8KV
6.3 EFT/BURST
MEET IEC-801-4/2KV
6.4 SAFETY REQUIREMENTS
1. MEET UL 1950
2. MEET IEC 60950
HOUSING: MOLEX 39-01-2040 or equivalent.
TERMINAL: MOLEX 39-29-9042 or equivalent.
Pin
8.0 DC CONNECTOR AND CASE REQUIREMENTS
ATX MAIN CONNECTOR (P1)
HOUSING: P/N P20-I42002 or equivalent.
TERMINAL: P/N I42002BS-2 or equivalent.
Pin Pin Signal
11 1
+3.3VDC
11
16AWG (Wire)
Orange
12
13
14
15
16
17
18
19
20
Orange
Black
Red
Black
Red
Black
Gray (18AWG)
Purple (18AWG)
Yellow
10
PERIPHERAL POWER CONNECTOR
(P2, P4, P6, P7, P8, P9, P10)
HOUSING: JMT JP1120-4
HOUSING: WST P4-A10202 OR EQU
TERMINAL: JMT J1120BS-2
TERMINAL: WST A10209BS-2
Pin
Signal
+12VDC
COM
COM
+5VDC
16AWG (Wire)
Black
Black
Black
Orange
Orange
Red
+12V CONNECTOR
7.0 MTBF
80,000 hours at 25°C (demonstrated)
16AWG (Wire)
Signal
Orange (16AWG) +3.3VDC
Brown (22AwG) +3.3V
default sense
Blue (18AWG)
-12VDC
Black
COM
Green (18AWG) PS-ON
Black
COM
Black
COM
Black
COM
White (18AWG) -5V
Red
+5VDC
Red
+5VDC
Signal
COM
COM
COM
+3.3VDC
+3.3VDC
+5VDC
18AWG (Wire)
Yellow
Black
Black
Red
+3.3VDC
COM
+5VDC
COM
+5VDC
COM
POK
+5VSB
+12VDC
Signal
COM
COM
+12VDC
+12VDC
20AWG (Wire)
Black
Black
Yellow
Yellow
FAN SPEED MONITORING CONNECTOR
Pin
Signal
24AWG (Wire)
SENSOR Blue
NONE
COM
Black
FAN ONLY CONNECTOR
Pin
Signal
18AWG (Wire)
+12VDC Yellow
COM
Black
NO PIN
NO PIN
FLOPPY DRIVE POWER CONNECTOR
(P3, P5)
HOUSING: JMT JP11635-4
HOUSING: WST P4-I25001 OR EQU
TERMINAL: JMT J11635BS-2
TERMINAL: WST I25001BS-2 OR EQU
Pin Signal
22AWG (Wire)
1 +5VDC Red
2 COM
Black
3 COM
Black
4 +12VDC Yellow

Source Exif Data:
File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.4
Linearized                      : No
Page Count                      : 5
XMP Toolkit                     : XMP toolkit 2.9.1-13, framework 1.6
About                           : uuid:f3ab5049-da5a-41cb-8379-f3c4f19b6619
Producer                        : Acrobat Distiller 6.0 (Windows)
Create Date                     : 2009:07:10 16:13:41-04:00
Creator Tool                    : PScript5.dll Version 5.2
Modify Date                     : 2009:07:10 16:13:41-04:00
Document ID                     : uuid:76a28d9e-bc29-46d5-969f-e7824817f46f
Format                          : application/pdf
Title                           : CU150BTD -- Compiled Interconnects & Datasheets.pdf
Creator                         : twolak
Author                          : twolak
EXIF Metadata provided by EXIF.tools
FCC ID Filing: OUSCU150BTD

Navigation menu