UNION COMMUNITY AC-5000RF Access Controller User Manual AC5000 UserGuide 1 00

UNION COMMUNITY Access Controller AC5000 UserGuide 1 00

Users Manual

AC-5000 User Guide                                                                                                                                                   2 UNIONCOMMUNITY Co., Ltd. / 3F Hyundai Topics Bldg. 44-3 Bangi-dong Songpa-gu, Seoul, Korea (138-050) Tel : 02-6488-3000 , Fax : 02-6488-3099, E-Mail :sales@unioncomm.co.kr http://www.unioncomm.co.kr  <Revison History>    Version  Date  Description  Firmware Version 1.00  2011-01-10  Initial Release  10.51.00-000.00             <Glossary>   Admin (Administrator) - As  a  user  who  can  enter  the  terminal  menu  mode,  he/she  is  authorized  to register/modify/delete  terminal  users  and  change  the  operating  environment  by changing the settings. - If  there  is  no  administrator  registered  for  a  terminal,  anyone  can  enter  the  terminal menu and change the settings. Therefore, it  is recommended to register at least one administrator. - Special care is required for registration and operation as an administrator has the right to change important environment settings of the fingerprint recognizing unit.   1:1 Authentication (1 to 1, Verification) - This is a method that authenticates fingerprint with user ID or card entered - This method is called 1:1 authentication as only the fingerprint registered in the user ID or card is used for comparison.   1:N Authentication (1 to N, Identification)   - This is a method that searches a corresponding user only with fingerprint. - This method is called 1:N authentication as it searches the identical fingerprint from the registered fingerprints without user ID or card entered.   Security Level - This is the level used for fingerprint authentication displayed from 1 to 9 depending on how both fingerprints match against each other. Authentication will be successful only when the identity between both fingerprints is higher than the preset level. - The higher the authentication level, the higher the security. Nevertheless, as it requires a relatively high match rate, self-authentication is prone to failure. - 1:1 Level: Authentication level used for 1:1 verification. - 1:N Level: Authentication level used for 1:N identification.   Authentication Method - This represents the  various types of  authentication methods  including  FP  (fingerprint) authentication, RF (card) authentication, a combination of these methods. Ex) Card or FP: Authentication with card or fingerprint   Function Keys - [F1], [F2], [F3], [F4], and [ENT] keys are available. These keys allow a user to enter the menus or change modes such as office start/leave.
AC-5000 User Guide                                                                                                                                                   3 UNIONCOMMUNITY Co., Ltd. / 3F Hyundai Topics Bldg. 44-3 Bangi-dong Songpa-gu, Seoul, Korea (138-050) Tel : 02-6488-3000 , Fax : 02-6488-3099, E-Mail :sales@unioncomm.co.kr http://www.unioncomm.co.kr  LFD (Live Finger Detection) - This  function  allows  the  input  of  only  real  fingerprints  and  blocks  the  input  of  imitation fingerprints produced using rubber, paper, film, and silicone.
AC-5000 User Guide                                                                                                                                                   4 UNIONCOMMUNITY Co., Ltd. / 3F Hyundai Topics Bldg. 44-3 Bangi-dong Songpa-gu, Seoul, Korea (138-050) Tel : 02-6488-3000 , Fax : 02-6488-3099, E-Mail :sales@unioncomm.co.kr http://www.unioncomm.co.kr  Table of Contents <Revison History>.................................................................................................... 2 <Glossary>................................................................................................................ 2 Table of Contents .....................................오류!  책갈피가 정의되어 있지 않습니다. 1. Before use.............................................................................................................6 1.1. Safety precautions ......................................................................................6 1.2. Terminal description ................................................................................... 7 1.3. Screen description (during operation) ...................................................... 7 1.3.1. Icon shown during operation................................................................. 8 1.3.2. Message shown during operation......................................................... 8 1.4. LED signal shown during operation ........................................................ 11 1.5. Keys used during operation ..................................................................... 11 1.6. Voices used during operation ..................................................................12 1.7. Buzzer sounds used during operation .................................................... 12 1.8. How to register and input fingerprint ...................................................... 12 2. Product introduction..........................................................................................14 2.1. Features .....................................................................................................14 2.2. Configuration.............................................................................................16 2.2.1. Standalone (Access)...........................................................................16 2.2.2. Connect with PC SERVER (Access, Time & Attendance, Cafeteria)........... 16 2.3. Specification .............................................................................................. 17 3. Environment settings......................................................................................... 19 3.1. Items to be checked before environment settings ................................. 19 3.1.1. Entering menu .................................................................................... 19 3.1.2. How to access the menu without administrator verification ................ 19 3.1.3. Change settings.................................................................................. 20 3.1.4. Save environment settings ................................................................. 21 3.2. Menu Configuration...................................................................................23 3.3. User ............................................................................................................ 25 3.3.1. Add ..................................................................................................... 25 3.3.2. Delete .................................................................................................30 3.3.3. Modify.................................................................................................31 3.3.4. Delete All ............................................................................................ 32 3.4. Network ...................................................................................................... 32 3.4.1. IP ........................................................................................................32 3.4.2. Server IP.............................................................................................33 3.4.3. Terminal ID ......................................................................................... 33 3.5. Application .................................................................................................34 3.5.1. Application .......................................................................................... 34 3.5.2. Time Schedule....................................................................................35 3.5.3. Function Key.......................................................................................36 3.5.4. Extended Key ..................................................................................... 36 3.5.5. Display................................................................................................37 3.6. System........................................................................................................38 3.6.1. System Setting ...................................................................................38 3.6.2. Authentication ..................................................................................... 39 3.6.3. Fingerprint .......................................................................................... 40
AC-5000 User Guide                                                                                                                                                   5 UNIONCOMMUNITY Co., Ltd. / 3F Hyundai Topics Bldg. 44-3 Bangi-dong Songpa-gu, Seoul, Korea (138-050) Tel : 02-6488-3000 , Fax : 02-6488-3099, E-Mail :sales@unioncomm.co.kr http://www.unioncomm.co.kr 3.6.4. Language............................................................................................41 3.6.5. Data Time ...........................................................................................41 3.6.6. Database ............................................................................................42 3.7. Terminal...................................................................................................... 44 3.7.1. Terminal Option ..................................................................................44 3.7.2. Volume Control...................................................................................45 3.7.3. Door....................................................................................................46 3.7.4. Wiegand .............................................................................................47 3.7.5. Card Reader ....................................................................................... 47 3.7.6. External Device ..................................................................................49 3.8. Information................................................................................................. 49 3.8.1. System Info.........................................................................................49 3.8.2. Network Info ....................................................................................... 50 3.8.3. Database Info .....................................................................................50 3.8.4. View Log.............................................................................................50 3.8.5. Version Info......................................................................................... 51 3.9. Downloading user’s file ............................................................................51 3.9.1. Change background image.................................................................51 3.9.2. Change voice message ......................................................................52 3.9.3. Change user text ................................................................................ 52 4. How to use the terminal .....................................................................................54 4.1. Change authentication mode ................................................................... 54 4.2. ID input ....................................................................................................... 54 4.3. Authentication ...........................................................................................55 4.3.1. Fingerprint authentication ................................................................... 55 4.3.2. Card authentication ............................................................................55 4.3.3. Password authentication.....................................................................55
AC-5000 User Guide                                                                                                                                                   6 UNIONCOMMUNITY Co., Ltd. / 3F Hyundai Topics Bldg. 44-3 Bangi-dong Songpa-gu, Seoul, Korea (138-050) Tel : 02-6488-3000 , Fax : 02-6488-3099, E-Mail :sales@unioncomm.co.kr http://www.unioncomm.co.kr  1. Before use  1.1. Safety precautions    Warning Do  not  handle the unit  with wet hands and do not allow liquid to flow into it. ->  It  may  cause  an electric shock or damage.  Do not place a fire source near the unit.   -> It may cause a fire.   Do not disassemble, repair, or modify the unit.   ->  It  may  cause  an  electric shock, fire or damage.    Keep out of children’s reach.   ->  It  may  cause  an accident or damage.   - If the above warnings are ignored, it may result in death or serious injury.      Cautions Keep away from direct sunlight   ->  It  may  cause  mal-function,  deformation  or color change of the unit.   Avoid high humidity or dust   ->It may cause the unit to malfunction.    Avoid using water, benzene, thinner, or alcohol for cleaning the unit. ->  It  may  cause  an  electric shock or fire.    Do not place a magnet near the unit.   ->  The  unit  may  break down or malfunction.  Avoid getting the fingerprint input area dirty. ->It  may  prevent  the  unit from  recognizing  the fingerprint.   Avoid using insecticides or flammable sprays near the unit.   ->  It  may  result  in  the deformation  or  color change of the unit.    Avoid impact or using sharp objects on the unit.   ->  The  unit  may  be damaged and broken.    Avoid installing the unit in a  place  where temperature  severely changes. -> It  may  cause  the  unit  to malfunction.     - If the above cautions are ignored, it may result in property loss or human injury.   Under  no  circumstances  will  Union  Community  be  responsible  for  the  accidents  or  damages caused by inappropriate use of the product and neglect of the precautions stated in the user guide.
AC-5000 User Guide                                                                                                                                                   7 UNIONCOMMUNITY Co., Ltd. / 3F Hyundai Topics Bldg. 44-3 Bangi-dong Songpa-gu, Seoul, Korea (138-050) Tel : 02-6488-3000 , Fax : 02-6488-3099, E-Mail :sales@unioncomm.co.kr http://www.unioncomm.co.kr 1.2. Terminal description    1.3. Screen description (during operation)     LCD   Fingerprint Sensor Touch Key Normally, the figure is invisible as LED is off, but LED is on and the figure is shown when the user touches this area lightly.   Card Input Area   State Display LED  Connection with Server ④ Access Mode   Current Time  Door State③  Warning of Terminal Disassembly, etc②.  Fire Detection ①
AC-5000 User Guide                                                                                                                                                   8 UNIONCOMMUNITY Co., Ltd. / 3F Hyundai Topics Bldg. 44-3 Bangi-dong Songpa-gu, Seoul, Korea (138-050) Tel : 02-6488-3000 , Fax : 02-6488-3099, E-Mail :sales@unioncomm.co.kr http://www.unioncomm.co.kr 1.3.1. Icon shown during operation  None : Normal   Fire Detection  :  State  that  fire  is  detected  by  fire  sensor  (subject  to  the connection with fire sensor) None : Normal   Warning  : Abnormal state that terminal is disassembled or door has encountered a problem  : Door status is unknown  : Door is closed   Door status  : Door is opened None : LAN cable is not connected  : LAN cable is connected, but not yet to the server     Connection  of Server  : Connected with the server program   1.3.2. Message shown during operation   - Initial screen of AC5000  - When authentication is successful  - When authentication is failed
AC-5000 User Guide                                                                                                                                                   9 UNIONCOMMUNITY Co., Ltd. / 3F Hyundai Topics Bldg. 44-3 Bangi-dong Songpa-gu, Seoul, Korea (138-050) Tel : 02-6488-3000 , Fax : 02-6488-3099, E-Mail :sales@unioncomm.co.kr http://www.unioncomm.co.kr  - When any unregistered user ID is input - When fingerprint authentication is attempted in the event where the server is not connected and there is no registered fingerprint in the terminal  - When any unregistered card is input  - When fingerprint input is failed -  When  the  user  took  the  finger  off  too  fast  before  the fingerprint is input  - When Anti-pass back is in error (in the event the user uses the anti-pass back function)  - When the user attempted two or more times at the same meal time zone (in the event it is used for cafeteria)  -  When  there  is  no  response  from  the  server  during  the attempt of authentication to the server -  When  network  is  disconnected  during  the  attempt  of authentication to the server  - When the user is not authorized for authentication even if he/she  is  being  registered  or  the  user  attempted authentication when access is not allowed
AC-5000 User Guide                                                                                                                                                   10 UNIONCOMMUNITY Co., Ltd. / 3F Hyundai Topics Bldg. 44-3 Bangi-dong Songpa-gu, Seoul, Korea (138-050) Tel : 02-6488-3000 , Fax : 02-6488-3099, E-Mail :sales@unioncomm.co.kr http://www.unioncomm.co.kr  - When the terminal is set to Locked  -  When  it  is  not  the  meal  time  (in  the  event  it  is  set  to Cafeteria)  -  When  the  authentication may  not  be  treated  as  there  are too  many  authentication  requests  from  the  terminal  during the server authentication.  - During the status that is waiting for the user ID input  -  During  the  status  that  is  waiting for  the  password  input  of the user  - During the status that is waiting for the fingerprint input of the user  -  During  the  status  that  is  waiting  for  the  card  input  of  the user
AC-5000 User Guide                                                                                                                                                   11 UNIONCOMMUNITY Co., Ltd. / 3F Hyundai Topics Bldg. 44-3 Bangi-dong Songpa-gu, Seoul, Korea (138-050) Tel : 02-6488-3000 , Fax : 02-6488-3099, E-Mail :sales@unioncomm.co.kr http://www.unioncomm.co.kr  -  At  the  time of  fingerprint  card  authentication, it shows the status that the card reads fingerprint data. The user must put  the  card  for  1~2  seconds  until  the  message disappears.  -  When  waiting  for  the  response  after  the  user  attempted authentication to the server  - When upgrading the terminal program (Be sure not to power off the terminal during the time the message is output)   1.4. LED signal shown during operation  ● Power Red On: Normal Flickering:  When  the  lid  is  opened  or  there  is  any communication error in the connection with LC010 ● Door  Green On : Door Open Off: Door Close   1.5. Keys used during operation  [0]~[9]  - Keys used for numeric input [F1]~[F3]  - Keys used for changing the authentication mode [F4] or [←] - Used for changing the authentication mode - Used as Delete key for correction when inputting the figure - Used for canceling input and moving to the parent menu in the menu mode [F4(←)~] - Means pressing [F4(←)] key for 2 seconds or longer -  When input focus  is  located  in  the  input  box,  it  can  cancel  the input and exit to the parent menu by pressing this button for 2 seconds or longer
AC-5000 User Guide                                                                                                                                                   12 UNIONCOMMUNITY Co., Ltd. / 3F Hyundai Topics Bldg. 44-3 Bangi-dong Songpa-gu, Seoul, Korea (138-050) Tel : 02-6488-3000 , Fax : 02-6488-3099, E-Mail :sales@unioncomm.co.kr http://www.unioncomm.co.kr ENT [or MENU] - Used for modifying the mode -  Used  for  saving  the  value  set  in  the  menu  mode  or  moving  to  the configuration in the screen [ENT~] - Means pressing [ENT] key for 2 seconds or longer   - Used for accessing the menu when pressed on the basic screen - When input focus is located in the input box, the user can exit to the parent  menu  with  the  current input  value  saved  by  pressing  it  for  2 seconds or longer -  Used  to  apply  the  configuration  to  the  current  screen  in  the  menu mode and then exit to the parent menu.   1.6. Voices used during operation  Type of operation  Voice For fingerprint input  Please enter your fingerprint. When  authentication is successful  You are authorized. When  authentication is failed  Please try again.   1.7. Buzzer sounds used during operation  Beep Sound  that  is generated when  a  key  is pressed  or  a card  is  being manipulated When the key is pressed or card is read; When  fingerprint  input  is  completed  and  the  user  may take finger off Be peep  Sound  of failure When  authentication  is  failed  or  when  the  user’s fingerprint is wrongly input Brrrrrrp  When  standing by for input When notifying  the status of waiting for the user’s input of fingerprint or password Beeeep  Success  When  succeeding  in  authentication  or  completing  the setting work   1.8. How to register and input fingerprint    How to input fingerprint  Please input your fingerprint as if you are sealing a document using your forefinger. Avoid  inputting  fingerprint  with  the  fingertip  touched  lightly  in  the  event  of input/registration. Be sure that the center of fingerprint correctly touches the fingerprint input area.
AC-5000 User Guide                                                                                                                                                   13 UNIONCOMMUNITY Co., Ltd. / 3F Hyundai Topics Bldg. 44-3 Bangi-dong Songpa-gu, Seoul, Korea (138-050) Tel : 02-6488-3000 , Fax : 02-6488-3099, E-Mail :sales@unioncomm.co.kr http://www.unioncomm.co.kr      Input the fingerprint of your forefinger if possible.  It will facilitate the accurate and stable input of fingerprint.     Please check if the fingerprint is not clear or has any scar. Too dry or wet fingerprint, ambiguous fingerprint, fingerprint with scar, etc. may not be recognized. In this case, use/register the fingerprint of another finger.       Precautions related with the user’s fingerprint status  Depending  on  the  fingerprint  status,  the  user  may  not  use  fingerprint  or  suffer inconvenience from its use.    This product is the fingerprint recognizing system. Any fingerprint that is damaged or  thin  may  not  be  used.  In  such  case,  the  user  is  required  to  operate  with password.    When the finger is in a dry condition, the user is advised to breathe lightly on the finger for a smooth operation.    In  case  of  a  child,  due to  small  size or  tender  property  of  fingerprint,  it  may  be difficult or impossible to use it. Therefore, it is necessary to register the fingerprint every 6 months interval.    In  case  of  old  people,  excessive  tiny  lines  that  exist  on  the  fingerprint  to  be registered may prevent proper registration.    It is recommended to register at least 2 fingerprints of the user if possible.
AC-5000 User Guide                                                                                                                                                   14 UNIONCOMMUNITY Co., Ltd. / 3F Hyundai Topics Bldg. 44-3 Bangi-dong Songpa-gu, Seoul, Korea (138-050) Tel : 02-6488-3000 , Fax : 02-6488-3099, E-Mail :sales@unioncomm.co.kr http://www.unioncomm.co.kr  2. Product introduction   2.1. Features   Application of POE and Terminal Block – Easy to install       - As it supports POE, it can be installed with LAN cable without a separate power cable.     Designed in IP65 rainproof specification – Outdoor installation is possible.   Slim and polished design             -  Easy  to  install  as  it  is  designed  in  a  standing  type;  Slim  and  elegant  design using Color LCD and Touch Key   Download function of Server – Enables to change background image and voice -  Provides  a  variety  of  info  messages  through  color  LCD  and  voice;  User  can download  background  image  and  voice  from  the  server  according  to  his/her preference.  Especially,  the  built-in  LCD  Backlight  and  Touch  key  LED  enable identifying the screen and manipulating the keys in a dark place.   Convenient Auto Sensing Function -  Enables to easily perform the operation of authentication by inputting the fingerprint without entering the key separately   Easy self-authentication through fingerprint -  Prevents  the  risk  of forgetting the  password,  loss/theft of  card  or key  by  adopting fingerprint recognition technology that is biometrics; reinforces the security of self-authentication through the use of own fingerprint   Access Management System using the network (LAN) -  Communication  is  carried  out  between  fingerprint  recognition  device  and authentication server using TCP/IP protocol; Allows for easy expansion as it can be applied  to  the  network  as  it  is.  10/100  Mbps  Auto  Detect  ensures  high-speed operation; Enables easy management and monitoring through the network   Provides a diverse and flexible access management -  Provides a perfect control function by granting the right to entrance/access by user group   Applicable  for  various  operation  methods  such  as  access,  time  &  attendance, cafeteria, etc. -  Enables  a  variety  of  operation  methods  depending  on  the  settings  of  operating method in the terminal menu   Abundant capacity for treatment of the server -  In the event of managing the persons who enter using the server, it allows to treat almost an unlimited number of persons.   Provides a variety of registration and authentication methods There are 12 registration and authentication methods for a general user. Therefore, it is  necessary  to  determine  such  registration  and  authentication  method  before
AC-5000 User Guide                                                                                                                                                   15 UNIONCOMMUNITY Co., Ltd. / 3F Hyundai Topics Bldg. 44-3 Bangi-dong Songpa-gu, Seoul, Korea (138-050) Tel : 02-6488-3000 , Fax : 02-6488-3099, E-Mail :sales@unioncomm.co.kr http://www.unioncomm.co.kr registering a user or administrator. FP  Fingerprint registration Fingerprint Authentication PW  Card registration Card authentication FP or PW  Fingerprint and password registration Password authentication when fingerprint authentication is failed FP & PW  Fingerprint and password registration   Fingerprint authentication and then password authentication Card  Card registration Card authentication   Card or FP  Card and fingerprint registration Card or fingerprint authentication Card & FP  Card and fingerprint registration Card authentication and then fingerprint authentication Card or PW  Card and password registration Card or password authentication Card and PW  Card and password registration Card authentication and then password authentication (ID  or  Card)  & FP Card and fingerprint registration ID input and then fingerprint authentication, or card authentication and then fingerprint authentication (ID  or  Card)  & PW Card and password registration ID input and then password authentication, or card authentication and then password authentication Card  &  PW  & FP Card, password, and fingerprint registration Card authentication and then fingerprint & password authentication
AC-5000 User Guide                                                                                                                                                   16 UNIONCOMMUNITY Co., Ltd. / 3F Hyundai Topics Bldg. 44-3 Bangi-dong Songpa-gu, Seoul, Korea (138-050) Tel : 02-6488-3000 , Fax : 02-6488-3099, E-Mail :sales@unioncomm.co.kr http://www.unioncomm.co.kr  2.2. Configuration  2.2.1. Standalone (Access)               2.2.2. Connect with PC SERVER (Access, Time & Attendance, Cafeteria)                                             TCP/IP  Cafeteria management program    Time & attendance management program Internet / WAN / LAN TCP/IP  Fingerprint  authentication server (Fixed IP) UDB Server Database (MDB or MSSQL) TCP/IP Remote Admin Program (User  and  terminal  setting management)  TCP/IP TCP/IP TCP/IP DC12V Adapter Electromagnetic Lock   (Lock+, Lock-, Monitor)
AC-5000 User Guide                                                                                                                                                   17 UNIONCOMMUNITY Co., Ltd. / 3F Hyundai Topics Bldg. 44-3 Bangi-dong Songpa-gu, Seoul, Korea (138-050) Tel : 02-6488-3000 , Fax : 02-6488-3099, E-Mail :sales@unioncomm.co.kr http://www.unioncomm.co.kr  2.3. Specification  Division  SPEC  REMARK CPU  32Bit RISC CPU (400MHz)   Rainproof  IP65   LCD  2.8” TFT Color (320*240)   Touch Key  15key (0~9, F1~F4, Enter)   32M SDRAM   MEMORY 32M FLASH 20,016 User 20,016 Finger 61,439 Log Fingerprint sensor  Optical   Authentication speed  Within 1 second   Scan Area / Resolution  15 * 17mm / 500 DPI   FRR / FAR  0.1% / 0.001%   Temperature / Humidity -20 ~ 50 / Lower than 90% RH   POE  Supports 13W POE   INPUT : Universal AC 100 ~ 250V   OUTPUT : DC 12V (Option : DC 24V)   AC / DC Adapter UL, CSA, CE Approved   Lock Control  EM, Strike, Motor Lock, Auto Door   I/O  3 In (1 Exit, 2 Monitor) 2 Out (Lock Control)   TCP/IP (10/100Mbps) Authentication server communication RS-232  Meal ticket printer RS-485  External device communication Communication Port Wiegand In/Out Card reader or External device communication Card Reader 125KHz RF or 13.56MHz Smart (1 SAM Socket) Option SIZE  88.0mm * 175.0mm * 43.4mm
AC-5000 User Guide                                                                                                                                                   18 UNIONCOMMUNITY Co., Ltd. / 3F Hyundai Topics Bldg. 44-3 Bangi-dong Songpa-gu, Seoul, Korea (138-050) Tel : 02-6488-3000 , Fax : 02-6488-3099, E-Mail :sales@unioncomm.co.kr http://www.unioncomm.co.kr
AC-5000 User Guide                                                                                                                                                   19 UNIONCOMMUNITY Co., Ltd. / 3F Hyundai Topics Bldg. 44-3 Bangi-dong Songpa-gu, Seoul, Korea (138-050) Tel : 02-6488-3000 , Fax : 02-6488-3099, E-Mail :sales@unioncomm.co.kr http://www.unioncomm.co.kr  3. Environment settings  3.1. Items to be checked before environment settings  3.1.1. Enter the Menu  Press  [ENT]  key  for  two  seconds  or  longer,  then  the  user  can  access  the  screen  for menu selection as follow;  <Figure 3-1>  User can transfer to each sub menu and have access by pressing the relevant number key. If the admin is already registered, the Verify Admin screen appears as below;  <Figure 3-2>  In  compliance  with  the  registered  authentication  method  such  as  card,  fingerprint  or password,  user  can  access  each  menu  subject  to  successful  identification  after  the verification of admin is finished.    Verify  Admin  appears  only  when  there  is  a  registered  admin. When  accessing  the menu mode, once being identified, the user is allowed to access all the menus until the user completely exits from the main menu.   3.1.2. How to access the menu without the verification of admin  This is the way of  accessing the menu used inevitably when fingerprint authentication is impossible because the user forgot the admin password or lost the card registered on the terminal, or there is no admin.
AC-5000 User Guide                                                                                                                                                   20 UNIONCOMMUNITY Co., Ltd. / 3F Hyundai Topics Bldg. 44-3 Bangi-dong Songpa-gu, Seoul, Korea (138-050) Tel : 02-6488-3000 , Fax : 02-6488-3099, E-Mail :sales@unioncomm.co.kr http://www.unioncomm.co.kr   Remove the bracket at the backside of the terminal to open the lid.    With the lid open, as shown in the figure below, connect pin No. 1 with pin No. 3, and pin No. 2 with pin No. 4 of J404 connector respectively at backside.  <Figure 3-3>     Access the menu by pressing [F4(←)]key for 2 seconds or longer, fill Admin ID with ‘0’ on Verify Admin screen in <Figure 3-2>, and then press [ENT]key. The user can then access the menu selected with the buzzer sounding “Brrrrrrp” .    After  modifying  the  configuration,  don’t  fail  to  get  rid  of  the  connected  pin  of  J404 connector.     3.1.3. Modify setvalue  The following are the name and input method by input items.  <Figure 3-4>       Input Box In case of an item where the value is directly input like ‘1:1 Level’, user must delete the  existing  value  with  [F4(←)]  key  when  the  focus  is  in  the  applicable  item  and Input Box (with input focus)①  ①Input Box (without input focus) Select Button② Check Box③
AC-5000 User Guide                                                                                                                                                   21 UNIONCOMMUNITY Co., Ltd. / 3F Hyundai Topics Bldg. 44-3 Bangi-dong Songpa-gu, Seoul, Korea (138-050) Tel : 02-6488-3000 , Fax : 02-6488-3099, E-Mail :sales@unioncomm.co.kr http://www.unioncomm.co.kr then input the new value using [0]~[9] key.      Select Button In case of selecting an item out of the given sample like ‘Fake Finger Detect’, user must modify the item selection ( ) by pressing the relevant number key, provided that, user must select the item after moving the focus from the input box by pressing [ENT] key if the focus is located at the input box as shown in <Figure 3-5>.  <Figure 3-5> Move Focus (using [ENT] key)      As shown in the figure at the left, the letter is displayed in a reverse type when the focus  is  located  at  input  box.  As  shown  in  the  figure  at  the  right,  the  applicable letters are displayed in black instead of grey when the focus moved to ‘Fake Finger Detect’     Check Box   In  case  the  user  must  select  whether  or  not  checking  like  ‘Check  SameFP’,  the user can either select ( ) or release ( ) by pressing the relevant key [5]. If it is impossible to select the relevant item, it is displayed in ( )  Press [F4(←)] key to cancel in the course of setting and move to the parent menu. When the focus is located at the input box, [F4(←)] key functions as [DEL] key that   deletes the figures one by one. In this case, press [F4(←)] key for two seconds or   longer to cancel input and exit to the parent menu.    Press [ENT] key for two seconds   or longer to save the current configuration and move to the parent menu.   3.1.4. Save environment settings  Press  [F4(←)]  key  in  the  main  menu  screen  of  <Figure  3-1>  to  save  the  settings changed, then the following screen will appear.
AC-5000 User Guide                                                                                                                                                   22 UNIONCOMMUNITY Co., Ltd. / 3F Hyundai Topics Bldg. 44-3 Bangi-dong Songpa-gu, Seoul, Korea (138-050) Tel : 02-6488-3000 , Fax : 02-6488-3099, E-Mail :sales@unioncomm.co.kr http://www.unioncomm.co.kr <Figure 3-6>  Select  [1.Yes]  to  save  the  revised  contents  or  [2.No]  to  cancel  it,  and  then  press [ENT] key. If there is no input for a certain period of time in this case, it returns to the initial screen.    If  there is no revised contents, it exits from the environment settings menu without the aforementioned process of “Save?”.    When the settings are changed in the menu, if there is no input for a certain period of time, it exits from the environment setting menu. In this case, if there is any menu revised, it  should  pass through the “Save?” process. Otherwise, it  transfers  to  the initial screen without saving the revised setting.
AC-5000 User Guide                                                                                                                                                   23 UNIONCOMMUNITY Co., Ltd. / 3F Hyundai Topics Bldg. 44-3 Bangi-dong Songpa-gu, Seoul, Korea (138-050) Tel : 02-6488-3000 , Fax : 02-6488-3099, E-Mail :sales@unioncomm.co.kr http://www.unioncomm.co.kr  3.2. Menu Configuration  1. User  1. Add 2. Delete 3. Modify 4. Delete All 1. IP  1. Static IP / 2. DHCP IP Address Subnet Mask Gateway 2. Server IP  Server IP Server Port 2. Network  3. Terminal ID  Terminal ID Authentication 1. Application  Application 1. Access 2. Time & Attendance 3. Cafeteria 2. Time Schedule  F1 Time F2 Time F3 Time F4 Time Access Time □NO  Limit  (when  setting  to  catering management) 3. Function Key  □F1 Enabled □F2 Enabled □F3 Enabled □F4 Enabled □Ent Enabled   □Auto Sensing 4. Extended Key  □ Extended Key of Extended Key 3. Application  5. Display  Background Clock Position □User Voice □User Text
AC-5000 User Guide                                                                                                                                                   24 UNIONCOMMUNITY Co., Ltd. / 3F Hyundai Topics Bldg. 44-3 Bangi-dong Songpa-gu, Seoul, Korea (138-050) Tel : 02-6488-3000 , Fax : 02-6488-3099, E-Mail :sales@unioncomm.co.kr http://www.unioncomm.co.kr  1. System Setting  UserID Length Display Option 2. Authentication  User GroupIP Enable 1:N Card Only Template On Card Verify Multi-FP Blocking Time (sec.) 3. Fingerprint  1:1 Level [1~9] 1:N Level [3~9] Fake Finger Detect □Check SameFP 4. Language   5. Data Time  Time Sync Display Time Set Current Time 4. System  6. Database  1. Init Config 2. Delete All Users 3. Clear Log Data 4. Initialize Terminal 1. Terminal Option  □Terminal Alarm □Lock Terminal □KeyLed ON 2. Volume Control  Voice Volume Beeper Volume 3. Door  Lock Type Door Monitor Open Duration Warn Door Open 4. Wiegand  □Bypass Wiegand Out Site Code 5. Card Reader  Card Format Read Card NO. 5. Terminal  6. External Device  Printer Lock Controller
AC-5000 User Guide                                                                                                                                                   25 UNIONCOMMUNITY Co., Ltd. / 3F Hyundai Topics Bldg. 44-3 Bangi-dong Songpa-gu, Seoul, Korea (138-050) Tel : 02-6488-3000 , Fax : 02-6488-3099, E-Mail :sales@unioncomm.co.kr http://www.unioncomm.co.kr 6. Information  1. System Info 2. Network Info 3. Database Info 4. View Log 5. Version Info   3.3. User  Select “1. User” in the main menu, then the following screen will appear.   Press [1] key to register new user,   [2] key to delete user,   [3] key to modify user, and   [4] key to delete all users.   3.3. 1. Add    Select [ENT~]  [1. User]  [1. Add]    in the basic screen, then the following screen will appear.   Input  the  user  ID  to  be  registered  and  then  press [ENT] key.  In this case, it automatically shows the ID that  can be registered on the screen, so the user can easily perform  registration.  To  modify  the  ID,  press [F4(←)]  key  and  delete  the  existing  value  and input the new value.   If the user  inputs an already registered ID,  a failure message will appear. The following screen will appear if the ID is not yet registered.   The icon at left has the meaning as below;   Authentication type   Number of fingerprints registered (0~10)   Number of cards registered (0~10)   Whether  or  not  password  is  registered ( :Registered/ :Not registered)
AC-5000 User Guide                                                                                                                                                   26 UNIONCOMMUNITY Co., Ltd. / 3F Hyundai Topics Bldg. 44-3 Bangi-dong Songpa-gu, Seoul, Korea (138-050) Tel : 02-6488-3000 , Fax : 02-6488-3099, E-Mail :sales@unioncomm.co.kr http://www.unioncomm.co.kr As shown on the screen, the user can register by pressing [2] for fingerprint, [3] for card, and [4] for password. Basically, it is registered in the name of the user. Using the keys [7] and  [8],  the  user  can  modify  into  the  user  and  the  admin.  Once  the  registration  is completed,  the  user  can  press  [ENT]  to  save  it.  The  user  must  press  [F4(←)]  key  to cancel the registration and exit from the menu.    Only  the  user  registered  as  admin  can  modify  the  operating  environment  of  the terminal,  and  Add/Modify/Delete  the  information  of  all  the  users  saved  in  the  terminal. Therefore, special care is required for the registration of the admin.   3.3.1.1. Auth Type     Delete  the  existing  value  by  pressing  [F4(←)]  key, enter one of the 12 authentication types shown on the screen, and then press [ENT] key.   3.3.1.2. FP Register       Place  finger  on  the  sensor  referring  to  ‘1.8. How  to  register  and  enter  fingerprint‘.  Fingerprint must be input two times as below in accordance with the guidance on the screen.  When  the  fingerprint  sensor  is  lit  together  with  the message ‘Place Finger on sensor‘, place the finger on the window for fingerprint input for 2~3 seconds until the light is off.   When  the  message  ‘Place  same  Finger  on sensor‘  appears,  enter  once  again  the  fingerprint input just before.  At the time of entering the fingerprint for the second time, input it  again after the user takes the finger off the fingerprint input window.
AC-5000 User Guide                                                                                                                                                   27 UNIONCOMMUNITY Co., Ltd. / 3F Hyundai Topics Bldg. 44-3 Bangi-dong Songpa-gu, Seoul, Korea (138-050) Tel : 02-6488-3000 , Fax : 02-6488-3099, E-Mail :sales@unioncomm.co.kr http://www.unioncomm.co.kr   When  input  is  complete,  the  message  at  the  left will  appear  together  with  its  image  accompanied  by quality rating in 0~100. If the image is not adequate from the visual aspect or   any image shows 30 or less, the user is advised to register again.   To  register  again,  start  the  process  from   by pressing  [F4(←)]  key  until  3  seconds  elapse  without input  or  pressing  another  key.  After  completion,  it moves to the parent menu.    Fingerprint  registration  is  available  up  to  10  per  ID.    Failure  message  will  appear when registration is attempted in excess of 10.  In  case  that  failure  is  repeated  in  spite  of  the  attempts  for  2~3  times  using  the  correct fingerprint registration method, the user is advised to use password or card.   3.3.1.3. Card Register   When registration screen appears, put the card on it. If you want to exit without registration, press [F4(←)] key.   3.3.1.4. PW Register
AC-5000 User Guide                                                                                                                                                   28 UNIONCOMMUNITY Co., Ltd. / 3F Hyundai Topics Bldg. 44-3 Bangi-dong Songpa-gu, Seoul, Korea (138-050) Tel : 02-6488-3000 , Fax : 02-6488-3099, E-Mail :sales@unioncomm.co.kr http://www.unioncomm.co.kr    Input  the  password  in  1~8  digits  on  the  password input  screen  and  press  [ENT]  key.  The  ‘Confirm Password’ window will appear  again. Input the same password and press [ENT] key.  Press [F4(←)] key for 2 seconds or longer to cancel it and exit.   3.3.1.5. FP Option  As  it  is  the  settings  related  with  fingerprint,  it  is  the  option  that  can  be  changed  after registering  the  fingerprint  in  advance.  If  the  user  selects  it  with  the  fingerprint  already registered, it only results in the buzzer sound of failure.   ’1:1 Level’ (Initial setting: ‘0’) It  is  the  item  that  determines  the  authentication level  for  each  user  registered.  By  modifying  this value, it is possible to determine the authentication level by registered users.       When set to ‘0’, it conducts authentication using 1:1 authentication level of the terminal. Enable 1:N (Initial setting: ‘v’) When this option is checked,    it is possible to successfully  authenticate  using  fingerprint without any user ID or card.   3.3.1.6. Save  When registration process is finally completed, press [6] key to save it. In this case, the user is not saved if the user doesn’t press [6] key but exits by pressing [F4(←)] key..  The  following  is  the  LCD  guidance  message  indicating  that  the  user  can  exit  from  the registration process.
AC-5000 User Guide                                                                                                                                                   29 UNIONCOMMUNITY Co., Ltd. / 3F Hyundai Topics Bldg. 44-3 Bangi-dong Songpa-gu, Seoul, Korea (138-050) Tel : 02-6488-3000 , Fax : 02-6488-3099, E-Mail :sales@unioncomm.co.kr http://www.unioncomm.co.kr  When it is registered normally with [6. Save] key pressed  When registration is failed with [6. Save] key pressed  When the registration means is not registered properly in accordance  with  the  authentication  method,  for example,  the  user  didn’t  register  any  fingerprint  after setting it as authentication means, nor register any card after setting it as authentication means.  In the case of [2. FP Register]  When fingerprint image is not in good condition or there is no fingerprint input for 10 seconds after the fingerprint sensor lamp is on  At  the  time  of  fingerprint  registration,  when  the  user didn’t  input  the  same  fingerprint  but  inputs  a  different fingerprint   In the case of [4. PW Register]  When  the  user  inputs  a  different  number  during verification after inputting the password      In the case of [3. Card Register]  When the user intends to register a card that has been already registered
AC-5000 User Guide                                                                                                                                                   30 UNIONCOMMUNITY Co., Ltd. / 3F Hyundai Topics Bldg. 44-3 Bangi-dong Songpa-gu, Seoul, Korea (138-050) Tel : 02-6488-3000 , Fax : 02-6488-3099, E-Mail :sales@unioncomm.co.kr http://www.unioncomm.co.kr  In  case  of  [2.  FP  Register],  when  the  user  intends  to register  again  the  fingerprint  that  has  already  been registered.    If  the  user  wants  to  register  the  same  fingerprint with other ID again, he/she must release ‘4. System  3.  Fingerprint    Check  SameFP’  function.  This  is, however,  not  suitable  for  time  &  attendance,  etc.  as the  same  fingerprints  can  be  authenticated  with different IDs at the time of authentication.  In case of [2. FP Register] or [3. Card Register]  When  the  user  attempted  registration  in  excess  of  the maximum number of registrations (10 each)   3.3.2. Delete  When the user selects    [ENT~]  [1.  User]   [2. Delete] in the initial screen  , the following screen will appear.   Input  the  user  ID  to  be  deleted,  and  then  press [ENT] key.  When  inputting  an  unregistered  ID,  the  failure message will  appear. When  inputting  a  registered ID, the success message will appear.   Deleting  from  the  terminal  doesn’t  mean  the  deletion  from  the  server.  Therefore,  it  is necessary to delete from the server in order to completely delete it.  Special care should be taken in case of deletion, since deletion is performed regardless of User/Admin.  Especially,  the  user  registered  in  the  terminal  may  not  be  restored  after deletion unless it is registered in the network server.  The  following  is  the  LCD  information  message  that  may  appear  during  the  process  of deletion;
AC-5000 User Guide                                                                                                                                                   31 UNIONCOMMUNITY Co., Ltd. / 3F Hyundai Topics Bldg. 44-3 Bangi-dong Songpa-gu, Seoul, Korea (138-050) Tel : 02-6488-3000 , Fax : 02-6488-3099, E-Mail :sales@unioncomm.co.kr http://www.unioncomm.co.kr  When it is deleted normally  When the user inputs an unregistered ID   3.3.3. Modify  When the user selects    [ENT~]  [1. User]  [3. Modify] in the initial screen  , the following screen will appear.   Press  [ENT]  key  after  inputting  the  user  ID  to  be changed.    When inputting  an  unregistered ID, the  failure message  will  appear. When  inputting a registered ID, the following screen will appear.   The  icons  at  the  left  are  described  by  their respective meanings on the right.   Authentication type (FP)   Number of registered fingerprints (1)   Number of registered cards (0)   Whether  or  not  the  password  is  registered ( : not registered)  For the changing method, see ‘3.3.1. Add’ as it is the same as shown in the registration method.
AC-5000 User Guide                                                                                                                                                   32 UNIONCOMMUNITY Co., Ltd. / 3F Hyundai Topics Bldg. 44-3 Bangi-dong Songpa-gu, Seoul, Korea (138-050) Tel : 02-6488-3000 , Fax : 02-6488-3099, E-Mail :sales@unioncomm.co.kr http://www.unioncomm.co.kr   3.3.4. Delete All  When the user selects    [ENT~]  [1. User]  [4. Delete All] in the initial screen  , the following screen will appear.    If the user is sure to delete all users, press [1.Yes] while  press  [ENT]  key  after  selecting  [2.No]  to cancel it.  When  the  user  selects  [1.Yes],  both  user  and admin are deleted. Special care should be taken as  the  deleted  user/admin  may  not  be  restored after deletion.    3.4. Network  When the user selects “2. Network” in the main menu, the following screen will appear.   Press  the  applicable  key  that  represents  the  item  to be changed.   3.4.1. IP  When the user selects    [ENT~]  [2. Network]  [1. IP] in the initial screen  , the following screen will appear.   At  the  time  of  changing  IP,  delete  the  existing  value using [F4(←)] and then input the new value. The ‘.’ in between  the  number  sequence  is  created automatically.  Ex)  input 192  168  010  50  sequentially to input ‘192.168.10.50’.  Select [1] in case of the method that a fixed IP is assigned from the connected network while  select  [2]  in  case  of  the  method  that  there  is  a  DHCP  server  in  the  connected network from which IP is assigned. Set IP, Subnet Mask, and Gateway if it is the fixed IP;
AC-5000 User Guide                                                                                                                                                   33 UNIONCOMMUNITY Co., Ltd. / 3F Hyundai Topics Bldg. 44-3 Bangi-dong Songpa-gu, Seoul, Korea (138-050) Tel : 02-6488-3000 , Fax : 02-6488-3099, E-Mail :sales@unioncomm.co.kr http://www.unioncomm.co.kr No need to set them if the user selected a flexible IP.          The user can exit to the parent menu using [ENT~] key to apply the changed value after finishing the  setting  while using  [F4(←)] key to cancel input  during setting. In this case, the user can exit only by pressing the key for 2 seconds or longer if he/she is inputting the value in the input box.   3.4.2. Server IP  When the user selects    [ENT~]  [2. Network]  [1. Server IP] in the initial screen  , the following screen will appear.  Set the Server IP and Port.    To  change  the  port,  input  it  after  moving  the  input focus to the server port by pressing [ENT] key.  Initial setting Server Port: ‘9870’   The  basic  port  value  of  authentication  server  is  ‘9870’  for  UNIS  server,  while  ’2201’  for Access  server.  Special  care  should  be  taken  since  changing  these  values  requires  the similar changes in the server program.  The user can exit to the parent menu by pressing [ENT~] key to apply the changed value after finishing the setting while pressing [F4(←)~] key to cancel the input value.   3.4.3. Terminal ID  When the user selects   [ENT~] ( [2. Network] ( [3. Terminal ID] in the initial screen  , the following screen will appear.    Set Terminal ID and Authentication.  Initial setting   Terminal ID: ‘1’   Authentication: ‘2. terminal/server’  Terminal ID is a unique ID used by the authentication server for the purpose of identifying the terminal having ‘1’ as its default value. It must correspond to the entry/exit door ID set in the server program, which can be input in a maximum of 8 digits.        Authentication This item determines the priority for authentication between terminal and network server.  Having  ‘2.  Terminal/Server’  as  its  default  value,  it  operates  as  follow  in  each mode.
AC-5000 User Guide                                                                                                                                                   34 UNIONCOMMUNITY Co., Ltd. / 3F Hyundai Topics Bldg. 44-3 Bangi-dong Songpa-gu, Seoul, Korea (138-050) Tel : 02-6488-3000 , Fax : 02-6488-3099, E-Mail :sales@unioncomm.co.kr http://www.unioncomm.co.kr 1.Server/Terminal Authentication is made by the server when it is connected to the server while by the terminal when it is disconnected to the server due to network disturbance, etc. 2.Terminal/Server Authentication  is  made  by  the  terminal  even  if  the  server  is connected  and  the  result  of  authentication  is  transferred  to  the server on a real-time basis. However,  authentication  is  made  by  the  server  when  the  input user ID or card is not registered in the terminal. (It doesn’t attempt server authentication in case of 1:N fingerprint authentication) 3. Server Only  Although  the  user  is  registered  in  the  terminal,  authentication  is made  through  the  server.  Therefore,  authentication  is  not  made unless the server is connected. 4. Terminal Only  Only  the  user  registered  in  the  terminal  is  authenticated.  When connected  to  the  server,  the  authentication  result  will  be transmitted to the server on a real-time basis.  Flexible  designation  is  allowed  depending  on  the  circumstance  such  as  the  number  of terminals  connected  to  the  server,  the  number  of  users  authenticated,  or  the  network error,  etc.  It  is  recommended  to  use  ‘2.  Terminal/Server’  so  that  concurrent authentications  could  be  attempted  when  at  least  10  terminals  are  connected  to  the server or when network error frequently occurs in general.   3.5. Application  When the user selects ‘3. Application’ in the main menu, the following screen will appear.   Press  the  applicable  key  that  represents  the  item  to be changed.   3.5.1. Application  When the user selects    [ENT~]  [3. Application]  [1. Application] in the initial screen , the following screen will appear.
AC-5000 User Guide                                                                                                                                                   35 UNIONCOMMUNITY Co., Ltd. / 3F Hyundai Topics Bldg. 44-3 Bangi-dong Songpa-gu, Seoul, Korea (138-050) Tel : 02-6488-3000 , Fax : 02-6488-3099, E-Mail :sales@unioncomm.co.kr http://www.unioncomm.co.kr  Select the operation type of the terminal by pressing the applicable number key.  Press  [ENT]  key  to  apply  the  configuration  while [F4(←)] key to cancel it.   3.5.2. Time Schedule  3.5.2.1. Setting to Access / Time & Attendance  When the user selects    [ENT~]  [3. Application]  [2. Time Schedule] in the initial screen  , the following screen will appear.    Initial setting: Identical with the screen at the left  The  user  can  set  the  time  zone  by  authentication modes; otherwise, set to ‘00:00-00:00’..  Input after deleting the existing value using [F4(←)] to change the value. Input HHMM (Hour/Minute) in the order which can be set from 00:00 to23:59  In the preset time zone, it is always indicated in the preset mode unless the user presses the other function key. Although the user pressed the other function key to authenticate with another mode, terminal display  mode  is automatically changed  into authentication mode, which is suitable for the management of time & attendance.  As shown in the example below, each time zone must be set without being overlapped, but  the  mode  is  determined  like  F1F2F3F4Access  sequentially  if  they  are overlapped.  ----------------------------------------------------------------------------------------------------------- (Ex) Office start=06:00~09:59, Office leave=17:00~22:00  -----------------------------------------------------------------------------------------------------------
AC-5000 User Guide                                                                                                                                                   36 UNIONCOMMUNITY Co., Ltd. / 3F Hyundai Topics Bldg. 44-3 Bangi-dong Songpa-gu, Seoul, Korea (138-050) Tel : 02-6488-3000 , Fax : 02-6488-3099, E-Mail :sales@unioncomm.co.kr http://www.unioncomm.co.kr Exit to the parent menu by pressing [ENT~] key to apply the changed value after finishing the setting while pressing [F4(←)~] key to cancel the input value.   3.5.2.2. . Setting to Cafeteria   Initial setting: Identical with the screen at the left  The  user  can  set  the  time  zone  by  meal  types; otherwise, set to ‘00:00-00:00’.   NO Limit When  releasing  the  check  box  ( ),  each  user  is  allowed  for  one  authentication  by meal  only,  but  when  the  user  checks  the  box  ( )  he/she  is  allowed  for  several authentications regardless of the existing authentication.     3.5.3. Function Key      When the user selects    [ENT~]  [3. Application]  [3. Function Key] in the initial screen  , the following screen will appear.   Initial setting: Identical with the screen at the left   Function key means the key including [F1]~[F4], [ENT] used to change the authentication mode  such  as  office  start/office  leave,  etc.  When  the  user  presses  the  function  key, authentication  mode  is  changed  into  the  applicable  mode.  When  it  is  not  checked, authentication mode is not changed even though the applicable key is pressed. Therefore, it can be used with the checked other function key released in the event of using it as the terminal exclusively for office start or office leave.  In case of releasing the check box of ‘6.Auto Sensing’, fingerprint sensor doesn’t respond even if the user inputs his/her fingerprint on the sensor. In this case, be sure to input the ID or card or fingerprint of the user.   3.5.4. Extended Key
AC-5000 User Guide                                                                                                                                                   37 UNIONCOMMUNITY Co., Ltd. / 3F Hyundai Topics Bldg. 44-3 Bangi-dong Songpa-gu, Seoul, Korea (138-050) Tel : 02-6488-3000 , Fax : 02-6488-3099, E-Mail :sales@unioncomm.co.kr http://www.unioncomm.co.kr When the user selects    [ENT~]  [3. Application]  [4. Extended Key] in the initial screen  , the following screen will appear.  ,    Initial setting: Identical with the screen at the left  To  use  the  Extended  Key,  press  [1]  key  and  then check  ‘1.  Extended  Key.  The  number  of  extended keys can be set within the range of 1~40.          Extended  Key  is  the  function  that  extends  the  number  as  required  up  to  40  when  any additional  authentication  modes  are  necessary  in  addition  to  the  basic  function  key ([F1]~[F4], [ENT]). In this case, the screen for selecting the extended key as below when the user presses the F4 key. Select the applicable mode with [0]~[9] keys.   When  the  number  of  extended  keys  exceeds  10,  select  them  by  changing  the  page  with [F1]~[F4] key.  -----------------------------------------------------------------------------------------------------------         Ex) In case the number of extended keys is 16, press [F4] key in the initial screen, then the following screen will appear.                              If the user has to select  ExtMode 12, move to the next page with [F2] key and then press [2] key.               Press [ENT] key to exit without selecting the extMode. -----------------------------------------------------------------------------------------------------------  The  user  can  exit  to  the  parent  menu  using  [ENT~]  key  to  apply  the  changed  value  after finishing the setting while using [F4(←)] key to cancel input during setting.  3.5.5. Display      When the user selects    [ENT~]  [3. Application]  [5. Display] in the initial screen  , the following screen will appear.
AC-5000 User Guide                                                                                                                                                   38 UNIONCOMMUNITY Co., Ltd. / 3F Hyundai Topics Bldg. 44-3 Bangi-dong Songpa-gu, Seoul, Korea (138-050) Tel : 02-6488-3000 , Fax : 02-6488-3099, E-Mail :sales@unioncomm.co.kr http://www.unioncomm.co.kr  Initial setting: Identical with the screen at the left  Background image The user can change the background image of the initial screen by pressing [1] and [2] keys. Also, the user  can  set  the  cycle  to  5  seconds  or  longer  to have the background images saved in the terminal displayed  sequentially  at  every  preset  interval (seconds).  Clock Position Changes the location of the clock appearing on the initial screen  Based  on  the  user’s  need/preference,  he/she  can  download  the  voice  from  Wav  file (16bit/8KHz)  to  change  the  voice  output  when  authentication  is  successful  or  failed.  In addition, the user can download the image text in a modified form such as office start or office leave using the specially provided resource file (Excel file).    In this case, the user can apply the applicable modified contents when only the boxes of ‘6. User Voice’, and ‘7. User Text’ are checked. For the downloading method, see ‘3.9.Download customized file’  The  user  can  exit  to  the  parent  menu  using  [ENT~]  key  to  apply  the  changed  value  after finishing the setting while using [F4(←)] key to cancel input during setting. .   3.6. System  When selecting ‘4. System’ in the main menu, the following screen will appear.   Press  the  applicable  key  that  represents  the  item  to be changed.   3.6.1. System Setting  When the user selects    [ENT~]  [4. System]  [1. System Setting] in the initial screen  , the following screen will appear.
AC-5000 User Guide                                                                                                                                                   39 UNIONCOMMUNITY Co., Ltd. / 3F Hyundai Topics Bldg. 44-3 Bangi-dong Songpa-gu, Seoul, Korea (138-050) Tel : 02-6488-3000 , Fax : 02-6488-3099, E-Mail :sales@unioncomm.co.kr http://www.unioncomm.co.kr  Initial setting: Identical with the screen at the left     UserID Length This  field  sets  the  length  of  user  ID,  which  can  be  changed  within  the  range  of  1~9 digits. It must be  identical with  the  length  of  ID  registered  in  the server program.  For example, the user must set it to 6 if the ID registered in the server program is ‘000075’ which is 6 digits.      Display Option If  set  to  ‘1.  None’,  it  displays  the  authentication  result  message  only  when authentication is successful. If set to ‘2’, it displays the User ID. If set to ‘3’, ‘4’, and ‘5’, it displays the User Name, User Key, and Message respectively on the LCD screen. However,  it  indicates  the  ID  in  case  there  is  no  applicable  information  of  the  user saved in the terminal.    The  user  can  exit  to  the  parent  menu  using  [ENT~]  key  to  apply  the  changed  value  after finishing the setting while using [F4(←)] key to cancel input during setting. .   3.6.2. Authentication  When the user selects    [ENT~] ( [4. System] [2. Authentication] ) in the initial screen  , the following screen will appear.  Initial setting: Identical with the screen at the left    User GroupIP As the method of authentication regarding the initial digit of ID as the same group, it can finish 1:N authentication more quickly if at least 5,000 users are registered. When this  method is checked, it authenticates the  fingerprint out  of the users whose  ID starts with the input letter. If this method is not checked, it considers the input figure as the user ID and attempts 1:1 authentication against the fingerprint of the user with the applicable ID Ex) Where the user inputs ‘12’ to  attempt authentication when the user ID is  a 4-digit figure; If  checked  ( ),  it  attempts  1:N  authentication  among  the  users  having  ID ‘1200’~’1299’, If  unchecked  ( ),  it  attempts  1:1  authentication  against  the  fingerprints  of  the users whose ID is ‘12’.  Enable 1:N If  checked  ( ),  this  option  enables  to  authenticate  with  fingerprint  only  without inputting user ID or card. Even if the user is registered with 1:N authentication, only 1:1
AC-5000 User Guide                                                                                                                                                   40 UNIONCOMMUNITY Co., Ltd. / 3F Hyundai Topics Bldg. 44-3 Bangi-dong Songpa-gu, Seoul, Korea (138-050) Tel : 02-6488-3000 , Fax : 02-6488-3099, E-Mail :sales@unioncomm.co.kr http://www.unioncomm.co.kr authentication is permitted in the terminal where this option is not checked  Card Only If  checked  ( ),  this  option  enables  to  authenticate  with  card  only  without  inputting fingerprint.  Even  if  the  user  is  registered  with  (Card  &  FP)  or  (Card  &  PW),  only authentication with card is permitted in the terminal where this option is checked.  Template On Card If  checked  ( ),  this  option  enables  to  authenticate  with  the  user’s  information  and fingerprint recorded in the card without downloading the user in the terminal. In  order for  this  option  to  be  operated,  SCcard  reader  must  be  mounted  without  fail  and  the server must set the terminal that uses fingerprint card.    Verify Multi-FP If checked ( ), this function has all the registered fingerprints to be authenticated after the user inputs ID (or Card). When this item is set to be checked, the user must input user ID or  card without fail. In this case, Enable 1:N  is  changed into unchecked  ( ) automatically.  This function is used for strict access control of the special zone. For example, if the   user with ID ‘0001’ is registered with 3 fingerprints, he/she must input ID and   complete the authentication for three fingerprints. In  this  case,  the  order  of  authentication  for  3  fingerprints  is  irrelevant,  but  the fingerprints should be repeatedly input until authentication is successful. Authentication will fail even at a single occurrence of authentication failure.    Blocking Time (sec) This is the function that prevents duplicate authentication for the same user within the preset  time  zone. When set  to  0, it  has  no  restriction.  However,  when  set  to  a  value larger  than  0,  the  user  can  be successful  in re-authentication  if  the  preset time  (sec) has elapsed after the success of the previous authentication.  The  user  can  exit  to  the  parent  menu  using  [ENT~]  key  to  apply  the  changed  value  after finishing the setting while using [F4(←)] key to cancel input during setting. .   3.6.3. Fingerprint  When the user selects    [ENT~]  [4. System]  [3. Fingerprint] in the initial screen  , the following screen will appear.   Initial setting: Identical with the screen at the left
AC-5000 User Guide                                                                                                                                                   41 UNIONCOMMUNITY Co., Ltd. / 3F Hyundai Topics Bldg. 44-3 Bangi-dong Songpa-gu, Seoul, Korea (138-050) Tel : 02-6488-3000 , Fax : 02-6488-3099, E-Mail :sales@unioncomm.co.kr http://www.unioncomm.co.kr  1:1 Level Authentication level that  is  used for  1:1  Fingerprint  Authentication,  provided  that,  1:1 authentication  level  of  the  relevant  user  shall  apply  for  the  user  whose  1:1 authentication level is not set to ‘0’ (using the authentication level of the terminal)  1:N Level Authentication  level  that  is  used  for  1:N  Fingerprint  Authentication.  In  case  of  1:N authentication, the authentication level  by  users  is  not  set  and  therefore, it  is  always based on the authentication level of the terminal.    Fake Finger Detect It  presets  LFD  level  that  can  prevent  imitation  fingerprint  input.  When  presetting  the LFD level to a higher value, it tends to reinforce the function that prevents the input of imitation  fingerprint  produced  with  rubber,  paper,  film,  silicone,  etc.  But  even  when inputting a real fingerprint, it may not input well if it is in dry condition.    Check SameFP If checked ( ),  it is the function that checks whether or not the fingerprint is already registered  during  registration  so  as  to  prevent  overlapped  registration  of  the  same fingerprint in another user ID.  The  user  can  exit  to  the  parent  menu  using  [ENT~]  key  to  apply  the  changed  value  after finishing the setting while using [F4(←)] key to cancel input during setting. .   3.6.4. Language  When the user selects    [ENT~]  [4. System]  [4. Language] in the initial screen  , the following screen will appear.   Initial setting: ‘1. English’  When  changing  the  language  settings,  the  voice message  and  on-screen  message  are  changed  into the language set.  The  user  can  exit  to  the  parent  menu  using  [ENT~]  key  to  apply  the  changed  value  after finishing the setting while using [F4(←)] key to cancel input during setting. .   3.6.5. Data Time  When the user selects    [ENT~]  [4. System]  [5. Data Time] in the initial screen  , the following screen will appear.
AC-5000 User Guide                                                                                                                                                   42 UNIONCOMMUNITY Co., Ltd. / 3F Hyundai Topics Bldg. 44-3 Bangi-dong Songpa-gu, Seoul, Korea (138-050) Tel : 02-6488-3000 , Fax : 02-6488-3099, E-Mail :sales@unioncomm.co.kr http://www.unioncomm.co.kr  Initial setting: Identical with the screen at the left     Time Sync It sets the method that synchronizes the current time of the terminal with the server. To synchronize  the  terminal  time  with  the  server  time,  set  to  ‘1.  Auto’  to  perform  it automatically while ‘2. Manual’ to perform it manually.    Display Time     The method of displaying the current time of the terminal set to ‘1’ for 24-hour system and ‘2’ for AM/PM system    Set Current Time     It changes the current time of the terminal. No change is required as it is synchronized with the server time when linked to the server with the aforementioned Time Sync set to ‘1. Auto’.         The  user  can  exit  to  the  parent  menu  using  [ENT~]  key  to  apply  the  changed  value  after finishing the setting while using [F4(←)] key to cancel input during setting.   3.6.6. Database  When the user selects    [ENT~]  [4. System]  [6. Database] in the initial screen  , the following screen will appear.    Press the following keys; [1] key to initialize the configuration, [2] key to delete all users, [3] key to initialize the authentication record, and [4] key to initialize the terminal.   3.6.6.1 Init Config  When the user selects    [ENT~]  [4. System]  [6. Database]  [1. Init Config] in the initial screen  , the following screen will appear.
AC-5000 User Guide                                                                                                                                                   43 UNIONCOMMUNITY Co., Ltd. / 3F Hyundai Topics Bldg. 44-3 Bangi-dong Songpa-gu, Seoul, Korea (138-050) Tel : 02-6488-3000 , Fax : 02-6488-3099, E-Mail :sales@unioncomm.co.kr http://www.unioncomm.co.kr  Press  [1.Yes]  key  to initialize all  configurations while select [2.No] and press [ENT] key to cancel it.  When no value is input for a certain period of time in this  state,  it  returns  to  the  initial  screen  instead  of initialization.  It  initializes  all  the  configurations  of  the  terminal  except  MAC  (physical)  address  but  it doesn’t delete the user and authentication record. When  the  configuration  is  successfully  initialized,  it  proceeds  to  the  parent  menu accompanied by the success buzzer sounds.  3.6.6.2. Delete All Users  When the user selects    [ENT~]  [4. System]  [6. Database]  [2. Delete All Users] in the initial screen  , the following screen will appear.    Press  [1.Yes]  key  to  delete  all  users  while  select [2.No] and press [ENT] key to cancel it.  When no value is input for a certain period of time in this  state,  it  returns  to  the  initial  screen  instead  of deletion.  Both user and administrator are deleted, and the deleted users may not be restored after deletion. When deletion is successfully completed, it proceeds to the parent menu accompanied by the success buzzer sounds.  3.6.6.3. Clear Log Data  When the user selects    [ENT~]  [4. System]  [6. Database]  [3. Clear Log Data] in the initial screen  , the following screen will appear.    Press  [1.Yes]  key  to  delete  all  the  authentication records saved in the terminal while select [2.No] and press [ENT] key to cancel it.  When no value is input for a certain period of time in this  state,  it  returns  to  the  initial  screen  instead  of deletion.
AC-5000 User Guide                                                                                                                                                   44 UNIONCOMMUNITY Co., Ltd. / 3F Hyundai Topics Bldg. 44-3 Bangi-dong Songpa-gu, Seoul, Korea (138-050) Tel : 02-6488-3000 , Fax : 02-6488-3099, E-Mail :sales@unioncomm.co.kr http://www.unioncomm.co.kr  It deletes all the logs related to authentication, and the deleted logs may not be restored after deletion. When deletion is  successfully completed, it proceeds  to  the  parent menu  accompanied by the success buzzer sounds.   3.6.6.4. Initialize Terminal  When the user selects    [ENT~]  [4. System]  [6. Database]  [4. Initialize Terminal] in the initial screen  , the following screen will appear.    Press  [1.Yes]  key  to  initialize  the  terminal  to  the factory  default  state  while  select  [2.No]  and  press [ENT] key to cancel it.  When no value is input for a certain period of time in this  state,  it  returns  to  the  initial  screen  instead  of initialization.  It  deletes  all  the  configurations,  users,  and  log  information  except  MAC  (physical) address saved in the terminal, restoring it to the factory default state. Special care should be taken as restoration is impossible after it is initialized. When  initialization to  the  factory  default  state  is  successfully  completed,  it  proceeds  to the parent menu accompanied by the success buzzer sounds  3.7. Terminal  When selecting ‘5. Terminal’ in the main menu, the following screen will appear.   Press  the  applicable  key  that  represents  the  item  to be changed   3.7.1. Terminal Option  When the user selects    [ENT~]  [5. Terminal]  [1. Terminal Option] in the initial screen  , the following screen will appear.
AC-5000 User Guide                                                                                                                                                   45 UNIONCOMMUNITY Co., Ltd. / 3F Hyundai Topics Bldg. 44-3 Bangi-dong Songpa-gu, Seoul, Korea (138-050) Tel : 02-6488-3000 , Fax : 02-6488-3099, E-Mail :sales@unioncomm.co.kr http://www.unioncomm.co.kr  Initial setting: Identical with the screen at the left  Dooropen Door is opened when pressing ‘0’ key. It appears only when the terminal is locked. This is  option not normally shown.    Terminal Alarm If checked, ( ), it generates a warning sound when the lid of the terminal is opened.    Lock Terminal This is the function that the administrator can directly set or release the locking of the terminal through the terminal instead of server program. If checked ( ), it is locked so that no one can access until the administrator releases the settings.            KeyLed ON If checked ( ), Key LED is always turned ON so that Touch Key is visible.            Dooropen This is the menu that shows the terminal administrator is allowed to temporarily open the door where the terminal is set to lock in the server.  The  user  can  exit  to  the  parent  menu  using  [ENT~]  key  to  apply  the  changed  value  after finishing the setting while using [F4(←)] key to cancel input during setting. .   3.7.2. Volume Control  When the user selects    [ENT~]  [5. Terminal]  [2. Volume Control ] in the initial screen  , the following screen will appear.    Initial setting: Identical with the screen at the left  Sets Voice Volume and Beeper Volume. When  set  to  ‘0’,  no  voice  or  buzzer  sound  is generated.  The  user  can  exit  to  the  parent  menu  using  [ENT~]  key  to  apply  the  changed  value  after finishing the setting while using [F4(←)] key to cancel input during setting. .
AC-5000 User Guide                                                                                                                                                   46 UNIONCOMMUNITY Co., Ltd. / 3F Hyundai Topics Bldg. 44-3 Bangi-dong Songpa-gu, Seoul, Korea (138-050) Tel : 02-6488-3000 , Fax : 02-6488-3099, E-Mail :sales@unioncomm.co.kr http://www.unioncomm.co.kr  3.7.3. Door  When the user selects    [ENT~]  [5. Terminal]  [3. Door]    in the initial screen  , the following screen will appear.   Initial setting: Identical with the screen at the left    Lock Type             Set  to  ‘1’  when  strike  type  or  automatic  door  is  connected  with  the  terminal  while  ‘2’ when motor lock is connected to the terminal. In case that no connection is made, it is also set to ‘1’. Set to ‘3’ when connecting the warning lamp to the lock port to indicate the success or failure of authentication.  Door Monitor     Set this function to know the door status       - ‘3.Disable’ – when not checking the door status       - ‘1.Normal Open’: In the case of dead bolt type or automatic door                   (When lock monitoring is open where the door is locked)               - ‘2.Normal Close’: In the case of Strike type           (When lock monitoring is locked where the door is locked)  Open Duration (0.1 sec unit)     It designates the time that the door is opened and closed again when authentication is successful. As it is set to 0.1 second unit, a value of 30 is required to set it to 3 seconds. Strike type refers to the time the door is opened and closed again when authentication is complete.    Warn Door Open (Second unit) This  is  the  function  that  enables  the  terminal  to  check  the  time  of  the  door  being opened, and generates a warning sound once it exceeds the preset time (min. 5 sec~ max 30 sec). When set to ‘00’, warning doesn’t sound at all. Even if set to 01~04, it starts sounding when it exceeds at least 5 seconds.  The  warning  sound  is  also  generated  in  case  the  door  is  not  closed  unexpectedly within the preset time although the door should be closed. It allows for a proper action to be taken for the door to be  closed by informing about the fact that the door is not closed.    To operate this function, the lock must be the one that enables to monitor   the door status and the monitoring pin of lock should be connected to the terminal   without fail. In addition, such settings are enabled only when the aforementioned Door Monitor is set to ‘4. Normal Open’ or ‘5.Normal Close’.
AC-5000 User Guide                                                                                                                                                   47 UNIONCOMMUNITY Co., Ltd. / 3F Hyundai Topics Bldg. 44-3 Bangi-dong Songpa-gu, Seoul, Korea (138-050) Tel : 02-6488-3000 , Fax : 02-6488-3099, E-Mail :sales@unioncomm.co.kr http://www.unioncomm.co.kr  The  user  can  exit  to  the  parent  menu  using  [ENT~]  key  to  apply  the  changed  value  after finishing the setting while using [F4(←)] key to cancel input during setting. .   3.7.4. Wiegand  When the user selects [ENT~]  [5. Terminal]  [4. Wiegand] in the initial screen  , the following screen will appear.   Initial setting: Identical with the screen at the left    This is the menu that configures the Wiegand Output.  It is used only when a separate controller operating with Wiegand input is mounted. Upon successful  authentication,  it  transmits  the  data  to  the  terminal’s  Wiegand  port  in  the following form;  2.None    This is the normal case; Wiegand Outport is not used in this case. 3.26bit  It transmits “Sitecode[1byte] + user ID[2byte]”, so the user ID is set to 4 digits or less. Example)  In  the  case  of  SiteCode:045(2Dh),  UID:6543(198Fh),  it  is transmitted as ‘1 00101101 0001 1001 10001111 0’ 4.34bit  It transmits “Sitecode[1byte] + user ID[3byte]” so the user ID is set to 7 digits  or  less.  In  case  of  an  8-digit  user  ID,  “user  ID[4byte]”  is transmitted without Sitecode. Example)  In  the  case  of  SiteCode:001(1h), UID:123456(1E240h),  it  is transmitted as ‘0 00000001 00000001 11100010 01000000 0’ 5.Custom  It  can  be  set  in  the  server  as  the  settings  under  the  user’s  definition only. The setting type can only be inquired at the terminal.  However, when Bypass is checked, regardless of Wiegand Out settings, it transmits the data received by Wiegand Inport at the time when authentication was  successful to the Widgand Outport as it is.  The  user  can  exit  to  the  parent  menu  using  [ENT~]  key  to  apply  the  changed  value  after finishing the setting while using [F4(←)] key to cancel input during setting.    3.7.5. Card Reader
AC-5000 User Guide                                                                                                                                                   48 UNIONCOMMUNITY Co., Ltd. / 3F Hyundai Topics Bldg. 44-3 Bangi-dong Songpa-gu, Seoul, Korea (138-050) Tel : 02-6488-3000 , Fax : 02-6488-3099, E-Mail :sales@unioncomm.co.kr http://www.unioncomm.co.kr When the user selects [ENT~]  [5. Terminal]  [5. Card Reader] in the initial screen  , the following screen will appear.    Initial setting: Identical with the screen at the left    Read Card NO. When  the  user  puts  the  card  on  this  screen,  the card number will be displayed on the LCD.   Card Format             This is the menu that sets the manner of displaying the card number. As shown below, the  displayed  card  number  varies  depending  on  the  configuration.  Therefore,  if changing it during operation is unavoidable after it was set during initial installation, the card should be registered again.  RFcard example) Card number (5byte): 08h 01h 16h 1Dh D6h Card Format  Card Number Method of Expression 1. Default  02207638  (3+5)  digit  decimal  number [022(16h)+07638(1DD6h)] 2. Hexadecimal number 0801161DD6  10-digit hexadecimal number 3.  Decimal number  0018226646  Last  4byte  to  be  expressed  in  a  10-digit  decimal number (01161DD6h) 4.  Decimal number 35  02207638  Same as ‘1. Default’  SCcard example) Card Number (4byte): 52h 9Dh 06h E3h Card Format  Card Number Method of Expression 1. Default  529D06E3  Expressing in an 8-digit hexadecimal number 2. Hexadecimal number E3069D52  Expressing  in  an  8-digit  hexadecimal  number changing the order of byte 3.  Decimal number  1386022627  Hexadecimal number 529D06E3  to  be  expressed  in a 10-digit decimal number 4.  Decimal number 35  3808861522  Hexadecimal  number  E3069D52  to  be  expressed  in a 10-digit decimal number    The  user  can  exit  to  the  parent  menu  using  [ENT~]  key  to  apply  the  changed  value  after finishing the setting while using [F4(←)] key to cancel input during setting. .
AC-5000 User Guide                                                                                                                                                   49 UNIONCOMMUNITY Co., Ltd. / 3F Hyundai Topics Bldg. 44-3 Bangi-dong Songpa-gu, Seoul, Korea (138-050) Tel : 02-6488-3000 , Fax : 02-6488-3099, E-Mail :sales@unioncomm.co.kr http://www.unioncomm.co.kr  3.7.6. External Device  When the user selects [ENT~] ( [5. Terminal] [6. External Device] ) in the initial screen  , the following screen will appear.   Initial setting: Identical with the screen at the left            Printer             If  checked  ( ),  it  prints  out  the  authentication  result.  When  set  to  ‘1’,  if  authentication  is successful, the  terminal ID, user ID, authentication time, authentication mode, etc. are  printed out through the printer connected to the RS232 (Debug) port of the terminal. The print out type may  vary  depending  on  the  configuration.  When  set  to  ‘Format2’,  it  is  printed  out  with  the terminal name as the main subject. The printer used is   “SRP-350” Serial type.            Lock Controller Set to this function when the user connects a separate device instead of the terminal lock  port  to  control  the  door.  In  the  event  the  user  directly  connected  a  lock  to  the terminal, it is set to ‘4. None’, but it is set to ‘5.LC010’ when connected with LC010.  The  user  can  exit  to  the  parent  menu  using  [ENT~]  key  to  apply  the  changed  value  after finishing the setting while using [F4(←)] key to cancel input during setting. .   3.8. Information  When selecting ‘6. Information’ in the main menu, the following screen will appear.   Menu to inquire the setting condition of the terminal.  Press; [1]  key  to  inquire  a  variety  of  optional  configurations of the terminal, [2] key to inquire network configuration such as IP , [3] key to inquire the user registration status, etc. [4] key to inquire log data, [5] key to inquire firmware version.   3.8.1. System Info  Select    [ENT~]  [6. Information]  [6. System Info] in the initial screen
AC-5000 User Guide                                                                                                                                                   50 UNIONCOMMUNITY Co., Ltd. / 3F Hyundai Topics Bldg. 44-3 Bangi-dong Songpa-gu, Seoul, Korea (138-050) Tel : 02-6488-3000 , Fax : 02-6488-3099, E-Mail :sales@unioncomm.co.kr http://www.unioncomm.co.kr    Press [F4(←)] key to exit to the parent menu.   3.8.2. Network Info  Select    [ENT~]  [6. Information]  [2. Network Info] in the initial screen       Press [F4(←)] key to exit to the parent menu.   3.8.3. Database Info  Select    [ENT~]  [6. Information]  [3. Database Info] in the initial screen     -  Registered  User:  Number  of  registered  users (including administrator) -  Registered  Admin:  Number  of  registered administrators   -  Max  User:  Maximum  number  of  users  that  can  be registered -  Registered  FP:  Number  of  whole  fingerprints  that are registered -  Max  FP:  Maximum  number  of  fingerprints  that  can be registered   Press [F4(←)] key to exit to the parent menu.   3.8.4. View Log  Select    [ENT~]  [6. Information]  [4. View Log] in the initial screen
AC-5000 User Guide                                                                                                                                                   51 UNIONCOMMUNITY Co., Ltd. / 3F Hyundai Topics Bldg. 44-3 Bangi-dong Songpa-gu, Seoul, Korea (138-050) Tel : 02-6488-3000 , Fax : 02-6488-3099, E-Mail :sales@unioncomm.co.kr http://www.unioncomm.co.kr   - All Log: Number of logs saved in the terminal -  Max  Log:  Maximum  number  of  logs  that  can  be saved   Press [F4(←)] key to exit to the parent menu.   3.8.5. Version Info  Select    [ENT~]  [6. Information]    [5. Version Info] in the initial screen         Press [F4(←)] key to exit to the parent menu.   3.9. Downloading user’s file  The function allows the user to change background image or voice message when necessary. The user’s file can be downloaded from UNIS server program.   3.9.1. Change background image    When  selecting  ‘Download  customized  file’  in  UNIS  program,  the  following  screen  will appear.    Designate the file as ‘Background image file (.jpg)’, select the image file (.jpg), and click the  ‘Send’  button,  then  the  terminal  select  window  will  appear.  When  selecting  the terminal on the terminal list window and clicking the ‘Send’ button once again, the file will be transmitted with the downloaded result displayed.  In  this  case,  the  file name  can  be  selected  up  to  15 characters  including the  extension name  with  the  jpg  file  in  the  size  of  320*240  only.  If  any  data  in  a  different  format  is downloaded, the transmission result will be displayed in a version error.  To change background image, the user can directly select it from ‘3.5.5 Display”.
AC-5000 User Guide                                                                                                                                                   52 UNIONCOMMUNITY Co., Ltd. / 3F Hyundai Topics Bldg. 44-3 Bangi-dong Songpa-gu, Seoul, Korea (138-050) Tel : 02-6488-3000 , Fax : 02-6488-3099, E-Mail :sales@unioncomm.co.kr http://www.unioncomm.co.kr   3.9.2. Change Voice Message    When  selecting  ‘Download  customized  file’  in  UNIS  program,  the  following  screen  will appear.    Designate the file as ‘Success voice file (.wav)’, select Wav file (.wav) and click the ‘Send’ button, then the terminal select window will appear. When selecting the terminal from the terminal list window and clicking the ‘Send’ button once again, the file is transmitted with the downloaded result displayed.  In  this  case,  the  file name  can  be  selected  up  to  15 characters  including the  extension name with the Wav file in 8KHz, 16bit, in mono form only. If any data in a different format is downloaded, the transmission result will be displayed in a version error.          In  the  case  of  the  failure  voice,  designate  the  file  as  ‘Fail  voice  file  (.wav)’  and  then change it in the same way.  In order to change the user’s defined voice into default voice, release the check mark in the ‘User Voice’ item in ‘3.5.5 Display’.   3.9.3. Change User Text      When  selecting  ‘Download  customized  file’  in  UNIS  program,  the  following  screen  will appear.    Designate the file as ‘Defined Text File (.csv)’, select CSV file (.csv) and click the ‘Send’ button, then the terminal select window will appear. When selecting the terminal from the terminal list window and clicking the ‘Send’ button once again, the file is transmitted with the downloaded result displayed. CSV file can be saved and created in the form of csv type after changing the desired text   in the Excel (.xls) file provided together with the firmware of the terminal. In order to   change it from the user’s defined text to the default text, release the check mark in the   ‘User Text’ item in ‘3.5.5 Display’.
AC-5000 User Guide                                                                                                                                                   53 UNIONCOMMUNITY Co., Ltd. / 3F Hyundai Topics Bldg. 44-3 Bangi-dong Songpa-gu, Seoul, Korea (138-050) Tel : 02-6488-3000 , Fax : 02-6488-3099, E-Mail :sales@unioncomm.co.kr http://www.unioncomm.co.kr
AC-5000 User Guide                                                                                                                                                   54 UNIONCOMMUNITY Co., Ltd. / 3F Hyundai Topics Bldg. 44-3 Bangi-dong Songpa-gu, Seoul, Korea (138-050) Tel : 02-6488-3000 , Fax : 02-6488-3099, E-Mail :sales@unioncomm.co.kr http://www.unioncomm.co.kr  4. How to use terminal   4.1. Change of authentication mode   <Figure 4-1>  Normally, it is not visible; but when the user touches the hand on the card input area as shown  in  the  Figure  at  the  left,  LED  will  be  powered  ON  and  a  keypad  will  appear  as shown in the Figure at the right. When the key is visible, press the desired function key to change into the authentication mode such as office start [F1], office leave [F2], going-out [F3], return [F4], access [ENT], etc.     4.2. ID input  Normally, it is not visible; but as shown in Figure <4-1>, when the user touches the hand on the card input area, LED will be powered ON and a keypad will appear. In this case, ID input screen will appear when the user inputs the figure.    Press the desired mode key Touch the hand
AC-5000 User Guide                                                                                                                                                   55 UNIONCOMMUNITY Co., Ltd. / 3F Hyundai Topics Bldg. 44-3 Bangi-dong Songpa-gu, Seoul, Korea (138-050) Tel : 02-6488-3000 , Fax : 02-6488-3099, E-Mail :sales@unioncomm.co.kr http://www.unioncomm.co.kr   Delete with [F4(←)] key if the figure is wrongly input during the input process. When pressing [ENT] key after inputting ID, the fingerprint input or password input screen appears depending on the method of user authentication. However, authentication will fail if a card user inputs ID first. Therefore, be sure to use the card.   4.3. Authentication  4.3.1. Fingerprint Authentication          When  placing fingerprint on the fingerprint sensor,  buzzer sounds  with the  sensor  lamp ON,  and the fingerprint  is duly  input.  Be  sure  not  to take finger  off the  sensor  until  the sensor lamp is OFF and the buzzer sounds. In  the  case  of  1:1  authentication,  input  ID  and  press  [ENT]  key  causing  the  fingerprint sensor to flicker, and then input fingerprint to the fingerprint sensor.   4.3.2. Card Authentication          Touch the card on the figure of the card as shown in <Figure 4-1>.   4.3.3. Password Authentication      Press [ENT] key after inputting ID, then the screen for password input will appear. When a wrong number is input, delete it using [F4(←)] key. Input the password and press [ENT] key.

Navigation menu