UNITEIC 715003672 BRP STORM Audio Kit (MY19) User Manual

UNITEIC COMPANY LIMITED BRP STORM Audio Kit (MY19)

User Manual

Press and hold the power button (2) for 3-5 Seconds to power the system on. All blue lights indicate that the system is on.The Audio System defaults to Bluetooth mode, so the Bluetooth indicator (5) light should ash blue when powered on. If it is not lit or ashing, press it once to re-enter BT mode. Next turn on your Bluetooth device and search for Can-Am RST in the Bluetooth menu on your device, then select it for pairing. Your BT device will show “connected” to the Can-Am RST when you are successful.To connect a device to the Auxiliary (3.5mm) input, press the Bluetooth Indicator/Source Selector (5) once. When the blue light on this button is unlit, this indicates that the AUX input is active and you can connect a wired audio device with a 3.5mm male plug to the 3.5mm female jack on the system. To make the Bluetooth device active, simply press the button (5) again.INSTRUCTIONS FOR USING THE AUDIO SYSTEMNOTICE: You can only pair one Bluetooth device to the unit at a time. If the Bluetooth indicator is not blinking (indicating that it’s in pairing mode) make sure that it’s not connected to another device. If you are connected and want to pair another device, rst you must go to the settings in your Bluetooth device and turn it off allowing the Audio System to automatically search for new devices.Some unique features on the system - when playing your Bluetooth device, you can use the buttons on the controller to control your device by advancing tracks or replaying music, as well as volume. Also, by pressing the power button on the controller music on the device will pause and by pressing it again the music on the device will resume playing. When nished listening to music, simply press the power button and hold for 3-5 seconds and the Audio System will power off. If the Audio System does not sense a signal from the Bluetooth device for 10 minutes, it will automatically power itself off.1. Reset - If needed, press with a pointed object to reset controller for Bluetooth pairing2. Power - Play/Pause – Press and hold for 3-5 seconds to turn the unit on or off. Once the unit is powered on, press once for pause/play function.3. Previous Track – Go back to the previous track4. Volume Down – Decreases the sound volume.5. Bluetooth Indicator/Source Selector - Flashes blue when in pairing mode. Solid blue when successfully paired to a device. Press to select between AUX and Bluetooth input – blue light is unlit in AUX mode, solid blue in Bluetooth mode. 6. Volume Up – Increases the sound volume.7. Next Track – Skip to the next track.Warranty InformationWarranty does not cover fading or discoloration caused by exposure to sunlight or chemicals such as ammonia, household bleach, or any cleaning material that contains abrasive substances. Damage caused by accident, mishandling, improper installation, negligence, normal wear and tear, excessive water or heat damage, or products that have been altered in any way will not be covered under warranty. Use care when washing the vehicle when the Audio System is installed. Although the unit is sealed against most water or dirt intrusion, excessive pressure washing or complete submersion in water or snow is beyond the unit’s design limits and the electronic components can be damaged. This damage will not be covered under any warranty.For further information or technical support, contact Wet Sounds at 1-877-938-7757 or visit www.wetsounds.comCan-Am Audio System Instructions
FCC STATEMENT : This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. Warning: Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: Reorient or relocate the receiving an　tenna. Increase the separation between the equipment and receiver.　 Connect the equipment into an outlet on a circuit different from that to which the 　receiver is connected. Consult the dealer or an experienced radio/TV technician for help.　 FCC Radiation Exposure Statement: This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body.

Navigation menu