UNITEIC 715003672 BRP STORM Audio Kit (MY19) User Manual

Download:
Mirror Download [FCC.gov]
Document ID	3866378
Application ID	uDW94YB3MnbM6DNQetbtCQ==
Document Description	User Manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	24.27kB (303411 bits)
Date Submitted	2018-05-29 00:00:00
Date Available	2018-05-29 00:00:00
Creation Date	2018-02-21 15:45:10
Producing Software	Adobe PDF Library 15.0
Document Lastmod	2018-05-03 17:12:34
Document Title	User Manual
Document Creator	Adobe InDesign CC 13.0 (Macintosh)

Can-Am Audio System Instructions
1. Reset - If needed, press with a pointed object to reset controller for Bluetooth pairing
2. Power - Play/Pause – Press and hold for 3-5 seconds to turn the unit on or off. Once the unit is powered on, press once for pause/play function.
3. Previous Track – Go back to the previous track
4. Volume Down – Decreases the sound volume.
5. Bluetooth Indicator/Source Selector - Flashes blue when in pairing mode. Solid blue when successfully paired to a device. Press to select between
AUX and Bluetooth input – blue light is unlit in AUX mode, solid blue in Bluetooth mode.
6. Volume Up – Increases the sound volume.
7. Next Track – Skip to the next track.
INSTRUCTIONS FOR USING THE AUDIO SYSTEM
Press and hold the power button (2) for 3-5 Seconds to power the system
on. All blue lights indicate that the system is on.
The Audio System defaults to Bluetooth mode, so the Bluetooth indicator
(5) light should flash blue when powered on. If it is not lit or flashing,
press it once to re-enter BT mode. Next turn on your Bluetooth device
and search for Can-Am RST in the Bluetooth menu on your device, then
select it for pairing. Your BT device will show “connected” to the
Can-Am RST when you are successful.
To connect a device to the Auxiliary (3.5mm) input, press the Bluetooth
Indicator/Source Selector (5) once. When the blue light on this button
is unlit, this indicates that the AUX input is active and you can connect a
wired audio device with a 3.5mm male plug to the 3.5mm female jack on
the system. To make the Bluetooth device active, simply press the button
(5) again.
NOTICE: You can only pair one Bluetooth device to the unit at a time. If the Bluetooth indicator is not blinking (indicating that it’s in pairing mode) make sure that it’s not connected to another device.
If you are connected and want to pair another device, first you must go to the settings in your Bluetooth device and turn it off allowing the Audio System to automatically search for new devices.
Some unique features on the system - when playing your Bluetooth device, you can use the buttons on the controller to control your device by advancing tracks or
replaying music, as well as volume. Also, by pressing the power button on the controller music on the device will pause and by pressing it again the music on the device
will resume playing.
When finished listening to music, simply press the power button and hold for 3-5 seconds and the Audio System will power off. If the Audio System does not sense a signal
from the Bluetooth device for 10 minutes, it will automatically power itself off.
Warranty Information
Warranty does not cover fading or discoloration caused by exposure to sunlight or chemicals such as ammonia, household bleach, or any cleaning material that contains abrasive substances. Damage caused by accident,
mishandling, improper installation, negligence, normal wear and tear, excessive water or heat damage, or products that have been altered in any way will not be covered under warranty. Use care when washing the vehicle when
the Audio System is installed. Although the unit is sealed against most water or dirt intrusion, excessive pressure washing or complete submersion in water or snow is beyond the unit’s design limits and the electronic components
can be damaged. This damage will not be covered under any warranty.
For further information or technical support, contact Wet Sounds at 1-877-938-7757 or visit www.wetsounds.com
FCC STATEMENT :
This device complies with Part 15 of the FCC Rules. Operation is subject to the following
two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference that may
cause undesired operation.
Warning: Changes or modifications not expressly approved by the party responsible for
compliance could void the user's authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generates uses and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one or more of the following
measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
FCC Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environment. This equipment should be installed and operated
with minimum distance 20cm between the radiator & your body.

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.7
Linearized                      : No
Language                        : en-US
Tagged PDF                      : No
XMP Toolkit                     : Adobe XMP Core 4.2.1-c043 52.372728, 2009/01/18-15:08:04
Create Date                     : 2018:02:21 15:45:10-06:00
Metadata Date                   : 2018:05:03 17:12:34+08:00
Modify Date                     : 2018:05:03 17:12:34+08:00
Creator Tool                    : Adobe InDesign CC 13.0 (Macintosh)
Instance ID                     : uuid:ab24f039-609f-4884-b8c0-dcf8ad7223b9
Original Document ID            : xmp.did:296d6179-24cc-40b2-8912-0ab7ea1d6457
Document ID                     : xmp.id:9ebf98a9-15cc-40c2-be27-01470d00eb63
Rendition Class                 : proof:pdf
History Action                  : converted
History Parameters              : from application/x-indesign to application/pdf
History Software Agent          : Adobe InDesign CC 13.0 (Macintosh)
History Changed                 : /
History When                    : 2018:02:21 15:45:10-06:00
Derived From Instance ID        : xmp.iid:9b2158bd-6b95-48fb-b66b-92d7ff482d0b
Derived From Document ID        : xmp.did:296d6179-24cc-40b2-8912-0ab7ea1d6457
Derived From Original Document ID: xmp.did:296d6179-24cc-40b2-8912-0ab7ea1d6457
Derived From Rendition Class    : default
Format                          : application/pdf
Producer                        : Adobe PDF Library 15.0
Trapped                         : False
Page Count                      : 2
Creator                         : Adobe InDesign CC 13.0 (Macintosh)

EXIF Metadata provided by EXIF.tools