UTC Fire and Security Americas 692-PIR Security Alarm Transmitter User Manual 54883

Download:
Mirror Download [FCC.gov]
Document ID	54883
Application ID	EiudXpehvTOA+UB0HITC+Q==
Document Description	8
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	56.71kB (708900 bits)
Date Submitted	1999-08-18 00:00:00
Date Available	1998-09-09 00:00:00
Creation Date	2001-06-04 09:09:45
Producing Software	Acrobat Distiller 4.0 for Windows
Document Lastmod	2001-06-04 09:09:52
Document Title	54883.pdf
Document Author:	jsoscia

INTERACTIVE TECHNOLOGIES INCORPORATED
EXHIBIT 3
INSTALLATION AND OWNERS MANUAL
This exhibit contains applicable information on the PASSIVE INFRARED (PIR) SENSOR
TRANSMITTER , taken from the owners and installation manual.
14—21
FCC ID: B4Z-692-PIR
ITI Indoor and
Outdoor Long-Life
PIR Motion Sensors
Document Number: 4664543 Rev.C
April l998
Installation
Instructions for:
I 60-700-95R 3I9 5 MHz SAW PlR
l 60-700-95R»0D 319.5 MHz SAW Outdoor PIR
I 60-703-95 319.5 MHZ Crystal FIR
Product Summary
ihese models oflTi passive infrared (FIR) motion sensors
utilize the latest in teehnieal improvements to provide supe-
riot battery life (see "Snecifications") and improved motion
detection in harsh environments. The 60—700»95R SAW PIR
uses two AA alkaline batteries and the 60-703-95 Crystal
FIR uses one Dr two (to further increase battery hie) AA
lithium batteries.
These PIRs detect movement within a specific area by sens-
ing the infrared energy emitted from a body as it moves
across the sensor's field ofvievv.oau51ng a temperature
change in the sensor's zones. When this motion is detected.
the sensor transmits an alarm signal to the comm] panel
The indoor motion sensor can be used to protect locations
where door/Window sensors are impmctieal or not needed.
For example. use a motion sensor to protect large areas or
open floor plans. Motion sensors also provide backup pro-
tection for door/window Sensors
Use the outdoor motion sensor to identify motion in an out—
door area. Detected motion in this protected area can sound
chimes or turn on outside lights.
Do not use outdoor motion sensors for intrusion
protection.
B4Z~692~PIR
These wireless motion sensors include the following fea-
turcs’
35 feet by 40 feet coverage area for standard and
optional animal alley lenses
Masking kit provided to block portions ofcoverage
area
Three minute transmitter lockout time after an alarm
that helps extend hattery life
Cover-activated tnmper(optionsl wall-activated tamper
is included)
Supervisor) signal transmitted every 64 minutes to the
control panel
Sensor low battery reports (trouble)to the control panel
Field-selectable sensnivity options (indoor PIRs)
Indoor Motion Sensor
Installation Guidelines
Use the following guidelines for installing indoor motion
sensors
"possible, locate sensors within IOO feet ofthe panel
While a transmitter may have a range of 500 feet or
more out tn the open, the environment at the installa-
tion site can have a significant eliect on transmitter
range Sometimes a change in sensor location can help
overcome adverse wireless conditions.
The recommended mounting height is 7 1/2 feet, but
the sensor can be mounted from 5 to 8 feet high in the
comer ofthe area you want to protect. See the animal
alley lens guidelines for mounting the optional animal
alley lens. Higher mounting pmVides better range (up
to 35 feet). and lower mounting provides better protec-
tion close to the motion sensor (see Figures 2 and 3)
The optional swivel mount (lTI #60-737) can be used
for difficult mounting locations
Position the sensor to protect an area where an intruder
would be most likely to walk across the detection pat-
tern (see Figure 1)
Mount the motion sensor on an insulated, outside wall
taeing in
Mount the motion sensor on a rigid surface which is
free from vibrations.
Position the sensor so it faces a solid reference point.
like a wall.
Do not. aim the sensor at windows, fireplaces. air condi-
lioncrs. area heaters. toned air heating vents, or place
PAGE 15
Figure 3. Side view show the differences in the
coverage area when using the indoor motlon
sensor's standard lens mounted at different
heights.
Figure 4. Shows the side view of the indoor motion
sensor's animal alley lens when the flush-mount
po on is used. The outdoor motion sensor's lens
also has thls side view. however. ils swivel mount
makes the viewing angle adjustable
Mounting the Indoor Motion Sensor
The sensorcan be flush-mounled, inelinemnunted. or eur-
net-mounted dependmg on [he lens used (see Flgurc 5),
Also, the entiunul swivel muunt (1T) 460437) can be used
for drrfieult mounting locations
Figure 5. Wall Mount Options: use th n ned
position for surface or corner mounting With the
standard lens Use the flush poeition for surface or
comer mountlng with the animal alley lens. The
optional swivel mount installation in also shown.
Use the follawlng procedure to mount tlie sensor.
1. Remove the mounting plate by depressing Ihe button
on the top ofthc sensor body. Wth the oppnsile hand
pull Ihe mounting plate away from the body ofthe sen-
sot.
2. Punch out the mounting holes that best fityour applica~
lion See Figure 5 for wall mount options. See also Fig
ure 6 It) determine which knockouts in use when
mounting lhc motion sensor. Use the lower-side holes
for comer mounling. or the lower-back holes for sur»
face mounting with the standard lens.
Fur avplicallons with petsl use the upper mounting
holes and the optional animal alley lens
3. lfyou desire wall-tamper functionality, remove the
mil-tamper knockout (see Figure 6)
Note: The wall-tamper swtteh cannot be used when the
sensor is swwel or mmer mounted
PAGE 17
B4Z—692-PIR
Figure 1. Sensitivity Pins Locations
2. Locate the sensitivity pins under the battcr) on the right
slde uflhe PlR when looking at the front ofthe WK.
3. To change to high sensitivity move the shoningiumper
to the pair of pins that are closer to the top ot‘the PlR
(see Figure 7)
Note: lithe shorting jumper is not used or placed incorr
really, the sensor defaults to standard sensitivity
4. Walk test the HR to verify the sensitiviry
Walk Testing for the Indoor and Out-
door Motion Sensors
Walk testing should hi: done to determine thi: sensor‘s actual
coverage area. The edge nfthe coverage pattern is deter-
mlncd by rho first flztsh ofthe LED This may change
slightly depending upon the sensitivity setting. Walt test the
unit from both directions to determine the pattern bound-
ones.
1. Remove the sensor body from the mounted mounting
plate. activate the tamper switch. and [hen rcmnunt the
body to activate Ihc 60 sccond walk [csi modc
2. Walk across the coverage pattern to determine the cov-
erage area. indicated by LED activation. Each activa-
tion extends the walk test mode for an additional 60
seconds.
After 60 seconds wllhoul motion the vialk lest mode and the
LED will no longer aCtlvatl: when motion is detected.
Note: Excessive use of the walk test mode may reduce
battery life Use only let initial setup and mainte-
nance testing.
Note: When the walk test mode has ended. an alarm
can be transmitted only afler 3 minutes have
passed SInEE the previous alarm This 3 minute
lockout time reduces unnecessary RF transmISr
sioris in high traffic areas thereby extending bat-
tery tile
Environ merit Testing
Indoor Motion Sensors:
Turn on all heating or air conditioning sources which would
normally be active during the protection period. Stand away
from the sensor and outside the coverage paltcm and watch
(or alarms
Outdoor Motion Sensors:
Vcrll} that the scnsor’s coverage area do: not extend into
undesired areas that might cause unwanted activations.
Thcsc ztrcas may include undesired human, pet, or automo-
bile motion.
Coverage Masking
Aitcr wtilk testing and environmenttesting are completed,
misting labels czm be applied to the scnsor's lens to block
detection ofproblem areus. l‘he masking labels provided are
cut to match the corresponding lens segments.
1. Determine which detection zone/lens segment needs a
masking label,
2. Pool the desired mask label from [is backing lintl apply
to the inside urthe lens segment to be blocked.
Outdoor Motion Sensor Filter Installa-
tion:
A I inch by 1 inch piece oflens material has been included
with the outdoor motion scnsor This f'llicr reduces the sen-
sors sensitivity to white light sources (sunlight and head
lights) and infrared sources Install this filler when experi-
encing unwanlcd sensor activations due to these sources.
1. Remove the sensor from its water resistant enclosure
by sliding the front cover upward until the sensor can
be removed.
2. Remove the mounting plate oflhc sensor by depressing
the button on top ol‘the sensor.
3. Remove the from cover ofthe sensor by depressing the
two tabs on lhc top and the 0m: lab on the bottom ofthc
Scnsur body and sliding the cover ofttsce figiue 8).
4. PI ‘c the sensor on its back and drop the filter into tho
lcns chiimher covering the sensor‘s detector.
5. Replace the cover making sure thc filter remains in the
lens chamber and does not interfere with the attach-
ment of the covcr.
PAGE 19
B4Z-692-PIR
Troubleshooting
Use rhe followrng guidelines iflhc system does not respond
correctly W hen the sensor is activated,
- Check programming and rc-pmgram sensor inlo panel
irneccssary
l Move the sensor to another location and test for correct
response
To relocate a sensor-
1. Tesl iite sensor a few inches from the original position
2. increase the distance from the original position and
retest until an acceptable location is found.
3. Mount the sensor in the new location.
4. ifno incaiion is acceptable. test the sensor as described
below:
I. Test a known good sensor at the same location.
2. Ifrhe system does not respond, avoid mounting a
sensor at that location.
3. ifilie replacement sensor functions. return the prob-
lem sensor for repair or replacement.
Specifications
60-700-95R and 60-700-95R—0D SAW PIRs:
Power source: 2 AA alkaline batteries; in Part it so-
600 (six batteries per package)
Typical battery lite: 4-6 years at 68° F (not verified by
U I.)
Operating temperature range-
32° to 120° F (Indoor Motion Sensor)
lo°tn In" F (Ouldnor Motion Sensor)
FCC IDifl B4Zr692—PIR
Dimensions“ L z 2 875" X W : 2.375" X H : I.875"
60—703-95 Crystal PIR:
Power source: l or 2 AA lithium batteries. ITi Pan #
60—619(six batteries per package)
ryriieal battery life
87 to years at 68° F (with one battery . not verified
by UL.)
14-18 years at 68° F (with two batteries - not veri-
fied by U.l..)
Operating temperature range:
32° to 120° F
FCC ID# B42-693-P1R
Dlmenslons. L 2 2.375" X W 2 2.375“ X ii 2 1.875"
Notices
These dances comply wtin pm 15 oflhc rcc min. Operatinn is subtecl Iu
tire l'ollowtng Iwu eondirioits
1 these devices inn) m)! cause harmful interference.
z ‘Iheyc iitticts innsr ncczpt any interference received, ineluding mmrfe'b
enae lhzt may eante undesired operation.
Changes of modifications not expressly approvod by Inlrmcllvc chhnoln»
pres, inc can void the ltwrs' antitaniy to operate the endiptneni
PAGE 21
B4Z-692-PIR
6. Replace the sensor‘s mountlng plate and install the
sensor in its water resistant enclosure
Programming
For complete programming instructions. refer to the appro-
prtme control/Janel installation instructions General
guidelines for programming lliis sensor are
1. Set the control panel to the program made.
2. Trip the FIR by removing the FIR from its mounting
plate and activating the tamper switch
3. Exit the program mode alter all appropriate assign-
ments have been made.
4. Return the HR to its mounting plate.
Maintenance
At least once a year. the range and coverage should be veri-
fied for proper operaiion, The end user should be inslmcted
to put the sensor in walk test mode and walk through the far
end ofthe coverage pattern to verify proper detection
Replacing Batteries
_—
When battery replacement is necessary, observe proper
polarity (as Shown in the battery compartment), or the sen-
sor may be damaged. The 60-700—95R and 60r700-95 R—OD
SAW 1’le require two AA alkaline batteries and the 60-
703-95 Crystal FIR requires only one AA lithium battery
which can he placed in either battery compartment. Remove
the mounting plate and cover to reveal the battery compan-
ments shown in Figure 8 Be sure to note that as you look at
the battery compartment, on the lett side the positive side is
down and on the right side the positive end is up when the
batteries are replaced, wait at least 3 minutes afler installing
the batteries before activating the walk test mode.
PAGE 20
Figure 8. PIR Components. Battery Locations, &
Tamper Switch
Final Testing
Final testing should always be dime to verify radio signal
integrity and confirm control panel programming and
response. Guidelines for the testing are as follows.
Ii Place the control panel in Sensor test mode.
2 Remove the motion sensor from its mounting plate to
Activate the tamper switch and the sensor‘s walk test
mode,
3. Replace the sensor ln its mounting plate.
4. Walk across the sensor’s detection pattern until the
sensors LED turns on STOP your motion,
54 Listen for the appropriate system response lfthe sys»
tem does not respond and the control panel is an
UltraGard or CareTaker Plusi test the FIR by activating
its tamper switch and listening for the appropriate sys—
tem response tryou are using a diiferent control panel
that does not respond properly proceed to the "Trou-
bleshooting" section below
B4Z-692-PIR
Figure 6. FIR Mounting Plate Knockoufi
4. Mark the location ofihc required holes on the mount-
ing surface.
5. Use wall anchors and screws to secure tntn place.
Attach the sensor to the mounting plate
6. when testing is completed the PIR can be securely
attached to its mounting plate by screwing the smallest
enclosed screw into the hole al the top of the mounting
plate
Mounting the Outdoor Motion Sensor
1. Determine the desired mounting location for the sensor
leaving at least four inches of room above the wall
mount plate to attach the sensor
2. Attach the wall mount plate with the opening for the
swivel mount racing downward using the screws and
anchors supplied
3. Attach the sensor asstrmbly to the wall mount plate by
screwing the sensor assembly up into the opening in
the wall mount plate.
4. To remove the sensor for testing or battery replace-
ment. slide the front cover ofihe sensor upward until
the sensor can be removed
Indoor Motion Sensor Lens Replacement:
1. To change the lens. first remove the sensor from its
mounting plate by depressing the button on the top of
the sensor
2. Remove the cover by depressing the two tabs on the
top and the one tab on the bottom ofthe sensor body
and sliding the cover oli (see Figure St
3. Remove the installed tens by gently placing pressure
on the lens from the outside of the lens.
4. Replace with the appropriate lens by aligning us
notches with the appropriate tabs in the cover
PAGE 18
5. Install the new lens with the smooth side facing out and
the grooved side facing in
6. Replace lite cover and then replace the sensor in its
mounting plate.
Indoor Motion Sensor
Animal Alley Lens Guidelines
The optional animal alley lens (ITI 1460—709) provides pro
tection in installations where pets move about freely. See
figures 2 and 4 for coverage.
I Allowed mounting height is between 3 and 5 feet.
I Be sure to use the flush-mount position or the comer
mount position with the back ofthe PIR parallel to the
walls Do not use the inclined mount position since this
“mild tilt the FIR"; field of view downward.
I Position the sensor to have a clear line of sigh| across
the protected room.
I For best results. install the sensor higher than the high-
est point that the pet might reach in the detection urea.
I It the detection urea contains furniture or other Objects
upon which the pet could clirnh or jump. eitherremove
these objects. mount the FIR a safe distance above
these objects. or mask these areas.
Setting the Sensittvtty on the Indoor
Motion Sensor
The PIR is set to standard sensitivity at the factory. This
sensutvtiy ts preferred for most applications and provides
the best immunity to false alarms.
CAUTION: High sensitivity should only be used
In extremely quiet environmcnts
where thermal transients am not
expected,
I. Locate the sensitivity pins by first removing the
mounting plate and the sensor cover as described in
steps 1 and 2 otl.ens Replacement prceess
B42-692-P1R
n in direct sunlight. Sudden changes in Icmperalure
may triggcr a false alarm from these devices.
8. Do not mount the sensor ncar ducl work or clher large
metallic urfaces “hich may affect the RF signals (see
RF Testing) Actual acceptable Irznsmlucr range
should be verlfied for each inslflllatiun,
9. Mount lhe sensor permanently on fl {1111 wall nr in a
Comer. Du not Sci u an a shelf
10. Windows should be closed in any area which has an
armed moticn sensor
11. A pct urn trigger a motion sensor. See animnl ullcy
lens guidelines in use a motion sensor when pets are
present
Outdoor Motion Sensor
Installation Guidelines Figure 1. Overhead (Bird’s Eye View) Detection
— Pfl‘“
Use the follow ing guidelines for inslalling oulduor mulinn
sensors.
1. Always select the nutdnor motion sensor with the
weather-resistant case and me extended opcraling lem-
peralure range (1010 120° F) for ouldoor applications.
2. Do nor use nutdour motion sensors for intrusion pro»
tcction since any human, pet. or heated mechanical
motion such as an automobile can activate the sensor,
3. Follcvl Ihe indoor mo|inn sensor installation guidelines
except for items numbered 4 6. 10. and lit
4. Do not aim the sensor at objects that may be heated
excessively by the sun, such as blacktop or dark col-
ored objects
5. Do ncl aim the sensor at foliage or shrubbcry which
has n dark background
6. The housing is waler—rcslsmnt but nol waler-prnof.
Mounl the sensor undemeath eaves or porch ccvenngs
to prevent over exposure to ram, ice, and direct sun-
light.
7. The sensor's coverage area is shown in Figures 2 and Figure in“, graph shows the top view of the
4- lens coverage area, for the indoor motion sensor’s
siandard and animal alley lens and the outdoor
motion sensor's lens.
PAGE 16
B4Z-692-PlR

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.3
Linearized                      : Yes
Create Date                     : 2001:06:04 09:09:45
Producer                        : Acrobat Distiller 4.0 for Windows
Author                          : jsoscia
Title                           : 54883.pdf
Modify Date                     : 2001:06:04 09:09:52-04:00
Page Count                      : 10

EXIF Metadata provided by EXIF.tools