UTC Fire and Security Americas 983-UDWS Wireless Door-Window Sensor User Manual Micro Door Window Sensor Installation Instructions

Download:
Mirror Download [FCC.gov]
Document ID	2081091
Application ID	VVWdTnz3IYfKySeE/a+OwA==
Document Description	User Manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	8.98kB (112277 bits)
Date Submitted	2013-09-24 00:00:00
Date Available	2013-09-24 00:00:00
Creation Date	2013-07-24 08:56:04
Producing Software	Microsoft® Word 2010
Document Lastmod	2013-07-24 08:56:04
Document Title	Micro Door/Window Sensor Installation Instructions
Document Creator	Microsoft® Word 2010
Document Author:	Brian Borchardt

Micro Door/Window Sensor Installation Sheet
sensor number assignments.
Description
The Micro Door/Window Sensor is a
supervised, wireless sensor that detects the
opening and closing of doors, windows, or
drawers. The sensor and magnet are mounted
using double-sided adhesive tape or screws
(included).
When activated, the sensor transmits an open
(trip) or close (restore) signal to the panel.
These are the signals the unit provides:
supervisory, tamper and low battery (as
needed).
The sensor is powered by a replaceable 3VDC, lithium coin-cell battery.
Installation guidelines
•
•
•
•
Mounting the sensor on metal can reduce
its transmitting range. Therefore, test the
sensor from the desired location using the
dealer sensor test, before permanently
mounting it.
Mount the sensor within 100 ft. of the
panel.
Mount the sensor on the frame, and the
magnet on the door, window, or drawer. If
mounting on double doors, mount the
sensor on the least used door and the
magnet on the other door.
Mount sensors at least 5 inches above the
floor to avoid damaging them.
Programming
The following steps describe the general
guidelines for programming (learning) the
sensor into panel memory. Refer to the
specific panel’s documentation for complete
programming details.
1.
Set the panel to the program mode.
2.
Proceed to the LEARN SENSORS menu.
3.
Select the appropriate sensor group and
P/N 466-4430 • REV A.09 • 24Jul13
4.
When prompted by the
panel to trip the sensor
for learning, remove the
battery pull tab or remove
the sensor cover. The
system should
acknowledge learning
the sensor by touchpad
display and/or audio
(depending on the panel).
5.
Exit program mode.
Testing the sensor
1.
Set the panel to the sensor test mode.
2.
Take the sensor and magnet to the
desired mounting location, making sure to
line up their alignment marks with each
other.
3.
Trip the sensor by pulling the magnet
away from the sensor.
4.
Listen for the system siren beeps to
determine the appropriate response and
refer to the specific panel documentation.
Mounting the sensor
Mount the sensor after successful programming
and testing are completed, using the supplied
mounting screws for all UL installations. For nonUL installations, using the supplied double-sided
tape is optional. Note: The gap between the
sensor and magnet should be a maximum of
3/8”.
Mounting screws (UL Installations)
1.
Remove the sensor base from the sensor.
2.
Place the sensor base in desired location
and mount the base with the supplied
screws. Attach the sensor to the base.
1/2
3.
Mount the magnet into the desired
location using the supplied screw and lock
washer, making sure the alignment mark
lines up with the sensor’s.
Varta CR2032
Panasonic CR2032
Operating
temperature range
32 to 120°F (0 to 49°C)
Double-sided tape (optional for non-UL
installations)
Storage temperature
range
-30 to 140°F (-34 to 60°C)
Relative humidity
0-85% non-condensing
1.
Dimensions
(L x W x D)
1.9 x 1.0 x 0.50 in. (4.7 x 2.5 x
1.3 cm)
Before applying double-sided tape,
ensure that the desired location is a
smooth, clean and dry surface.
Note: When applying the double-sided
tape, evenly apply pressure to ensure a
good surface contact.
2.
3.
Apply double-sided tape to the bottom of
the sensor and the magnet. Mount the
sensor and magnet at the desired
locations, ensuring the alignment marks
line up with each other.
Regulatory information
Manufacturer
UTC Fire & Security Americas
Corporation, Inc.
1275 Red Fox Rd., Arden Hills, MN
55112-6943, USA
FCC
compliance
This device complies with part 15 of
the FCC Rules. Operation is subject to
the following two conditions: (1) This
device may not cause harmful
interference, and (2) this device must
accept any interference received,
including interference that may cause
undesired operation.
FCC ID: B4Z-983-UDWS
IC: 1175C-983UDWS
Retest the sensor using the procedure in
the section “Testing the Sensor”.
For additional tamper security
1.
2.
This Class B digital apparatus
complies with Canadian ICES-003.
Punch out the seal covering the screw
hole on the sensor cover.
With the sensor base secured to the
sensor, insert the smallest screw
supplied, securing the sensor base to the
sensor.
Cet appareil numérique de la classe B
est conforme à la norme NMB-003 du
Canada.
UL
UL 1023 – Household Burglar-Alarm
System Units.
Replacing the battery
1.
Remove the sensor from the base then
remove the inner cover, exposing the
battery.
2.
Remove the bad battery and install the
new battery. NOTE: Observe polarity of
the battery.
3.
Re-install the PC board, inner cover and
the sensor.
Specifications
ANSI/UL 634 Connectors and
Switches for Use with Burglar-Alarm
Systems
ULC
C634-M1986 - Connectors and
Switches for Use with Burglar-Alarm
Systems
Contact information
For contact information, see
www.utcfireandsecurity.com,
www.interlogix.com or call +1 855 286 8889.
Trademark/Copyright
Model no.
TX-1012-01-1 (white)
TX-1012-01-3 (brown)
© 2013 UTC Fire & Security Americas
RF frequency
319.5 MHz
Corporation, Inc. Interlogix is part of UTC
Compatibility
Interlogix Learn Mode Panels
and Receivers
Climate Controls & Security, a unit of United
Battery type
3-VDC, lithium coin-cell battery
UL Approved Battery
Duracell DL2032
2/2
Technologies Corporation. All rights reserved.
Micro Door/Window Sensor Installation Instructions

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.5
Linearized                      : No
Page Count                      : 2
Language                        : en-US
Tagged PDF                      : Yes
Title                           : Micro Door/Window Sensor Installation Instructions
Author                          : Brian Borchardt
Subject                         : Micro Door/Window Sensor
Creator                         : Microsoft® Word 2010
Create Date                     : 2013:07:24 08:56:04-05:00
Modify Date                     : 2013:07:24 08:56:04-05:00
Producer                        : Microsoft® Word 2010

EXIF Metadata provided by EXIF.tools