Ubee Interactive DVW2100 BCM3379 Wireless eMTA For Modular:802.11b/g/n WLAN User Manual

Ubee Interactive Corp. BCM3379 Wireless eMTA For Modular:802.11b/g/n WLAN

user manual

COMPANY CONFIDENTIAL Product Specification Hardware Specification Standards IEEE 802.11b/g/n Operating Frequency USA: 2.400 ~ 2.4835 GHz Europe: 2.400 ~ 2.4835 GHz Japan: 2.400 ~ 2.497 GHz Host Interfaces PCI Express 1.1 Operation Voltage 3.3V +/- 10% Data Rate 802.11b: 1, 2, 5.5 and 11Mbps 802.11g: 6, 9, 12, 18, 24, 36, 48, 54Mbps. 802.11n: 20 MHz BW: 150, 130, 117, 104, 78 * 40 MHz BW: 300, 270, 243, 216, 162, 108 * *Many other data rates are supported by the hardware Modulation Schemes DSSS with DBPSK, DQPSK, CCK OFDM with BPSK, QPSK, 16QAM, 64QAM MAC Protocol CSMA/CA with ACK architecture 32-bit MAC Operating Channels 11 for North America, 13 for Europe, 14 for Japan Antenna Connectors Two antennas allowing transmission or reception on both, simultaneously. Transmitter Output Power CCK 18.0 dBm Legacy OFDM 20MHz SISO 15.5 dBm Legacy OFDM 20MHz CDD 15.5 dBm MCS 0-7 20MHz SISO 15.5 dBm MCS 8-15 20MHz SDM 15.5 dBm Legacy OFDM 40MHz SISO 14.5 dBm Legacy OFDM 40MHz CDD 14.5 dBm MCS 0-7 40MHz SISO 14.5 dBm MCS 8-15 40MHz SDM 14.5 dBm MCS 32 14.5 dBm *Note: this target power means single chain Product Name: BCM3379 Wireless eMTA For Modular:802.11b/g/n WLANModel Number: DVW2100
COMPANY CONFIDENTIAL WLAN Receiver Sensitivity Mode Data Rate Minimum Sensitivity (dBm) 802.11 b 1 Mbps 94 802.11 b 11 Mbps 88 802.11 g 6 Mbps 88 802.11 g 54 Mbps 73 802.11 n HT20 MCS 0 86 802.11 n HT20 MCS 7 69 802.11 n HT20 MCS 15 67 802.11 n HT40 MCS 0 85 802.11 n HT40 MCS 7 67 802.11 n HT40 MCS 15 65 * This is draft and will be modified according to Broadcom final specification. Current Consumption ASPM L0 (normal) ASPM L1 (power saving)Test status Current (mA) Power (W) Current (mA) Power (W)Module Disable 72 0.24 72 0.24 Idle(unassociated) 97 0.32 72 0.24 Idle(associated) 121 0.40 95 0.31 Search (only for scan AP) 272 0.90 246 0.81 Transmit (max throughput) 740 2.44 740 2.44 Receive (max throughput) 650 2.15 650 2.15 S3/S4 (Standby/Hibernate) 22 0.0726 22 0.0726 *Note: this power consumption means only typical value. Product Name: BCM3379 Wireless eMTA For Modular:802.11b/g/n WLANModel Number: DVW2100
FCC Notice This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures: - Reorient or relocate the receiving antenna. - Increase the separation between the equipment and receiver. - Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. - Consult the dealer or an experienced radio/TV technician for help. THE MANUFACTURER IS NOT RESPONSIBLE FOR ANY RADIO OR TV INTERFERENCE CAUSED BY UNAUTHORIZED MODIFICATIONS TO THIS EQUIPMENT. SUCH MODIFICATIONS COULD VOID THE USER’S AUTHORITY TO OPERATE THE EQUIPMENT. To comply with FCC RF exposure compliance requirements, a separation distance of at least 20 cm must be maintained between the antenna of this device and all persons. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. Only the type of diople antenna tested may be used. The end product must carry a label stating "Contains FCC ID:XCNDVW2100".

Navigation menu