Ubee Interactive DVW32H Wiresless EMTA and WLCM User Manual 3030481

Ubee Interactive Corp. Wiresless EMTA and WLCM 3030481

User manual_rev 2.pdf

Ubee Interactive — www.ubeeinteractive.com 1 Ubee DVW32H – Safety and Installation Product Insert v1.1 DVW32H Advanced Wireless Voice Gateway Safety and Installation Product Insert Federal Communications Commission (FCC) Interference Statement This device has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This device generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this device does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures: • Reorient or relocate the receiving antenna. • Increase the separation between the equipment and receiver. • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. • Consult the dealer or an experienced radio/TV technician for help. FCC Regulatory Information This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. There is one statement for this product:
Ubee Interactive — www.ubeeinteractive.com 2 Ubee DVW32H – Safety and Installation Product Insert v1.1 • The device must carry a label stating “FCC ID: XCNDVW32H.” FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this device. IEEE 802.11b or 802.11g operation of this device in the U.S.A. is firmware-limited to channels 1 through 11. FCC Radiation Exposure Statement: This device complies with FCC radiation exposure limits set forth for an uncontrolled environment. This device should be installed and operated at a minimum distance of 20cm between itself and your body. This device must not be co-located or operating in conjunction with any other antenna or transmitter. Safety Notices Read these instructions carefully before operating the device. It is important to be aware of these safety instructions. Install the device according to these instructions and keep this guide for future reference. 1. Do not use this device in a humid space, in the rain, or near splashing water. 2. Do not install during thunder or lightening storms. 3. Do not cover any ventilation openings in the device case. 4. Do not place the device near heat sources such as radiators or stoves. 5. Clean the device only with a clean, dry cloth. Do not use liquid or chemical cleaners. 6. Avoid static discharge when touching
Ubee Interactive — www.ubeeinteractive.com 3 Ubee DVW32H – Safety and Installation Product Insert v1.1 the device by first touching the coaxial connector of the coaxial cable. 7. Installation of the device should include grounding the coaxial cable to the earth at the building entrance per ANSI/NFPA 70 and the National Electrical Code (NEC, in particular, Section 820.93, Grounding of the Outer Conductive Shield of a Coaxial Cable). 8. The device is designed for IT power systems with phase-to-phase voltage at 100-240V. 9. Disconnecting the Device: If the device becomes damaged or encounters some other abnormality, disconnect the power plug from the AC wall outlet immediately. 10. The device should be installed in a location not to exceed the maximum temperature of 40 degrees Celsius (104 degrees Fahrenheit). 11. When the device is placed upright with the aid of the stand, the stand must be fixed at a 90 degree angle to the device. Otherwise, the device will have the risk of tipping over. This is the recommended position for best Wi-Fi performance 12. Keep the device away from Children and Pets 13. Place the device on a cool surface. Failure to do so may result in overheating which can cause extreme damage. 14. Do not modify or attempt to disassemble the device. Use it only according to the instructions. 15. Do not dispose of the device in a trash container. Please recycle.
Ubee Interactive — www.ubeeinteractive.com 4 Ubee DVW32H – Safety and Installation Product Insert v1.1 Installation To install this device, follow the procedures below and refer to the following page for a connection diagram. 1. Connect one end of a coaxial cable (not included) to the CABLE port on the device. Connect the other end to a cable splitter or the cable wall outlet. Be sure not to bend or over tighten the cables as this may strain the connector and cause damage. If you plan to connect the device and a television to the same cable wall outlet, you must use a cable line splitter (not included). 2. Connect one end of the supplied Ethernet cable to one of the LAN ports (LAN1 to LAN4) on the device. Connect the other end to the ETHERNET port (ETH1 to ETH4) on a PC. Note: Category 5e or Category 6 Ethernet cables with RJ45 connectors must be used when connecting Ethernet devices to the LAN ports. This ensures Gigabit Ethernet speeds (unless the computer does not support it). 3. Connect one end of an RJ11 phone cable to one of the TEL ports (TEL1 to TEL2) on the device (a port that has been provisioned for voice service as specified by the service provider). Connect the other end to the phone port of the telephone. Note: If voice service is not provisioned through the service provider, telephone service is not available. 4. Connect the power adapter to the POWER port on the device. Plug the other end of the power adapter into the AC wall outlet. Important: Use only the power adapter that is shipped with the device.
Ubee Interactive — www.ubeeinteractive.com 5 Ubee DVW32H – Safety and Installation Product Insert v1.1 Wall-Mount Installation You can mount the device on a wall using the 2 mounting brackets on the bottom of the device. We recommend that you use two round or pan head screws. 1. Install two screws horizontally apart on a wall using the measurement shown to the right. The screws should protrude from the wall so that you can fit the device between the head of the screw and the wall. If you install the screws in drywall, use hollow wall anchors to ensure that the unit does not pull away from the wall due to prolonged strain from the cable and power connectors. 2. Remove the device from the product package. 3. Mount the device on the wall. 4. Refer to the following figure. The Distance of the Pothook (Horizontal) The Screw’s Size (mm) 88mm (3.46 inches)
Ubee Interactive — www.ubeeinteractive.com 6 Ubee DVW32H – Safety and Installation Product Insert v1.1 Additional Information 1. RESET Button: To reset the device to factory defaults. Using a pointed object, insert it into the button opening, and hold for more than 10 seconds. The device will reset and reboot. Note: Not all parameters are reset to factory defaults. Refer to the User Guide for more information. 2. WPS button: The WPS button located on the front of the Device, The Wi-Fi Protected Setup method used to connect a PIN protected Wi-Fi device to this Device. LEDs and Other Device Indicators See the following diagram and descriptions of the device’s LED behavior, and the behavior of the back-panel Ethernet indicators. LED Indicators (Color = Green When On): POWER/ READY—(POWER, Green) If On, indicates that the device has successfully completed internal power-on tests. LED flashes if power-on fails. (READY, Blue) When the device is obtaining an IP address and configuration file, the LED flashes. When successfully complete, the LED is On. DS/US—LED flashes once every second while scanning downstream, once locked, flashes twice every second while scanning upstream, solid when online. When the device performs a firmware upgrade, the LED flashes. When channel bonding, LED should be Blue otherwise green. Tel 1/Tel 2—The LED is On when a telephone is on-hook. The LED flashes when a telephone is off-hook. Wi-Fi—The LED is on (Solid Green) when enabled and blinking (green) when data is been passed between the Device and the connected
Ubee Interactive — www.ubeeinteractive.com 7 Ubee DVW32H – Safety and Installation Product Insert v1.1 laptop, computer, etc. WPS LED— When a user pushes the WPS button or triggers WPS via the device’s web GUI, this LED on the front of the device flashes Green for 2 minutes until a PIN is entered from a wireless client wishing to connect (e.g. a laptop computer). After a Wi-Fi client attaches successfully, the LED remains On (green) for 5 minutes, then turns Off. LAN1/LAN2/LAN3/LAN4—The Ethernet ports are used to connect Ethernet devices, such as computers, gaming consoles, and/or routers/hubs to the Device using RJ45 cables. Each Ethernet port has an LED to indicate their statuses when an Ethernet device is connected. When an Ethernet device, is connected to the cable modem, the LED is Green when connected at 10/100 Mbps speeds. The LED is Blue when connected at 1000 (Gigabit Ethernet) speed. When data is being passed between the Device and the connected laptop, computer, etc, the LED flashes with same color scheme (i.e. green for 10/100Mbps or blue for Gigabit).

Navigation menu