Ubiqconn Technology GN01 Snap-on module User Manual 2IN1 UG 2013

Download:
Mirror Download [FCC.gov]
Document ID	2173630
Application ID	rov62f7HeXEis4OcZrxm8g==
Document Description	(SN201-GN01) UserMan
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	19.68kB (246022 bits)
Date Submitted	2014-01-23 00:00:00
Date Available	2014-01-24 00:00:00
Creation Date	2014-01-08 16:03:38
Producing Software	PDF Printer / www.bullzip.com / CP / Freeware Edition
Document Lastmod	2014-01-08 16:03:38
Document Title	Microsoft Word - 2IN1 UG 2013.doc
Document Author:	JAY_WU

2-IN-1 Snap On module
UG
2 - ININ - 1SNAP ON MODULE User Guid
FCC Compliance Statement
This device complies with Part 15 of the FCC Rules. Operation is subject
to the following two conditions: (1) this device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
This equipment generates uses and can radiate radio frequency energy
and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. However, there is
no guarantee that interference will not occur in a particular installation. If
this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on,
the user is encouraged to try to correct the interference by one or more
of the following measures:
-- Reorient or relocate the receiving antenna.
-- Increase the separation between the equipment and receiver.
-- Connect the equipment into an outlet on a circuit different from
that to which the receiver is connected.
-- Consult the dealer or an experienced radio/TV technician for
help.
FCC Caution: Any changes or modifications not expressly approved by the
party responsible for compliance could void the user's authority to operate
this equipment.
2 - ININ - 1SNAP ON MODULE User Guid
Europe – EU Declaration of Conformity
This device complies with the essential requirements of the
R&TTE Directive 1999/5/EC and EMC directive 2004/108/EC. The
following test methods have been applied in order to prove
presumption of conformity with the essential requirements of the
R&TTE Directive 1999/5/EC and EMC directive 2004/108/EC:
EN 55022: 2010 + AC: 2011
EN 61000-3-2 : 2006 + A2 2009
EN 61000-3-3 : 2008
EN 55024: 2010
(IEC 61000-4-2: 2008;
IEC 61000-4-3: 2010;
IEC 61000-4-4: 2012;
IEC 61000-4-5: 2005;
IEC 61000-4-6: 2008;
IEC 61000-4-8: 2009;
IEC 61000-4-11: 2004)
< EN 60950-1: 2005 + A1
Safety of information technology equipment
< EN 300 328 V1.7.1: 2006
< EN 302 291 -1/ -2
< EN 62311: 2008
2 - ININ - 1SNAP ON MODULE User Guid
Specification
The 2-IN-1SNAP ON MODULE is a flexible, With following specifications
that can be applied in diverse operational environments and implemented
in multi-faceted applications.
Barcode Scanner :
Decoded Mode :
1D Symbologies : EAN/UPC, RSS, Code 39, Code 128,
UCC/EAN 128, ISBN, ISBT, Interleaved, Matrix, Industrial
and Standard 2 of 5, Codabar, Code 93/93i, Code 11, MSI,
Plessey, Telepen, postal codes.
2D Symbologies: Data Matrix, PDF417, Micro PDF 417,
Maxicode, QR, Aztec, EAN.UCC composite.
GPS :
Channel :
50 channel all-in-view tracking
GPS,GLONASS support
1 x Signal Color LED (Blue)
CAC :
Supports ISO/IEC 7816 standard
Supports PC Smart Card industry standard: PC/SC 1.0 & 2.0
Works with 5V, 3V and 1.8V Smart cards
2 - ININ - 1SNAP ON MODULE User Guid
GPS :
'- ISO/IEC 14443A, 14443B, 15693
- Mifare 1K/4K, Ultralight
- NFC-IP1 Protocol
2 - ININ - 1SNAP ON MODULE User Guid
Using a Barcode Scanner /GPS Module
The System provides barcode scanner/GPS functions for your optional
selection, before installing either of these two modules on the top side of
the system, please remove the screws previously (illustrated in the
following graphics as indicated step 1).
To install the Barcode Scanner/GPS Module:
1. Make sure the system is turned off. Unscrew four screws from the
accessory door on top of the system.
2. Mount and secure the Barcode daughter board into the
mainboard with screws.
2 - ININ - 1SNAP ON MODULE User Guid
3. Insert FFC cable of barcode scanner into connector slot or
attached the GPS cable to the connectors on the daughter
board.
4. Screw to secure the Barcode Scanner/GPS onto the tablet.
GPS:
1). Set baud rate to 9600bps
2). Connect to GPS module via appropriate serial port#
→ For GP01 (on main tablet unit): please check under device
manager under COM&LPT ports, choose the Enhanced
2 - ININ - 1SNAP ON MODULE User Guid
COM port# corresponding to 1st set of "Silicon Labs Dual CP210x
USB to UART Bridge: “Enhanced” COM Port
(COMx)
Using a NFC /GPS Module
The System provides NFC/GPS functions for your optional selection,
before installing either of these two modules on the top side of the system,
please remove the screws previously (illustrated in the following graphics
as indicated step 1).
To install the NFC/GPS Module:
2 - ININ - 1SNAP ON MODULE User Guid
5. Make sure the system is turned off. Unscrew four screws from the
accessory door on top of the system.
6. Mount and secure the Daughter board into the mainboard
with screws.
7. Insert FFC cable of barcode scanner into connector slot or
attached the NFC/GPS cable to the connectors on the daughter
board.
8. Screw to secure the NFC/GPS onto the tablet.
9. The RFID read range of this module will vary from
approximately 40 ~50mm depending on the following factors;
2 - ININ - 1SNAP ON MODULE User Guid
9.1. The shape and size of the RFID tag. Large Size RFID tags have
longer read range (Smaller tags have a smaller RF
radiating field)
9.2. Any metallic objects near the RFID tag will effectively reduce
the read range
9.3. Any electrical interference from surrounding electrical
equipment may reduce read range.
Using a CAC /GPS Module
The System provides CAC/GPS functions for your optional selection,
before installing either of these two modules on the top side of the system,
please remove the screws previously (illustrated in the following graphics
as indicated step 1).
To install the CAC/GPS Module:
10
2 - ININ - 1SNAP ON MODULE User Guid
9. Make sure the system is turned off. Unscrew four screws from the
accessory door on top of the system.
10. Mount and secure the Daughter board into the mainboard
with screws.
11. Insert FFC cable of barcode scanner into connector slot or
attached the CAC/GPS cable to the connectors on the daughter
board.
12. Screw to secure the CAC/GPS onto the tablet.
11

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.5
Linearized                      : No
Page Count                      : 11
XMP Toolkit                     : XMP toolkit 2.9.1-13, framework 1.6
About                           : uuid:e10e3be2-7a96-11e3-0000-8bcc10301680
Producer                        : PDF Printer / www.bullzip.com / CP / Freeware Edition
Modify Date                     : 2014:01:08 16:03:38+08:00
Create Date                     : 2014:01:08 16:03:38+08:00
Creator Tool                    : UnknownApplication
Document ID                     : uuid:e10e3be2-7a96-11e3-0000-8bcc10301680
Format                          : application/pdf
Title                           : Microsoft Word - 2IN1 UG 2013.doc
Creator                         : JAY_WU
Author                          : JAY_WU

EXIF Metadata provided by EXIF.tools