Ubiquiti LBE5AC Access Point User Manual LiteBeam LBE 5AC 23 Quick Start Guide

Ubiquiti Networks, Inc. Access Point LiteBeam LBE 5AC 23 Quick Start Guide

Manual 2

6.  Press both sides of the Port Cover and detach it from the Feed Receiver.7.  Connect an Ethernet cable to the Ethernet port.
8.  Reattach the Port Cover.9.  Open the Metal Strap and feed it through the two slots of the Ball Joint Mount.
10. Wrap the Metal Strap around the pole. Use a 7 mm socket wrench or screwdriver to turn the screw clockwise and securely fasten the strap to the pole.11. Loosen the lock nut on the Ball Joint Mount, and aim at the other end of the wireless link. Use the bubble level to ensure level alignment, and then lock the aim by hand‑tightening the lock nut.
Connecting Power over Ethernet1.  Connect the Ethernet cable from the Ethernet port of the LiteBeam ac to the adapter’s POE port.2.  Connect an Ethernet cable from your LAN to the adapter’s LAN port. 3.  Connect the Power Cord to the adapter’s power port. Connect the other end of the Power Cord to a power outlet.Mounting the PoE Adapter (Optional)1.  Remove the PoE Mounting Bracket from the adapter, place the bracket at the desired location, and mark the two holes. 2.  Pre‑drill the holes if necessary, and secure the bracket using two fasteners (not included).3.  Align the adapter’s slots with the tabs of the PoE Mounting Bracket, and then slide the adapterdown.
Accessing airOS®1.  Make sure that your host system is connected via Ethernet to the LiteBeam ac. 2.  Configure the Ethernet adapter on your host system with a static IP address on the 192.168.1.x subnet.3.  Launch your web browser. Type https://192.168.1.20 in the address field. Press enter (PC) or return (Mac). 4.  The login screen will appear. Enter ubnt in the Username and Password fields. Select your Country and Language. You must agree to the Terms of Use to use the product. Click Login.Note: For the Country setting, U.S. product versions are restricted to a choice of Canada, Puerto Rico, or the U.S. to ensure compliance with FCC/IC regulations. The airOS Configuration Interface will appear, allowing you to customize your settings as needed.*640-00218-01*640-00218-01
Installer Compliance ResponsibilityDevices must be professionally installed and it is the professional installer's responsibility to make sure the device is operated within local country regulatory requirements.Since Ubiquiti Networks equipment can be paired with a variety of antennas and cables, the Antenna Gain and Output Power fields are provided to the professional installer to assist in meeting regulatory requirements.
SpecificationsLBE‑5AC‑23Dimensions 362 x 273 x 203 mm (14.25 x 10.75 x 7.99")Weight 907 g (2.00 lb)Operating Frequency Worldwide: 5150 ‑ 5875 MHz USA: 5150 ‑ 5350, 5470 ‑ 5850 MHzNetworking Interface (1) 10/100/1000 Ethernet PortAntenna Gain 23 dBiMax. Power Output 25 dBmMax. Power Consumption 7WPower Supply 24V, 0.3A Gigabit PoE Adapter (Included)Power Method Passive PoE (Pairs 4, 5+; 7, 8 Return)Operating Temperature ‑40 to 70° C (‑40 to 158° F)Operating Humidity 5 to 95% NoncondensingESD/EMP Protection ± 24 kV Contact / Air Shock and Vibrations ETSI300‑019‑1.4Certications CE, FCC, ICWind Survivability 200 km/h (125 mph)Wind Loading 87 N @ 200 km/h (19.5 lbf @ 125 mph)
Safety Notices1.  Read, follow, and keep these instructions.2.  Heed all warnings.3.  Only use attachments/accessories specified by the manufacturer.WARNING: Do not use this product in location that can be submerged by water. WARNING: Avoid using this product during an electrical storm. There may be a remote risk of electric shock from lightning. Electrical Safety Information1.  Compliance is required with respect to voltage, frequency, and current requirements indicated on the manufacturer’s label. Connection to a different power source than those specified may result in improper operation, damage to the equipment or pose a fire hazard if the limitations are not followed.2.  There are no operator serviceable parts inside this equipment. Service should be provided only by a qualified service technician.3.  This equipment is provided with a detachable power cord which has an integral safety ground wire intended for connection to a grounded safety outlet.a.  Do not substitute the power cord with one that is not the provided approved type. Never use an adapter plug to connect to a 2‑wire outlet as this will defeat the continuity of the grounding wire. b.  The equipment requires the use of the ground wire as a part of the safety certification, modification or misuse can provide a shock hazard that can result in serious injury or death.c.  Contact a qualified electrician or the manufacturer if there are questions about the installation prior to connecting the equipment.d.  Protective earthing is provided by Listed AC adapter. Building installation shall provide appropriate short‑circuit backup protection.e.  Protective bonding must be installed in accordance with local national wiring rules and regulations.
Limited WarrantyUBIQUITI NETWORKS, Inc (“UBIQUITI NETWORKS”) warrants that the product(s) furnished hereunder (the “Product(s)”) shall be free from defects in material and workmanship for a period of one (1) year from the date of shipment by UBIQUITI NETWORKS under normal use and operation. UBIQUITI NETWORKS’ sole and exclusive obligation and liability under the foregoing warranty shall be for UBIQUITI NETWORKS, at its discretion, to repair or replace any Product that fails to conform to the above warranty during the above warranty period. The expense of removal and reinstallation of any Product is not included in this warranty. The warranty period of any repaired or replaced Product shall not extend beyond its original term. Warranty ConditionsThe above warranty does not apply if the Product:(I)  has been modified and/or altered, or an addition made thereto, except by Ubiquiti Networks, or Ubiquiti Networks’ authorized representatives, or as approved by Ubiquiti Networks in writing;(II)  has been painted, rebranded or physically modified in any way;(III)  has been damaged due to errors or defects in cabling;(IV)  has been subjected to misuse, abuse, negligence, abnormal physical, electromagnetic or electrical stress, including lightning strikes, or accident;(V)  has been damaged or impaired as a result of using third party firmware;(VI)  has no original Ubiquiti MAC label, or is missing any other original Ubiquiti label(s); or(VII)  has not been received by Ubiquiti within 30 days of issuance of the RMA.In addition, the above warranty shall apply only if: the product has been properly installed and used at all times in accordance, and in all material respects, with the applicable Product documentation; all Ethernet cabling runs use CAT5 (or above), and for outdoor installations, shielded Ethernet cabling is used, and for indoor installations, indoor cabling requirements are followed.

Navigation menu