Ubiquiti UAPM 802.11 b/g/n 1x2 MIMO NETWORKING DEVICE User Manual UniFi AP Mini User Guide
Ubiquiti Networks, Inc. 802.11 b/g/n 1x2 MIMO NETWORKING DEVICE UniFi AP Mini User Guide
Ubiquiti >
User Manual
| Download: |  |
| Mirror Download [FCC.gov] | |
| Document ID | 1594016 |
| Application ID | 6n2HzPNeAJXJNTeuejW16g== |
| Document Description | User Manual |
| Short Term Confidential | No |
| Permanent Confidential | No |
| Supercede | No |
| Document Type | User Manual |
| Display Format | Adobe Acrobat PDF - pdf |
| Filesize | 466.68kB (5833461 bits) |
| Date Submitted | 2011-12-02 00:00:00 |
| Date Available | 2011-12-02 00:00:00 |
| Creation Date | 2011-11-28 10:03:09 |
| Producing Software | Adobe PDF Library 9.9 |
| Document Lastmod | 2011-11-28 10:04:01 |
| Document Title | UniFi AP-Mini User Guide |
| Document Creator | Adobe InDesign CS5.5 (7.5.2) |
| Document Author: | J Lee |
Enterprise WiFi System Model: UAP-Mini UniFi™ AP-Mini User Guide Table of Contents Table of Contents Chapter 1: Product Overview. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Package Contents. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 System Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Network Topology Requirements. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Front. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Back . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Chapter 2: Installation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Hardware Installation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Software Installation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Chapter 3: Using the UniFi Controller Software. . . . . . . . . . . . . . . . . . . . . . 7 Interface Tabs. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Common Interface Options. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Recent Events. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Settings. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Admin . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 Chapter 4: Map Tab. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 Adding Custom Maps. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13 Adding a Google Map. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 Placing Access Points on the Map. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17 Setting the Map Scale . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19 Chapter 5: Statistics Tab. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20 Clients . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20 Quick Look. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20 Current Usage - Top Access Points . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21 Recent Activities. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21 Chapter 6: Access Points Tab. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22 Chapter 7: Users Tab. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23 Chapter 8: Guests Tab . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24 Chapter 9: Offline Clients Tab. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25 Chapter 10: Access Point Details. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26 Details . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26 Users . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27 Guests . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28 Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28 Ubiquiti Networks, Inc. UniFi™ AP-Mini User Guide Table of Contents Chapter 11: User/Guest Details. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34 Details . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34 Statistics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34 History. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35 Configuration. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35 Chapter 12: Hotspot Manager. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36 Appendix A: Portal Customization. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38 Overview. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38 Enabling Portal Customization. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38 Viewing the Default Portal. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38 Setup. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38 Appendix B: UniFi Discovery Utility. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40 Overview. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40 Appendix C: Specifications. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42 Appendix D: Safety Notices. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43 Electrical Safety Information. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43 Appendix E: Warranty. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44 General Warranty. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44 Appendix F: Compliance Information. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45 Installer Compliance Responsibility. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45 FCC. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45 Industry Canada. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45 RF Exposure Warning. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45 CE Marking. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45 RoHS/WEEE Compliance Statement. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46 Appendix G: Declaration of Conformity. . . . . . . . . . . . . . . . . . . . . . . . . . . . 47 Appendix H: Contact Information. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48 Ubiquiti Networks Support. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48 Ubiquiti Networks, Inc. ii UniFi™ AP-Mini User Guide Chapter 1: Product Overview Chapter 1: Product Overview Thank you for purchasing the Ubiquiti UniFi AP-Mini. The UniFi AP-Mini also works with the UniFi AP, AP-LR, and AP‑Outdoor. The UniFi AP-Mini includes the UniFi Controller software that allows you to manage your wireless network using your Web browser. This User Guide is for use with the UniFi AP-Mini and version 2.0 or above of the UniFi Controller software. The UniFi AP-Mini also includes the necessary hardware for mounting the unit on a wall or a ceiling. The UniFi AP‑Mini supports Passive PoE, which works with the included PoE adapter. If you want to power the UniFi AP-Mini from an 802.3af compliant switch, Ubiquiti Networks offers the optional Instant 802.3af Adapter to instantly transform any PoE device into a fully 48V 802.3af compliant product. Product details are available on our website at http://ubnt.com/8023af Network Topology Requirements • A DHCP-enabled network (for the wired Access Point to obtain an IP address as well as for the wireless Access Points after the deployment). • Access Point(s) and either an on-site management station computer running the UniFi Controller software connected to the same Layer-2 network or located in an off-site cloud or NOC. Wireless Uplinked1 UAP-Mini Wired UAP-Mini Package Contents Router or UniFi AP-Mini Mounting Bracket UniFi Controller CD with User Guide On-Site Management Station Off-Site Cloud/NOC2 Sample Network Topology 1 Please refer to “Wireless Uplinks” on page 31 for setting up Wireless-Linked APs. 2 All UniFi APs support Off-Site Management Controllers. Enterprise WiFi System Quick Start Guide M4 Keps Nut (Qty. 3) 5V/2A PoE Adapter M4x12 Washer (Qty. 3) Power Cord M4x50 Flat Head Screw (Qty. 3) M3.9x20 Self Tapping Screw (Qty. 3) M4x20 Screw Anchor (Qty. 3) System Requirements • Microsoft Windows XP, Windows Vista, Windows 7, or Mac OS X • Java Runtime Environment 1.6 (or above) • Web Browser: Mozilla Firefox, Google Chrome, or Microsoft Internet Explorer 8 (or above) Ubiquiti Networks, Inc. UniFi™ AP-Mini User Guide Front Chapter 1: Product Overview Back Ethernet Port Connects to the 5V PoE Adapter to provide power to the unit. Reset Button The reset button serves two functions: • Restart It will restart the device when you press and release it quickly. • Restore Factory Defaults When you press and hold it for more then 5 seconds, it will restore the device to the factory default settings. LED Indicates the status of the device. See the table below for details. LED Color Status Flashing Amber Initializing Steady Amber Factory default, waiting to be integrated Alternating Amber/Green Device is busy; do not touch or unplug it. This usually indicates a process such as a firmware upgrade is taking place. This is used to locate an AP. Quickly Flashing When you click Locate in the UniFi Controller software, the AP will flash. It will Green also display the location of the AP on the map. Steady Green Indicates the device has been successfully integrated into a network and is working properly. Steady Green with occasional flashing Indicates the device is in an isolated state (all WLANs are brought down until an uplink is found). Ubiquiti Networks, Inc. UniFi™ AP-Mini User Guide Chapter 2: Installation Hardware Installation The UniFi AP-Mini is powered by the included PoE (Power over Ethernet) adapter. To install the AP, perform the following steps: 1. Connect an Ethernet cable to the Ethernet port on the UniFi AP-Mini. Chapter 2: Installation Mounting the Access Point The UniFi AP-Mini can be wall mounted or mounted on a ceiling. Perform the following steps for the appropriate installation: Wall-Mount 1. Position the Mounting Bracket at the desired location on the wall. Orient the mounting plate with the arrow facing up. 2. Use a pencil to mark the three holes on the wall. 2. Connect the other end of the Ethernet cable to the Ethernet port on the PoE Adapter. 3. Use a 6 mm drill bit to drill the holes in the wall. 4. Insert the three screw anchors into the wall. 5. Secure the Mounting Bracket to the wall by inserting the self tapping screws into the anchors. Note: If you plan to mount the AP on the ceiling, perform the ceiling mount installation steps before connecting the Ethernet cable to the PoE Adapter. 3. Connect the PoE Adapter to your router or switch and connect the power adapter to a power outlet. Ubiquiti Networks, Inc. 6. Align the two notches on the AP with the notches on the Mounting Bracket. UniFi™ AP-Mini User Guide 7. Turn the AP clockwise until it locks into place. Chapter 2: Installation 6. Secure the Mounting Bracket to the ceiling tile by feeding the three flathead screws through the ceiling tile. Support the Mounting Bracket with the washers and Keps nuts on the top side of the ceiling tile. 8. Rotate the center logo to the desired position. Ceiling-Mount 7. Feed the Ethernet cable through the hole in the Mounting Bracket and ceiling tile. 1. Remove the ceiling tile. 2. Position the Mounting Bracket in the center of the ceiling tile. 3. Use a pencil to mark the three holes on the ceiling tile. 4. Use a 3.5 mm drill bit to drill holes for the flathead screws. 5. Cut or drill a circle approximately 25 mm in size that lines up with the large hole of the Mounting Bracket. This will be used to feed the Ethernet cable through the tile. Ubiquiti Networks, Inc. UniFi™ AP-Mini User Guide Note: The UniFi AP-Mini supports Passive PoE, which works with the included PoE adapter. If you want to power the UniFi AP-Mini from an 802.3af compliant switch, Ubiquiti Networks offers the optional Instant 802.3af Adapter to instantly transform any PoE device into a fully 48V 802.3af compliant product. Product details are available on our website at http://ubnt.com/8023af Chapter 2: Installation PC Users 1. Launch UniFi-installer.exe. 2. Click Install. 8. Refer to steps 6 and 7 for alignment details (see “WallMount” on page 3). Turn the AP clockwise until it locks into place. Software Installation Insert the UniFi Controller software CD into your CD‑ROM drive and follow the instructions for your specific computer type. 3. If your computer doesn’t have Java 1.6 or above installed, you will be prompted to install it. Click Install to continue. Mac Users 1. Click the Install icon. 4. Click Next. 2. Click Continue and follow the on-screen instructions to install the software. 5. Ensure that the Start UniFi Controller after installation option is checked and click Finish. 3. Go to Go > Applications. Double-click the UniFi icon. Note: The UniFi Controller software can also be launched from Start > All Programs. Proceed to “Configuring the UniFi Controller Software” on page 6. Ubiquiti Networks, Inc. UniFi™ AP-Mini User Guide Configuring the UniFi Controller Software 1. The UniFi Controller software startup will begin. Click Launch a Browser to Manage Wireless Network. Chapter 2: Installation c. To enable guest access, select Enable Guest Access and enter a guest network name in the Guest SSID field. d. Click Next. 5. Enter an admin name in the Admin Name field and password in the Password field to use when accessing the management interface. Confirm your password in the Confirm field. Click Next. 2. Select your language and country. Alternatively, you can restore from a previous backup by clicking Browse. Click Next. 6. Review your settings. Click Back to make changes or Finish to save your settings. Once finished you will be redirected to the management interface via your Web browser. 3. Select the devices that you want to configure and click Next. Congratulations, your wireless network is now configured. 4. The UniFi Installation Wizard will create a secure primary wireless network for your devices. Perform the following steps: a. Enter the wireless network name (SSID) in the Secure SSID field. A login screen will appear for the UniFi Controller management interface. Enter the admin name and password that you created and click Login. Proceed to the next chapter for information on using the UniFi Controller software. b. Enter a passphrase to be used for your primary network in the Security Key field. Ubiquiti Networks, Inc. UniFi™ AP-Mini User Guide Chapter 3: Using the UniFi Controller Software The UniFi Controller software that comes with your UniFi AP-Mini has a browser-based interface for easy configuration and management. To access the interface, perform the following steps: 1. Launch the UniFi Controller application if hasn’t already been started. • Mac users: Go > Applications > UniFi • Windows users: Start > All Programs > Ubiquiti UniFi. 2. The UniFi login screen will appear. Enter the admin name and password in the appropriate fields and click Login. Chapter 3: Using the UniFi Controller Software Access Points • connected Drop-down clickable list of all of the Access Points that are online. • disconnected Displays a list of Access Points that were previously online but are no longer accessible. • pending Drop-down clickable list of all of the Access Points that are not yet managed but are available for management. Stations • users Displays the total number of users connected to the primary network. • guests Displays the total number of users connected to the guest network. Recent Events Displays a list of recent events including the date and time the event occurred and the details of the event. The User and Access Point names are clickable links. Interface Tabs The UniFi software consists of six primary tabs. This User Guide covers each tab with a chapter. For details on a specific tab, refer to the appropriate chapter. • “Map Tab” on page 13 • “Statistics Tab” on page 20 • “Access Points Tab” on page 22 • “Users Tab” on page 23 • “Guests Tab” on page 24 Event Slider Move the slider right and left to navigate between pages of events. • “Offline Clients Tab” on page 25 Search Allows you to enter text you want to search for. Simply begin typing; there is no need to press Enter. Common Interface Options Clicking on an Event Device Link The common interface options are accessible from all tabs in the UniFi interface. The event messages have clickable links [in brackets underlined in gray text] for AP (see “Access Point Details” on page 26), User, and Guest (see “User/Guest Details” on page 34). Details vary based on the selection. Ubiquiti Networks, Inc. UniFi™ AP-Mini User Guide Alerts Chapter 3: Using the UniFi Controller Software Settings > System Important events are displayed in the alerts window. The date and time of the event and the message are displayed. System Configuration System Name Editable field with the system name. Search Allows you to enter text you want to search for. Simply begin typing; there is no need to press Enter. Show Archived Show all of the alert messages that have been archived. Archive All Archive all of the alert messages displayed on the screen. Adopt Click to adopt an Access Point that is waiting for adoption. Archive Archive the selected alert message. Settings Country Select your country from the drop-down list. Services Automatic Upgrade When enabled, this option will automatically upgrade your firmware when an update is available. LED When enabled, this option will illuminate the LED on the Access Point. When disabled, this option will turn off the LED on the Access Point. Background Scanning When enabled, all managed Access Points will scan in the background for “Rogue Access Points” — third-party Access Points or UniFi Access Points that are being managed by another instance of the UniFi Controller software. This option is disabled by default. • Scan Now When clicked, all managed Access Points will scan for a 2-3 second period across all maps for Access Points. New Access Points in their default state will appear under Access Points > Pending. Additionally, Background Scanning will automatically detect Access Points that have been disconnected and attempt to reconnect them. System System related settings. Guest Control Guest portal and policies. Wireless Networks Wireless networks. Blocked Devices List of blocked wireless devices. >_ Admin Settings Admin username, password, and preferences. Load Balancing Sets a desired number of clients per AP. While an AP will allow more clients to connect, it will start to look at those with lower signals and disconnect them. Network Discovery When enabled, this option allows UniFi to be discoverable via UPnP. This option is disabled by default. Connectivity Monitor When enabled, all managed Access Points will use the Gateway of the Access Point that is providing IP information either by DHCP or Static designation. If you select Custom, you can specify an alternate Uplink IP address. Gateway is selected by default. Remote Logging Enable to define a remote syslog server. Enter the IP address and port of the syslog server. Click Apply to save any changes that you have made. User Groups User Group settings. Ubiquiti Networks, Inc. UniFi™ AP-Mini User Guide Mail Server When enabled, UniFi will send email alerts when triggered (Pending Access Points and Disconnected Access Points) to the administrator email address specified under Settings > Admin Settings > Admin Preferences > Email Alert. SMTP Server Enable by selecting the checkbox and entering the outgoing (SMTP) mail server name. Optionally, you may enable Secure Sockets Layer (SSL) to provide communication security over the Internet. The port number will automatically change to 465. Enable authentication Enable by selecting the checkbox and entering the username and password required by the mail server. Test SMTP Server Enter an email address and click Send to test the mail server setup. Chapter 3: Using the UniFi Controller Software • No authentication When this option is selected, guests are not required to log in, but must accept the Terms of Use. When you select No authentication, you must select Guest Policy under Settings > Wireless Networks > SSID > Edit > Wireless Configurations in order to enforce selection of the Terms of Use by the guest. • Simple Password When this option is selected, guests are required to enter the simple password and accept the Terms of Use. When you select Simple Password, you must select Guest Policy under Settings > Wireless Networks > SSID > Edit > Wireless Configurations in order to enforce entry of the password and selection of the Terms of Use by the guest. Apply Click Apply to save changes. Settings > Guest Control • Hotspot When selected, enables Hotspot functionality including the ability to customize portal login pages and bill customers using major credit cards or via PayPal™. When you select Hotspot, you must select Hotspot > Voucher and/or Hotspot > Payment as a method of Hotspot authorization. Also, you must select Guest Policy under Settings > Wireless Networks > SSID > Edit > Wireless Configurations in order to enforce entry of voucher, payment, and Terms of Use by the guest. Guest Policies Guest Portal This option is disabled by default. When disabled, guests can access the Internet without entering a password or accepting Terms of Use. When this option is enabled, you can control the Guest Portal. Authentication When the Guest Portal is enabled, the authentication options will appear. There are four different authentication methods available: • External Portal Server If using an external server to host a custom guest portal, enter the IP address in the Custom Portal > IP Address box using the following format: 192.168.0.0. • Guest Password (Option only visible when using Simple Password authentication) Enter a password that guests must enter before accepting the Terms of Use and connecting to the Internet. Ubiquiti Networks, Inc. UniFi™ AP-Mini User Guide • Expiration (Option only visible when using No authentication or Simple Password authentication) Allows the specification of guest login expiration after a designated period of time. Options include: 8 hours, 24 hours, 2 days, 3 days, 4 days, 7 days, and User-defined. User-defined can be designated in minutes, hours, and days. Chapter 3: Using the UniFi Controller Software Vouchers, and Operator Accounts. See “Hotspot Manager” on page 36. • Apply Click Apply to save changes. When logging in with No authentication, guests will be required to accept the Terms of Use before gaining access to the Internet. • Custom Portal (Option only visible when using External Portal Server authentication) Enter the IP address using the following format: 192.168.0.0. • Landing Page The landing page is the page where guests are redirected after accepting the Terms of Use. There are two options available: -- Redirect to the original URL When this option is selected, guests are directed to the URL they requested after accepting the Terms of Use. -- Promotional URL When this option is selected, guests are redirected to the URL that you specify here after accepting the Terms of Use. Specify the URL with http:// in front of the Web address. Example: http://www.ubnt.com When logging in with Simple Password authentication, guests will be required to enter the Guest Password and accept the Terms of Use before gaining access to the Internet. • Portal Customization When enabled, allows customized portal pages to appear in place of default login pages. See “Portal Customization” on page 38 for details on setting up custom portal pages. • Portal URL Hostname Allows the designation of a hostname for the portal URL in place of the default IP address. Paired with a SSL certificate, ensures site certificates are displayed as trusted in the guest browser. Example: www.ubnt.com Hotspot The Hotspot options are only visible when Hotspot authentication is selected. When logging in with Voucher-based Hotspot authentication, guests will be required to enter the voucher number and accept the Terms of Use before gaining access to the Internet. • Voucher When selected, vouchers (including distributable code, duration values, and use restrictions) can be created using Hotspot Manager (see “Hotspot Manager” on page 36). • Payment When enabled, allows payment-based authentication to be set up with your PayPal Website Payments Pro account. Payments and Transactions can be managed using Hotspot Manager (see “Hotspot Manager” on page 36). • PayPal PayPal account details are entered here: -- Username Enter the corresponding Username. -- Password Enter the corresponding Password. -- Signature Enter the corresponding Signature for the PayPal account to be used for receiving payments. When logging in with Payment-based Hotspot authentication, guests will be required to select the package type, click the payment choice, and accept the Terms of Use before gaining access to the Internet. -- Use Paypal Sandbox For PayPal testing purposes, enable this option and click Apply Sandbox Account to set up/access your PayPal Sandbox Test Environment. • Hotspot Operator Click Go to Hotspot Manager to manage Wireless Guests, Payments/Transactions, Ubiquiti Networks, Inc. 10 UniFi™ AP-Mini User Guide Access Control Chapter 3: Using the UniFi Controller Software Wireless Configuration Restricted Subnets Enter any subnets that you don’t want guests to be able to access. Apply Click Apply to save changes. Settings > Admin Settings Admin Name Displays the current admin name used to log in. To change the admin name, simply enter a new name and click Apply. • Name/SSID Allows you to edit the wireless network name (SSID). • Security Selects the type of security to use on your wireless network. Password A new password can be entered in this field. Ensure that you enter the password again in the Confirm field and then click Apply to save your new password. -- Open This option is typically only used on the Guest network. When enabled, wireless network access is open to anyone without needing a password. Confirm Used to confirm your new password. -- WEP WEP (Wired Equivalent Privacy) is the oldest and least secure security algorithm. WPA security methods should be used when possible. Language Selects the language for use in the interface. Email Alert Select to enable email alerts and enter the administrator email address in the Send alert to email box. See “Mail Server” on page 9 for information on setting up the outgoing (SMTP) mail server. • WEP Key Enter a WEP encryption key in hexadecimal format. You can enter a 64-bit or 128‑bit key: Apply Click Apply to save changes. Type HEX Settings > Wireless Networks 64-bit 10 Hexadecimal Characters (0-9, A-F, or a-f ) Example: 00112233AA 128-bit 26 Hexadecimal Characters (0-9, A-F, or a-f ) Example: 00112233445566778899AABBCC • Key Index Specifies the Index of the WEP Key used. Four different WEP keys can be configured at the same time, but only one is used. The effective key is set by choosing 1, 2, 3, or 4. -- WPA-Personal WPA™ or Wi-Fi Protected Access was developed as an encryption method stronger than WEP. WPA-Personal requires a passphrase to connect to the wireless network. Wireless Configurations Name Displays the wireless network name (SSID). Security Displays the type of security being used on your wireless network. Guest Network Indicates whether the network is a guest network. Actions Select an action button to perform the desired action: • Edit Select to make changes to the wireless network settings. • Delete Select to delete the wireless network. Ubiquiti Networks, Inc. • Security Key Enter the passphrase that users will use to connect to the wireless network. -- WPA-Enterprise WPA Enterprise uses a RADIUS server to authenticate users on the wireless network. • IP Address This is where the IP address of the RADIUS server is specified. • Port The port number is entered here. By default it is 1812. • Password The password used to authenticate on the RADIUS server is entered here. • Guest Policy Select this option to enable guest access policies on this wireless network. 11 UniFi™ AP-Mini User Guide Chapter 3: Using the UniFi Controller Software Advanced • VLAN To use a VLAN, select Use VLAN ID and enter the port number. • Hide SSID Select this option if you don’t want the SSID to be broadcast. • WPA Defines supported WPA and encryption methods. • User Group Allows assignment of wireless users to a specific user group. Click Apply to save any changes that you have made. Click Cancel to discard changes. Edit Click to change the name or bandwidth settings of the user group. Settings > Blocked Devices Delete Click to delete the user group. Displays the list of blocked wireless devices. See “Configuration” on page 35 for information on the application of User Groups to Users/Guests. Admin Unblock Click to unblock a wireless device. See “User/ Guest Details” on page 34 for information on blocking wireless devices. Settings > User Groups The Admin tab displays server version information, allows system backups to be created and downloaded, allows system restoration from backup files, and allows configuration information to be downloaded to assist in support issues. Server Information Version The software version is displayed here. If there is an update, UniFi will automatically download it and display it here. Backup Create Click to create a new user group. Download Backup Settings Click to download a file that contains all of your settings so you can restore them later if you choose. Restore Choose File Select this option to restore settings from a backup file that you’ve already downloaded. Support Info • Name Enter a descriptive user group name. • Bandwidth Limit (Download) When selected, allows the designation of a download bandwidth limit in Kbps. Download Support Info Select this option to download a file to your computer with information about your configuration that can be emailed to our support team. • Bandwidth Limit (Upload) When selected, allows the designation of an upload bandwidth limit in Kbps. -- Create Click to create a user group. -- Cancel Click to cancel user group creation. Ubiquiti Networks, Inc. 12 UniFi™ AP-Mini User Guide Chapter 4: Map Tab The UniFi Controller software allows you to upload custom map images of your location(s) or use Google Maps™ for a visual representation of your wireless network. When you initially launch the UniFi Controller application, a default map is displayed. Chapter 4: Map Tab Once you’ve created the map, you can upload it to the UniFi Controller software by performing the following steps: 1. Click Configure Maps. Configure Maps button Adding Custom Maps To add a custom map, you must first create the image using an illustration, image editing, or blueprint application that exports .jpg, .gif, or .png file formats. Ubiquiti Networks, Inc. 13 UniFi™ AP-Mini User Guide 2. Click Add a Map. Chapter 4: Map Tab 4. Click Close. Add a Map 3. Enter a map name in the Description field and click Upload my own. Click the Browse button to locate the file to use as a map (valid file formats are .jpg, .gif, and .png). Click Continue. Adding a Google Map To add a Google Map to the UniFi Controller software Map view: 1. Click Configure Maps. Configure Maps button Ubiquiti Networks, Inc. 14 UniFi™ AP-Mini User Guide 2. Click Add a Map. Add a Map Chapter 4: Map Tab 5. Click or copy and paste the Web link from the window into a new Web browser window. Do not close the UniFi window. http://code.google.com/apis/maps/signup.html 3. Enter a map name in the Description field and click Use Google Maps. Click Continue. 6. You need to be signed in with a Google account to obtain a Google Maps API key. 7. Review the terms and conditions and click the checkbox next to I have read and agree with the terms and conditions. 8. Navigate back to the UniFi window and copy the address that UniFi displays in the address bar. Note: You only need to copy until the end of the address; do not include the port information. In the example below, the full address is https://192.168.25.191:8443/ manage#. You only need to copy up to https://192.168.25.191. Do not include the colon or anything beyond it. 9. Navigate back to the Google Maps API Family window and paste the address into the My web site URL: box. 10. Click the Generate API Key button. 4. In order to use a Google Map, you must register with Google for a Google Maps API key. To do so, click Specify API Key. Ubiquiti Networks, Inc. 15 UniFi™ AP-Mini User Guide 11. A new window will open, displaying your key. Highlight and copy the Google Maps API key. Google Maps API Key Chapter 4: Map Tab 14. Select Specify Address to enter an address. Type in the address and then click Go. You also have the Specify Coordinates option to enter the latitude and longitude of a specific location. 15. The specified location should appear. Click Save. 12. Navigate back to the UniFi window and paste the API Key into the API Key field. Click continue. 13. The default Google Map location will appear. Click the Set Location button in the lower left. 16. Click Close. Set Location button 17. You can adjust the zoom using the slider on the right. Ubiquiti Networks, Inc. 16 UniFi™ AP-Mini User Guide Placing Access Points on the Map 1. Drag the Access Point icon(s) from the Unplaced APs list on the left to the appropriate location(s) on the map. Chapter 4: Map Tab Details Brings up the Details window. This allows you to view Access Point settings and connected users. You can also edit the radio channel, transmit power, uplink, and device alias. In the Details window, there are four tabs: Details, Users, Guests, and Configuration. The access point will appear in the area that you placed it. • Details Displays details on the Access Point including the MAC address, model, version, IP address, uptime, connected users, and connected guests. Click Uplink (Wire) to display the speed, duplex, Down Pkts / Bytes, Up Pkts / Bytes, and Activity. Click Radio to display the channel used, transmit power, and packet information. • Users Displays the hostnames of the users that are connected to the selected Access Point and the IP addresses assigned to them. Wired/Wireless Access Point Shows the location of the Access Point on the map. Click and hold this icon to drag the Access Point to another location on the map. Click the Access Point icon to reveal additional options. Click a blank area of the map to hide them. Lock Locks the selected Access Point in the current location on the map. You can click the hostname to display additional details of each user. A window with Details, Statistics, and Configuration is displayed. The Details tab displays the MAC address, hostname, IP address, uptime, and the name of the connected Access Point. The Statistics tab displays the channel used, signal strength, transmit and receive rates, power saving enabled or disabled, and the number of packets sent and received. You can also click History to see a sortable list of events. The Configuration tab allows you to change the alias name for the device. • Guests Displays the MAC address of guests that are connected to the guest network. • Configuration Allows you to change the alias name of the device and channel setting. You can also set the transmit power to Auto, High, Medium, Low, or Custom. You can also remove the Access Point if you no longer want to manage it with the UniFi Controller software. Remove Remove the Access Point from the location on the map. Ubiquiti Networks, Inc. 17 UniFi™ AP-Mini User Guide Show: You can click each of the following options to display Access Point labels, details, wireless coverage, and topology on the map. Chapter 4: Map Tab • Coverage Displays a visual representation of the wireless range covered by the Access Point. • Labels Displays the name applied to the Access Point. Refer to Alias under “Configuration” on page 28 to change a name applied to an Access Point. If no custom label is applied, the Access Point’s MAC address will be displayed. Topology Displays a visual representation of the network configuration and connections between Access Points. Any devices that is wirelessly connected will have a wireless icon next to it. A path of arrows will indicate which device the wireless device is downlinking from. • Details Displays the Access Point name, MAC address, transmit/receive channel, number of users connected, and number of guests connected. Map: If multiple maps have been uploaded, you can select which map you want to view using this option. Ubiquiti Networks, Inc. 18 UniFi™ AP-Mini User Guide Configure Maps Use this option to add maps or edit the current map(s). Zoom Slider Use to zoom the map detail in and out. Chapter 4: Map Tab 3. Enter the distance that the line represents in the Distance: field. The distance is specified in meters by default but you can switch to feet using the drop-down selection menu on the right. Click Next. Set Map Scale Use this option to define the scale of the map. You will draw a line and define the distance that the line represents. Setting the Map Scale 1. Click the Set Map Scale button. 2. Click and hold to draw a line in the area that you want to use to set the scale of the map. If you need to redraw the line, just click and hold again to draw a new line. Once you’re happy with the line, click Next. Ubiquiti Networks, Inc. 19 UniFi™ AP-Mini User Guide Chapter 5: Statistics Tab Chapter 5: Statistics Tab Quick Look The Statistics tab provides a visual representation of the network traffic connected to your managed APs. Charts representing the number of clients and network traffic are displayed. An hour by hour chart of the usage over the last 24 hours is also displayed on this screen. Most Active AP Displays the most active Access Point’s details, including the name or MAC address of the Access Point, the total amount of data sent, and the total amount of data received. The name or MAC address of the Access Point is a clickable link that will open the device details page. See “Access Point Details” on page 26 for additional information. Clients Most Active Client Displays the details of the most active, currently connected client. The name or MAC address of the client device, the total amount of data sent, and the total amount of data received are displayed here. The name or MAC address of the client device is a clickable link that will open the device details page. See “User/ Guest Details” on page 34 for additional information. All-Time Top Client Displays the details of the all-time most active client. The name or MAC address of the client device, the total amount of data sent, and the total amount of data received are displayed here. # of Clients Displays a visual pie chart representation of the client distribution. Place the mouse cursor over the chart for percentage details. Ubiquiti Networks, Inc. The name or MAC address of the client device is a clickable link that will open the device details page. See “User/ Guest Details” on page 34 for additional information. 20 UniFi™ AP-Mini User Guide Chapter 5: Statistics Tab Current Usage - Top Access Points # of Clients Displays a visual pie chart representation of the client distribution on the most active Access Points. Place the mouse cursor over the chart for percentage details. Traffic Displays a visual pie chart representation of traffic on the most active Access Points. Place the mouse cursor over the chart for percentage details. Recent Activities The Recent Activities statistics can be toggled between a view for the last 24 hours and a view for the last 30 days. # of Clients Displays a visual graph of the number of clients connected during the selected time period (last 24 hours or last 30 days). Traffic Displays a visual graph of the network traffic during the selected time period (last 24 hours or last 30 days). Ubiquiti Networks, Inc. 21
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.7 Linearized : Yes Author : J Lee Create Date : 2011:11:28 10:03:09-08:00 Modify Date : 2011:11:28 10:04:01-08:00 Tagged PDF : Yes XMP Toolkit : Adobe XMP Core 4.2.1-c043 52.372728, 2009/01/18-15:08:04 Metadata Date : 2011:11:28 10:04:01-08:00 Creator Tool : Adobe InDesign CS5.5 (7.5.2) Format : application/pdf Title : UniFi AP-Mini User Guide Creator : J Lee Document ID : uuid:8fb60c42-48e9-40f4-bfcc-2ebee83f8824 Instance ID : uuid:8251423f-ec13-4de3-93f9-92691c7721e0 Producer : Adobe PDF Library 9.9 Page Count : 24EXIF Metadata provided by EXIF.tools