Ubiquiti UAPXG UniFi Access Point User Manual UniFi AP XG Quick Start Guide
Ubiquiti Networks, Inc. UniFi Access Point UniFi AP XG Quick Start Guide
Ubiquiti >
Contents
User Manual
| Download: |  |
| Mirror Download [FCC.gov] | |
| Document ID | 3615796 |
| Application ID | JCb3sATiu5s+IqMpz/RFWA== |
| Document Description | User Manual |
| Short Term Confidential | No |
| Permanent Confidential | No |
| Supercede | No |
| Document Type | User Manual |
| Display Format | Adobe Acrobat PDF - pdf |
| Filesize | 408kB (5099956 bits) |
| Date Submitted | 2017-10-24 00:00:00 |
| Date Available | 2018-04-23 00:00:00 |
| Creation Date | 2017-09-14 18:38:18 |
| Producing Software | Adobe PDF Library 15.0 |
| Document Lastmod | 2017-10-23 18:38:54 |
| Document Title | UniFi AP XG Quick Start Guide |
| Document Creator | Adobe InDesign CC 2017 (Macintosh) |
| Document Author: | A Imaoka |
Quad-Radio 802.11ac Wave 2 Access Point with Dedicated Security Model: UAP-XG Introduction Thank you for purchasing the Ubiquiti Networks® UniFi® Quad‑Radio 802.11ac Wave 2 Access Point with Dedicated Security. This Quick Start Guide is designed to guide you through installation and includes warranty terms. IMPORTANT: The UAP-XG requires the UniFi Controller v5.7 or higher, available at: www.ubnt.com/download/unifi Package Contents UniFi AP XG Mounting Plate T-Bar Mounts T-Bar Screws (Qty. 2) (Qty. 2) Ceiling Backing Ceiling Screws Keps Nuts Plate (Qty. 4) (Qty. 4) Allen Wrench Wall Screws Screw Anchors (Qty. 4) (Qty. 4) Quad-Radio 802.11ac Wave 2 Access Point with Dedicated Security Model: UAP-XG Release Tool Cable Feed Plug Gigabit PoE (50V, 1.2A)* Power Cord* Quick Start Guide *Gigabit PoE and Power Cord are not included with UAP-XG 5-pack TERMS OF USE: Ubiquiti radio devices must be professionally installed. Shielded Ethernet cable and earth grounding must be used as conditions of product warranty. It is the professional installer’s responsibility to follow local country regulations, including operation within legal frequency channels, output power, and Dynamic Frequency Selection (DFS) requirements. Installation Requirements • Phillips screwdriver • Drill and drill bit (8 mm for wall mounting or 3 mm for ceiling tile mounting) • Optional: Drywall or keyhole saw (to cut 18 mm hole for Ethernet cable feed) • Cat6A UTP cable for indoor installations Outdoor Installation Requirements IMPORTANT: The UAP-XG may be installed outdoors under an eave or other protected location. Do not install the UniFi AP in an open environment. • Mounting location should be at least 60 cm (2 ft) from the edge of the eave or ceiling. • Cable feed opening must be directed away from the open environment. • Cable feed must be pointed downwards when wall-mounted. • Shielded Category 6 (or above) cabling should be used for all outdoor wired Ethernet connections and should be grounded through the AC ground of the PoE. System Requirements • Linux, Mac OS X, or Microsoft Windows 7/8/10 • Java Runtime Environment 1.6 (1.8 or newer recommended) • Web Browser: Google Chrome (Other browsers may have limited functionality.) • UniFi Controller software v5.7 or newer (available at: www.ubnt.com/download/unifi) Network Topology Requirements • A DHCP-enabled network (for the AP to obtain an IP address as well as for the wireless clients after deployment) • A UniFi Cloud Key or management station running the UniFi Controller v5.7 (or newer) software, located either on-site and connected to the same Layer 2 network, or off-site in the cloud or NOC UAP-AC-PRO UAP-XG UAP-AC-M-PRO CURRENT SITE USERNAME Default 25 0.9 msec LATENCY 59 22 54 116 WAN 118 0.2 0.94 0.01 200+ 229 LAN 413 admin WLAN ACTIVE DEVICE Inactive Pending 2.33 700+ Mbps THROUGHPUT 118 ACTIVE DEVICES Inactive Pending ACTIVE DEVICES Inactive Pending SPEED TEST DOWNLOAD THROUGHPUT & LATENCY DEVICES ON 2.4 GHZ CHANNEL Throughput [Mbps] 250 10 200 150 100 50 Latency [msec] 24 HRS 12 HRS NOW Avg/Max Throughput 36 100 40 44 48 52 10 56 60 120 124 11 64 10 60 40 20 24 HRS 12 HRS DEVICES NOW Latency [msec] 80 DEVICES ON 5 GHZ CHANNEL Latency UPLOAD THROUGHPUT & LATENCY Throughput [Mbps] UniFi Switch WLAN LAN WAN 118 100 132 CLIENTS 126 DEVICES 104 136 108 140 112 144 116 149 153 157 128 161 165 DEEP PACKET INSPECTION 1172 CLIENTS Motorola Lenovo SamsungE Dell Acer Other 258 241 220 213 130 110 645 GB TRAFFIC Network Protocols Streaming Media Web / Web 2.0 File Transfer Social Network Other 582 GB 23.3 GB 22.7 GB 8.47 GB 3.6 GB 5.46 GB UniFi Hybrid Cloud Install US-16-XG LAN USG-PRO-4 (DHCP Server) WAN Internet CURRENT SITE USERNAME Default 25 0.9 msec LATENCY 59 22 54 116 WAN 118 0.2 0.94 0.01 200+ 229 LAN 413 admin WLAN ACTIVE DEVICE Inactive Pending 2.33 700+ Mbps THROUGHPUT 118 ACTIVE DEVICES Inactive Pending ACTIVE DEVICES Inactive Pending SPEED TEST DOWNLOAD THROUGHPUT & LATENCY DEVICES ON 2.4 GHZ CHANNEL 10 200 150 100 50 Latency [msec] Throughput [Mbps] 250 24 HRS 12 HRS NOW Avg/Max Throughput Throughput [Mbps] 10 80 60 40 20 24 HRS 12 HRS DEVICES NOW Latency [msec] 100 WLAN LAN WAN 10 11 118 36 40 44 48 52 56 60 64 100 104 108 112 116 120 124 128 132 CLIENTS 126 DEVICES DEVICES ON 5 GHZ CHANNEL Latency UPLOAD THROUGHPUT & LATENCY 136 140 144 149 153 157 161 165 DEEP PACKET INSPECTION 1172 CLIENTS Motorola Lenovo SamsungE Dell Acer Other 258 241 220 213 130 110 645 GB TRAFFIC Network Protocols Streaming Media Web / Web 2.0 File Transfer Social Network Other 582 GB 23.3 GB 22.7 GB 8.47 GB 3.6 GB 5.46 GB Remote Access to UniFi Controller Sample Network Diagram All UniFi devices support off-site management controllers. For setup details, see the User Guide on the website: www.ubnt.com/download/unifi Hardware Overview LED LED Color Status White Factory default, waiting to be integrated. Flashing White Initializing. Alternating White/Blue Device is busy; do not touch or unplug it. This usually indicates that a process such as a firmware upgrade is taking place. Blue Indicates the device has been successfully integrated into a network and is working properly. This is used to locate an AP. Quickly Flashing Blue When you click Locate in the UniFi Controller software, the AP will flash. It will also display the location of the AP on the map. Steady Blue Indicates the device is in an isolated state with Occasional (all WLANs are brought down until an Flashing uplink is found). Ports Security Slot M/N: UAP-XG 802.3bt PoE FCC ID: SWX-UAPXG Contains FCC ID: SWX-M442G Contains FCC ID: SWX-M445GL Contains FCC ID: SWX-M445GH Reset Button IC: 6545A-UAPXG Contains IC: 6545A-M442G Contains IC: 6545A-M445GL Contains IC: 6545A-M445GH 1 GbE Port 10 GbE Port Reset The Reset button serves two functions for the UniFi AP: • Restart Press and release the Reset button quickly. • Restore to Factory Default Settings Press and hold the Reset button for more than five seconds. 1 GbE The 1 GbE port is a 10/100/1000 Ethernet port used for bridging. It can also be used to connect the power. 10 GbE The 10 GbE port is a 1/10 Gbps Ethernet port used to connect the power and should be connected to the LAN and DHCP server. For 10 Gbps operation, connect the UAP-XG to an 802.3bt POE switch. Note: The UAP-XG can also be powered using the included Gigabit PoE adapter. For instructions on using the adapter, see Powering the UniFi AP. Note: If you need to remove the UniFi AP from the Mounting Plate, insert the included Release Tool in the Security Slot to release the Lock Tab and turn the UniFi AP counterclockwise. Mounting Plate The Mounting Plate offers a variety of mounting holes for different applications. The legend printed on the Mounting Plate identifies the holes used for each application. Upgrade from UAP-AC-PRO The UAP-XG is compatible with the UAP‑AC‑PRO mounting hardware, so you only need to remove the UAP‑AC‑PRO and replace it with the UAP-XG. To begin the upgrade: 1. Insert the Release Tool into the UAP-AC‑PRO Security Slot to disengage the lock. Then turn the UAP‑AC‑PRO counterclockwise and lift it off of the mounting bracket. Security Slot UAP-AC-PRO (Wall Mount Installation) 2. Unplug the Ethernet cable from the Main port. 3. Go to the Connecting Ethernet section. Hardware Installation The UniFi AP can be mounted on a wall, ceiling tile, drop ceiling T-rail (up to 40 mm), or electrical junction box. Perform the steps for the appropriate installation. Note for UniFi AP replacement: The holes marked “A” on the Mounting Plate line up with the holes of mounting brackets used for previous UniFi AP models. Wall Mount 1. Position the Mounting Plate at the desired location on the wall with the Arrow pointing up. 2. Mark the four mounting holes marked “A”, and use an 8 mm drill bit to drill the holes. If your Ethernet cable feeds through the wall, cut or drill a hole approximately 18 mm in diameter. Then feed the CAT6A cable through the hole. Arrow Optional 18 mm Hole for Ethernet Cable Feed through the Wall *640-00341-01* 640-00341-01 3. Insert the Screw Anchors into the holes. Secure the Mounting Plate to the wall by inserting the Wall Screws into the anchors. 4. Go to the Connecting Ethernet section, and then return to step 5. 5. Align the Arrow on the top edge of the UniFi AP with the Arrow on the Mounting Plate. Arrow Arrow Lock Tab 6. Rotate the UniFi AP clockwise until the tabs lock into place and the Lock Tab engages. Ceiling Mount 1. Remove the ceiling tile. 2. Place the Ceiling Backing Plate in the center of the ceiling tile. Mark the four mounting screw holes and an 18 mm hole for the Ethernet cable feed. Optional 18 mm Hole for Ethernet Cable Feed through the Ceiling Tile 3. Use a 3 mm drill bit to drill the screw holes, and cut or drill the 18 mm hole for the Ethernet cable feed. 4. Insert the Ceiling Screws through the Mounting Plate, ceiling tile, and Ceiling Backing Plate. Fasten the screws using the Keps Nuts. Then feed the Ethernet cable through the tile and bracket. 5. Perform the steps in the Connecting Ethernet section, and then return to step 6. 6. Align the Arrow on the top edge of the UniFi AP with the Arrow on the Mounting Plate. Arrow Lock Tab Arrow 7. Rotate the UniFi AP clockwise until the tabs lock into place and the Lock Tab engages. 8. Set the ceiling tile back into place. T-Bar Mount 1. Remove the ceiling tiles on both sides of the T-bar you will use for mounting. 2. Loosen the set screws of the T-Bar Mounts. 3. Insert the T-bar into a T-Bar Mount, and turn the T-Bar Mount clockwise to attach it. Use the included Allen Wrench to tighten the two set screws to secure the T-Bar Mount. 4. Attach the second T-Bar Mount but do not tighten the set screws. 5. Use the two dashed lines on the Mounting Plate to space the T-Bar Mounts 77 mm (3") apart. 77 m 6. Tighten the two set screws on the second T-Bar Mount. 7. Insert the included T-Bar Screws into the holes marked “B” on the Mounting Plate, and then secure the plate to the T-Bar Mounts. 8. Drop the Ethernet cable between the plate and T-bar. 9. Perform the steps in the Connecting Ethernet section, and then return to step 10. 10. Align the Arrow on the top edge of the UniFi AP with the Arrow on the Mounting Plate. Arrow Lock Tab Arrow 11. Rotate the UniFi AP clockwise until the tabs lock into place and the Lock Tab engages. 12. Set the ceiling tiles back into place. Junction or Outlet Box Mount 1. Use the legend printed on the Mounting Plate to select the appropriate mounting holes for your installation. 2. Pull the Ethernet cable through the Mounting Plate, and attach the Mounting Plate to the junction or outlet box using at least two screws (not included). Note: For in-wall applications, position the Mounting Plate with the Arrow pointing upwards. 3. Perform the steps in the Connecting Ethernet section, and then return to step 4. 4. Align the Arrow on the top edge of the UniFi AP with the Arrow on the Mounting Plate. Arrow Arrow Lock Tab 5. Rotate the UniFi AP clockwise until the tabs lock into place and the Lock Tab engages. Connecting Ethernet 1. Remove the rubber port cover from the UniFi AP. 2. If the Ethernet cable runs along the mounting surface, skip to step 3. If the Ethernet cable is fed through the wall or ceiling, insert the Cable Feed Plug. 3. Feed the Ethernet cable through the port cover. Note: The feed hole will stretch to accommodate the RJ45 connector, and then seal around the cable. 4. Connect the Ethernet cable to the 10 GbE port and replace the port cover. Return to the appropriate instructions. M/N: UAP-XG 802.3bt PoE FCC ID: SWX-UAPXG Contains FCC ID: SWX-M442G Contains FCC ID: SWX-M445GL Contains FCC ID: SWX-M445GH IC: 6545A-UAPXG Contains IC: 6545A-M442G Contains IC: 6545A-M445GL Contains IC: 6545A-M445GH Powering the UniFi AP The UAP-XG features auto-sensing 802.3bt PoE support and can be powered by any 802.3bt PoE compliant switch. To power the UniFi AP, connect the Ethernet cable from the UniFi AP directly to a PoE+ port on the switch. 802.3bt PoE Switch Note: If you do not have an 802.3bt PoE compliant switch, use the included Gigabit PoE adapter to power the UniFi AP as follows: 1. Connect the Ethernet cable from the 10 GbE port of the UAP-XG to a 10 GbE (or 1 GbE) switch port. 2. Connect an Ethernet cable from the 1 GbE port of the UAP-XG to the adapter’s PoE port. 3. Connect the Power Cord to the adapter’s power port. Connect the other end of the Power Cord to a power outlet. Software Installation Download and install the latest version of the UniFi Controller software. Launch it and follow the on-screen instructions. The software and step-by-step instructions in the User Guide are available at: www.ubnt.com/download/unifi After you have installed the software and run the UniFi Installation Wizard, a login screen will appear for the UniFi Controller management interface. Enter the Admin Name and Password that you created and click Log In. You can manage your wireless network and view network statistics using the UniFi Controller management interface. For information on configuring and using the UniFi Controller software, refer to the User Guide. Mobile App Installation Ubiquiti Networks also offers the UniFi mobile app, which is available from the App Store (iOS) or Google Play™ Store (Android). You can use it to provision a UniFi AP for basic functionality without configuring a UniFi Controller. It also allows seamless provisioning of APs for remote controllers (controllers not on the same Layer 2 network) and easy access to local controllers and those monitored on unifi.ubnt.com Specifications UAP‑XG Dimensions Weight without Mount Networking Interface Buttons Power Method 228 x 228 x 50 mm (8.98 x 8.98 x 1.97") 1300 g (2.87 lb) (1) 10/100/1000 RJ45 Ethernet Port (1) 1/10 Gbps ICM Ethernet Port Reset PoE+ 802.3bt Max. Power Consumption 31W Supported Voltage Range 44‑57VDC Max. TX Power 2.4 GHz 5 GHz 25 dBm 25 dBm MIMO 2.4 GHz 5 GHz 4x4 4x4 Throughput Speeds 2.4 GHz 5 GHz Antennas Antenna Gain 2.4 GHz 5 GHz Wi-Fi Standards Wireless Security Mounting 800 Mbps 1.7 Gbps Integrated Internal Antenna 6 dBi 8 dBi 802.11 a/b/g/n/ac/ac-wave2 WEP, WPA-PSK, WPA-Enterprise (WPA/WPA2, TKIP/AES) Wall/Ceiling/Junction Box (Kits Included) Operating Temperature -10 to 60° C (14 to 140° F) Operating Humidity 5 to 95% Noncondensing Certifications CE, FCC, IC Safety Notices 1. Read, follow, and keep these instructions. 2. Heed all warnings. 3. Only use attachments/accessories specified by the manufacturer. WARNING: Do not use this product in a location that can be submerged by water. WARNING: Avoid using this product during an electrical storm. There may be a remote risk of electric shock from lightning. Electrical Safety Information 1. Compliance is required with respect to voltage, frequency, and current requirements indicated on the manufacturer’s label. Connection to a different power source than those specified may result in improper operation, damage to the equipment or pose a fire hazard if the limitations are not followed. 2. There are no operator serviceable parts inside this equipment. Service should be provided only by a qualified service technician. Limited Warranty UBIQUITI NETWORKS, Inc (“UBIQUITI NETWORKS”) warrants that the product(s) furnished hereunder (the “Product(s)”) shall be free from defects in material and workmanship for a period of one (1) year from the date of shipment by UBIQUITI NETWORKS under normal use and operation. UBIQUITI NETWORKS’ sole and exclusive obligation and liability under the foregoing warranty shall be for UBIQUITI NETWORKS, at its discretion, to repair or replace any Product that fails to conform to the above warranty during the above warranty period. The expense of removal and reinstallation of any Product is not included in this warranty. The warranty period of any repaired or replaced Product shall not extend beyond its original term. Warranty Conditions The above warranty does not apply if the Product: (I) has been modified and/or altered, or an addition made thereto, except by Ubiquiti Networks, or Ubiquiti Networks’ authorized representatives, or as approved by Ubiquiti Networks in writing; (II) has been painted, rebranded or physically modified in any way; (III) has been damaged due to errors or defects in cabling; (IV) has been subjected to misuse, abuse, negligence, abnormal physical, electromagnetic or electrical stress, including lightning strikes, or accident; (V) has been damaged or impaired as a result of using third party firmware; (VI) has no original Ubiquiti MAC label, or is missing any other original Ubiquiti label(s); or (VII) has not been received by Ubiquiti within 30 days of issuance of the RMA. In addition, the above warranty shall apply only if: the product has been properly installed and used at all times in accordance, and in all material respects, with the applicable Product documentation; all Ethernet cabling runs use CAT6A (or above), and for outdoor installations, shielded Ethernet cabling is used, and for indoor installations, indoor cabling requirements are followed. Returns No Products will be accepted for replacement or repair without obtaining a Return Materials Authorization (RMA) number from UBIQUITI NETWORKS during the warranty period, and the Products being received at UBIQUITI NETWORKS’ facility freight prepaid in accordance with the RMA process of UBIQUITI NETWORKS. Products returned without an RMA number will not be processed and will be returned freight collect or subject to disposal. Information on the RMA process and obtaining an RMA number can be found at: www.ubnt.com/support/warranty Disclaimer EXCEPT FOR ANY EXPRESS WARRANTIES PROVIDED HEREIN, UBIQUITI NETWORKS, ITS AFFILIATES, AND ITS AND THEIR THIRD PARTY DATA, SERVICE, SOFTWARE AND HARDWARE PROVIDERS HEREBY DISCLAIM AND MAKE NO OTHER REPRESENTATION OR WARRANTY OF ANY KIND, EXPRESS, IMPLIED OR STATUTORY, INCLUDING, BUT NOT LIMITED TO, REPRESENTATIONS, GUARANTEES, OR WARRANTIES OF MERCHANTABILITY, ACCURACY, QUALITY OF SERVICE OR RESULTS, AVAILABILITY, SATISFACTORY QUALITY, LACK OF VIRUSES, QUIET ENJOYMENT, FITNESS FOR A PARTICULAR PURPOSE AND NON-INFRINGEMENT AND ANY WARRANTIES ARISING FROM ANY COURSE OF DEALING, USAGE OR TRADE PRACTICE IN CONNECTION WITH SUCH PRODUCTS AND SERVICES. BUYER ACKNOWLEDGES THAT NEITHER UBIQUITI NETWORKS NOR ITS THIRD PARTY PROVIDERS CONTROL BUYER’S EQUIPMENT OR THE TRANSFER OF DATA OVER COMMUNICATIONS FACILITIES, INCLUDING THE INTERNET, AND THAT THE PRODUCTS AND SERVICES MAY BE SUBJECT TO LIMITATIONS, INTERRUPTIONS, DELAYS, CANCELLATIONS AND OTHER PROBLEMS INHERENT IN THE USE OF COMMUNICATIONS FACILITIES. UBIQUITI NETWORKS, ITS AFFILIATES AND ITS AND THEIR THIRD PARTY PROVIDERS ARE NOT RESPONSIBLE FOR ANY INTERRUPTIONS, DELAYS, CANCELLATIONS, DELIVERY FAILURES, DATA LOSS, CONTENT CORRUPTION, PACKET LOSS, OR OTHER DAMAGE RESULTING FROM ANY OF THE FOREGOING. In addition, UBIQUITI NETWORKS does not warrant that the operation of the Products will be error-free or that operation will be uninterrupted. In no event shall UBIQUITI NETWORKS be responsible for damages or claims of any nature or description relating to system performance, including coverage, buyer’s selection of products (including the Products) for buyer’s application and/or failure of products (including the Products) to meet government or regulatory requirements. Limitation of Liability EXCEPT TO THE EXTENT PROHIBITED BY LOCAL LAW, IN NO EVENT WILL UBIQUITI OR ITS SUBSIDIARIES, AFFILIATES OR SUPPLIERS BE LIABLE FOR DIRECT, SPECIAL, INCIDENTAL, CONSEQUENTIAL OR OTHER DAMAGES (INCLUDING LOST PROFIT, LOST DATA, OR DOWNTIME COSTS), ARISING OUT OF THE USE, INABILITY TO USE, OR THE RESULTS OF USE OF THE PRODUCT, WHETHER BASED IN WARRANTY, CONTRACT, TORT OR OTHER LEGAL THEORY, AND WHETHER OR NOT ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. Note Some countries, states and provinces do not allow exclusions of implied warranties or conditions, so the above exclusion may not apply to you. You may have other rights that vary from country to country, state to state, or province to province. Some countries, states and provinces do not allow the exclusion or limitation of liability for incidental or consequential damages, so the above limitation may not apply to you. EXCEPT TO THE EXTENT ALLOWED BY LOCAL LAW, THESE WARRANTY TERMS DO NOT EXCLUDE, RESTRICT OR MODIFY, AND ARE IN ADDITION TO, THE MANDATORY STATUTORY RIGHTS APPLICABLE TO THE LICENSE OF ANY SOFTWARE (EMBEDDED IN THE PRODUCT) TO YOU. The United Nations Convention on Contracts for the International Sale of Goods shall not apply to any transactions regarding the sale of the Products. Compliance FCC Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions. 1. This device may not cause harmful interference, and 2. This device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operations of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense. This radio transmitters (FCC ID: SWX-UAPXG, FCC ID: SWX‑M442G, FCC ID: SWX-M445GL and FCC ID: SWX-M445GH) have been approved by FCC. ISED Canada CAN ICES-3(A)/NMB-3(A) This device complies with ISED Canada licence‑exempt RSS standard(s). Operation is subject to the following two conditions: 1. This device may not cause interference, and 2. This device must accept any interference, including interference that may cause undesired operation of the device. The radio transmitters (IC: 6545A‑UAPXG, IC: 6545A‑M442G, IC: 6545A-M445GL and IC: 6545A-M445GH) have been approved by ISED Canada. CAN ICES-3(A)/NMB-3(A) Le présent appareil est conforme aux CNR d’ISDE Canada applicables aux appareils radio exempts de licence. L’exploitation est autorisée aux deux conditions suivantes : 1. l’appareil ne doit pas produire de brouillage; 2. l’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d’en compromettre le fonctionnement. Les présents émetteurs radio (IC : 6545A‑UAPXG, IC : 6545A‑M442G, IC : 6545A-M445GL et IC : 6545A-M445GH) ont été approuvé par ISDE Canada. RF Exposure Warning The antennas used for this transmitter must be installed to provide a separation distance of at least 28 cm from all persons and must not be lo cated or operating in conjunction with any other antenna or trans mitter, except as listed for this product’s certification. Les antennes utilisées pour cet émetteur doit être installé pour fournir une distance de séparation d’au moins 28 cm de toutes les personnes et ne doit pas être situé ou opérant en conjonction avec une autre antenne ou un autre émetteur, sauf dans les cas énumérés à la certifi cation de ce produit. Australia and New Zealand Warning: This is a Class A product. In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures. CE Marking CE marking on this product represents the product is in compliance with all directives that are applicable to it. RoHS/WEEE Compliance Statement English European Directive 2012/19/EU requires that the equipment bearing this symbol on the product and/or its packaging must not be disposed of with unsorted municipal waste. The symbol indicates that this product should be disposed of separately from regular household waste streams. It is your responsibility to dispose of this and other electric and electronic equipment via designated collection facilities appointed by the government or local authorities. Correct disposal and recycling will help prevent potential negative consequences to the environment and human health. For more detailed information about the disposal of your old equipment, please contact your local authorities, waste disposal service, or the shop where you purchased the product. Deutsch Die Europäische Richtlinie 2012/19/EU verlangt, dass technische Ausrüstung, die direkt am Gerät und/oder an der Verpackung mit diesem Symbol versehen ist, nicht zusammen mit unsortiertem Gemeindeabfall entsorgt werden darf. Das Symbol weist darauf hin, dass das Produkt von regulärem Haushaltmüll getrennt entsorgt werden sollte. Es liegt in Ihrer Verantwortung, dieses Gerät und andere elektrische und elektronische Geräte über die dafür zuständigen und von der Regierung oder örtlichen Behörden dazu bestimmten Sammelstellen zu entsorgen. Ordnungsgemäßes Entsorgen und Recyceln trägt dazu bei, potentielle negative Folgen für Umwelt und die menschliche Gesundheit zu vermeiden. Wenn Sie weitere Informationen zur Entsorgung Ihrer Altgeräte benötigen, wenden Sie sich bitte an die örtlichen Behörden oder städtischen Entsorgungsdienste oder an den Händler, bei dem Sie das Produkt erworben haben. Español La Directiva 2012/19/UE exige que los equipos que lleven este símbolo en el propio aparato y/o en su embalaje no deben eliminarse junto con otros residuos urbanos no seleccionados. El símbolo indica que el producto en cuestión debe separarse de los residuos domésticos convencionales con vistas a su eliminación. Es responsabilidad suya desechar este y cualesquiera otros aparatos eléctricos y electrónicos a través de los puntos de recogida que ponen a su disposición el gobierno y las autoridades locales. Al desechar y reciclar correctamente estos aparatos estará contribuyendo a evitar posibles consecuencias negativas para el medio ambiente y la salud de las personas. Si desea obtener información más detallada sobre la eliminación segura de su aparato usado, consulte a las autoridades locales, al servicio de recogida y eliminación de residuos de su zona o pregunte en la tienda donde adquirió el producto. Français La directive européenne 2012/19/UE exige que l’équipement sur lequel est apposé ce symbole sur le produit et/ou son emballage ne soit pas jeté avec les autres ordures ménagères. Ce symbole indique que le produit doit être éliminé dans un circuit distinct de celui pour les déchets des ménages. Il est de votre responsabilité de jeter ce matériel ainsi que tout autre matériel électrique ou électronique par les moyens de collecte indiqués par le gouvernement et les pouvoirs publics des collectivités territoriales. L’élimination et le recyclage en bonne et due forme ont pour but de lutter contre l’impact néfaste potentiel de ce type de produits sur l’environnement et la santé publique. Pour plus d’informations sur le mode d’élimination de votre ancien équipement, veuillez prendre contact avec les pouvoirs publics locaux, le service de traitement des déchets, ou l’endroit où vous avez acheté le produit. Italiano La direttiva europea 2012/19/UE richiede che le apparecchiature contrassegnate con questo simbolo sul prodotto e/o sull’imballaggio non siano smaltite insieme ai rifiuti urbani non differenziati. Il simbolo indica che questo prodotto non deve essere smaltito insieme ai normali rifiuti domestici. È responsabilità del proprietario smaltire sia questi prodotti sia le altre apparecchiature elettriche ed elettroniche mediante le specifiche strutture di raccolta indicate dal governo o dagli enti pubblici locali. Il corretto smaltimento ed il riciclaggio aiuteranno a prevenire conseguenze potenzialmente negative per l’ambiente e per la salute dell’essere umano. Per ricevere informazioni più dettagliate circa lo smaltimento delle vecchie apparecchiature in Vostro possesso, Vi invitiamo a contattare gli enti pubblici di competenza, il servizio di smaltimento rifiuti o il negozio nel quale avete acquistato il prodotto. Declaration of Conformity български [Bulgarian] С настоящото UBIQUITI NETWORKS декларира, че този тип радиосъоръжение UAP-XG е в съответствие с Директива 2014/53/ЕС. Цялостният текст на ЕС декларацията за съответствие може да се намери на следния интернет адрес: www.ubnt.com/compliance Hrvatski [Croatian] UBIQUITI NETWORKS ovime izjavljuje da je radijska oprema tipa UAP-XG u skladu s Direktivom 2014/53/EU. Cjeloviti tekst EU izjave o sukladnosti dostupan je na sljedećoj internetskoj adresi: www.ubnt.com/compliance Čeština [Czech] Tímto UBIQUITI NETWORKS prohlašuje, že typ rádiového zařízení UAP-XG je v souladu se směrnicí 2014/53/EU. Úplné znění EU prohlášení o shodě je k dispozici na této internetové adrese: www.ubnt.com/compliance Dansk [Danish] Hermed erklærer UBIQUITI NETWORKS, at radioudstyrstypen UAP-XG er i overensstemmelse med direktiv 2014/53/EU. EU‑overensstemmelseserklæringens fulde tekst kan findes på følgende internetadresse: www.ubnt.com/compliance Nederlands [Dutch] Hierbij verklaar ik, UBIQUITI NETWORKS, dat het type radioapparatuur UAP-XG conform is met Richtlijn 2014/53/EU. De volledige tekst van de EU-conformiteitsverklaring kan worden geraadpleegd op het volgende internetadres: www.ubnt.com/compliance English Hereby, UBIQUITI NETWORKS declares that the radio equipment type UAP-XG is in compliance with Directive 2014/53/EU. The full text of the EU declaration of conformity is available at the following internet address: www.ubnt.com/compliance Eesti keel [Estonian] Käesolevaga deklareerib UBIQUITI NETWORKS, et käesolev raadioseadme tüüp UAP-XG vastab direktiivi 2014/53/EL nõuetele. ELi vastavusdeklaratsiooni täielik tekst on kättesaadav järgmisel internetiaadressil: www.ubnt.com/compliance Suomi [Finnish] UBIQUITI NETWORKS vakuuttaa, että radiolaitetyyppi UAP-XG on direktiivin 2014/53/EU mukainen. EU‑vaatimustenmukaisuusvakuutuksen täysimittainen teksti on saatavilla seuraavassa internetosoitteessa: www.ubnt.com/compliance Français [French] Le soussigné, UBIQUITI NETWORKS, déclare que l’équipement radioélectrique du type UAP-XG est conforme à la directive 2014/53/UE. Le texte complet de la déclaration UE de conformité est disponible à l’adresse internet suivante: www.ubnt.com/compliance Deutsch [German] Hiermit erklärt UBIQUITI NETWORKS, dass der Funkanlagentyp UAP-XG der Richtlinie 2014/53/EU entspricht. Der vollständige Text der EU-Konformitätserklärung ist unter der folgenden Internetadresse verfügbar: www.ubnt.com/compliance Ελληνικά [Greek] Με την παρούσα ο/η UBIQUITI NETWORKS, δηλώνει ότι ο ραδιοεξοπλισμός UAP-XG πληροί την οδηγία 2014/53/ΕΕ. Το πλήρες κείμενο της δήλωσης συμμόρφωσης ΕΕ διατίθεται στην ακόλουθη ιστοσελίδα στο διαδίκτυο: www.ubnt.com/compliance Magyar [Hungarian] UBIQUITI NETWORKS igazolja, hogy a UAP-XG típusú rádióberendezés megfelel a 2014/53/EU irányelvnek. Az EU-megfelelőségi nyilatkozat teljes szövege elérhető a következő internetes címen: www.ubnt.com/compliance Íslenska [Icelandic] Hér með lýsir UBIQUITI NETWORKS yfir því að UAP-XG er í samræmi við grunnkröfur og aðrar kröfur, sem gerðar eru í tilskipun 2014/53/EU. Fullur texti ESB samræmisyfirlýsing er að finna á eftirfarandi netfangi: www.ubnt.com/compliance Italiano [Italian] Il fabbricante, UBIQUITI NETWORKS, dichiara che il tipo di apparecchiatura radio UAP-XG è conforme alla direttiva 2014/53/UE. Il testo completo della dichiarazione di conformità UE è disponibile al seguente indirizzo Internet: www.ubnt.com/compliance Latvių kalba [Latvian] Ar šo UBIQUITI NETWORKS deklarē, ka radioiekārta UAP-XG atbilst Direktīvai 2014/53/ES. Pilns ES atbilstības deklarācijas teksts ir pieejams šādā interneta vietnē: www.ubnt.com/compliance Lietuvių kalba [Lithuanian] Aš, UBIQUITI NETWORKS, patvirtinu, kad radijo įrenginių tipas UAP-XG atitinka Direktyvą 2014/53/ES. Visas ES atitikties deklaracijos tekstas prieinamas šiuo interneto adresu: www.ubnt.com/compliance Malti [Maltese] B’dan, UBIQUITI NETWORKS, niddikjara li dan it-tip ta’ tagħmir tar-radju UAP-XG huwa konformi mad-Direttiva 2014/53/UE. Id-dikjarazzjoni tal-konformità tista’ tiġi kkonsultata minn www.ubnt.com/compliance Norsk [Norwegian] UBIQUITI NETWORKS erklærer herved at utstyret UAP-XG er i samsvar med de grunnleggende krav og øvrige relevante krav i direktiv 2014/53/EU. Den fulle teksten til EU-samsvarserklæringen er tilgjengelig på følgende internettadresse: www.ubnt.com/compliance Polski [Polish] UBIQUITI NETWORKS niniejszym oświadcza, że typ urządzenia radiowego UAP-XG jest zgodny z dyrektywą 2014/53/UE. Pełny tekst deklaracji zgodności UE jest dostępny pod następującym adresem internetowym: www.ubnt.com/compliance Português [Portuguese] O(a) abaixo assinado(a) UBIQUITI NETWORKS declara que o presente tipo de equipamento de rádio UAP-XG está em conformidade com a Diretiva 2014/53/UE. O texto integral da declaração de conformidade está disponível no seguinte endereço de Internet: www.ubnt.com/compliance Română [Romanian] Prin prezenta, UBIQUITI NETWORKS declară că tipul de echipamente radio UAP-XG este în conformitate cu Directiva 2014/53/UE. Textul integral al declarației UE de conformitate este disponibil la următoarea adresă internet: www.ubnt.com/compliance Slovenčina [Slovak] UBIQUITI NETWORKS týmto vyhlasuje, že rádiové zariadenie typu UAP-XG je v súlade so smernicou 2014/53/EÚ. Úplné EÚ vyhlásenie o zhode je k dispozícii na tejto internetovej adrese: www.ubnt.com/compliance Slovenščina [Slovenian] UBIQUITI NETWORKS potrjuje, da je tip radijske opreme UAP-XG skladen z Direktivo 2014/53/EU. Celotno besedilo izjave EU o skladnosti je na voljo na naslednjem spletnem naslovu: www.ubnt.com/compliance Español [Spanish] Por la presente, UBIQUITI NETWORKS declara que el tipo de equipo radioeléctrico UAP-XG es conforme con la Directiva 2014/53/UE. El texto completo de la declaración UE de conformidad está disponible en la dirección Internet siguiente: www.ubnt.com/compliance Svenska [Swedish] Härmed försäkrar UBIQUITI NETWORKS att denna typ av radioutrustning UAP-XG överensstämmer med direktiv 2014/53/EU. Den fullständiga texten till EU-försäkran om överensstämmelse finns på följande webbadress: www.ubnt.com/compliance Online Resources Support help.ubnt.com Community community.ubnt.com Downloads downloads.ubnt.com Ubiquiti Networks, Inc. 685 Third Avenue, 27th Floor New York, NY 10017 USA www.ubnt.com ©2017 Ubiquiti Networks, Inc. All rights reserved. Ubiquiti, Ubiquiti Networks, the Ubiquiti U logo, the Ubiquiti beam logo, and UniFi are trademarks or registered trademarks of Ubiquiti Networks, Inc. in the United States and in other countries. All other trademarks are the property of their respective owners. AI091417
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.6 Linearized : No Author : A Imaoka Create Date : 2017:09:14 18:38:18-07:00 Modify Date : 2017:10:23 18:38:54+08:00 Language : en-US Tagged PDF : Yes XMP Toolkit : Adobe XMP Core 5.6-c015 84.159810, 2016/09/10-02:41:30 Format : application/pdf Title : UniFi AP XG Quick Start Guide Rights : © 2017 Ubiquiti Networks, Inc. All rights reserved. Subject : UniFi Access Point, UniFi AP XG, UAP-XG, Quad Radio, 10G, Ubiquiti Networks Creator : A Imaoka Metadata Date : 2017:10:23 18:38:54+08:00 Creator Tool : Adobe InDesign CC 2017 (Macintosh) Instance ID : uuid:bb52b8c6-4799-4d8d-bc2d-a43f6db636a4 Original Document ID : xmp.did:F77F11740720681180839ACE20804D07 Document ID : xmp.id:20aa3b2b-8738-4b5e-b89e-abcb34901466 Rendition Class : proof:pdf Derived From Instance ID : xmp.iid:af93f297-0f36-4099-9238-75185bb0f5e6 Derived From Document ID : xmp.did:af93f297-0f36-4099-9238-75185bb0f5e6 Derived From Original Document ID: xmp.did:F77F11740720681180839ACE20804D07 Derived From Rendition Class : default History Action : converted History Parameters : from application/x-indesign to application/pdf History Software Agent : Adobe InDesign CC 2017 (Macintosh) History Changed : / History When : 2017:09:14 18:38:18-07:00 Producer : Adobe PDF Library 15.0 Trapped : False Page Layout : SinglePage Page Count : 32EXIF Metadata provided by EXIF.tools