Uniden America UP320 2.4 GHz Cordless Phone (FHSS) User Manual

Uniden America Corporation 2.4 GHz Cordless Phone (FHSS) Users Manual

Users Manual

QUICK REFERENCE GUIDE [1]www.uniden.comStep 1 Checking the Package ContentsMake sure you have received the following items in the package. If any of these items are missing or damaged, contact the Uniden Parts Department.Base Unit - 1Handset - [1 for DCT648] and [2 for DCT648-2]AC Adapter - [1 for DCT648] and [2 for DCT648-2]Rechargeable Battery Pack - [1 for DCT648] and [2 for DCT648-2]Telephone Cord - 1Beltclip - [1 for DCT648] and [2 for DCT648-2]Extra Charger - 1 for DCT648-2 onlyOwner's Manual - 1Other Printed MaterialUniden Parts Department at (800) 554-3988Hours: M-F 8:00 a.m. to 5:00 p.m. CST.We can also be reached on the web atwww.uniden.comStep 2 Install and Charge the Handset BatteryTO INSTALL THE HANDSET BATTERYRemove the cover.Connect the battery pack connector with the correct polarity and listen for a click to insure connection.Replace the cover.Plug the AC adapter cord into the base unit and then into a 120V AC outlet.Place the handset in the base and charge continuously for 17 - 20 hours before using the phone.Step 3 Connect to Phone LineWhen the handset battery pack is fully charged, after 17-20 hours of charging, plug the telephone cord into the base unit and then into a telephone wall jack.QRG_TEL_lineQRG_battery_packQRG_AC_cordQUICK REFERENCE GUIDE
[2] QUICK REFERENCE GUIDEwww.uniden.comYour phone is set for tone dialing. If your local network requires pulse dialing, please see D. Choose the dialing mode on page 13.Step 4 Setting Caller ID & Language Display OptionsTO SET CALLER ID ON CALL WAITING AND CALL WAITING DELUXEPress menu/del in the standby mode.Press ring/vol/∧ or ring/vol/∨ t o select "Global Setup", and then select/. Press ring/vol/∧ or ring/vol/∨ to select "CIDCW", and then select/.Press ring/vol/∧ or ring/vol/∨ to select "CW On/CWDX On", "CW On/CWDX Off", or "CW Off/CWDX Off", and then select/. TO SET LANGUAGEPress menu/del in the standby mode.Press ring/vol/∧ or ring/vol/∨ to select "Handset Setup", and then select/. Press ring/vol/∧ or ring/vol/∨ to select "Language", and then select/. Press ring/vol/∧ to choose a Language, and then select/.Step 5 Setting Up the Answering SystemTO TURN THE ANSWERING SYSTEM ON/OFFEach time answer on/off is pressed, the answer mode is switched between On and Off.TO SET GREETING MESSAGEPress and hold greeting.Start recordingyour message.Position yourself as nearto the base as possible.When finished,press greeting or play/stop.QRG_setupQRG_answering
[3]www.uniden.comQUICK REFERENCE GUIDE 1WELCOME/FEATURES 4CONTROLS AND FUNCTIONS 6DISPLAY AND ICONS 8GETTING STARTED 9Setting up the Phone 9Mounting the Base Unit on a Wall 14Main Menu Flow Chart 16About the Menu Setup Options 18Setting Up the Menu Setup Options 22BASICS 30Making and Receiving Calls 30Placing a Call on Hold 31Redialing a Call 32Adjusting the Handset Ringer and Earpiece Volume 33Do Not Disturb (DND) 33Mute Microphone 34Tone Dialing Switch-over 34Traveling Out-of-Range 34Clarity Booster 35Privacy Mode 35Intercom/Call Transfer Feature 353-Way Conferencing 36Flash and Call Waiting 36PHONEBOOK 37Steps for Entering Names and Special Characters 39Viewing the Phonebook 41Making Calls Using the Phonebook 42Speed Dialing 42Editing or Erasing a Stored Name, Phone Number, Distinctive Ring, and Speed Dial 43Chain Dialing 44CALLER ID AND CIDCW 45Viewing the Caller ID List 46Deleting a Caller ID Message 47Using the Caller ID Message List 48Call Waiting Deluxe Features 49THE INTEGRATED ANSWERING DEVICE 50Turning the Answering System On/Off 51Setting Up your Answering System 51Using your Answering System 59Remote Option 62 EXPANDING YOUR PHONE 65Connecting the Charger 65Register the Handset 66Using the DirectLink Mode 674-Way Conferencing 68Intercom/Call Transfer Feature 68Replacing the Base 70ADDITIONAL INFORMATION 71Changing the Digital Security Code 71Installing the Beltclip 71Headset Installation 71Note on Power Sources 72Maintenance 72General Information 73TROUBLESHOOTING 74Liquid Damage 77PRECAUTIONS & WARRANTY 78I.C. NOTICE 80INDEX 81MEMORY LIST 82Contents
[4] WELCOME/FEATURESwww.uniden.comCongratulations on your purchase of the Uniden Multi Handset Cordless System telephone. This unit is different from conventional cordless telephones. When the base unit is connected to AC power and a telephone line, it can support up to 4 handsets. Using extra handsets, you can establish a 3-way conference call (2 handsets and an outside line), while two other handsets are making an intercom call. You can now place a fully featured cordless handset anywhere in your home or office where AC power is available to connect the handset chargers.Note: Some illustrations in this manual may differ from the actual unit for explanation purposes.As an Energy Star Partner, Uniden has determined that this product or product models meets the Energy Star guidelines for energy efficiency.Energy Star is a U.S. registered mark.Note: Energy Star applies to DCT646 only. 2.4GHz Frequency Hopping Spread Spectrum Integrated Answerring Device (Trilingual Announcement Option) 4 Multi-Handset Expandability Hands Free Speakerphone in the Handset Call Waiting Deluxe Caller ID/Caller ID On Call Waiting 100 Dynamic Memory Location (Phonebook & Caller ID) Trilingual Function Menus (English-French-Spanish) Intercom/Call Transfer 20 Distinctive Ring Options (10 ringer tones and 10 melody ringers) Mute Feature Flash and Pause 88 Channel Auto Scan Handset to Handset Intercoming DirectLinkTM Mode Room Monitoring Feature Battery Level Indicator Clock DisplayWELCOME/FEATURESWelcomeFeatures
WELCOME/FEATURES [5]www.uniden.comThis series features include AutoTalk and AutoStandby. AutoTalk allows you to answer a call by just removing the handset from the cradle so you don't have to waste time pushing buttons. AutoStandby allows you to hang up by simply returning the handset to the cradle.To protect you against mis-billed calls, which might result from your phone being activated by other equipment, this series has Random Code digital security, which automatically selects one of over approx. 130,000 digital security codes for the handset and base.Frequency Hopping Spread Spectrum (FHSS) technology improves calling range and clarity, and eliminates cross talk. Because it rapidly changes transmission frequencies within the 2.4GHz bandwidth, this cordless phone helps reduce the possibility of eavesdropping.DirectLink mode is used when you have 2 or more handsets. You can use your handsets as transceivers.Be sure to visit our web site: www.uniden.comUniden is a registered trademark of Uniden America Corporation.AutoTalk, AutoStandby, DirectLink, and Random Code are trademarks of Uniden America.Standby Mode - The handset is not in use, The handset may be on or off the base, but talk/flash key has been pressed.Talk Mode - The handset is not in the cradle and talk/flash or speaker has been pressed enabling a dial tone. "Talk" appears on the display.WELCOME/FEATURES
[6] CONTROLS & FUNCTIONSwww.uniden.comControls & Functions1. Handset Antenna2. Headset Jack Cover3. Beltclip Hole4. Hands Free Speaker5. Handset Battery Compartment6. New Message LED7. Handset Earpiece8. LCD Display9. Menu/del (delete) Key (P. 22 / P. 32, 47)10. /vol and ∧/∨ (P. 16-17, P. 33 / 37) a. ringer and volume control b. scroll keys for display screen11. |<<(repeat)/1 Key12. ∅(delete)(for remote operation)/4 Key13. */tone/< Key (P. 30, 35 / P. 67-68)14. redial/pause Key (P. 32/ P. 24)15. speaker Key (P. 24, 30, 42)16. Select/ (voice mail) Key (P. 22-29, 37-49)17. Call id (Caller ID) key (P. 45-49)18. Talk/flash Key (P. 30 / P. 36)19. End Key (P. 30, 35-36)20. (play)/2 Key21. >>|(skip)/3 Key22. (stop)/5 Key23. #/> Key (P. 30 / P. 39)24. (Phonebook) Key (P. 37-41)25. Hold/transfer/int'com (Intercom) Key (P. 31 / P. 69 / P. 68)26. Handset Microphone27. Handset Charging ContactsCONTROLS & FUNCTIONS
CONTROLS & FUNCTIONS [7]www.uniden.com28. Base Speaker29. ∅/delete Key (P. 52, 60)30. Charge LED31. Message Counter Display32. In use LED33. Play/stop Key (P. 53)34. Base Antenna35. |<<(repeat)/SELECT Key (P. 60)36. Clock/MENU Key (P. 53)37. Greeting Key (P. 51)38. Answer on/off Key (P. 51)39. /vol and ∧/∨ (P. 52)40. Base Charging Contacts41. >>|(skip)/SELECT Key42. SET Key (P. 53)43. Do not disturb Key (P. 33)44. Memo record Key (P. 61)45. Mute Key (P. 34)46. Hold Key (P. 31)47. Intercom/find handset Key (P. 35)48. Speaker Key/speaker LED (P. 30)49. Microphone50. DC Power Input51. Telephone InputFor DCT648-2 only52. DC Power Input53. Charging Contacts54. Charge LEDCONTROLS & FUNCTIONS
GETTING STARTED [9]www.uniden.comSetting up the PhoneDo the following steps:A. Choose the best locationB. Install the battery pack into the handsetC. Install the rechargeable battery pack into the handset D. Choose the dialing modeA. Choose the best locationBefore choosing a location for your new phone, read Installation Considerations on page 79. Here are some important guidelines you should consider:If your home has specially wired alarm equipment connected to the telephone line, be sure that installing the system does not disable your alarm equipment. If you have questions about what will disable alarm equipment, contact your telephone company or a qualified installer.noteGETTING STARTED
[10] GETTING STARTEDwww.uniden.comB. Install the rechargeable battery pack into the handsetThe handset is powered by a rechargeable battery pack. The battery recharges automatically when the handset is placed in the base unit.Charge the handset battery pack for at least 17-20 hours before using your new cordless telephone for the first time! To maximize the charge capacity of your battery pack, DO NOT plug the telephone cord into the base unit and wall jack until the battery is fully charged.1) Press down on the handset battery case cover (use the finger indention for a better grip) and slide the cover downward to remove.2) Plug the battery pack connector (red & black wires) into the small, black jack inside the battery compartment. (The connector notches fit into the grooves of the jack only one-way.) Match the wire colors to the polarity label in the battery compartment, connect the battery, and listen for a click to insure connection.3) Make sure you have a good connection by slightly pulling on the battery wires. If the connection is secure, the battery jack will remain in place.4) Place the battery case cover back on the handset by sliding it upwards until it clicks into place.5) Place the handset in the base unit for 17-20 hours without interruption. The base unit's LED light (labeled charge) illuminates once the handset is placed in the base. The LED light will illuminate whether the battery pack is connected or not.If the base charge/in use LED light does not illuminate: Check to see if the AC adapter is plugged into the base unit and the electrical wall outlet properly. (Use only the supplied AC adapter. Do not use any other AC adapter.) Check to see if the handset is sitting correctly in the base and making good contact with the base unit's charging contacts.Use only the Uniden (BT-446) rechargeable battery pack supplied with your cordless telephone.Replacement battery pack are also available through the Uniden Parts Department at (800) 554-3988, Monday thru Friday from 8:00 a.m. to 5:00 p.m. or online at www.uniden.comnotebattery_pack
GETTING STARTED [11]www.uniden.comLow battery alertWhen the battery pack is very low and need to be charged, the phone is programmed to eliminate functions in order to save power.The battery pack needs to be charged when:- The empty battery icon appears.- "Low Battery" appears in the display.If the phone is in the standby mode, none of keys will operate. If you are on a call, complete your conversation as quickly as possible, and return the handset to the cradle.Cleaning the battery charging contactsTo maintain a good charge, it is important to clean the charging contacts on both the handset and the base unit once a month. Using water only, dampen a cloth to clean the charging contacts. Then make sure to go back over the charging contacts with a dry cloth before returning the handset to the base to charge.Caution: Do not use paint thinner, benzene, alcohol, or other chemical products. Doing so may discolor the surface of the telephone and damage the finish.Even when the battery pack is not being used, it will gradually discharge over a long period of time. For optimum performance, be sure to return the handset to the base unit after a telephone call.Standby Mode - The handset is not in use. The handset may be on or off the base, but talk/flash ke y has been pressed.Talk Mode - The handset is not in the cradle and talk/flash or speaker has been pressed enabling a dial tone. "Talk" appears on the display.noteGETTING STARTEDcleaning
[12] GETTING STARTEDwww.uniden.comC. Connect the base unit1) Connect the AC adapter to the DC IN 9V jack and to a standard 120V AC wall outlet.2) Set the base on a desk or tabletop, and place the handset in the base unit.3) Raise the antenna to a vertical position.4) Make sure that the charge/in use LED illuminates.If the LED does not illuminate, check to see that the AC adapter is plugged in and the handset makes good contact with the base charging contacts.Connect the AC adapter to a continuous power supply. Place the base unit close to the AC outlet so that you can unplug the AC adapter easily. After installing the battery pack in the handset, charge your handset at least 17-20 hours before plugging into the phone line.5) Once the handset battery pack is fully charged, connect the telephone line cord to the TEL LINE jack and to a telephone outlet. If your telephone outlet isn't modular, contact your telephone company for assistance.Use only the supplied [AD-xxxx] AC adapter. Do not use any other AC adapter.Place the power cord so that it does not create a trip hazard or where it could become chafed and create a fire or electrical hazard.noteAC_cordbattery_chargeTEL_line
GETTING STARTED [13]www.uniden.comD. Choose the dialing modeMost phone systems use tone dialing, which sends DTMF tones through the phone lines. However some phone systems still use pulse dialing such as in rural areas. The default setting is tone dialing. Depending on your dialing system, set the dial mode. To set the dial mode, see Setting the Dial Mode on page 26. If you are not sure of your dialing system, set the unit to tone dialing. Make a trial call. If the call connects, leave the setting as is, otherwise set the unit to pulse dialing. If your phone system requires pulse dialing and you need to send DTMF tones in certain situations during a call, you may Switch Over to tone dialing. (Refer to Tone Dialing Switch-over on page 34.)GETTING STARTED
[14] GETTING STARTEDwww.uniden.comMounting the Base Unit on a WallStandard wall plate mountingThis phone can be mounted on any standard wall plate.1) Snap the wall mount adapter into the notches on the base top.2) Plug the AC adapter into the DC IN 9V jack.3) Wrap the AC adapter cord inside the molded wiring channel as shown.4) Plug the AC adapter into a standard 120V AC wall outlet.5) Plug the telephone line cord into the TEL LINE jack. Wrap the cord inside the molded wiring channel as shown.6) Plug the telephone line cord into the telephone outlet.7) Raise the antenna to a vertical position.8) Align the mounting slots on the base with the mounting posts on the wall. Then push in and down until the phone is firmly seated.wall_mount_adapterwall_mountDO NOT use an AC outlet controlled by a wall switch.!GETTING STARTED
GETTING STARTED [15]www.uniden.comDirect wall mountingIf you don't have a standard wall plate, you can mount your phone directly to the wall. Before doing this, consider the following: Avoid electrical cables, pipes, or other items behind the mounting location that could cause a hazard when inserting screws into the wall. Try to mount your phone within 5 feet of a working phone jack to avoid excessive lengths. Make sure the wall material is capable of supporting the weight of the base and handset. Use #10 screws (minimum length of 1-3/8 inches) with anchoring devices suitable for the wall material where the base unit will be placed.1) Insert two mounting screws into the wall (with their appropriate anchoring device), 3-15/16 inches apart. Allow about 1/8 of an inch between the wall and screw heads for mounting the phone.2) Refer to steps 1 through 8 on page 14 to mount the telephone. Wall_screwGETTING STARTED
[16] GETTING STARTEDwww.uniden.comMenu/del ring/vol/∧orring/vol/∨ring/vol/∧orring/vol/∨ring/vol/∧orring/vol/∨ring/vol/∧orring/vol/∨select/select/select/select/select/talk/flashPress menu/del,and then select/• From the standby mode:Access the voice mail dial (see page 36).Go to DirectLink operation (see pages 22, 67).Setup the menu(see page 22).Monitor the room where the handset is installed.(see page 23).Press end to finish the Room Monitor.Normal standby modeThis is example, if you have handset #1 and #2.GETTING STARTEDMain Menu Flow Chart
GETTING STARTED [17]www.uniden.comring/vol/∧orring/vol/∨ring/vol/∧orring/vol/∨ring/vol/∧orring/vol/∨ring/vol/∧orring/vol/∨select/select/select/select/• From the Talk mode:Setup the menu(see page 29).Setup the menu(see page 27).menu/delselect/Perform the operation.The CWCX appears only when the caller ID setup is set to CW On / CWDX On.GETTING STARTED
[18] GETTING STARTEDwww.uniden.comAbout the Menu Setup OptionsThere are 6 main menu setup options, (DirectLink Mode, Room Monitor, Handset Setup, Answ. Setup, Global Setup, and System Reset) and 16 submenu setup options.Summary of Main Menu Setup Options and Submenu Setup OptionDirectLink Mode DirectLink Mode allows a pair of handsets to work without the base unit, allowing handset-to-handset communication. Use them at sporting events or while shopping to stay in contact with family members or friends. You must set the two handsets to DirectLink Mode to utilize this feature.Room MonitorThis feature only works if you have two or more handsets, allowing you to monitor sounds in another room, (see page 23 for setup). One handset is placed in the desired room to monitor (acts as remote mic), and the other is placed near listener (remote speaker). This is useful for monitoring child activities.For Global Setup, and System Reset menu setup option, make sure the line is not in use, and the handsets are within the range limits of the base.noteGETTING STARTED
GETTING STARTED [19]www.uniden.comHandset SetupThe following submenu options must be set separately for each handset.Submenu option DescriptionRinger Tones Adjusting the ringer tone (see page 23).Distinct. RingSet the distinctive ring (see page 24). "Distinctive Ringer" allows you to (Distinctive ring) preset memory locations with a designated ring tone. When an incoming call is received and the Caller ID information matches the information in one of the memory locations, the distinctive ring that has been stored for that particular Caller will sound. If you have set multiple memory locations with distinctive rings, switching the setting to "Distinctive Off" will result in no distinctive ringing. All incoming calls will have a normal ring tone. Switching to "Distinctive On" will activate all programmed distinctive ring memory locations.AutoTalkAllows you to answer the phone without pressing talk/flash or speaker. When the AutoTalk is set to On, simply remove the handset from the cradle and the phone automatically answers the call (see page 24).Anykey AnswerAllows you to answer the phone without pressing talk/flash or speaker. When the Anykey Answer is On, you can answer a call by pressing any number key, */tone/<, or #/> on the handset (see page 24).Banner (True Banner)Customize the name of your handset, and display it in the LCD. While intercom, intercom hold, Room Monitor, and Copy Phonebook operation, your banner will be displayed on the receiving handset. (see page 24).Language Language option can be used to choose the language of your display. You can select from English, French, or Spanish (see page 25).Key Touch Tone Set your phone's key touch-tone to On or Off (see page 25).GETTING STARTED
[20] GETTING STARTEDwww.uniden.comAnswering SetupThis menu allows you to set up TAD settings from your handset. You can also set these setup menus from the base (see page 51).Submenu option DescriptionSecurity CodeSelect a two-digit Personal Identification Number (PIN) code. A PIN code is required to play your messages from a remote location, you will need to enter a two-digit PIN code (see page 25).Ring TimeAllows you to set the number of rings the caller hears before your answering system plays the outgoing message. You can set the ring time to answer after two, four, or six rings. Setting "TS" (Toll Saver), the answering system picks up after two rings if you have new messages, and after four rings if there are none (see page 26).Record TimeSet the duration for recording the incoming messages. You have three record time options. The options "1 minute" or "4 minutes" set the duration for recording the incoming messages. "Announce only" answers the call with the preset greeting or your personal greeting but prevents the caller from leaving a message (see page 26).Message Alert Lets you know when you have a new incoming message by sounding a short alert tone (see page 26).Language Select the Language of your answering system announcements from English, French, or Spanish (see page 26).Language Language option can be used to choose the language of your display. You can select from English, French, or Spanish (see page 25).Call Screen Set the call-screening feature to On or Off (see page 26).GETTING STARTED
GETTING STARTED [21]www.uniden.comGlobal SetupIf you change one of the Global settings, you change the setting for all addititonal handsets. Only one handset can change Global settings at a time.System ResetSystem Reset is used to clear the handset's ID from the main base unit, or the base ID from the handset.Submenu option DescriptionDay & time Set the day and time of your display (see page 27).CIDCWSet the Caller ID on Call Waiting (CIDCW) setting. CIDCW performs the same as regular Caller ID on call waiting number (see page 25). Call Waiting Deluxe allows you to handle call waiting calls in seven different ways (see page 27).Area CodeStore or edit the area code. If you enter a 3-digit area code number in the"Area Code" option, your local area code does not appear in the Caller ID message. For calls received from outside your local area code, you will see a full 10-digit number (see page 28). Note: If your calling area requires 10-digit dialing, do not program this option. Dial Mode Set the dial mode to tone or pulse (see page 28).Copy Phonebook Allow you to transfer the phonebook data stored in one handset to another handset (see page 28).Voice Mail ToneIf your service does not support SDT message signal, it allows you to set your VMWI (Visual Message Waiting Inculcator) not to detect SDT message signal (see page 29).Submenu option DescriptionDeregister HS Clear the handset ID from the base. Use this option, for example when you change the digital security code (see page 29).Replacing BaseClear the base ID. Use this option, for example, if you wish to deregister the base to use the handset with another base of the DSS series (DCT646/DCT6465/DCT648/DCT6485 series) (see page 29).GETTING STARTED
[22] GETTING STARTEDwww.uniden.comSetting Up the Menu Setup OptionsEntering Menu Setup Option1) Press the menu/del key in the standby mode.2) Use ring/vol/∧ or ring/vol/∨ to move the pointer to a desired main menu setup option (DirectLink Mode, Room Monitor, Handset Setup, Answ. Setup, Global Setup, and System Reset).3) Press select/ to select the desired main menu setup option.4) Use ring/vol/∧ or ring/vol/∨ to select a desired submenu setup option, and then press select/ to enter.In the submenu setup option, ring/vol/∧ or ring/vol/∨ is used to select an item. Press select/ to confirm your selection. For detailed instructions, see the following sections for the desired submenu.5) To exit the menu, press end or place the handset to the cradle.DirectLink ModeUsing the DirectLink Mode1) Enter the "DirectLink Mode" menu option (see "Entering Menu Setup Option" on page 22). "To enter DirectLink mode press SELECT" appears.2) Press select/ to enter the DirectLink mode. You will hear a confirmation tone, and "DirectLink Mode Complete" appears.3) To return back to the normal mode, exit the DirectLink mode. To exit the DirectLink mode, press menu/del, and then select, or return the handset to the cradle.GETTING STARTED
GETTING STARTED [23]www.uniden.comRoom Monitor1) Enter the "Room Monitor" menu option (see "Entering Menu Setup Option" on page 22). "To Room Monitor" appears.2) Select the handset you want to monitor by using ring/vol/∧ or ring/vol/∨.3) Press select/. "RoomMonitor" appears and you hear sounds in the room where the handset is installed.4) To finish the Room Monitor, press end or return the handset to the cradle.Handset SetupSelecting a Ringer Tone1) Enter the "Handset Setup" menu option, and then the "Ringer Tones" submenu option (see "Entering Menu Setup Option" on page 22).There are 10 ringer tones or 10 melodies to choose from.- Ringers [Flicker, Clatter, Soft Alert, Wake Up, Light Bug, Beep Boop, Tone Board, Chip Chop, Party Clap, Reminder]- Melodies [Beethoven's Symphony #9 (Beethoven9), For Elise (Elise), We Wish You A Merry Christmas (Merry- Xmas), Home Sweet Home (Hm Swt Hm), Lorri Song #6 (Lorri Song), When the Irish Eyes Are Smiling (Irish Eyes), Aura Lee, Let Me Call You Sweet Heart (Sweetheart), Star Spangled Banner(Star Spangle), Old MacDonald(Old MacDld)]2) Press ring/vol/∧ or ring/vol/∨ to move the pointer. You will hear the ringer or melody as you scroll through the options.3) Press select/. You will hear a confirmation tone.This is an example, if you have handset #1 and #2.noteGETTING STARTED
[24] GETTING STARTEDwww.uniden.comDistinctive Ringer Setup1) Enter the "Handset Setup" menu option, and then the "Distinct. Ring" submenu option (see "Entering Menu Setup Option" on page 22).2) Press ring/vol/∧ or ring/vol/∨ to select "On" or "Off".3) Press select/. You will hear a confirmation tone.Setting the AutoTalk1) Enter the "Handset Setup" menu option, and then the "Auto Talk" submenu option (see "Entering Menu Setup Option" on page 22).2) Press ring/vol/∧ or ring/vol/∨ to change the selection, "On" or "Off".3) Press select/. You will hear a confirmation tone.Setting the Anykey Answer1) Enter the "Handset Setup" menu option, and then the "Anykey Answer" submenu option (see "Entering Menu Setup Option" on page 22).2) Press ring/vol/∧ or ring/vol/∨ to change the selection, "On" or "Off".3) Press select/. You will hear a confirmation tone.Setting the True Banner1) Enter the "Handset Setup" menu option, and then the "Banner" submenu option (see "Entering Menu Setup Option" on page 22).2) Use the number keypad (0-9), */tone/<, #/>, or menu/del to enter or edit the name.3) Press select/. You will hear a confirmation tone. GETTING STARTED
GETTING STARTED [25]www.uniden.comSelecting a Language1) Enter the "Handset Setup" menu option, and then the "Language" submenu option (see "Entering Menu Setup Option" on page 22).2) Press ring/vol/∧ or ring/vol/∨ to choose English, French (Français), or Spanish (Español).3) Press select/. You will hear a confirmation tone.Setting the Key Touch Tone1) Enter the "Handset Setup" menu option, and then the "Key Touch Tone" submenu option (see "Entering Menu Setup Option" on page 22).2) Press ring/vol/∧ or ring/vol/∨ to change the selection, "On" or "Off".3) Press select/. You will hear a confirmation tone.Answering System SetupSetting a PIN Code1) Enter the "Answ. Setup" menu, and then the "Security Code" submenu (see "Entering Menu Setup Option" on page 22).2) Enter a two-digit PIN code (01-99) using the number keypad (0-9).3) Press select/. You will hear a confirmation tone.For Answering Setup menu, you can also set them from the base (see page 51).noteGETTING STARTED
[26] GETTING STARTEDwww.uniden.comSetting the Ring Time1) Enter the "Answ. Setup" menu option, and then the "Ring Time" submenu option (see "Entering Menu Setup Option" on page 22).2) Press ring/vol/∧ or ring/vol/∨ to select a Ring Time (Toll Saver, 2 Times, 4 Times, or 6 Times).3) Press select/. You will hear a confirmation tone.Setting the Record Time1) Enter the "Answ. Setup" menu option, and then the "Record Time" submenu option (see "Entering Menu Setup Option" on page 22).2) Press ring/vol/∧ or ring/vol/∨ to select Record Time (1 Minute, 4 Minutes, or Announce Only).3) Press select/. You will hear a confirmation tone.Setting the Message Alert On or Off1) Enter the "Answ. Setup" menu option, and then the "Message Alert" submenu option (see "Entering Menu Setup Option" on page 22).2) Press ring/vol/∧ or ring/vol/∨ to choose "On" or "Off".3) Press select/. You will hear a confirmation tone.Setting the Language of your Answering System1) Enter the "Answ. Setup" menu option, and then the "Language" submenu option (see "Entering Menu Setup Option" on page 22).2) Press ring/vol/∧ or ring/vol/∨ to choose English, French (Français), or Spanish (Español).3) Press select/. You will hear a confirmation tone.GETTING STARTED
GETTING STARTED [27]www.uniden.comSetting the Call Screen1) Enter the "Answ. Setup" menu option, and then the "Call Screen" submenu option (see "Entering Menu Setup Option" on page 22).2) Press ring/vol/∧ or ring/vol/∨ to choose "On" or "Off".3) Press select/. You will hear a confirmation tone.Global SetupSetting Day and Time1) Enter the "Global Setup" menu option, and then the "Day & Time" submenu option (see "Entering Menu Setup Option" on page 22).2) Press ring/vol/∧ or ring/vol/∨ to select the day of the week, and then press select/.3) Press ring/vol/∧ or ring/vol/∨ to set the time, and then press select/. 4) Press ring/vol/∧ or ring/vol/∨ to set minute, and then press select/.5) Press ring/vol/∧ or ring/vol/∨ to choose "AM" or "PM", and then press select/. You will hear a confirmation tone.Setting CIDCW (Caller ID on Call Waiting)1) Enter the "Global Setup" menu option, and then the "CIDCW" submenu option (see "Entering Menu Setup Option" on page 22).2) Press ring/vol/∧ or ring/vol/∨ to select "CW On/CWDX On", "CW On/CWDX Off", or "CW Off/CWDX Off", and then press select/. You will hear a confirmation tone.When a Global setting is changed from one handset, this affects all registered handsets.For setting the Day and Time, the idle time-out is extended to 2 minutes.noteGETTING STARTED
[28] GETTING STARTEDwww.uniden.comSetting the Area Code1) Enter the "Global Setup" menu option, and then the "Area Code" submenu option (see "Entering Menu Setup Option" on page 22).2) Press the number keypad (0-9) to enter a 3-digit area code.3) Press select/. You will hear a confirmation tone.Setting the Dial Mode1) Enter the "Global Setup" menu option, and then the "Dial Mode" submenu option (see "Entering Menu Setup Option" on page 22).2) Press ring/vol/∧ or ring/vol/∨ to change the selection, "Tone" or "Pulse" (the initial setting is Tone).3) Press select/. You will hear a confirmation tone.Copy Phonebook1) Enter the "Global Setup" menu option, and then the "Copy Phonebook" submenu option (see "Entering Menu Setup Option" on page 22).2) Press ring/vol/∧ or ring/vol/∨ to choose "One memory" or "All Memory", and then press select/.If you choose "All Memory", "Are you sure?" appears on the handset. Go to step 4.3) Press ring/vol/∧ or ring/vol/∨, or the number keypad (0-9) to select the phonebook location you want to export, and then press select/. 4) Press ring/vol/∧ or ring/vol/∨ to select the handset to which you want transfer the phonebook locations, and then press select/. The phonebook locations will be transferred to the handset. On the receiving handset, "Receiving Handset" appears. When the transfer complete, "Done!" appears on the handset.When the area code has already been stored in memory, the stored area code will be displayed. To change it, use menu/del and number keys to enter the new area code.If you receive a call, the transfer will be canceled.If an error occurs, the phonebook locations transferred before the error were stored in the receiving handset. "Unavailable" appears on the display.note
GETTING STARTED [29]www.uniden.comVoice Mail Tone (Block from SDT message signal)1) Enter the "Global Setup" menu option, and then the "Voice Mail Tone" submenu option (see "Entering Menu Setup Option" on page 22). 2) Press ring/vol/∧ or ring/vol/∨ to set the voice message indication (SDT message signal) to "On" or "Off".3) Press select/. You will hear a confirmation tone.System ResetDe-register the Handset1) Enter the "System Reset" menu option, and then the "Deregister HS" submenu option (see "Entering Menu Setup Option" on page 22).2) Press ring/vol/∧ or ring/vol/∨ to select the handset ID to be de-registered from the list, and then press select/. "Deregister HS?" appears.3) Press select/. You will hear a confirmation tone.When de-registration is complete, "Deregistration Complete" appears.4) After de-registering the handset, move to "Replacing the Base Setting" below.Replacing the Base Setting1) Enter the "System Reset" menu option, and then the "Replacing Base" submenu option (see "Entering Menu Setup Option" on page 22). "Replace Base?" appears.2) Press select/. You will hear a confirmation tone.The base information will be deleted.When replacing the base is complete, "Place the handset on main base to register" appears, register the handset(s) to the new base (see page 66).GETTING STARTED
[30] BASICSwww.uniden.comMaking and Receiving CallsFrom the HandsetThis handset has a built-in speakerphone that allows you to have a "hands-free conversation." This feature allows you to easily communicate while performing other tasks, such as cooking. (speaker icon) appears during hands-free conversations.You can easily switch a call from normal conversation to "hands-free conversation".To switch a call, press speaker during the call.From the HandsetNormal conversation Hands-free conversationTo answer a callHandset On the CradlePick up the handset (AutoTalk) or pick up the handset and press talk/flash.Handset Off the CradlePress any number key,*/tone/<, or #/> (Any Key Answer), or press talk/flash.Handset Off the CradlePress speaker.To make a callHandset Off the Cradle1) Press talk/flash.2) Listen for the dial tone.3) Dial the number.ORDial the number, and then press talk/flash.Handset Off the Cradle1) Press speaker.2) Listen for the dial tone.3) Dial the number.ORDial the number, and then press speaker.To hang up Press end, or return the handset to the cradle (AutoStandby).To enter a pause within the dialing sequenceWhen you dial the number in the standby mode, press redial/pause. "P" appears in the display, which represents a pause.To set "Autotalk", see page 24 or "Anykey Answer" see page 24.The handset microphone is located at the bottom of the handset (see "Controls and Functions" on page 6). Position yourself as near to the handset as possible and speak clearly.If the line is in use by another handset(s), "Line In Use" appears in all registered handset's display, that are not in use.noteBASICS
BASICS [31]www.uniden.comFrom the Base (Receiving calls only)1) Press speaker and begin speaking.2) To hang up, press speaker.Placing a Call on Hold1) During a call, press hold/transfer/intcom. The call will be put on hold.Once 10 seconds has passed or when you press the end key, the call will be put on hold.2) To talk to the caller, press talk/flash or speaker on a handset. The phone will return back to the call.Receiving_callThe base microphone is located under the base (see "Controls and Functions" on page 7). Position yourself as near to the base as possible.You can hold a call for 5 minutes, when 5 minutes has passed, the call is disconnected and the phone returns to the standby mode.While a call is on hold, CIDCW can not be received.noteBASICS
[32] BASICSwww.uniden.comRedialing a CallThe last three phone numbers dialed can be quickly redialed.Redialing from Standby Mode1) Press redial/pause in the standby mode.2) Press redial/pause again. Each press of redial/pause will display one of the last three number redialed.3) Press talk/flash or speaker. The selected number is dialed.4) To hang up, press end.Redialing from Talk Mode1) Press talk/flash or speaker.2) Press redial/pause. The last number dialed will be displayed and redialed. To hang up, press end.Deleting a Redial Record1) Press redial/pause in the standby mode.2) Press redial/pause repeatedly to display the number to be deleted.3) Press menu/del.4) Press ring/vol/∧ or ring/vol/∨ to choose "Yes."5) Press select/. The redialed number is deleted.Storing a Redial Record1) Press redial/pause in the standby mode.2) Press redial/pause repeatedly to display the number to be stored.3) Press select/. "Store/Edit Name" appears.4) To complete the setting, follow the steps 5-9 in "Storing Phone Numbers, Names, Distinctive Rings, and Speed dial" on page 37.redial/pauseredial/pauseredial/pauseIf the number exceeds 32 digits, only the first 32 digits are retained in redial memory.If the redial memory is empty, you will hear a beep.noteBASICS
BASICS [33]www.uniden.comAdjusting the Handset Ringer and Earpiece VolumeHandset ringer tone and volumePress the volume up key or volume down key (labeled as ring/vol/∧ or ring/vol/∨ in standby mode to select one of three ringer volume (Off, Low, or High).Earpiece volumePressing the volume up key or volume down key (labeled as ring/vol/∧ or ring/vol/∨ key) during a call will change the earpiece volume of the handset. This setting will remain in effect after the telephone call has ended.Do Not Disturb (DND)DND allows you to mute the ringer of the handset and the base at once. Additionally, if you have more than one handset, ringer for all handsets will be muted. To do this, In the standby mode, press do not distur on the base. You will hear a confirmation tone and the DND LED right. To cancel ringer mute, Press do not distur again. You can also mute the ringer tone while the phone is ringing by pressing do not distur on the base.To mute the ringer tone temporarily, when the phone is ringing:- Press end on a handset, or- Press pla /stop on the base.The ringer tone will return to the previous setting starting with the next incoming call.ring/vol/∨ring/vol/∧Standby Mode - The handset is not in use. The handset may be on or off the base, but talk/flash key has not been pressed.When you press volume up key (ring/vol/∧) in the maximum volume level or volume down key (ring/vol/∨) in the lowest volume level, an error tone sounds.Setting the DND to On while the answering system Off, turns the Answering system on automatically. The Answering system setting will return to the original setting when you cancel the DND.If you press ans eron/off when the DND and the answering system is On, both of the DND and the answering system will turn Off.noteBASICS
[34] BASICSwww.uniden.comMute MicrophoneWith the handsetYou can temporarily turn Off the microphone so that the person you are talking with cannot hear you. During a telephone call press menu/del to turn Off the microphone. "Mute On" and (mute icon) appear in the display. To cancel muting, repeat above step again when Mute is set to On, "Mute Off" appears.With the baseWhile using the base speakerphone, press mute on the base to turn Off the microphone. Press mute again or press speaker to cancel muting.Tone Dialing Switch-overSome telephone companies use equipment that requires pulse dialing (sometimes referred to as rotary dialing). If you need to enter tone dialing digits, you can switch-over to tone dialing during the call. For example, entering your bank account number after you have called your bank. Initially make your call with the pulse dialing mode. Once your call connects, press */tone/<. Enter the desired number. These digits will be sent as tone dialing. Once the call ends,the tone mode is canceled and pulse dialing mode resumes.Traveling Out-of-RangeDuring a call, as you begin to move your handset too far from your base unit, noise may increase. If you pass the range limits of the base unit, you will hear a beep and "Out of Range" appears, and then the handset returns to the standby mode. You may return back to the call if you move your handset within the range limits of the base, and press talk/flash or speaker within 30 seconds.Tone_dialThe tone feature only applies when the dial mode is set to pulse.This special number can be stored in a memory location. This is referred to as Chain Dialing (see page 44).noteBASICS
BASICS [35]www.uniden.comClarity BoosterIf you encounter interference while using your phone, you can manually improve the sound quality by pressing the Clarity Booster. This works only when the phone is in use.1) Press menu/del.2) Select ring/vol/∧ or ring/vol/∨ to move the pointer to "Clarity Booster", and then select/."Booster On" and "B" appear in the display.To turn Off the Clarity Booster, repeat above step again when the Clarity Booster is On, "Booster Off" appears. Privacy ModePrivacy Mode allows you privacy, and guarantee of no interruption from other registered handsets. 1) Press menu/del.2) Select ring/vol/∧ or ring/vol/∨ to move the pointer to "Privacy Mode", and then select/."Privacy Mode On" and " " appear in the display. Other handsets will display which handset is set to Privacy Mode.To exit the Privacy Mode, repeat above step again when the Privacy Mode is On. "Privacy Mode Off" appears.Intercom/Call Transfer FeatureIntercom and transfer features are available for your phone. See "Intercom/Call Transfer Feature" on page 68 for details.BASICS
[36] BASICSwww.uniden.com3-Way ConferencingThe phone permits 3-way conversations between the handset, base, and an outside line.When speaking on the handset1) Press speaker on the base to initiate the 3-way conversation.2) To hang up, press speaker on the base. The handset will still be connected to the call.When speaking on the base1) Press talk/flash or speaker on the handset to initiate the 3-way conversation.2) To hang up, return the handset to the cradle, or press end key on the handset. The base will still be connected to the call.If you have more than one handset, the phone permits 4-way conversations, see "4-way Conferencing" on page 68 for details.Flash and Call WaitingIf you have Call Waiting service and a call waiting tone sounds while you are on a call, press talk/flash to accept the waiting call. There is a short pause, and then you will hear the new caller. To return to the original caller, press talk/flash again.New Message LEDThe new message LED on the handset is designed to work with your answering system. The LED flashes when you have new messages in your answering system. The LED stops flashing when all new messages are played back (see "Using your Answering System" on page 59)Receiving_call3_way_handtalk_flashYou must subscribe through your local telephone company to receive Call Waiting or Caller ID on call waiting service.noteBASICS
PHONEBOOK [37]www.uniden.comPhonebookPhonebook allows you to dial a number using just a few key presses. Your phone stores names/numbers in the phonebook memory location, and you can search names in alphabetical order. You have a total of 100 locations that can be used for the phonebook (including the Speed dials) and Caller ID messages.1) When the phone is in the standby mode, press phonebook.The handset displays the following items:(1st line) The number of the phonebook locations used(2nd line) How to search (press the number keypad, ring/vol/∧ or ring/vol/∨)(3rd line) How to enter the storing operation (press the select/ key)2) Press select/, "Store/Edit Name" appears.3) Enter the name (up to 16 characters) by using the number keypad (see the "Steps for Entering Names and Special Characters" on page 39).If a name is not required, go to step 5. <No Name> will be used as the name.4) Press select/ to store the name,"Store/Edit No." appears.5) Press the number keypad to enter the phone number (up to 20 digits), press select/ to store the number.6) "Distinctive Ring" appears. Press ring/vol/∧ or ring/vol/∨ to move the pointer to one of the Distinctive Ring options, and then press select/.You have a total of 100 locations. However, Caller ID messages and Phonebook share the memory locations.Selecting a speed dial location where a number is already stored, releases the old number's speed dial setting. The new number will be stored in the speed dial location.When the memory is full, you will hear a beep and "Memory Full" appears. You cannot store names and numbers.The pause key counts as one digit. Pressing redial/pause more than once increases the length of the pause between numbers. Each pause represents a 2 second delay.notePHONEBOOK
[38] PHONEBOOKwww.uniden.comIf you choose not to store a "Distinctive Ring", simply select the "No Selectn" option.7) "Speed Dial" appears. Press ring/vol/∧ or ring/vol/∨ to move the pointer to select the Speed dial location (10 locations: SPD1-SPD0).If you choose not to store the name/number as a Speed Dial, simply select the "No Selectn" option.8) Press select/. You will hear a confirmation tone and "Done!" appears in the display.PHONEBOOK
PHONEBOOK [39]www.uniden.comSteps for Entering Names and Special CharactersRefer to the letters on the number keys to select the desired characters. With each press of a number key (0-9), the displayed character appears in the following order:Upper case letters first, lower case letters next and finally the number corresponding to the key.Number of times key is pressedPHONEBOOK
[40] PHONEBOOKwww.uniden.comIf you make a mistake while entering a nameUse */tone/< or #/> to move the cursor to the incorrect character.Press menu/del to erase the wrong character, and then enter the correct character.To delete all characters, press and hold menu/del.For example, to enter Movies:1) When the phone is in the standby mode, press phonebook. 2) Press select/, "Store/Edit Name" appears.3) Press 6 once, and then press #/> to move the cursor to the right.4) Press 6 six times.5) Press 8 six times.6) Press 4 six times.7) Press 3 five times.8) Press 7 eight times.9) When finished, press select/.To continue to store the telephone number, proceed to step 5 on page 37.If the next character uses the same number key, you must press #/> to move the cursor over. Otherwise the next time you press the number key, it changes the character that was previously set.notePHONEBOOK
PHONEBOOK [41]www.uniden.comViewing the PhonebookYour phone stores names/numbers in the phonebook memory locations, and you can search names in alphabetical order. You can view the phonebook even while the phone is in use.1) Press phonebook.If you recall the phonebook during a call, "Store [SELECT]" will not appear.2) Press ring/vol/∧ or ring/vol/∨, or the number keypad to scroll through the phonebook locations. Phonebook locations appear in alphabetical order (from first to last when you press ring/vol/∨, from last to first when you ring/vol/∧.Or, refer to the letters on the number keys to select the first letter of the desired name. Press a number key (2-9 and 0) once for the first letter, press twice for the second letter, and so on. The first location that begins with the letter you entered appears.For example, to search for "Movies", press 6 once. Press ring/vol/∧ or ring/vol/∨, until the phonebook location is displayed.3) To finish the viewing operation, press end (or phonebook during a call).During a call, don't press end or the call will be disconnected.notePHONEBOOK
[42] PHONEBOOKwww.uniden.comMaking Calls Using the PhonebookFrom Standby Mode1) When the phone is in the standby mode, view the phonebook location to dial (see "Viewing the Phonebook" on page 41).2) Press talk/flash or speaker. The displayed number is dialed.3) To hang up press end.From Talk Mode1) Press talk/flash or speaker.2) View the phonebook location to dial (see "Viewing the Phonebook" on page 41).3) Press select/. The number in the displayed phonebook location is dialed.4) To hang up press end.Speed DialingIf you store a phone number in a speed dial memory location (10 locations: SPD1 - SPD0), you can use the speed dialing feature. When the phone is in the standby mode, press and hold a number key (0-9) associated with the speed dial until the phone number appears, and then press talk/flash or speaker. The number stored in the speed dial (SPD1 - SPD0) is dialed.PHONEBOOK
PHONEBOOK [43]www.uniden.comEditing or Erasing a Stored Name, Phone Number, Distinctive Ring, and Speed Dial1) When the phone is in the standby mode, Press phonebook.2) Press ring/vol/∧ or ring/vol/∨, or the number keypad to view the phonebook locations (see "Viewing the Phonebook" on page 41).a. Editing the Stored Data1) When the phonebook location to be edited appears, press select/. "Store/Edit Name" appears. 2) Follow the steps 3 to 7 under "Storing Phone Numbers, Names, Distinctive Rings, and Speed Dial" on page 37 to complete the editing operation.3) Press select/. You will hear a confirmation tone.b. Deleting the Stored Data1) When the phonebook location to be deleted appears, press menu/del."Delete Memory?" appears.2) Press ring/vol/∧ or ring/vol/∨ to move the pointer to "Yes".3) Press menu/del. You hear a confirmation tone."Deleted!" appears in the display.PHONEBOOK
[44] PHONEBOOKwww.uniden.comChain DialingThe memory locations in the handset are not limited to phone numbers. You can also store a group of numbers (up to 20 digits), that you need to enter once your call connects. This is referred to as Chain Dialing.An example of this is a bank account number. Store the account or special number in one of the phonebook locations. (refer to "Storing Phone Numbers, Names, Distinctive Rings and Speed Dial" on page 37). When you call your bank, and you are prompted to enter the account number, scroll through your phonebook locations until you find your account or special number, then press select/.PHONEBOOK
CALLER ID [45]www.uniden.comCaller ID and CIDCW (Call ID on Call Waiting)You must subscribe to Caller ID services through your local telephone provider to use these features.When the telephone rings, the Caller ID feature allows you to view the callers name, phone number, date and time of call. With CIDCW (Caller ID on call waiting), you will hear a call waiting tone while you are on a call, and the Caller ID data is displayed. To accept the waiting call, press talk/flash (see page 27). Additionally, you can dial a number stored in the Caller ID list or save data to your Phonebook locations.Important:Memory locations for Caller ID messages and Phonebook locations (including Speed Dials) are common, you can store up to 100 in total. A Caller ID message is not stored when you have stored 100 of the phonebook locations. The earliest Caller ID message is overwritten when you have stored 100 of the phonebook locations and Caller ID messages in total.1) When the call is via a private branch exchange (PBX), the caller's phone number and name may not appear. 1) When the Caller ID message is received, the display shows the caller's phone number along with the date and time. The incoming call information is stored in the Caller ID record. If the Caller ID service includes the caller's name, the name will appear in the display (up to 15 characters).You may receive any one of the following messages:When invalid data is received "Incomplete Data"When a private name is received "Private Name"When a private number is received "Private Number"When a unknown name is received "Unknown Name"When a unknown number is received "Unknown Number"The date and time receivedCaller's nameCaller's phone numberIf you answer a call before the Caller ID message is received (for example, before the second ring), the Caller ID message will not appear.When the call is received via a telephone company that does not offer Caller ID service, the callers phone number and name d oe s n ot a pp ea r. (This includes some international calls.)noteCALLER ID
[46] CALLER IDwww.uniden.com2) When you pick up the phone, the display changes to Talk.(AutoTalk feature is set to on).Data errors appear as "❚."Viewing the Caller ID ListThe Caller ID list stores information for incoming calls - even unanswered calls.You can store 100 of the Caller ID messages and Phonebook locations (including SpeedDials) in total. You can view the Caller ID list during a call or when the phone is in the standby mode.1) Press call id. The summary screen appears. The screen shows the number of new messages and total messages.2) To view the Caller ID messages in historical order (from new to old or from old to new), repeatedly press ring/vol/∧ to scroll through the messages from the latest to the earliest, or ring/vol/∨ to scroll back through the messages.Or, to view the Caller ID messages with alphabetical search, press the number key pad (2-9 and 0) with the letter associated with the first letter of the desired message.Once you view the Caller ID list with alphabetical search, you cannot switch back to historical order (from new to old or from old to new) unless you exit and re-enter the operation.3) To finish the viewing operation, press call/id (or end during a call).The number of calls from the same Caller ID appears next to the received time. Once you view the new message, the number will be cleared and disappear.During a call, don't press end or the call will be disconnected.noteCALLER ID
CALLER ID [47]www.uniden.comDeleting a Caller ID MessageDeleting Information from the Caller ID List1) When the phone is in the standby mode, view the Caller ID information to be deleted (see "Viewing the Caller ID List" on page 46).2) Press menu/del. "Delete Caller ID" appears.3) Press ring/vol/∧ or ring/vol/∨ to choose "Yes."4) Press select/. You will hear a confirmation tone.Deleting all Caller ID names/numbers1) When the phone is in the standby mode, press call id."Caller ID", and then press the OK soft key.The number of new and total records appears.2) Press ring/vol/∧ or ring/vol/∨ to choose "Yes."3) Press select/. You will hear a confirmation tone.Once the Caller ID data has been deleted, the information cannot be retrieved.Standby Mode - The handset is not in use, The handset may be on or off the base, but talk/flash key h a s been pressed.Talk Mode - The handset is not in the cradle and talk/flash or speaker has been pressed enabling a dial tone. "Talk" appears on the display.noteCALLER ID
[48] CALLER IDwww.uniden.comUsing the Caller ID Message ListCalling a party from the Caller ID listFrom Standby mode1) When the phone is in the standby mode, view the Caller ID message (see "Viewing the Caller ID List" on page 46).2) Press talk/flash or speaker. The displayed phone number dials automatically.From Talk mode1) Press talk/flash or speaker.2) View the Caller ID message you want to dial (see "Viewing the Caller ID List" on page 46).3) Press select/. The displayed phone number will be dialed.Long Distance calls and Area Code Setting/CancellationWhile the present Caller ID information is displayed, pressing */tone/< will place or remove the prefix "1" in the display to set the call for a long distance call, or pressing #/> will set or cancel an area code (see page 28).Storing Caller ID messages in the PhonebookMessages shown in the Caller ID list can be stored in the phonebook. The phone number and name of the party on the Caller ID list can be stored in memory.1) When the phone is in the standby mode, view the Caller ID message to be stored.Then press select/. "Store/Edit Name" appears.2) To complete the setting, follow the steps 4-8 in "Storing Phone Numbers, Names, Distinctive Rings, and Speed dial" on page 37.You cannot make a call from the Caller ID list if your phone is connected to a private branch exchange (PBX).When a long distance call has been set, "1" appears in the display.If a call comes in via a telephone system that does not offer Caller ID service, no information is stored.If the Caller ID message was received as a private/unknown number, or the message does not have the number, you cannot store the message in the Phonebook. Or it was received as private/unknown name, the message will be stored as <No Name>.Even if the 100 memory locations are full, the message will be stored in the Phonebook. However, the message will be erased from the Caller ID list.noteCALLER ID
CALLER ID [49]www.uniden.comCall Waiting Deluxe FeaturesYour phone gives you new options for call waiting. At the touch of a button, you can place the caller on hold, send them to your voice mail service, or conference them into your current call. You may be required to subscribe to Call Waiting and Call Waiting Deluxe to use these features. Not all features are available in all areas. Check with your local telephone company for details.1) When you receive a Call Waiting call, press menu/del for a list of options.2) Press ring/vol/∧ or ring/vol/∨ to select CW deluxe, and then press select/.3) Press ring/vol/∧ or ring/vol/∨ or the number keypad (1-7) to select an option.For example:press ring/vol/∨ 4 times press ring/vol/∨ 2 times3) Press select/. A confirmation screen will appear, and returns back to the call.Your phone is pre-programmed with seven call waiting options. You may select to ask the calling party to hold, send them a busy message, forward them to your voice mail, or answer and drop the first caller. You may also select to conference them into the current call or, at any time, choose to drop the first or drop the last caller. Check with your local telephone company for a full list of options.To activate features, select "CW On/CWDX On" in the CIDCW option. See page 27.You can also answer a waiting call immediately by pressing talk/flash, the first caller will be placed on hold. To return to the original caller, press talk/flash again.If you don't press a key within 30 seconds while in the operation, the phone back to a call.noteCALLER ID
[50] THE INTEGRATED ANSWERING DEVICEwww.uniden.comThe Integrated Answering DeviceThe phone has a built-in answering system that answers and records incoming calls. You can also use your answering system to record a conversation, leave a voice memo message, or to announce a special outgoing message to callers when you're away from your phone.Features Digital Tapeless Recording Approx. 12 Minutes of Recording Time Call Screening On/Off Selectable Outgoing Messages Voice Prompts for Menu Setup Guidance Time and Day Announcement Remote Message Retrieval Toll Saver Conversation Recording Voice Memo Trilingual Language OptionMessage Alert Remote Operation from the HandsetDigital Tapeless Recording allows you to quickly review, save, or delete the messages you choose. You will never have to worry about a tape wearing out, jamming, or resetting improperly.The Integrated Answering System is easy and convenient to use, but please read through all of the instructions carefully.THE INTEGRATED ANSWERING DEVICE
THE INTEGRATED ANSWERING DEVICE [51]www.uniden.comTurning the Answering System On/Off1) To turn the answering system On, press answer on/off in the standby mode.After the announcement "Answering System is on", the current greeting message will be played and you will hear a confirmation tone. The message counter displays the number of messages stored in memory. If the display flashes, then there are new messages waiting for you.2) To turn the answering system Off, press answer on/off. After the announcement "Answering System is off", the message counter display will no longer be illuminated.You can also turn the Answering System On or Off from the handset using the menu mode (see page 20).Setting up your Answering SystemSetting your outgoing message (Greeting)When you receive a call, the answering system automatically plays either the pre-recorded message or your own greeting.Pre-recorded messageThe following message is pre-recorded:"Hello, no one is available to take your call. Please leave a message after the tone."Recording a personal outgoing message (Greeting)You can record a greeting up to 30 seconds long (must be more than 2 seconds long).1) When the phone is in the standby mode, press and hold greeting.2) Start your recording after the announcement "Record greeting".The message counter displays " - -", then begins to count down.3) When you have finished recording your greeting, press greeting, or set.You will hear a confirmation tone and your recorded greeting plays back for you.When the answering system is full, "FL" appears on the base. You should delete some messages so that the system can record new messages.Position yourself as near to the base as possible and speak clearly when recording your outgoing message.If you make an outside call, or a call is received on the base during the operation, the operation is canceled.noteTHE INTEGRATED ANSWERING DEVICE
[52] THE INTEGRATED ANSWERING DEVICEwww.uniden.comChoosing between the two outgoing messagesWhen the phone is in the standby mode, press greeting. Press greeting again when the outgoing message is played. Each time greeting is pressed, the outgoing message is switched between the pre-recorded and the personal outgoing message.Deleting an outgoing messageTo delete the personal outgoing message, press delete while the message is playing. The system announces "Greeting has been deleted".Setting the base ringer volumeYou have four ringer volume options. One allows you to turn the base ringer off.The other three are volume levels.1) When the phone is in the standby mode, press ring/vol/∧ or ring/vol/∨. You hear the ringer at the current volume level ("3" High, "2" Medium, "1" Low, or "0" Off) (if you set the base ringer volume to off "Ringer Off" is announced), and it appears on the base.2) Press ring/vol/∧ or ring/vol/∨ repeatedly until the desired ringer volume appears. You will hear a ringer at the selected volume level. The system returns to the standby mode.You can also set the base ringer volume or while the phone is ringing, press ring/vol/∧ or ring/vol/∨ repeatedly to select the desired ringer volume.Adjusting the speaker volume levelWhen the base speaker is in use, press ring/vol/∧ or ring/vol/∨ on the base to adjust the volume. Press ring/vol/∧ for louder or ring/vol/∨ for softern.The number 1-10 appears on the base indicating the volume levels. 1 being the softest and 10 being the loudest.THE INTEGRATED ANSWERING DEVICE
THE INTEGRATED ANSWERING DEVICE [53]www.uniden.comUsing the menu modeThe Menu mode allows you to set the following Answering System functions. To scroll through the menu options, repeatedly press clock/MENU on the base in the standby mode.The system returns to standby after the last menu option. A confirmation tone sounds to indicate the standby mode. When you have completed the setting, press play/stop to exit the menu mode, or clock/MENU to move to the next menu option. You can also set these menus from the handset. See "Answering System Setup" on page 25 for instructions.For your convenience, voice prompts will guide you through the menu setup mode.Clock/MENUClock/MENUClock/MENUClock/MENUClock/MENUClock/MENUClock/MENUClock/MENU"Time""Security Code""Ring Time""Record Time""Message Alert""Language""Call Screening"Return to StandbyTHE INTEGRATED ANSWERING DEVICE
[54] THE INTEGRATED ANSWERING DEVICEwww.uniden.comSetting the TimeFollow these steps to set the clock on the answering system to the correct time.1) Press clock/MENU.2) Press skip/SELECT or repeat/SELECT until the correct day is announced and the corresponding number (from "1" Sunday to "7" Saturday) appears.3) Press SET to select the day.4) Press skip/SELECT or repeat/SELECT until you hear the correct hour setting.The numbers "1" through "12" appear on the base as each hour is announced.5) Press SET to select the hour.6) Press skip/SELECT or repeat/SELECT until you hear the correct minute setting.The numbers "00" through "59 appears on the base as each minute is announced.7) Press SET to select the minute.8) Press skip/SELECT or repeat/SELECT until you hear the correct AM or PM setting.The message counter displays "A" or "P".9) Press SET to select the AM/PM setting.A confirmation tone sounds, the day and time you set are announced for your review.Setting a PIN codeTo play your messages from a remote location, you will need to enter a two-digit Personal Identification Number (PIN) code ( - - ). To select a PIN code, perform the following steps:1) Press clock/MENU twice. The current PIN code appears on the base and it is announced.2) Press skip/SELECT or repeat/SELECT until the desired number appears. Press and hold skip/SELECT or repeat/SELECT to quickly scroll through the numbers on the display.3) Press SET to select the PIN code.A confirmation tone sounds, the system announces the new PIN code.Time stamp will not be heard until you have set the time.noteTHE INTEGRATED ANSWERING DEVICE
THE INTEGRATED ANSWERING DEVICE [55]www.uniden.comSetting the ring timeThe ring time setting allows you to set the number of rings the caller hears before your answering system plays the outgoing message. You can set the ring time to answer after two, four, or six rings. Setting "TS" (Toll Saver), the answering system picks up after two rings if you have new messages, and after four rings if there are none. This way, if you make a long distance call to check your messages, you can hang up after the second ring to avoid billing charges.1) Press clock/MENU three times.The current ring time setting ("2" 2, "4" 4, "6" 6, "tS" Toll saver) appears on the base and it is announced.2) Press skip/SELECT or repeat/SELECT until the desired ring time appears.3) Press SET to select the new ring time.A confirmation tone sounds, the system announces the new ring time.Selecting the message record timeYou have three record time options. The options "1 minute" or "4 minutes" set the duration for recording the incoming messages. "Announce only" answers the call with the preset greeting or your personal greeting but prevents the caller from leaving a message.1) Press clock/MENU four times.The current recording time ("1" 1 minute, "4" 4 minutes, "A" Announce only) appears on the base and it is announced.2) Press skip/SELECT or repeat/SELECT until the desired message record time appears.3) Press SET to select the new recording time.A confirmation tone sounds, the system announces the new record time.THE INTEGRATED ANSWERING DEVICE
[56] THE INTEGRATED ANSWERING DEVICEwww.uniden.comAnnounce only featureThe Announce only feature plays a pre-recorded outgoing message or your own personal outgoing message, but it will not allow the caller to leave a message. To set "Announce only", follow the steps on page xx. To choose between the pre-recorded message or your own personal greeting, press greeting, when the outgoing message is played. Press greeting to select the greeting of your choice.If you want to use your own greeting, you may want to change your greeting to omit the prompt to leave a message. Refer to "Recording a Personal outgoing message (Greeting)" on page 51.The following message is pre-recorded:"Hello, no one is available to take your call. Please call again."Setting the message alertMessage Alert feature lets you know when you have a new incoming message by sounding a short alert tone.If you set the Message Alert On, and when a new message is received, the alert tone will sound every 15 seconds. Set the Message Alert to On or Off by using the clock/MENU key.1) Press clock/MENU five times. The current setting (On or Off) appears on the base and it is announced.2) Press skip/SELECT or repeat/SELECT to choose "On" or "Off".3) Press SET.A confirmation tone sounds, the system announces the current setting you have selected. When the first new message is received, the alert tone will begin to sound.THE INTEGRATED ANSWERING DEVICE
THE INTEGRATED ANSWERING DEVICE [57]www.uniden.comTurning the message alert tone Off by pressing any keyTo quickly turn Message Alert tone to Off, press any key on the base unit and the tone will automatically deactivate.Turning the message alert tone Off when you are away from your phoneWhen all new messages are played back using the remote playback feature (see pages xx-xx) the Message Alert tone will automatically deactivate. The tone will not deactivate until all new messages are played back.Selecting the languageYou can select the Language of your answering system announcements to English, French, or Spanish.1) Press clock/MENU six times.The current setting ("E" English, "F" French, or "S" Spanish) appears on the base, and it is announced ("English" English, "Français" French, or "Español" Spanish).2) Press skip/SELECT or repeat/SELECT to select the language.3) Press SET.A confirmation tone sounds, the system announces the new setting in the selected language.Setting the call screenYou can screen calls when the Call Screen function is set to On.1) Press clock/MENU seven times.The current Call Screen setting (On or Off) appears on the base.2) Press skip/SELECT or repeat/SELECT to choose "On" or "Off".3) Press SET. A confirmation tone sounds, and the system announces the new setting.If you mute the ringer for an incoming call, you can not screen the call.If you press talk/flash, call screen will be canceled and the handset is put in talk mode.If you press select/ while another handset is screening a call, you will hear a beep and you can not screen a call.noteTHE INTEGRATED ANSWERING DEVICE
[58] THE INTEGRATED ANSWERING DEVICEwww.uniden.comScreening a callFrom the baseTo screen an incomming call, do the steps as follows:1) After the answering system answers, the base speaker will let you hear the calls as the machine records the message. To adjust the volume, press ring/vol/∧ or ring/vol/∨. If you set the answering system to Off, you cannot screen a call.2) To answer the call, press speaker (talk) or pick up the handset from the base (when AutoTalk is set to On). If the handset is away from the base, press talk/flash, speaker or any number key, */tone/<, or #/> (when AutoTalk is set to On). The answering system will disconnect automatically.From the handsetPress select/ when the system is answering. To answer the call, press talk/flash, otherwise press end to cancel the call screen and the system return to the standby mode.Muting the Call ScreenYou can mute the Call Screen. To do this, press DND on the base. To cancel the Call Screen, press ring/vol/∧ or ring/vol/∨ on the base. To mute the Call Screen again, press play/stop. The Call Screen function resumes when the system is no longer in answering mode.THE INTEGRATED ANSWERING DEVICE
THE INTEGRATED ANSWERING DEVICE [59]www.uniden.comUsing your Answering SystemThe message counter displays the number of messages stored in memory. If the display flashes, then there are new messages waiting for you. The answering system is designed to play your new messages first. After you play all your new messages, you can then play your old messages.Playing your messages1) When the phone is in the standby mode, press play/stop.The system announces the number of new and old messages while the message counter displays only the number of new messages. The time and day that each message was received is announced after the message is played. The message counter will then display the number of current stored messages.2) When all new messages have been played, you hear a confirmation tone and the system announces "End of message". The system returns to standby. After you have reviewed your new messages, you can play your old messages by again pressing. Once you have listened to a new message, it then becomes an old message. The old messages will be played in the order in which they were received.Repeating a message1) Press play/stop to review your messages. The number of stored messages is announced.2) To repeat the current message, press repeat/SELECT after a few seconds of beginning the message. To quickly scroll backwards through a message, press and hold repeat/SELECT.To repeat the previous message, press repeat/SELECT within a few seconds (about 4 seconds during remote operation) after a message begins playing. If you have several messages, press repeat/SELECT repeatedly until you return to the message you want to replay. If the current message is the first new message, the system plays back from the beginning of the current message (it does not go back into the old message group).3) Press play/stop at any time to stop reviewing messages and return to standby.The message counter shows the number of messages stored in memory.Time stamp will not be heard until you have set the time.When the answering system is full, "FL" appears on the base. You should delete some messages so that the system can record new messages. (Refer to "Deleting a message" on page 60.)noteTHE INTEGRATED ANSWERING DEVICE
[60] THE INTEGRATED ANSWERING DEVICEwww.uniden.comSkipping a message1) Press to review your messages. The number of stored messages is announced.2) Press skip/SELECT at anytime to skip to the next message.Each time skip/SELECT is pressed, the system scans forward one message. If you have several messages, press skip/SELECT repeatedly to find the message you want to play. To quickly scroll through a message, press and hold skip/SELECT. The system advances through the playback at double speed.3) Press play/stop at anytime to stop reviewing your messages and return to standby.The message counter shows the number of messages stored in memory.Deleting a messageTo maintain maximum record time, delete the old messages.1) Press to review your messages.2) Press delete at anytime during the message to delete the message. You hear a confirmation tone and the message is deleted.3) To delete all messages, press delete in the standby mode. Press delete again after the announcement "To delete all message, press delete again."When you try to delete all messages without first listening to your new messages, you hear several short beeps followed by an announcement "Please playback all messages".This protects you from accidentally erasing messages you have not yet reviewed.Important:When you press del, you are permanently deleting the message. Once deleted, the message cannot be replayed or retrieved.THE INTEGRATED ANSWERING DEVICE
THE INTEGRATED ANSWERING DEVICE [61]www.uniden.comVoice memoThe voice memo function allows the user to record messages (more than 2 seconds and within 4 minutes).1) Press and hold memo record. You hear a beep.2) Start your recording after the announcement "Record Memo Message" and a confirmation tone. The message counter displays "- -".3) When you have finished, press memo reccord, play/stop, or set to stop recording. The system returns to standby.Recording a conversationYou can record a conversation from the handset or the base (more than 2 seconds and within 10 minutes).From the handset1) During a conversation, press menu/del on the handset.2) Press ring/vol/∧ or ring/vol/∨ to select "Call Record", and then press select/voice mail key."Recording a Call" appears on the handset, and "- -" flashes on the base.A confirmation tone, that can be heard by both parties, sounds during recording.3) To stop recording, press menu/del and ring/vol/∧ or ring/vol/∨ to select "Call Record", and then press select/. You will hear a confirmation tone. From the base1) During a conversation using the base speaker phone, press and hold memo record on the base until you hear a confirmation tone. The unit begins recording and "- -" flashes on the display. A confirmation tone, that can be heard by both parties, sounds during recording.2) To stop recording, press play/stop or memo record. You hear a confirmation tone.The voice memo messages are recorded as an incoming messages.When the answering system is full, "FL" appears on the display and recording is terminated.If an outside call is received during the operation, the operation is canceled.Every state has different regulations governing the recording of conversations over the telephone. Make sure to check your local, state and federal laws before using this product to record any telephone conversation in order to determine that your use is in compliance with such laws or guidelines.You cannot record 3-way or intercom conversations.When the answering system becomes full, "FL" appears on the display and recording is terminated.noteTHE INTEGRATED ANSWERING DEVICE
[62] THE INTEGRATED ANSWERING DEVICEwww.uniden.comRemote OperationYou can check, play, or delete messages, even record a new greeting message from a remote location (when you are away from home, or from another room using a handset). Additionally, you can turn On or Off your answering system remotely.Remote access away from homeYou can operate your answering system from a remote location using any touch-tone telephone .1) Call your telephone number and wait for the system to answer. If the answering system is off, it will answer after about 10 rings and sounds a series of beeps.2) During the greeting message (or a series of beeps when the answering system is off), press 0 and enter your PIN code within 2 seconds (see "Setting a PIN Code" on page 25 or 54).3) The answering system announces the current time and the number of messages stored in memory. You hear "To play incoming messages, press zero-two. For help, press one-zero". You will hear a beep.4) Enter a command within 15 seconds, each command there after must be entered within 2 seconds. You may select a command from the following chart: Command Function Command Function0 then 1Repeat a Message* 0 then 6Answering System On0 then 2Playing incoming Messages 0 then 7Memo Record/Stop**0 then 3Skipping a Message 0 then 8Greeting Message Record/Stop**0 then 4Deleting a Message 0 then 9Answer System Off0 then 5Stop Operation 1 then 0Help GuidanceTime stamp will not be heard until you have set the time. See "Setting the Time" on page 54.The system will only playback messages for four minutes and then it returns to the command waiting mode. To continue playing your messages, press 0 then 2 again within 15 seconds.f you enter an incorrect PIN code three times, you will hear a beep and the system will return to standby.During the remote operation, "Lr" appears on the base.If the answering system is recording an incoming message, the recording operation is canceled when you start remote operation.For your convenience a remote operation card is provided for you to use while away from home (refer to page 82).noteTHE INTEGRATED ANSWERING DEVICE
THE INTEGRATED ANSWERING DEVICE [63]www.uniden.com* For Repeat a Message function, press 0 then 1 within about four seconds to repeat the previous message, or press 0 then 1 after about four seconds to repeat the current message.** For Memo Record and Greeting Message Record function, the first time you enter the corresponding command, it starts the Recording function. If you want to stop the recording, press 0 then 7 or 8.5) After the command has finished, you hear intermittent beeps indicating that the system is in the command waiting mode. You may enter another command at this time from the chart above.6) When you are finished, hang up to exit the system. The answering system automatically returns to standby.Remote access with the handsetYou can operate your answering system from another room using a handset.If you press end before the answering system answers, the phone will return to standby. When the answering system does not answer within 6 seconds, you hear a beep and the phone will return to standby. The base's keypad is disabled during remote operation. When you receive a call, the remote operation is canceled. You can change the handset volume during a remote operation. During the remote operation "Lr" appears on the base. If you have new messages and old messages, only the new messages will be played. After you have reviewed your new messages, you can play your old messages by again pressing 2.1) When the phone is in the standby mode, press select/voice mail on the handset. "Remote Answering Machine Operation" appears on the handset display. The answering system announces the current time and the number of messages stored in the memory.THE INTEGRATED ANSWERING DEVICE
[64] THE INTEGRATED ANSWERING DEVICEwww.uniden.comMessages will be played in the order in which they were received. The time and day that each message was received is announced after the message is played. To switch to the handset speaker phone, press speaker on the handset. 2) The answering system announces the current time and the number of messages stored in memory. You hear "To play incoming messages, press two. For help, press zero".You will hear a beep.3) Enter a command within 15 seconds, each command there after must be entered within 2 seconds. You may select a command from the following chart:Remote Key Function* For Repeat a Message function, press 1 within about four seconds to repeat the previous message, or press 1 after about four seconds to repeat the current message.** For Memo Record and Greeting Message Record function, the first time you enter the corresponding command, it starts the Recording function. If you want to stop the recording, press 7 or 8.5) After the command has finished, you hear intermittent beeps indicating that the system is in the command waiting mode. You may enter another command at this time from the chart above.6) When you are finished, hang up or press end to exit the system. The answering system automatically returns to standby.|<</1 Repeat a Message* 6Answering System On/2 Playing incoming Messages 7Memo Record/Stop**>>|/3 Skipping a Message 8Greeting Message Record/Stop**∅/4 Deleting a Message 9Answer System Off/5 Stop Operation 0Help GuidanceTHE INTEGRATED ANSWERING DEVICE
EXPANDING YOUR PHONE [65]www.uniden.comExpanding Your Phone4 Multi-Handset ExpandabilityYour phone supports up to 4 handsets (including the handset(s) supplied with your phone). You can now place a fully featured cordless handset anywhere AC power is available to connect the handset charger.Up to 2 handsets can be used for an outside and/or intercom call.For example, the phone permits 3-way conferencing (2 handsets and an outside line).IMPORTANT: If you purchase a DCX640 extra handset, please register the handset to the original base before use. The DCX640 will not operate until it is registered. If you change a Global setting in one handset, you change that particular setting for all registered handsets. All other settings (not included under Global Setup), must be set separately through each handset.Connecting the Charger1) Connect the AC adapter to the DC IN 9V jack and to a standard 120V AC wall outlet.2) Set the charger on a desk or tabletop, and place the handset in the charger with the keypad facing forward.(See "B. Install the battery pack into the handset" on page 10).Multi_HandsetCharger_AC_cordTo use the DCX640, register it to the original base.Save this manual for detailed operation.All of the handsets ring when a call is received.noteEXPANDING YOUR PHONE
[66] EXPANDING YOUR PHONEwww.uniden.comRegister the HandsetIf you purchase an extra handset, you need to register the handset before use. Only one handset can be registered at a time. The handset ID for the supplied handset(s) was assigned at the factory, which has #1 (#1 and #2 for 2 handsets bundled model) in the display. When you register additional handsetto the base, the handset ID will be assigned.1) Before registering the extra handset, charge the phone's battery for 10 minutes.2) Place the extra handset in the main base unit to begin registration.3) While the handset is registering, "Handset Registering" will appear in the LCD.When "Registration Complete" is displayed, the handset has been registered to the base. If "Registration Failed" appears, please try these steps again.4) Place the handset back in the charging cradle and fully charge the phone's battery.An extra handset can be registered when the main base is in the standby mode.Standby Mode - The handset is not in use, The handset may be on or off the base, but talk/flash key h a s been pressed.note
EXPANDING YOUR PHONE [67]www.uniden.comUsing the DirectLink ModeTo use this feature, you must enter the two handsets into the DirectLink mode first.To enter the DirectLink mode, see page 22DirectLink call1) When the phone is in the DirectLink standby mode, press talk/flash (example of DirectLink from handset #1).2) Select the handset to which you wish to DirectLink with by pressing the number keys (1-4). Your handset will then page the other handset.3) On the receiving handset, press talk/flash, or if Any Key Answer is On, press any number key, */tone/<, or #/>.4) When you finish your conversation, press end on either handset. Return the handset to the cradle, or press menu/del, and then select/ to return to normal standby mode (canceling DirectLink mode).3waycallTwo handsets can be in Direct Link mode while other handsets are in use.noteEXPANDING YOUR PHONE
[68] EXPANDING YOUR PHONEwww.uniden.com4-Way ConferencingFourth person, at either the handset or the base, may be added to the conference call. For example, to add a fourth party to an ongoing conference call at the base or another handset, press talk/flash on the fourth party's handset (or speaker on the base). To remove either caller from your conversation, press end on the party's handset (or speaker on the base). The other parties will still be connected to the callIntercom/Call Transfer FeatureIntercom and Call Transfer features are available for your phone.IntercomFrom handset to handset or to the base1) Press hold/transfer/int'com in the standby mode.2) Select the base or the handset you want to talk with from the selection list within 30 seconds. To select the handset (or the base), press ring/vol/∧ or ring/vol/∨, and then press select/. If you select "All", all handsets and the base will be paged. An intercom tone sounds.3) On the receiving handset (or the base), to answer the call, press talk/flash, hold/transfer/int'com (or intercom/find handset or speaker on the base). Or press any number key,*/tone/<, or #/> (when Any Key Answer is On), or pick up the handset from the cradle (when AutoTalk is On).4) To hang up the intercom call, press end on either handset (or intercom on the base). If the party is busy or out of range, the handset returns to the standby mode.If any of the following occurs while selecting the other handset, the operation will be canceled.- Press talk/flash or speaker.-Receive an outside/intercom call or page.When the party does not answer within one minute, the operation is canceled.Standby Mode - The handset is not in use, The handset may be on or off the base, but talk/flash key h a s been pressed.note
EXPANDING YOUR PHONE [69]www.uniden.comFrom the base to a handset1) Press intercom/find handset on the base in the standby mode.2) All the handsets will be paged.3) On the receiving handset, to answer the call, press talk/flash or hold/transfer/int'com. Or press any number key, */tone/<, or #/> (when Any Key Answer is On), or pick up the handset from the cradle (when AutoTalk is On).4) To hang up the intercom call, press end on intercom/find handset on the base.Call Transfer FeatureFrom handset to handset or to the base1) During a call, press hold/transfer/int'com on the handset.2) Select a handset or the base to transfer the call within 10 seconds. (Refer to step 2 in the intercom section on page 68).The call will automatically be placed on hold, and an intercom tone sounds.To cancel the transfer, press talk/flash or speaker on the initiating handset.3) On the receiving handset, to answer the page, press talk/flash or hold/transfer/int'com (or speaker or intercom/find handset on the base). Or press any number key, */tone/<, or #/> (when Any Key Answer is On), or pick up the handset from the cradle (When Auto Talk is On).4) To speak to the caller, press talk/flash or speaker (or speaker on the base) on the receiving handset.EXPANDING YOUR PHONE
[70] EXPANDING YOUR PHONEwww.uniden.comFrom the base to a handset1) During a call, press intercom/find handset on the base. The call will automatically be placed on hold, and an intercom tone sounds. All the handset(s) will be paged.2) On the receiving handset, to answer the call, press talk/flash or hold/transfer/int'com. The intercom mode is activated, but the caller is still on hold. Or press any number key, */tone/<, or #/> (when Any Key Answer is On), or pick up the handset from the cradle (when AutoTalk is On).3) To speak to the caller, press talk/flash or speaker on the receiving handset.Replacing the BaseWhen you replace the base with a different base of the DCT6 series model (DCT646,DCT6465, DCT648, or DCT6485 series), you need to clear the handset(s) and base ID. To do this, perform the "System Reset" menu options ("De-register the Handset" and "Replacing the Base Setting") (see page 29), then register all the handsets you have (see page 66).For model number verification, contact Uniden Customer Service or visit our website www.uniden.comnote
ADDITIONAL INFORMATION [71]www.uniden.comChanging the Digital Security CodeThe digital security code is an identification code used to connect the handset and the base unit. Normally, setting the code is not necessary. In the rare situation that you suspect another cordless telephone is using the same security code, you can change the code. To change the digital security code:1. Perform the "System Reset" menu options ("De-register the Handset" and "Replacing the Base Setting") for all the handsets you have (see page 29).2. To register all the handsets do the following steps:1) Place a handset, one at a time in the base.2) Registration starts automatically.While registering "Handset Registering" appears in the display.3) When the registration is complete, "Registration Complete" appears in the display.4) Repeat steps 1 - 3 for another handsets.If the registration fails, "Registration Failed" appears in the display. Try the stepsabove again.Installing the BeltclipTo attach the beltclipInsert the beltclip into the holes on each side of the handset.Press down until it clicks.To remove the beltclipPull both sides of the beltclip to release the tabs from the holes.Headset InstallationYour phone may be used with an optional headset, the Uniden HS910. To use this feature, insert the headset plug into the headset jack. Your phone is ready for hands-free conversations (headset may be purchased by calling the Uniden Parts Department or visiting the web site. See page 1).beltclipheadset_jackADDITIONAL INFORMATION
[72] ADDITIONAL INFORMATIONwww.uniden.comNote on Power SourcesBattery replacement and handlingWhen the operating time becomes short, even after a battery is recharged, please replace the battery. With normal usage, your battery should last about one year. Please contact your place of purchase or the Uniden Parts Department for a replacement battery. WarningTo avoid the risk of personal injury or property damage from fire or electrical shock, only use the Uniden battery model and Uniden adapter model specifically designated for this product.Power FailureDuring the period that the power is off, you will not be able to make or receive calls with the telephone.Caution Use only the specified Uniden battery pack (BT-446). Do not remove the batteries from the handset to charge them. Never throw the battery into a fire, disassemble them, or heat them. Do not remove or damage the battery casing.MaintenanceTo maintain a good charge, it is important to clean the charging contacts on both the handset and the base unit once a month. Using water only, dampen a cloth to clean the charging contacts. Then make sure to go back over the charging contacts with a dry cloth.CautionDo not use paint thinner, benzene, alcohol, or other chemical products. Doing so may discolor the surface of the telephone and damage the finish.ADDITIONAL INFORMATION
ADDITIONAL INFORMATION [73]www.uniden.comGeneral InformationThe phone complies with FCC Parts 15 and 68. Operating temperature: 0 °C to +50 °C (+32 °F to +122 °F)AC Adapter InformationAC Adapter part number: AD-xxx for the base AD-xxx for the charger(2 handsets included model only)Input Voltage: 120 AC 60Hz 120V AC 60HzOutput Voltage: 9V DC xxxmA 9V DC xxxmABattery InformationBattery part number: BT-446Capacity: xxxxmAh, xxxVTo avoid damage to the phone use only Uniden AD-xxx and BT-446 with your phone.If the handset is left off of the base, the actual Talk mode duration will be reduced respective to the amount of time the handset is off the base.Recharge your phone on a regular basis by returning the handset to the base after each phone call. When the operating time becomes short, even after the battery is recharged, please replace the battery. With normal usage, the battery should last about one year.A replacement Uniden adapter or battery may be purchased by contacting the Uniden Parts Department (800) 554-3988. Hours are from 8:00 a.m. to 5:00 p.m. Central Time, Monday through Friday. We can also be reached on the web at www.uniden.com.Specifications, features, and availability of optional accessories are all subject to change without prior notice.ADDITIONAL INFORMATION
[74] TROUBLESHOOTINGwww.uniden.comTroubleshootingIf your phone is not performing to your expectations, please try these simple steps first.Symptom SuggestionThe charge/in use (or charge) LED won't illuminate when the handset is placed in the cradle. Make sure the AC adapter is plugged into the base (or the charger (for DCX640 only)). and wall outlet. Make sure the handset is properly seated in the cradle. Make sure the charging contacts on the handset and the base (or the charger (for DCX640 only)) are clean.The audio sounds weak. Move the handset and/or base to a different location away from and/or scratchy metal objects or appliances and try again. Make sure that you are not too far from the base.Can't make or receive calls. Check both ends of the base telephone line cord. Make sure the AC adapter is plugged into the base and wall outlet. Disconnect the AC adapter for a few minutes, and then reconnect it. Remove the base ID (see "Replacing the Base Setting" on page 29) and register the handset (see "Register the Handset" on page 66). Make sure that you are not too far from the base. If an outside call is already established, you may not be able to make another outside call.The handset doesn't ring or receive a page. Charge the batteries in the handset for 17-20 hours by placing the handset on the base or charging cradle. The handset may be too far away from the base unit. Place the base unit away from appliances or metal objects. Remove the base ID (see "Replacing the Base Setting" on page 29) and register the handset (see "Register the Handset" on page 66)."Unavailable" appears in the display. Make sure that another handset(s) or the base is not in use, and try the phone again. Make sure that you are not too far from the base.TROUBLESHOOTING
TROUBLESHOOTING [75]www.uniden.comSevere noise interference. Keep the handset away from microwave ovens, computers, remote control toys, wireless microphones, alarm systems, intercoms, room monitors, fluorescent lights, and electrical appliances. Move to another location or turn off the source of interference.The Caller ID does not display. The handset was picked up before the second ring. The call was placed through a switchboard. Call your local telephone company to verify your Caller ID service is current.You cannot register the handset at the base. Please make sure your batteries are charged at least 10 minutes (see "Register the Handset" on page 66). Remove the base ID (see "Replacing the Base Setting" on page 29) and register the handset (see "Register the Handset" on page 50).The handset doesn't communicate with the other handsets. Remove the base ID (see "Replacing the Base Setting" on page 29) and register the handset (see "Register the Handset" on page 66). Make sure that you have registered all handsets.An extra handset can't join the conversation.  Make sure there are not 2 handsets already using the 3-way conference feature.The handset or the base can't join the conversation Make sure that more than 3 handsets (or 2 handsets when the base is used for the conference) are not in use. When recording a conversation, the 2nd handset (or the base) cannot join the conversation.The answering system does not work. Make sure the base unit is plugged in. Make sure that the answering system is turned On. Make sure that the message record time is not set to Announce only (see page 56).Messages are incomplete.  The incoming messages may be too long. Remind callers to leave a brief message. The memory may be full. Delete some or all of the saved messages.After a power failure, the outgoing message is deleted.  Record your greeting again. The default message should remain.Symptom SuggestionTROUBLESHOOTING
[76] TROUBLESHOOTINGwww.uniden.comNo sound on the base unit speaker during call monitoring or message playback. Adjust the speaker volume on the base unit. Make sure the call screen feature is set to On.Cannot access remote call-in features from another touch-tone phone. Make sure you are using the correct PIN number. Make sure that the touch-tone phone you're using can transmit the tone for at least two seconds. If it cannot, you may have to use another phone to access your phone.Time stamp cannot be heard.  Make sure you have set the time (see "Setting Day and Time" on page 27 or "Setting the Time" on page 54).If you still have a problem.  Call our customer hotline at 1-800-297-1023.Symptom SuggestionTROUBLESHOOTING
TROUBLESHOOTING [77]www.uniden.comLiquid DamageMoisture and liquid can damage your cordless phone. In case of accidental submersion, please read the following steps.Case ActionIf the handset or base is exposed to moisture or liquid, but the liquid only affects the exterior plastic housing.Wipe off the liquid, and use as normal.If moisture or liquid has entered the plastic-housing (i.e. liquid can be heard in the phone or liquid has entered the handset battery compartment or vent openings on the base).Handset:1)Remove the battery cover and leave it off for ventilation.2)Remove the battery pack by disconnecting.3)Leave the battery cover off and the battery pack disconnected for at least 3 days.4)Once the phone is completely dry, reconnect the battery pack and the battery cover.5)Recharge the handset's battery pack for 20 hours in the base unit before using the phone.Base:1)Disconnect the AC adapter from the base unit, cutting off electrical power.2)Disconnect the telephone cord from the base unit.3)Let dry for at least 3 days.IMPORTANT: You must unplug the telephone line while recharging the batteries to avoid charge interruption.CAUTION:DO NOT use a microwave oven to speed up the drying process. This will cause permanent damage to the handset, base and the microwave oven.After following these steps, if your cordless telephone does not work, please send to:Uniden America CorporationParts and Service Division4700 Amon Carter Blvd.Ft. Worth TX 761551-800-554-3988. Monday through Friday8 a.m. to 5 p.m. CSTTROUBLESHOOTING
[78] PRECAUTIONS & WARRANTYwww.uniden.comPRECAUTIONS & WARRANTYPrecautions!Before you read anything else, please observe the following:Warning!Uniden America Corporation DOES NOT represent this unit to be waterproof. To reduce the risk of fire, electrical shock, or damage to the unit, DO NOT expose this unit to rain or moisture.Rechargeable Nickel-Metal-Hydride Battery Warning This equipment contains a rechargeable Nickel-Metal-Hydride battery. Nickel is a chemical known to state of California to cause cancer. The rechargeable Nickel-Metal-Hydride battery contained in this equipment may explode if disposed of in a fire. Do not short-circuit the battery. Do not charge the rechargeable Nickel-Metal-Hydride battery used in this equipment in any charger other than the one designed to charge this battery as specified in the owner's manual. Using another charger may damage the battery or cause the battery to explode.Rechargeable Nickel-Metal-Hydride Batteries Must Be Recycled or Disposed of ProperlyThe exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance.Uniden works to reduce lead content in our PVC coated cords in our products and accessories.Warning!The cords on this product and/or accessories contain lead, a chemical known to the State of California to cause birth defects or other reproductive harm. Wash hands after handling.Important Safety InstructionsWhen using your telephone equipment, these basic safetyprecautions should always be followed to reduce the risk of fire, electrical shock, and injury to persons:1. Read and understand all instructions.2. Follow all warnings and instructions marked on the product.3. Unplug this product from the wall outlet before cleaning. Use a dry cloth for cleaning without liquid or aerosol cleaners.4. Do not use this product near water; for example, near a bathtub, wash bowl, kitchen sink or laundry tub, in a wet basement, or near a swimming pool.5. Do not place this product on an unstable cart, stand, or table.The telephone may fall, causing serious damage to the unit.6. Slots and openings in the cabinet and the back or bottom are provided for ventilation. To protect the product from overheating, these openings must not be blocked or covered.This product should never be placed near or over a radiator or heat register. This product should not be placed in a built-in installation unless proper ventilation is provided.7. This product should be operated only from the type of power source indicated on the marking label. If you are not sure of the type of power supply to your home, consult your dealer or local power company.8. Do not allow anything to rest on the power cord. Do not locate this product where the cord will be damaged by persons walking on it.9. Do not overload wall outlets and extension cords, as this can result in the risk of fire or electrical shock.10.Never push objects of any kind into this product through cabinet slots, as they may touch dangerous voltage points or short out parts that could result in a risk of fire or electric shock. Never spill liquid of any kind on the product.11. To reduce the risk of electric shock, do not disassemble this product. Take it to qualified service personnel when service or repair work is required. Opening or removing covers may expose you to dangerous voltages or other risks. Incorrect reassembly can cause electric shock when the appliance is subsequently used.12.Unplug this product from the wall outlet and refer servicing to qualified service personnel under the following conditions:A. When the power supply cord is damaged or frayed.B. If liquid has been spilled into the product.C. If the product has been exposed to rain or water.D. If the product does not operate normally when following the operating instructions. (Adjust only those controls that are covered by the operating instructions. Improper adjustment of other controls may result in damage and will often require extensive repair work by a qualified technician.)E. If the product has been dropped or the cabinet has been damaged.F. If the product exhibits a distinct change in performance.13. Do not use the telephone to report a gas leak i n th e vi cinity of the leak.Additional Battery Safety PrecautionsCaution! To reduce the risk of fire or injury to persons by the battery, read and follow these instructions:1. Use only the Uniden battery pack specified in the owner's manual.2. Do not dispose of the battery pack in a fire. The cell may explode. Check the Nickel Metal Hydride battery disposal package insert for disposal instructions.3. Do not open or mutilate the battery pack. Released electrolyte is corrosive and may cause damage to the eyes or skin. It may be toxic if swallowed.4. Exercise care in handling the battery in order not to short the battery with conducting materials such as rings, bracelets, and keys. The battery or conductor may overheat and cause burns.5. Charge the battery pack provided with or identified for use with this product only in accordance with the instructions and limitations specified in the owners manual provided for this product.6. Observe proper polarity orientation between the battery pack and battery charger.SAVE THESE INSTRUCTIONS!Important Electrical ConsiderationsUnplug all electrical appliances when you know an electrical storm is approaching. Lightning can pass through your household wiringand damage any device connected to it. This phone is no exception.The FCC Wants You To KnowChanges or modifications to this product not expressly approved by Uniden, or operation of this product in any way other than as detailed by the owner's manual, could void your authority to operate this product. Your telephone complies with Part 68 of FCC Rules. Youmust, upon request, provide the FCC registration number and the REN to your telephone company. Both numbers are on the base unit.Note: You must not connect your phone to: coin-operated systems most electronic key telephone systemsThis device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1) This device may not cause harmfulinterference, and (2) This device must accept any interference received, including interference that may cause undesired operation. Privacy of communications, may not be ensured when using this phone.RangeYour new phone is designed to achieve the maximum possible range by transmitting and receiving according to the highest specifications set forth by the FCC. We have rated this phone to operate at a maximum distance with the qualification that the range depends upon the environment in which the telephone is used. Many factors limit range, and it would be impossible to include all the variables in our rating. The Maximum Range rating of this phone is meant to be used as a means of comparison against other range claims.
PRECAUTIONS & WARRANTY [79]www.uniden.comTelephone Line ProblemsThe FCC has granted the telephone company the right to disconnect service in the event that your phone causes problems on the telephone line. Also, the telephone company may make changes in facilities and services which may affect the operation of your unit. However, your telephone company must give adequate notice in writing prior to such actions to allow you time for making necessary arrangements to continue uninterrupted service. If you are having trouble with your telephone service, you must first disconnect your phone to determine if it is the cause of your problem. If you determine that it is the cause, you must leave it disconnected until the trouble has been corrected.Radio InterferenceRadio interference may occasionally cause buzzing and humming in your cordless handset, or clicking noises in the base. This interference is caused by external sources such as TV, refrigerator, vacuum cleaner, fluorescent lighting, or electrical storm. Your unit is NOT DEFECTIVE. If these noises continue and are too distracting, please check around your home to see what appliances may be causing the problem. In addition, we recommend that the base not be plugged into a circuit that also powers a major appliance because of the potential for interference. Be certain that the antenna on the unit is fully extended when needed.In the unlikely event that you consistently hear other voices or distracting transmissions on your phone, you may be receiving radio signals from another cordless telephone or other source of interference. If you cannot eliminate this type of interference, you need to change to a different channel.Finally, it should be noted that some cordless telephones operate at frequencies that may cause interference to nearby TVs and VCRs. To minimize or prevent such interference, the base of the cordless telephone should not be placed near or on top of a TV or VCR. If interference is experienced, moving the cordless telephone farther away from the TV or VCR will often reduce or eliminate the interference.More than One Cordless TelephoneIf you want to use more than one cordless telephone in your home, they must operate on different channels. Press the channel key to select a channel that provides the clearest communication.Cordless Telephone PrivacyCordless telephones are radio devices. Communications between the handset and base of your cordless telephone are accomplished by means of radio waves which are broadcast over the open airways.Because of the inherent physical properties of radio waves, your communications can be received by radio receiving devices other than your own cordless telephone unit. Consequently, any communications using your cordless telephone may not be private.Installation ConsiderationsSelecting a LocationBefore choosing a location for your new phone, there are some important guidelines you should consider: The location should be close to both a phone jack and continuous power outlet. (A continuous power outlet is an AC outlet which does not have a switch to interrupt its power.) Keep the base and handset away from sources of electrical noise such as motors or fluorescent lighting. Be sure there is sufficient space to fully extend the base antenna. The base can be placed on a desk or tabletop or mounted on a standard telephone wall plate. You should charge your new phone for 17-20 hours before completing the installation or using the handset.Telephone Line OutletsThere are two types of phone outlets:Modular JackMost phone equipment available now uses modular jacks. Phone cords are fitted with a molded plastic connector which plugs into this type of jack. If you do not have modular phone jacks, contact your local telephone company for information about their installation.Hardwired JackSome equipment is wired directly to a phone jack, and these types of installations require a modular jack converter. This type of installation is not difficult; however, you should contact your Uniden telephone dealer or a telephone supply store for advice about the proper adapter or converter for your particular situation.Connecting the Telephone CordsConsider these safety guidelines before connecting the telephone cords:Caution! Never install telephone wiring during a lightning storm. Never touch uninsulated telephone wires or terminals unless the telephone line has been disconnected. Use caution when installing or modifying telephone lines.Applying Power to the BaseThis phone requires an AC outlet, without a switch to interrupt power, and the included AC adapter. To relieve strain on the DC plug when the phone is placed on a desk or table, wrap the power cord around the strain relief notch on the bottom of the base.NOTE: Place the power cord so that it does not create a trip hazard, or where it could become chafed and create a fire or other electrical hazards.One Year Limited WarrantyImportant: Evidence of original purchase is required for warranty service.WARRANTOR: UNIDEN AMERICA CORPORATION ("Uniden") ELEMENTS OF WARRANTY: Uniden warrants, for one year, to the original retail owner, this Uniden Product to be free from defects in materials and craftsmanship with only the limitations or exclusions set out below.WARRANTY DURATION: This warranty to the original user shall terminate and be of no further effect 12 months after the date of original retail sale. The warranty is invalid if the Product is(A) damaged or not maintained as reasonable or necessary, (B) modified, altered, or used as part of any conversion kits, subassemblies, or any configurations not sold by Uniden, (C) improperly installed, (D) serviced or repaired by someone other than an authorized Uniden service center for a defect or malfunction covered by this warranty, (E) used in any conjunction with equipment or parts or as part of any system not manufactured by Uniden, or (F) installed or programmed by anyone other than as detailed by the owner's manual for this product.STATEMENT OF REMEDY: In the event that the product does not conform to this warranty at any time while this warranty is in effect, warrantor will either, at its option, repair or replace the defective unit and return it to you without charge for parts, service, or any other cost (except shipping and handling) incurred by warrantor or its representatives in connection with the performance of this warranty. Warrantor, at its option, may replace the unit with a new or refurbished unit. THE LIMITED WARRANTY SET FORTH ABOVE IS THE SOLE AND ENTIRE WARRANTY PERTAINING TO THE PRODUCT AND IS IN LIEU OF AND EXCLUDES ALL OTHER WARRANTIES OF ANY NATURE WHATSOEVER, WHETHER EXPRESS, IMPLIED OR ARISING BY OPERATION OF LAW, INCLUDING, BUT NOT LIMITED TO ANY IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. THIS WARRANTY DOES NOT COVER OR PROVIDE FOR THE REIMBURSEMENT OR PAYMENT OF INCIDENTAL OR CONSEQUENTIAL DAMAGES. Some states do not allow this exclusion or limitation of incidental or consequential damages so the above limitation or exclusion may not apply to you.LEGAL REMEDIES: This warranty gives you specific legal rights, and you may also have other rights which vary from state to state. This warranty is void outside the United States of America and Canada.PROCEDURE FOR OBTAINING PERFORMANCE OF WARRANTY: If, after following the instructions in the owner's manual you are certain that the Product is defective, pack the Product carefully (preferably in its original packaging). The Product should include all parts and accessories originally packaged with the Product. Include evidence of original purchase and a note describing the defect that has caused you to return it. The Product should be shipped freight prepaid, by traceable means, to warrantor at: Uniden America CorporationParts and Service Division4700 Amon Carter Blvd.Fort Worth, TX 76155(800) 297-1023, 8 a.m. to 5 p.m. CST, Monday through FridayPRECAUTIONS & WARRANTY
[80] I.C. NOTICEwww.uniden.comI.C. NoticeTERMINAL EQUIPMENTNOTICE: This equipment meets the applicable Industry Canada Terminal Equipment Technical Specifications.This is confirmed by the registration number. The abbreviation, IC, before the registration number signifies that registration was performed based on a Declaration of Conformity indicating that Industry Canada technical specifications were met. It does not imply that Industry Canada approved the equipment.NOTICE: The Ringer Equivalence Number (REN) for this terminal equipment is marked on the equipment itself. The REN assigned to each terminal equipment provides an indication of the maximum number of terminals allowed to be connected to a telephone interface. The termination on an interface may consist of any combination of devices subject only to the requirement that the sum of the Ringer Equivalence Numbers of all the devices does not exceed five.RADIO EQUIPMENTThe term "IC:" before the radio certification number only signifies that Industry Canada technical specifications were met.Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. "Privacy of communications may not be ensured when using this telephone".I.C. NOTICE
INDEX [81]www.uniden.comIndex0 - 93-way conferencing . . . . . . . . . 364-way conferencing . . . . . . . . . 6816 ring options . . . . . . . . . . . . 23AAnnounce only feature . . . . . . . 56Answering systemDeleting a message . . . . . . . . 60Playing your messages . . . . . . 59Recording a conversation . . . . 61Remote access . . . . . . . . . . . 62Repeating a message . . . . . . . 59Skipping a message . . . . . . . . 60Turning On/Off . . . . . . . . . . . 51Anykey answer . . . . . . . . . . . . . 24Area code . . . . . . . . . . . . . . . . 28AutoTalk . . . . . . . . . . . . . . . . . 24BBanner . . . . . . . . . . . . . . . . . . 24BatteryPreparing and charging . . . . . 10Replacement and handling . . . 72Beltclip . . . . . . . . . . . . . . . . . 71Booster . . . . . . . . . . . . . . . . . 35CCaller IDCaller ID service . . . . . . . . . . 45Calling . . . . . . . . . . . . . . . . 48Call Waiting . . . . . . . . . . . . . 36Deleting . . . . . . . . . . . . . . . 47Setting . . . . . . . . . . . . . . . . 48Storing . . . . . . . . . . . . . . . . 48Using . . . . . . . . . . . . . . . . . 48Viewing . . . . . . . . . . . . . . . . 46Call transfer feature . . . . . . . . . 69Chain dialing . . . . . . . . . . . . . . 44Clock . . . . . . . . . . . . . . . . . . . 27DDeluxe Call Waiting features . . . . 49De-register the handset . . . . . . . 28Dialing mode . . . . . . . . . . . . . . 13Digital security code . . . . . . . . . 71Distinctive ringer . . . . . . . . . . . 24E, F, G, HEarpiece volume . . . . . . . . . . . . 33Expanding your phone . . . . . . . . 65General information . . . . . . . . . 73Hands-free conversation . . . . . . 30Headset installation . . . . . . . . . 71I, J, K, LI.C. Notice. . . . . . . . . . . . . . . . 80Important safety instructions . . . 78Intercom . . . . . . . . . . . . . . . . . 68Key touch tone. . . . . . . . . . . . . 25Languagehandset . . . . . . . . . . . . . . . . 25base . . . . . . . . . . . . . . . . . . 57Liquid damage . . . . . . . . . . . . . 77M, N, OMaintenance . . . . . . . . . . . . . . 72Making a call . . . . . . . . . . . . . . 30Mute . . . . . . . . . . . . . . . . . . . 34New message LED . . . . . . . . . . . 36Outgoing message . . . . . . . . . . 51P, QPhonebookEditing . . . . . . . . . . . . . . . . 43Erasing . . . . . . . . . . . . . . . . 43Making calls . . . . . . . . . . . . . 42Storing . . . . . . . . . . . . . . . . 37Viewing . . . . . . . . . . . . . . . . 41Precautions . . . . . . . . . . . . . . . 78RReceiving a call . . . . . . . . . . . . 30Redialing a call. . . . . . . . . . . . . 32Register the handset . . . . . . . . . 66Remote accessaway from home . . . . . . . . . . 62from your handset . . . . . . . . . 63Replacing the base . . . . . . . . . . 70Ringer Adjust, base . . . . . . . . . . . . . 52Adjust, handset . . . . . . . . . . . 33mute . . . . . . . . . . . . . . . . . . 33DND . . . . . . . . . . . . . . . . . . . 33Room Monitor. . . . . . . . . . . . . . 23SSetting upbase unit . . . . . . . . . . . . . . . 12extra handset . . . . . . . . . . . . 66handset . . . . . . . . . . . . . . . . 19Speed dialing . . . . . . . . . . . . . . 42T, U, V, W, X, Y, ZTransferring a call . . . . . . . . . . . 69Voice memo . . . . . . . . . . . . . . . 61Warranty . . . . . . . . . . . . . . . . . 79
At Uniden, we'll take care of you!If you need any assistance with this product, please call our Customer Hotline at1-800-297-1023PLEASE DO NOT RETURN THIS PRODUCT TO THE PLACE OF PURCHASE.Our Uniden representatives will be happy to help you with any matters regardingthe operation of this unit, available accessories, or any other related matters.Thank you for purchasing a Uniden product.Hours: M-F 8:00 AM to 5:00 PM CST.For information on the accessibility features of this product, please call1-800-874-9314 (V/TTY)www.uniden.comMay be covered under one or more of the following U.S. patents:4,523,058 4,595,795 4,797,916 5,381,460 5,426,690 5,434,9055,491,745 5,493,605 5,533,010 5,574,727 5,581,598 5,650,7905,660,269 5,661,780 5,663,981 5,671,248 5,696,471 5,717,3125,732,355 5,754,407 5,758,289 5,768,345 5,787,356 5,794,1525,801,466 5,825,161 5,864,619 5,893,034 5,912,968 5,915,2275,929,598 5,930,720 5,960,358 5,987,330 6,044,281 6,070,0826,125,277 6,253,088 6,314,278 6,418,209?

Navigation menu