Uniden America UT395 CB TRANSCEIVER WITH WEATHER ALERT User Manual

Uniden America Corporation CB TRANSCEIVER WITH WEATHER ALERT

Contents

User Manual

Owner’s ManualPrinted in VietnamU01UT393ZZZ(0)®PC787
CONTENTSSAFETY NOTICE .......................................................................... 4UNPACKING ................................................................................ 4DESCRIPTION ............................................................................. 5FEATURES ...................................................................................................... 5EMERGENCY OPERATION ......................................................... 6CONTROLS AND FUNCTIONS .................................................... 6INSTALLATION ............................................................................ 8 MOBILE INSTALLATION .............................................................................. 8Mobile Antenna ........................................................................................... 9Wireless CB Microphone Installation (Optional) ........................................ 9Connecting the Power Cords ...................................................................... 9Ground Information ................................................................................. 10USING YOUR PC787 .................................................................. 10TURN PC787 ON/OFF .................................................................................. 10CB MODE ...................................................................................................... 10 Basic Settings ........................................................................................... 10Calibrate Standing Wave Ratio (SWR) ..................................................... 11PA MODE ...................................................................................................... 12PREVENTIVE MAINTENANCE .................................................. 12MAINTENANCE ......................................................................... 13TROUBLESHOOTING ............................................................... 13SERVICING YOUR TRANSCEIVER ........................................... 14
© 2013 Uniden America CorporationUniden is a registered trademark of Uniden America Corporation.Bearcat is a registered trademark of Uniden America Corporation.Features, specications, and availability of optional accessories are all subject to change without notice.SPECIFICATIONS ....................................................................... 14RADIO CODE DEFINITIONS ..................................................... 1510CODES ..................................................................................................... 15FCC PART 15 INFORMATION ................................................... 17TWOYEAR EXTENDED WARRANTY ...................................... 17
4SAFETY NOTICEThe antenna used for this radio must be properly installed and maintained and must provide a separation distance of at least 34 cm (13.4 Inches) from all persons and must not be collocated or operated in conjunction with any other antenna or transmitter. Never transmit if any person is closer than the specified distance to the antenna. Note that Uniden does not specify or supply any antenna with this transceiver. While a 0 dBi gain antenna is normal for a typical installation, the above limit applies to any antenna with up to 3 dBi gain.L’appareil est conforme aux normes d’Industrie Canada. Son fonctionnement est soumis aux deux conditions suivantes : (1) Ce dispositif ne doit pas causer d’interférences et (2), il doit pouvoir accepter les interférences, incluant celles pouvant nuire à son fonctionnement normal. Changes or modifications to this product or use of accessories not expressly approved by Uniden, or operation of this product in any way other than as provided in the Uniden Owner’s Manual could void your authority to operate this product.A complete Owner’s Manual in French can be downloaded from http://www.uniden.com/.UNPACKINGYour PC787 contains the following: PC787 CB 2-way mobile radio Microphone Mounting Bracket Kit DC Power Cord Reference Guide Part 95 Subpart D (FCC Rules) If any items are missing or damaged, contact your place of purchase immediately.
5DESCRIPTION Your PC787 represents the highest quality communications device designed for use in the Citizens Band Radio Service. It will operate on any of the 40 AM frequencies authorized by the Federal Communications Commission (FCC). The Citizens Band Radio Service is under the jurisdiction of the Federal Communications Commission (FCC). Any adjustments or alterations which would alter the performance of the transceiver's original FCC type acceptance, or which would change the frequency determining method, are strictly prohibited. Replacement or substitution of crystal, transistors, ICs, regulator diodes, or any other part of a unique nature, with parts other than those recommend by Uniden, may cause violations of the technical regulations in Part 95 of the FCC Rules or in violation of type acceptance requirements in Part 2 of the rules. FEATURES CB AM 40 channels (4W) 7 weather channels with Weather Alert Public Address function (External speaker required - not provided) Automatic Noise Limiter Noise Blanker Transmit/Receive LED (Red and yellow-green) CH9 and CH19 direct tune Dimmer control (High/Medium/Low) Variable RF Gain Variable MIC Gain Variable Tone control Multifunction Meter (RF, Signal Strength, and SWR) Variable Volume control Variable Squelch control 6-pin microphone jack
6EMERGENCY OPERATION 1. Move the 9/19/NORM switch to 9; the radio automatically tunes to Channel 9 and disables the channel selector. 2. Press and hold PTT and speak clearly. Release PTT after speaking.3. If there is no response, move the 9/19/NORM switch to 19; the radio automatically tunes to Channel 19.4. Press and hold PTT and speak clearly. Release PTT after speaking.5. If there is still no response, move the 9/19/NORM switch to NORM and ask that party to relay your emergency broadcast on Channel 9. All channels except Channel 9 may be used for normal communication. The FCC reserves Channel 9 for emergencies involving the immediate safety of individuals or protection of property. Use Channel 9 to render assistance to a motorist.This is an FCC rule and applies to all CB radio operators. CONTROLS AND FUNCTIONS161412109 11 15132 87654311. Multifunction meter. When receiving, the meter shows the received signal strength. Use CAL and SWR to tune an antenna for best performance.2. S/RF/CAL/SWR switch: Selects S/RF, CAL, and SWR to be measured through the multifunction meter.3. CB/WX/PA switch: Selects CB (Citizens Band) or WX (Weather) modes, or activates the PA (Public Address) feature.
7Do not use the PA function unless an external speaker is connected. 4. NB+ANL/ANL/OFF switch: Activates the Noise Blanker (NB) and Automatic Noise Limiter (ANL) features. NB reduces external noise and ANL reduces background noise from the car engine and other sources. OFF turns o both the NB and ANL features.5. 9/19/NORM switch: Move the switch to select emergency channel 9, channel 19, or standard CB channels.All channels except Channel 9 may be used for normal communication. The FCC reserves Channel 9 for emergencies involving the immediate safety of individuals or protection of property. Use Channel 9 to render assistance to a motorist.6. HIGH/MED/LOW switch: Adjust LCD backlight and all illuminations brightness.7. RX/TX LED: Indicates whether the radio is transmitting (red) or receiving (yellow-green).8. Channel Indicator: Displays the channel currently in use.9. 6-Pin Microphone Jack: Connects the radio to the detachable microphone (included). 10. Channel Selector knob: Turn this knob to select CB or Weather channels.11. RF Gain inner knob: Turn the inner knob to reduce interference in strong signal areas.12. MIC Gain outer knob: Turn the outer knob to adjust the microphone sensitivity.13. CAL inner knob: Turn the inner knob to calibrate the meter for Standing Wave Ratio (SWR) measurements.14. TONE outer knob: Turn the outer knob to change the tone quality.15. VOL inner knob: Turn the inner knob to turn the radio on and o and to adjust the volume.16. SQUELCH outer knob: Turn the outer knob to reduce background noise when there is no incoming signal.
817 18 1920212217. Antenna socket: Connects antenna to the unit.18. PA SP: Connects optional external 8-ohm, over 5-watt speaker for use as a public address system. To prevent acoustic feedback, separate the microphone from the speaker when operating the PA at high output levels. 19. EXT. SP: Connects optional external 8-ohm, over 5-watt speaker for CB and WX operation. When the external speaker is plugged in, the internal speaker is o. 20. POWER: Connects DC power to transceiver. 21. Fuse. 22. PTT: Push-to-Talk.INSTALLATION MOBILE INSTALLATION Plan the location of the transceiver and microphone bracket before beginning installation. 1. Select a location that is convenient for operating the radio but does not interfere with the driver or passenger. 2. Install bracket with self-tapping screws provided. 3. Connect power cords (see page 9). 4. Attach the microphone bracket to side of the radio. 5. Attach radio to bracket.
9Mobile AntennaWARNING! The antenna used for this radio must be installed at least 13.4 inches (34 cm) away from all persons. The antenna must not be collocated or used with any other antenna or transmitter. CAUTION: Never operate your radio with no antenna or with a damaged antenna cable. This can damage the radio.You must purchase an antenna to operate this radio. Because the maximum power output of the transmitter is limited by the FCC, the quality of your antenna is very important. To achieve the maximum transmission distance, Uniden strongly recommends that you install only a high quality antenna. You have just purchased a superior transceiver - don't diminish its performance by installing an inferior antenna. Only a properly matched antenna system will allow maximum power transfer from the 50 ohm transmission line to the radiating element. Your Uniden dealer is qualified to help you select the proper antenna for your requirements. A whip style antenna may be used for automobile installation. A short ‘loaded’ whip antenna is easier to install on an automobile, but its efficiency is less than that of a full quarter-wave whip antenna. Wireless CB Microphone Installation (Optional)Your PC787 is compatible with Uniden’s BC906W Wireless CB Microphone. With a range up to 300 feet, the BC906W allows you to use your CB to communicate even when you need to get out of your vehicle. Follow the instructions provided in the BC906W kit to install the wireless microphone.Connecting the Power Cords Uniden recommends connecting the power lead to the Ignition Switch Accessory Terminal. This way, the transceiver is automatically turned off when the ignition switch is turned off. As an alternative, the power cord may be connected to an available terminal on the fuse block or to a point in the wiring harness. However,
10caution must be taken to prevent a short circuit. If in doubt, contact your vehicle dealer for information. Ground Information This transceiver may be installed and used in any 12-volt DC negative ground system vehicle. Negative Ground System With a negative ground system, the negative (-) battery terminal is usually connected to the vehicle motor block. Connect the red DC power cord from the transceiver to the positive (+) battery terminal or other convenient point. Then connect the black power cord to the vehicle chassis or negative (-) battery terminal.USING YOUR PC787TURN PC787 ON/OFFTurn the VOL knob clockwise until the unit turns on and the display backlight turns on.Turn the VOL knob counter-clockwise to turn the unit off.CB MODEBe sure that the power source, antenna, and microphone are properly connected before proceeding. Basic Settings1. Turn unit on. Set volume to a comfortable level. 2. Set switch to CB.3. Select a CB channel (CH knob). 4. Set noise limitations as desired (ANL/NB switch).5. Adjust squelch.• Turn SQ knob fully clockwise so only strong signals can get through.
11• Turn SQ knob fully counterclockwise until you hear a hiss. Everything gets through - noise, weak signals, and strong signals• Turn SQ knob clockwise until the hiss stops. Only clearer signals get through. Set SQUELCH only when the radio is not receiving a strong signal. 6. Set the S/RF/SWR/CAL switch to S/RF.7. Press and hold PTT and check the multifunction meter. It will show the RF output power. Adjust as needed. 8. Turn RF knob to set RF gain sensitivity. Normally, the knob is turned clockwise to maximum.9. Turn MIC knob to adjust microphone sensitivity for transmission. Normally, the knob is turned clockwise to maximum.10. Set the brightness (HIGH, MED, or LOW).The Weather Alert system monitors the last weather channel you were on before you changed to CB mode. It sounds a seven-second signal when it decodes a severe weather alert issued for your area. Change to Weather mode for details.Calibrate Standing Wave Ratio (SWR) SWR calibration monitors the coaxial cable quality and all RF connections.Do not calibrate in an enclosed area such as a garage. Do not stand near the antenna while calibrating. 1. Set CB/WX/PA to CB and select channel 20.2. Set S/RF/SWR/CAL to CAL.3. Press and hold PTT on the mic. The needle on the multipurpose meter will begin to move.4. Turn the CAL knob until the meter needle moved into the red calibration block. When the needle moves towards the right-hand side of the block, stop.5. Still holding PTT, move the S/RF/SWR/CAL to SWR. The needle should move back to the left-hand side of the meter. Ideally, it should be as far left a possible. If the reading is higher than 3, adjust the antenna height.6. Release PTT.
127. Repeat the steps for channel 1 and channel 40 to complete calibration.The readings will be slightly higher for channel 1 and channel 40 than for channel 20.WEATHER MODE WX MODEYour radio combines a CB radio with a Weather radio and a Weather Alert system. The Weather radio continually broadcasts weather conditions when you are in Weather mode. Weather Alert function does not work in Weather mode.1. Set the CB/WX/PA switch to WX. Your radio is now in Weather radio mode.2. Turn the channel selector knob to select 1 of 7 weather channels.ANL and NB do not work in WX mode. PA MODEUsing the PA mode requires an optional speaker. 1. Switch to PA. 2. Press and hold PTT to speak.3. Release when nished. To prevent acoustic feedback, separate the microphone from the speaker when operating the PA at high output levels.If you are in PA mode but not pressing PTT, the radio receives CB transmissions and transmits them through the PA speaker. You cannot respond to the transmission.PREVENTIVE MAINTENANCE Every six months: 1. Check the SWR. 2. Be sure all electrical connections are tight. 3. Inspect antenna coaxial cable for wear or breaks in shielding. 4. Be sure all screws and mounting hardware are tight.
13MAINTENANCE The PC787 is designed to give you years of trouble-free service. There are no user-serviceable parts inside. Except for the fuse in the DC power cord, no maintenance is required.To replace a blown fuse: 1. Press ends of the fuse holder together. Twist to open. Carefully separate the two pieces. 2. Remove the fuse and inspect. If blown, replace with the same type fuse. Use only the fuse specied for your PC787. Failure to do so may void your warranty. TROUBLESHOOTING In the event of system malfunction, perform the following procedures: Problem SuggestionUnit does not power up Check power cord connections. Check fuse. Check vehicle electrical system.No reception Check microphone connection. Set CB/WX/PA to CB. Check VOL and SQ. Check antenna. Check antenna connection. Adjust RF Gain. Poor Reception Check VOL and SQ. Be sure antenna SWR is normal.Adjust RF Gain. No Transmission Set CB/WX/PA switch to CB. Check microphone connection.Adjust MIC Gain. Low Transmission Adjust MIC Gain. Calibration does not move the meter needle to the left sideAdjust the antenna height.Check all antenna connections.
14If you do not get satisfactory results after performing these checks, call the Uniden Customer Service Center at 1-800-297-1023, 8:00 a.m. to 5:00 p.m. CST, Monday through Friday.SERVICING YOUR TRANSCEIVER Technical information, diagrams, and charts are provided on request. It is the user's responsibility to see that this radio is operating at all times in accordance with the FCC Citizens Radio Service regulations. We highly recommend that you consult a qualified radio/telephone technician for servicing and aligning this CB radio product. When ordering parts, be sure to specify the correct model number and serial number of the unit. SPECIFICATIONSGENERALChannel: 40Frequency Range: 26.965 - 27.405 MHzFrequency Control: PLL SynthesizerAntenna Impedance: 50 ohmsPower Input: 13.8VDCCurrent DrainTX: AM Full Modulation: 2.1A (max)RX: At no signal: 400mAOperating Temperature: -22°F to 140°F (-30°C to 60°C)Accessories: DC Power Cord Microphone Microphone HangerMounting BracketSize (W x D x H): 7.25 in. x 7.5 in. x 2.25 in. (without knobs and jacks)(184.149 mm x 190.50 mm x 57.15 mm)Weight: 2.2 PoundsTRANSMITTEROutput Power: 4 watts
15TRANSMITTER (Cont’d)Emission Type: 6A3Hum and Noise: Better than 40 dBFrequency Tolerance: ±0.002%Modulation Percentage (Peak): 100%Spurious Rejection: -70 dBOutput Impedance: 50 ohm, unbalancedRECEIVERSensitivity at 10 dB S+N/N: 0.5 µVSensitivity at 500 mW Audio Output: 0.5 µVSquelch Threshold: 0.5 µVAntenna Impedance: 50 ohmsSquelch Tight: 1000 µVSignal Meter S-9: 100 µVAudio Output Power (max.): 5 wattsAudio Output (10% Dist.): 4 wattsAdjacent Channel Rejection: 60dBImage Rejection: 90dBInternal Speaker Impedance: 16 ohmsExternal Speaker Impedance: 8 ohmsPUBLIC ADDRESSOutput Power at 10% Distortion: 4 watts Specications shown are typical and subject to change without notice. RADIO CODE DEFINITIONS 10CODESThe following list contains common “10-Codes” used by CB radio operators for faster communication and better understanding. Code Meaning Code Meaning10-1 Received poorly 10-34 Trouble at this station 10-2 Receiving well 10-35 Condential information 10-3 Stop transmitting 10-36 Correct time is
16Code Meaning Code Meaning10-4 OK, message received 10-37 Wrecker needed at 10-5 Relay message 10-38 Ambulance needed at 10-6 Busy, stand by 10-39 Your message is delivered 10-7 Out of service, leaving air 10-41 Please turn to channel 10-8 In service, subject to call 10-42 Trac accident at 10-9 Repeat message 10-43 Trac tie up at 10-10 Transmission completed, standing by 10-44 I have a message for you 10-11 Talking too rapidly 10-45 All units within range please report 10-12 Visitors present 10-50 Break channel 10-13 Advise Weather/ Road conditions 10-60 What is next message number 10-16 Make pickup at 10-62 Unable to copy, use phone 10-17 Urgent business 10-63 Net directed to 10-18 Anything for us? 10-64 Net clear 10-19 Nothing for you, return to base 10-65 Awaiting your next message/as-signment 10-20 My location is 10-67 All units comply 10-21 Call by telephone 10-70 Fire at 10-22 Report in person to 10-71 Proceed with transmission in sequence 10-23 Stand by 10-77 Negative contact 10-24 Completed last assignment 10-81 Reserve hotel room for 10-25 Can you contact 10-82 Reserve room for 10-26 Disregard last information 10-84 My telephone number is 10-27 I am moving to channel 10-85 My address is 10-28 Identify your station 10-91 Talk closer to microphone 10-29 Time is up for contact 10-93 Check my frequency on this channel 10-30 Does not conform to FCC rules 10-94 Please give me a long count 10-32 I will give you a radio check 10-99 Mission completed, all units secure
17Code Meaning Code Meaning10-33 EMERGENCY TRAFFIC 10-200 Police needed at FCC PART 15 INFORMATIONThis device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. Privacy of communications may not be ensured when using this radio. TWOYEAR EXTENDED WARRANTY Important: Evidence of original purchase is required for warranty service. WARRANTOR: UNIDEN AMERICA CORPORATION (“Uniden”) ELEMENTS OF WARRANTY: Uniden warrants, for two years, to the original retail owner, this Uniden Product to be free from defects in materials and craftsmanship with only the limitations or exclusions set out below. WARRANTY DURATION: This warranty to the original user shall terminate and be of no further effect two years after the date of original retail sale. The warranty is invalid if the Product is (A) damaged or not maintained as reasonable or necessary, (B) modified, altered, or used as part of any conversion kits, subassemblies, or any configurations not sold by Uniden, (C) improperly installed, (D) serviced or repaired by someone other than an authorized Uniden service center for a defect or malfunction covered by this warranty, (E) used in any conjunction with equipment or parts or as part of any system not manufactured by Uniden, or (F) installed or programmed by anyone other than as detailed by the owner’s manual for this product. STATEMENT OF REMEDY: In the event that the product does not conform to this warranty at any time while this warranty is in effect, warrantor will either, at its option, repair or replace the defective unit and return it to you without charge for parts, service, or any other cost (except shipping and handling) incurred by warrantor or its representatives in connection with the performance of this warranty. Warrantor, at its option, may replace the unit with a new or refurbished unit. THE LIMITED WARRANTY SET FORTH ABOVE IS THE SOLE AND ENTIRE WARRANTY PERTAINING TO THE PRODUCT AND IS IN LIEU OF AND EXCLUDES ALL OTHER WARRANTIES OF ANY NATURE WHATSOEVER, WHETHER EXPRESS, IMPLIED OR ARISING BY OPERATION OF LAW, INCLUDING, BUT NOT LIMITED TO ANY IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. THIS WARRANTY DOES NOT COVER OR PROVIDE FOR THE REIMBURSEMENT OR PAYMENT OF INCIDENTAL OR CONSEQUENTIAL DAMAGES.
18Some states do not allow this exclusion or limitation of incidental or consequential damages so the above limitation or exclusion may not apply to you. LEGAL REMEDIES: This warranty gives you specific legal rights, and you may also have other rights which vary from state to state. This warranty is void outside the United States of America. PROCEDURE FOR OBTAINING PERFORMANCE OF WARRANTY: If, after following the instructions in the owner’s manual you are certain that the Product is defective, pack the Product carefully (preferably in its original packaging). The Product should include all parts and accessories originally packaged with the Product. Include evidence of original purchase and a note describing the defect that has caused you to return it. The Product should be shipped freight prepaid, by traceable means, to warrantor at: Uniden America Corporation 743 Henrietta Creek Rd. Roanoke, TX 76262(800) 297-1023, 8 a.m. to 5 p.m., Central, Monday through Friday

Navigation menu