Uniden America UT401 CB Transceiver User Manual PRO401HH

Download:
Mirror Download [FCC.gov]
Document ID	2291598
Application ID	V+5ZE5tnoszqwQfipFotIA==
Document Description	PRO401HH User Manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	37.55kB (469335 bits)
Date Submitted	2014-06-11 00:00:00
Date Available	2014-06-11 00:00:00
Creation Date	2014-02-12 12:04:38
Producing Software	Adobe PDF Library 9.0
Document Lastmod	2014-03-21 13:41:12
Document Title	PRO401HH User Manual
Document Creator	Adobe InDesign CS4 (6.0.6)

PRO401HH
Handheld CB Radio
Printed in Vietnam
xxxxxxxxxxx(0)
INTRODUCTION
The PRO401 radio is a mobile radio designed for use in the Citizens Band
(CB) Radio Service. It will operate on any of the 40 AM frequencies authorized
by the Federal Communications Commission (FCC). Your radio features a
superheterodyne circuit with Phase Locked Loop techniques to assure precise
frequency control.
Features
►► Condenser microphone.
►► Ceramic filter: Delivers greater selectivity and reduces adjacent channel
interference.
►► AGC (Automatic Gain Control) for a constant sound level.
►► Automatic modulation control for a constant audio transmit modulation
level.
►► Low distortion IC audio circuit.
►► Automatic noise limiter to reduce pulse noise.
►► “HI-LO” switch: Adjusts output power.
►► Antenna with BNC connector.
►► Jack for external power source and battery charger.
Safety Notice
►► Do not expose the PRO401HH to water or extreme temperatures.
►► Do not leave batteries installed over a long period of time as leakage may
occur and cause damage to the radio.
►► Never use different batteries from the ones suggested.
►► Never use harsh chemicals to clean this radio. Use a damp soft cloth.
FCC Part 15 Compliance Information
This device complies with FCC Part 15 standard(s). Operation is subject to
the following two conditions: (1) this device may not cause interference, and
(2) this device must accept any interference, including interference that may
cause undesired operation of the device.
Changes or modifications to this product or use of accessories not expressly
approved by Uniden, or operation of this product in any way other than as
provided in the Uniden Owner’s Manual could void your authority to operate
this product.
A complete Owner’s Manual in French can be downloaded from http://www.
uniden.com/.
Cet appareil est conforme la norme d’Industrie Canada exempt de licence
RSS (s). Son fonctionnement est soumis aux deux conditions suivantes : (1)
cet appareil ne peut pas provoquer d’interférences, et (2) cet appareil doit
accepter toute interférence, y compris les interférences qui peuvent causer un
mauvais fonctionnement de l’appareil.
Tous les changements apportés à cet appareil, s’ils ne sont pas expressément
approuvés par Uniden ou toute utilisation de celui-ci d’une autre manière
que celle décrite dans ce guide peut annuler votre autorisation de le faire
fonctionner.
Un guide d’utilisation en français peut être téléchargé à l’adresse suivante :
http://www.uniden.com/.
Uniden contact information
You can get answers 24/7 at our website: www.uniden.com.
If You
Contact Uniden’s
Phone
have a question or problem
Customer Care Line*
800-297-1023
need a part or accessory
Parts Department*
800-554-3988
need special assistance due
to a disability
Accessibility Help Line
800-874-9314
(voice or TTY)
*During regular business hours, Central Standard Time. Visit our website for detailed
business hours.
INCLUDED IN YOUR PACKAGE
If any of these items are missing or damaged, immediately contact your place
of purchase or Uniden’s Parts Department.
TX
BATT. LOW
EXT PWR
HI
MIC
PRO401HH
PRO401HH Radio
Antenna
DC Power Input
Other printed materials
PARTS OF THE RADIO
Front
SQUELCH
VOLUME
TX
PTT
BATT. LOW
EXT PWR
HI
MIC
SPKR
MIC
10
DC 13.8V
CHARGE
HI
LOW
PRO401HH
Belt Clip
Battery Compartment
11
12
NOTE: A switch inside the compartment lets you select rechargeable or
Alkaline batteries.
Channel UP/DOWN
Selects which channel the radio will transmit or receive on.
Push to Talk
Allows you to transmit.
5
Antenna Jack
Connect the detachable antenna to this jack.
Squelch knob
Adjusts the level at which the radio squelches or suppresses weak radio
signals. To filter out weaker signals and background noise, turn the knob
clockwise to increase the squelch level. To decrease the squelch level so
you can hear weaker radio signals, turn the knob counter-clockwise.
Volume Control
Powers on the radio and adjusts the volume.
Microphone
Speak into the microphone when transmitting.
Speaker Jack
Connects to an external speaker (not includerd). The internal speaker is
disabled.
10 Microphone Jack
Connects to an external microphone (not included).
11 13.8 V DC External Power Jack
Provides power to the unit. you can use external power sources such as
a car battery to power the unit and to recharge the Ni-Cd rechargeable
batteries.
12 Transmit Power Switch (HI/LOW)
Select a power output level for transmission.
NOTE: FCC rules reserve Channel 9 for motorist assistance and other
emergency communications. Channel 9 should only be used in situations
where there is immediate danger to the safety of individuals or the
protection of property.
Make sure you have read and understood part 95 of the FCC rules and
regulations before using the transmitter.
SET UP
Install Antenna
Install the included rubber antenna onto the radio.
The PRO401HH can also use any type of 50 Ω / 27 MHz band antenna.
Although a telescoping antenna might provide better transmission and
receiving, it is not as compact or easy to use as the antenna included in the
package.
Connecting to Power
Your PRO401HH can operate on DC power or batteries.
DC Power
Plug the DC power coverter into the PRO401HH.
Plut the other end into your vehicle’s cigarette lighter/DC power conversion
plug.
The red power LED is steady on when the unit is connected to external
power (not batteries).
WARNING! DO NOT connect this equipment to a power supply if you are
not absolutely certain of the grounding type!
Battery Power
You can use either 9 non-rechargeable alkaline batteries or 9 rechargeable NiCD batteries with this unit.
Open battery cover.
Set the internal switch to match the battery type you are using (either
alkaline or rechargeable (Ni-CD) batteries.
Insert the 9 batteries.
Close battery cover.
The red power LED is steady on.
Low Power Indication
The red LED blinks when battery power is low. Replace/recharge the batteries
or connect the radio to a power source.
OPERATION AND MAINTENANCE
Basic operation
Turning the
radio on
Turning the
radio off
Selecting a
channel
Changing the
volume
Transmitting
Turn the Volume knob clockwise until it clicks and the display backlight
comes on.
Turn the Volume knob counter-clockwise until it clicks and the display
backlight turns off.
Press the Channel UP or DOWN button on the side to move up or down the
channel list.
Turn the Volume knob clockwise to increase the volume; turn it counterclockwise to decrease the volume.
–– Tune the radio to the channel you want to transmit on, and listen to make
sure the channel is clear.
–– Press and hold the PTT button.
–– Hold the microphone about 2 inches away from your mouth and speak in a
normal voice.
–– Release the PTT button to listen for a response.
NOTE: Make sure you have read and understood part 95 of the FCC rules
and regulations before using the transmitter.
CB Communication Codes
The “10” code allows you to communicate easier in noisy environments. The
following table lists some of the most common codes and their meaning.
Code
10-1
10-2
10-3
10-4
10-6
10-7
10-8
10-9
10-10
10-13
10-20
10-33
10-36
10-41
Meaning
Receiving poorly
Receiving well
Stop transmiting
OK - Understood
Busy - Stand By
Out of service - Leaving air
In service - Subject to call
Please repeat
Transmission completed - Standing by
Road advice - Weather conditions
What is your location?
Emergency traffic
Exact time
Switch to channel
Code
10-62
10-70
10-200
Meaning
Cannot receive - use phone
Fire at __________
Police needed at __________
Maintenance
Clean the unit with a damp cloth only; never use harsh chemicals.
TROUBLESHOOTING
If your radio is not performing to your expectations, please try these simple
steps. If these steps don’t solve your problem, call the Uniden Customer
Service Center.
Problem:
Things to try:
Radio won’t turn on
(no power)
1. Check the radio’s power cord and all connections.
2. Check the fuse in the radio’s power cord.
3. Check your vehicle’s electrical system.
Poor reception
1. Adjust the squelch level.
2. Check the antenna, cable and connectors.
3. Check operation mode of the radio.
Background noise
1. Turn on the automatic noise limiter.
2. Adjust the squelch level.
Weak transmission
1. Check the antenna, cable and connectors.
2. Check the antenna grounding.
3. Check for corrosion on the connectors.
Service and repair information
►► Save your purchase receipt for proof of warranty.
►► When ordering parts, it is important to specify the correct model number of
this radio (PRO401HH).
►► It is the user’s responsibility to make sure the radio is operating in
accordance with the FCC Citizens Radio Service regulations at all times.
SPECIFICATIONS
General
Channels
Frequency Range
Frequency Control
Frequency Tolerance
Operating Temperature
Microphone
40 AM
26.965 to 27.405 MHz
Phase Locked Loop (PLL) synthesizer
±0.005%
14ºF to 131ºF (-10ºC to +55ºC)
Electret Type
Input Voltage
Current Drain
RX
Size
Weight
LED Meter
Transmitter
Power Output
Modulation
Freq. Response
Output Impedance
Receiver
Sensitivity
Selectivity
Image Rejection
I.F. Frequency
Automatic Gain Control
(AGC)
Squelch
Audio Output Power
Freq. Response
Distortion
Internal Speaker
13.8 V DC nom, 10.9VDC – 15.6VDC
TX full mod., 1.7A
with max. audio output, 1.7A
2.16 x 7.1 x 1.7 in (55 x 180 x 45 mm)
0.56 lbs (255 g).
Indicates relative RF output and received signal strength
4 Watts @13.8 VDC
85% - 95%
400 Hz – 2.5 KHz
50 ohms, unbalanced
<1 μV for 10 dB; (S + N) /N typical (limit 1.0μV)
6 dB @ 7kHz, 70 dB @ 10kHz typical
65 dB
Double Conversion Superheterodyne
1st - 10.965 MHz
2nd - 455 kHz
less than 10dB change in audio output for inputs from 10 to
50,000 microvolts
Adjustable; threshold less than1μV
0.5 watts max. @ 8 ohms
300 to 2000 Hz
less than 8% at 1KHz
8 ohms, 0.5 watts
Specifications and features are subject to change without notice.
FCC Part 15 Compliance Information
This device complies with part 15 of the FCC rules. Operation is subject to the following
two conditions: (1) This device may not cause harmful interference, and (2) This device
must accept any interference received, including interference that may cause undesired
operation. Privacy of communications may not be ensured when using this radio.
Changes or modifications to this product or use of accessories not expressly approved
by Uniden, or operation of this product in any way other than as provided in the Uniden
Owner’s Manual could void your authority to operate this product.
Cet appareil est conforme la norme d’Industrie Canada exempt de licence RSS (s). Son
fonctionnement est soumis aux deux conditions suivantes : (1) cet appareil ne peut pas
provoquer d’interférences, et (2) cet appareil doit accepter toute interférence, y compris
les interférences qui peuvent causer un mauvais fonctionnement de l’appareil.
Tous les changements apportés à cet appareil, s’ils ne sont pas expressément
approuvés par Uniden ou toute utilisation de celui-ci d’une autre manière que celle
décrite dans ce guide peut annuler votre autorisation de le faire fonctionner.
TWO-YEAR LIMITED WARRANTY
WARRANTOR: UNIDEN AMERICA CORPORATION (“Uniden”)
ELEMENTS OF WARRANTY: Uniden warrants, for two years, to the original retail
owner, this Uniden Product to be free from defects in materials and craftsmanship with
only the limitations or exclusions set out below.
WARRANTY DURATION: This warranty to the original user shall terminate and be
of no further effect 24 months after the date of original retail sale. The warranty is
invalid if the Product is (A) damaged or not maintained as reasonable or necessary,
(B) modified, altered, or used as part of any conversion kits, subassemblies, or any
configurations not sold by Uniden, (C) improperly installed, (D) serviced or repaired by
someone other than an authorized Uniden service center for a defect or malfunction
covered by this warranty, (E) used in any conjunction with equipment or parts or as part
of any system not manufactured by Uniden, or (F) installed or programmed by anyone
other than as detailed by the owner’s manual for this product.
STATEMENT OF REMEDY: In the event that the product does not conform to this
warranty at any time while this warranty is in effect, warrantor will either, at its option,
repair or replace the defective unit and return it to you without charge for parts,
service, or any other cost (except shipping and handling) incurred by warrantor or
its representatives in connection with the performance of this warranty. Warrantor,
at its option, may replace the unit with a new or refurbished unit. THE LIMITED
WARRANTY SET FORTH ABOVE IS THE SOLE AND ENTIRE WARRANTY
PERTAINING TO THE PRODUCT AND IS IN LIEU OF AND EXCLUDES ALL
OTHER WARRANTIES OF ANY NATURE WHATSOEVER, WHETHER EXPRESS,
IMPLIED OR ARISING BY OPERATION OF LAW, INCLUDING, BUT NOT LIMITED
TO ANY IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A
PARTICULAR PURPOSE. THIS WARRANTY DOES NOT COVER OR PROVIDE FOR
THE REIMBURSEMENT OR PAYMENT OF INCIDENTAL OR CONSEQUENTIAL
DAMAGES. Some states do not allow this exclusion or limitation of incidental or
consequential damages so the above limitation or exclusion may not apply to you.
LEGAL REMEDIES: This warranty gives you specific legal rights, and you may also
have other rights which vary from state to state. This warranty is void outside the United
States of America.
PROCEDURE FOR OBTAINING PERFORMANCE OF WARRANTY: If, after following
the instructions in the owner’s manual you are certain that the Product is defective,
pack the Product carefully (preferably in its original packaging). The Product should
include all parts and accessories originally packaged with the Product. Include
evidence of original purchase and a note describing the defect that has caused you
to return it. The product should be shipped freight prepaid, by traceable means, to
warrantor at:
Uniden America Service
743 Henrietta Creek Rd.
Roanoke, TX 76262
(800) 297-1023, 8 a.m. to 5 p.m., Central, Monday through Friday


---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.4
Linearized                      : Yes
Create Date                     : 2014:02:12 12:04:38-06:00
Creator                         : Adobe InDesign CS4 (6.0.6)
Modify Date                     : 2014:03:21 13:41:12-07:00
XMP Toolkit                     : Adobe XMP Core 4.2.1-c041 52.342996, 2008/05/07-20:48:00
Instance ID                     : uuid:f768a0a0-4ea6-4784-b258-34c0d5ca8bad
Document ID                     : xmp.did:CAEC87CD0394E311B87CD0A7CF862D68
Original Document ID            : adobe:docid:indd:a05d1790-00e4-11dd-a005-f7b58bdb6f3b
Rendition Class                 : proof:pdf
Derived From Instance ID        : xmp.iid:C9EC87CD0394E311B87CD0A7CF862D68
Derived From Document ID        : xmp.did:B8426949448FE31190C2E7268A12636C
Derived From Original Document ID: adobe:docid:indd:a05d1790-00e4-11dd-a005-f7b58bdb6f3b
Derived From Rendition Class    : default
History Action                  : saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved
History Instance ID             : xmp.iid:4AC8E8185E74E211B4AC900E92FA1C08, xmp.iid:4BC8E8185E74E211B4AC900E92FA1C08, xmp.iid:70EB36519077E211A84DE183C084A424, xmp.iid:037F0D9F947BE21183EBB96F5157C0CB, xmp.iid:4F4CD395457CE21198A6DABD3A754A15, xmp.iid:433CEE37FE84E211B43CA9C5DD9E5F3A, xmp.iid:774230C487FBE2118AD0A7A9B495863C, xmp.iid:784230C487FBE2118AD0A7A9B495863C, xmp.iid:794230C487FBE2118AD0A7A9B495863C, xmp.iid:955E71E6DBFDE2119CE89D33A1B97892, xmp.iid:985E71E6DBFDE2119CE89D33A1B97892, xmp.iid:D022138C3B25E3118598F51ACA267AD1, xmp.iid:D122138C3B25E3118598F51ACA267AD1, xmp.iid:306E8699AF2AE311A4DF86A7263510A8, xmp.iid:668D8DC3B12AE311A4DF86A7263510A8, xmp.iid:678D8DC3B12AE311A4DF86A7263510A8, xmp.iid:009742294C85E31180AC8603F7324CFF, xmp.iid:019742294C85E31180AC8603F7324CFF, xmp.iid:FB9D26A0A187E311958CEA0861557475, xmp.iid:01729C245488E311AFF1B213BEC758B4, xmp.iid:37BA7E63BD8AE3119AA3D1723D0BBF97, xmp.iid:9D6CD8ACEE8CE311963AAE5154BEA4F7, xmp.iid:D8BCF377B18DE311809EBF8B5B7D3499, xmp.iid:B6426949448FE31190C2E7268A12636C, xmp.iid:B7426949448FE31190C2E7268A12636C, xmp.iid:B8426949448FE31190C2E7268A12636C, xmp.iid:3BE410F5798FE31188D7EAF5FC07EEC1, xmp.iid:C3C39D283390E3118CAE818A5CE8D46C, xmp.iid:C4C39D283390E3118CAE818A5CE8D46C, xmp.iid:A212FDD37292E311A12BFA6B1E30BDC9, xmp.iid:C9EC87CD0394E311B87CD0A7CF862D68, xmp.iid:CAEC87CD0394E311B87CD0A7CF862D68
History When                    : 2013:02:11 10:01-06:00, 2013:02:11 10:01-06:00, 2013:02:15 10:54:09-06:00, 2013:02:20 13:35:02-06:00, 2013:02:21 10:41:48-06:00, 2013:03:04 15:42:50-06:00, 2013:08:02 12:03:06-05:00, 2013:08:02 12:03:45-05:00, 2013:08:02 12:03:45-05:00, 2013:08:05 11:07:27-05:00, 2013:08:05 11:12:14-05:00, 2013:09:24 15:55:39-05:00, 2013:09:24 15:55:39-05:00, 2013:10:01 10:54:16-05:00, 2013:10:01 10:54:32-05:00, 2013:10:01 10:54:33-05:00, 2014:01:24 17:06:30-06:00, 2014:01:24 17:06:30-06:00, 2014:01:27 16:23:19-06:00, 2014:01:28 13:41:12-06:00, 2014:01:31 15:19:37-06:00, 2014:02:03 11:09:30-06:00, 2014:02:04 09:31:51-06:00, 2014:02:06 09:35:20-06:00, 2014:02:06 09:42:04-06:00, 2014:02:06 09:42:05-06:00, 2014:02:06 15:59:31-06:00, 2014:02:07 14:05:15-06:00, 2014:02:07 14:15:09-06:00, 2014:02:10 10:46:03-06:00, 2014:02:12 10:36:20-06:00, 2014:02:12 10:36:20-06:00
History Software Agent          : Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0
History Changed                 : /, /metadata, /, /, /, /, /, /metadata, /, /, /, /metadata, /;/metadata, /, /metadata, /, /metadata, /;/metadata, /, /, /, /, /, /, /metadata, /, /, /, /, /, /metadata, /
Manifest Link Form              : ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream
Manifest Placed X Resolution    : 304.00, 72.00, 72.00, 72.00, 72.00, 72.00
Manifest Placed Y Resolution    : 304.00, 72.00, 72.00, 72.00, 72.00, 72.00
Manifest Placed Resolution Unit : Inches, Inches, Inches, Inches, Inches, Inches
Manifest Reference Instance ID  : uuid:15BAF1D6BFF9DC119499A9AB27D7C261, xmp.iid:4C5F52EC6C92E3118261E2FD44C76188, uuid:94f25236-87ff-472a-aa4c-a653bf171ff0, xmp.iid:4D5F52EC6C92E3118261E2FD44C76188, uuid:54b6a082-2858-4f1b-b1a8-3d9c9b041354, uuid:6d202e02-dade-407a-b400-ccf7f77c05eb
Manifest Reference Document ID  : uuid:14BAF1D6BFF9DC119499A9AB27D7C261, xmp.did:4B5F52EC6C92E3118261E2FD44C76188, xmp.did:87166BF76C7DE3119066EC5B7DAFD38D, xmp.did:4B5F52EC6C92E3118261E2FD44C76188, uuid:AB8AC0DECBD8DC11BBACE1CB50D586D5, xmp.did:87166BF76C7DE3119066EC5B7DAFD38D
Metadata Date                   : 2014:03:21 13:41:12-07:00
Creator Tool                    : Adobe InDesign CS4 (6.0.6)
Thumbnail Format                : JPEG
Thumbnail Width                 : 256
Thumbnail Height                : 256
Thumbnail Image                 : (Binary data 6707 bytes, use -b option to extract)
Doc Change Count                : 4400
Format                          : application/pdf
Producer                        : Adobe PDF Library 9.0
Trapped                         : False
Page Count                      : 12

EXIF Metadata provided by EXIF.tools