Unitech Electronics MS340BT BT CCD Scanner User Manual

Unitech Electronics Co., Ltd. BT CCD Scanner

User Manual

Download: Unitech Electronics MS340BT BT CCD Scanner User Manual
Mirror Download [FCC.gov]Unitech Electronics MS340BT BT CCD Scanner User Manual
Document ID2936939
Application IDFGAyfHiubcYP84jr8fQdYg==
Document DescriptionUser Manual
Short Term ConfidentialNo
Permanent ConfidentialNo
SupercedeNo
Document TypeUser Manual
Display FormatAdobe Acrobat PDF - pdf
Filesize118.89kB (1486081 bits)
Date Submitted2016-03-21 00:00:00
Date Available2016-03-22 00:00:00
Creation Date2016-01-22 16:45:04
Producing SoftwareAcrobat Distiller 10.1.1 (Windows)
Document Lastmod2016-03-11 13:08:53
Document TitleUser Manual
Document Author: user

BT CCD Scanner
- FCC ID: HLEMS340BT -
sUser's Manual
Version 1.1
© 2016 unitech Electronics Co., Ltd. All rights reserved.
unitech is a registered trademark of unitech Electronics Co., Ltd
Change Log.
Date
Change Description
Version
2016/1/11
first published version
1.0
2016/1/22
Add 1.4.2 Installing the battery
1.1
© 2016 unitech Electronics Co., Ltd. All rights reserved.
unitech is a registered trademark of unitech Electronics Co., Ltd
Preface
About This Manual
Thank you for purchasing the unitech product.
This manual explains how to install, operate and maintain our product.
No part of this publication may be reproduced or used in any form, or by any
electrical or mechanical means, such as photocopying, recording, or
information storage and retrieval systems, without permission in writing from
the manufacturer. The material in this manual is subject to change without
notice.
Regulatory Compliance Statements
FCC Warning Statements
This device has been tested and found to comply with the limits for a Class B
digital device, pursuant to part 15 of the FCC rules. These limits are designed
to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may
cause harmful interference with radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this
equipment does cause harmful interference with radio or television reception,
which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the following
measures:
–Reorient or relocate the receiving antenna.
–Increase the separation between the equipment and receiver.
–Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
–Consult the dealer or an experienced radio/TV technician for help.
© 2016 unitech Electronics Co., Ltd. All rights reserved.
unitech is a registered trademark of unitech Electronics Co., Ltd.
1.
2.
3.
This transmitter must not be co-located or operating in conjunction with
any other antenna or transmitter.
This device complies with FCC RF radiation exposure limits set forth for
an uncontrolled environment. To maintain compliance with FCC RF
exposure requirements, avoid direct contact to the transmitting antenna
during transmitting.
Any changes or modifications (including the antennas) made to this
device that are not expressly approved by the manufacturer may void the
user’s authority to operate the equipment.
FCC Label Statement
This device complies with part 15 of the FCC rules. Operation is subject to the
following two conditions:
1. This device may not cause harmful interference, and
2. This device must accept any interference received, including interference
that may cause undesired operation.
Canadian Compliance Statement
This Class B Digital apparatus meets all requirements of the Canadian
Interference-Causing Equipment Regulations.
Cet appareil numerique de la classe B respecte les exigences du Reglement
sur le material broilleur du Canada.
ii
© 2016 unitech Electronics Co., Ltd. All rights reserved.
unitech is a registered trademark of unitech Electronics Co.,Ltd
European Conformity Statement
unitech Electronics co., Ltd herewith declares that the unitech product is in
compliance with the essential requirements and all other provisions of the
R&TTE 1999/5/EC directive, the EMC 2004/108/EC directive and the Low
Voltage 2006/95/EC directive.
The declaration of conformity is available for download at :
https://portal.unitech.eu/public/Safetyregulatorystatement
RoHS Statement
This device conforms to RoHS (Restriction of
Hazardous Substances) European Union regulations
that set maximum concentration limits on hazardous
materials used in electrical and electronic
equipment.
Waste electrical and electronic equipment (WEEE)
unitech has set up a policy and process to meet the EU
directive 2002/96/EC and update 2003/108/EC
concerning electronic waste disposal.
For more detailed information of the electronic waste
disposal of the products you have purchased from
unitech directly or via unitech’s resellers, you shall either
contact your local supplier or visit us at :
https://portal.unitech.eu/public/WEEE
iii
© 2016 unitech Electronics Co., Ltd. All rights reserved.
unitech is a registered trademark of unitech Electronics Co., Ltd.
Taiwan NCC Warning Statement
交通部電信總局低功率電波輻射性電機管理辦法
第十二條：經型式認證合格之低功率射頻電機，非經許可，公司、商號或使用者
均不得擅自變更頻率、加大功率或變更原設計之特性及功能。
第十四條：低功率射頻電機之使用不得影響飛航安全及干擾合法通信；經發現有
干擾現象時，應立即停用，並改善至無干擾時方得繼續使用。
低功率射頻電機需忍受合法通信或工業、科學及醫療用電波輻射性電機設備
之干擾。
注意事項:
1. 使用過度恐傷害視力。
2. 使用30分鐘請休息10分鐘；2歲以下幼兒不看螢幕，2歲以上每天看螢幕不要超過
1小時。
iv
© 2016 unitech Electronics Co., Ltd. All rights reserved.
unitech is a registered trademark of unitech Electronics Co., Ltd.
Laser Information
The unitech product is certified in the U.S. to conform to the requirements of
DHHS/CDRH 21CFR Subchapter J and to the requirements of IEC 825-1.
Class II and Class 2 products are not considered to be hazardous. The unitech
product contains internally a Visible Laser Diode (VLD) whose emissions do
not exceed the maximum limits as set forth in the above regulations. The
scanner is designed so that there is no human access to harmful laser light
during normal operation, user maintenance or prescribed service operations.
The laser safety warning label required by the DHHS/IEC for the unitech
product’s optional laser scanner module is located on the memory
compartment cover, on the back of the unit.
* Laser information only applies to the products with laser components.
CAUTION! Use of controls or adjustments or performance of procedures
other than those specified herein may result in hazardous laser
light. Use of optical instruments with the scanner, including
binoculars, microscopes, and magnifying glasses, with will
increase eye damage. This does not include eyeglasses worn by
the user.
LED Information
The unitech product contains LED indicator(s) or LED ring whose luminance is
not harmful to human eyes during normal operation, user maintenance or
prescribed service operations.
*LED information only applies to the products with LED components.
© 2016 unitech Electronics Co., Ltd. All rights reserved.
unitech is a registered trademark of unitech Electronics Co., Ltd.
Battery Notice
1.
To guarantee optimal performance, it is recommended that rechargeable
batteries be replaced every year, or after 500 charging cycles are
completed. It is normal for the battery to balloon or expand after one year
or 500 cycles. Although it does not cause damage, it cannot be used
again and must be disposed of according to the location's safe battery
disposal procedures.
2.
If a battery performance decreases more than 20%, the battery is at the
end of its life cycle. Stop use and ensure the battery is disposed of
properly.
3.
The length of time that a battery lasts depends on the battery type and
how the device is used. Conserve the battery life by doing the following:
 Avoid fully uncharging the battery because this places additional
4.
5.
6.
7.
strain on it. Several partial uncharges with frequent charges are better
than a fully uncharged battery. Charging a partially charged battery
does not cause harm to the unit.
 Keep the battery cool. Avoid hot vehicles. For prolonged
storage, keep the battery at a 40% charge level.
 Do not leave the battery uncharged and unused for an extended
period of time, the battery will wear out and the longevity of the
battery will be at least half of one with frequent charges.
Protect battery life by not over or under charging the battery.
Please do not leave battery unused for long time without charging it.
Despite unitech’s safety precautions, the battery pack may begin to
change shape. If so, stop using it immediately. Please check to see if you
are using a proper power adapter to charge the battery or contact your
service provider for service.
If you cannot charge the battery after it has been idle for an extended
period of time and it begins to heat up, please do not try to charge it. It
may not be functional anymore.
Please only use the original battery from unitech. Using a third party
battery can damage our products. Please note that when such damage
occurs, it is not covered by unitech’s warranty policy
vi
© 2016 unitech Electronics Co., Ltd. All rights reserved.
unitech is a registered trademark of unitech Electronics Co., Ltd.
CAUTION!



RISK OF EXPLOSION IF BATTERY IS
REPLACED INCORRECTLY.
DISPOSE OF USED BATTERIES ACCORDING
TO THE INSTRUCTIONS..
如果更換不正確之電池行事會有爆炸的風險
請依製造商說明書處理用過之電池
如果更换不正确之电池行事会有爆炸的风险
请依制造商说明书处理用过之电池
Battery charge notice
It is important to consider temperature when the battery pack is charging.
Charging is most efficient at normal room temperature or in a slightly cooler
environment. It is essential that batteries are charged within the stated range of
0°C to 40°C. Charging batteries outside of the specified range could damage
the batteries and shorten their life cycle.
CAUTION!
Do not charge batteries at a temperature lower than 0°C. This will
and make the batteries unstable and dangerous. Please use a
battery temperature detecting device for a charger to ensure a
safe charging temperature range.
Storage and safety notice
Although charged batteries may be left unused for several months, their
capacity may be depleted due to build up of internal resistance. If this happens,
they will require recharging prior to use. Batteries may be stored at
temperatures between -20°C to 60°C, however they may deplete more rapidly
at higher temperatures. It is recommended to store batteries at room
temperature.
* The message above only applies to the usage of the removable batteries.
For the products with non-removable batteries / without batteries, please refer to
the specification of each product.
Product Operation and Storage Notice
The unitech product has applicable operation and storage temperature
conditions. Please follow the limitation of suggested temperature conditions to
avoid failure, damage or malfunction.
*For applicable temperature conditions, please refer to the specification of each
product.
vii
© 2016 unitech Electronics Co., Ltd. All rights reserved.
unitech is a registered trademark of unitech Electronics Co., Ltd.
Adapter Notice
1.
2.
3.
4.
Please do not leave the power adapter in the socket when it is not
connected to your unitech product for charging.
Please remove the power adapter when the battery is fully recharged.
The bundled power adapter that comes with your unitech product is not
meant to be used outdoors. An adapter exposed to water or rain, or a very
humid environment can cause damage to both the adapter and the
product.
Please only use the bundled power adapter or same specification of
adapter to charge your unitech product. Using the wrong power adapter
can damage your unitech product.
* The message above only applies to the product connected to the adapter.
For the products without using the adapters, please refer to the specification of
each product.
Hearing Damage Warning
Zx.3 Warning
The warning shall be placed on the equipment, or on the packaging, or in the instruction manual and shall consist of
the following:
the symbol of Figure 1 with a minimum height of 5 mm; and
the following wording, or similar :
To prevent possible hearing damage, do not listen at high volume levels for long periods.
Alternatively, the entire warning may be given through the equipment display during use, when the user is asked to
acknowledge activation of the higher level.
viii
© 2016 unitech Electronics Co., Ltd. All rights reserved.
unitech is a registered trademark of unitech Electronics Co., Ltd.
Worldwide Support
unitech’s professional support team is available to quickly answer questions or
assist with technical-related issues. Should an equipment problem occur,
please contact the nearest unitech regional service representative.
For complete contact information please visit the Web sites listed below:
Taipei, Taiwan – Headquarters
Europe
Tel:
+886-2-89121122
Tel:
+31-13-4609292
E-mail:
info@hq.ute.com
E-mail:
info@eu.ute.com
Address:
5F, No. 136, Lane 235, Baoqiao Road, Xindian
Address:
Tilburg, the Netherlands
District, New Taipei City 231, Taiwan (R.O.C.)
Website:
Kapitein Hatterasstraat 19, 5015 BB,
Website:
http://www.ute.com
China
http://eu.ute.com
Japan
Tel:
E-mail:
Address:
Website:
+86-59-2310-9966
info@cn.ute.com
Room401C, 4F, RIHUA International Mansion,
E-mail:
+81-3-35232766
E-mail:
info@jp.ute.com
Address:
Shinkawa, Chuo-Ku,
Xiamen, Fujan , China
Tokyo, 104-0033, Japan
http://cn.ute.com
Website:
http://jp.ute.com
Latin America
+886-2-27911556
Tel:
+52-55-5171-0528
info@apac.ute.com
E-mail:
info@latin.ute.com
info@india.ute.com
Address:
info@mideast.ute.com
Address:
Kayabacho Nagaoka Building 8F.,1-5-19
Xinfeng 3nd Road, Huoju Hi-tech District,
Asia & Pacific / Middle East
Tel:
Tel:
17171 Park Row, Suite 210
Houston, TX 77084USA (Rep.)
4F., No. 236, ShinHu 2nd Rd.,
Website:
http://latin.ute.com
NeiHu Chiu, 114, Taipei,Taiwan
Website:
http://apac.ute.com / http://mideast.ute.com
North America
Tel:
E-mail:
+1-714-8916400
info@us.ute.com / info@can.ute.com
Address:
6182 Katella Ave, Cypress, CA 90630, USA
Website:
http://us.ute.com / http://can.ute.com
ix
© 2016 unitech Electronics Co., Ltd. All rights reserved.
unitech is a registered trademark of unitech Electronics Co., Ltd.
Warranty Policy
The items covered under the unitech Limited Warranty are free from defects
during normal use.
The warranty period is varied from each country. Please consult with your
supplier or unitech local office for actual length of warranty period to your
purchased product.
Warranty becomes void if equipment is modified, improperly installed or used,
damaged by accident or neglect, or if any parts are improperly installed or
replaced by the user.
© 2016 unitech Electronics Co., Ltd. All rights reserved.
unitech is a registered trademark of unitech Electronics Co., Ltd.
Table of Contents
Preface...........................................................................................................i
About This Manual ........................................................................................ i
Regulatory Compliance Statements .............................................................. i
Laser Information ......................................................................................... v
LED Information ........................................................................................... v
Battery Notice.............................................................................................. vi
Adapter Notice............................................................................................viii
Hearing Damage Warning ..........................................................................viii
Worldwide Support ...................................................................................... ix
Warranty Policy ............................................................................................ x
Chapter 1 - Overview................................................................................1
1.1 Package .................................................................................................1
1.2 Scanner & Cradle Detail .........................................................................2
1.3 Specifications .........................................................................................3
1.4 Getting Started .......................................................................................6
1.5 Battery Charging ..................................................................................10
1.6 LED Indicator / Beeper Sequence ........................................................ 11
Chapter 2 – Configuration-General ....................................................13
2.1 Flow Chart ............................................................................................13
2.2 Loop of Programming...........................................................................14
2.3 Factory Default Settings .......................................................................14
2.4 Main Page of Configuration ..................................................................15
Chapter 3 –Bar Codes & Others..........................................................16
3.1 SymboIogies Selection.........................................................................16
3.2 UPC/EAN/JAN Parameters ..................................................................18
3.3 Code 39 Parameters ............................................................................20
3.4 Code 128 Parameters ..........................................................................21
3.5 Interleave 25 Parameters .....................................................................22
3.6 Industrial 25 Parameters ......................................................................23
3.7 Matrix 25 Parameters ...........................................................................24
3.8 CODABAR/NW7 Parameters ...............................................................25
3.9 Code 93 Parameters ............................................................................27
3.10 Code 11 Parameters...........................................................................28
xi
© 2016 unitech Electronics Co., Ltd. All rights reserved.
unitech is a registered trademark of unitech Electronics Co., Ltd.
3.11 MSI/PLESSEY Code Parameters .......................................................29
3.12 Code 2 of 6 Parameters .....................................................................30
3.13 LCD25 Parameters.............................................................................31
3.14 Telepen Parameters ...........................................................................32
3.15 GS1 Databar ......................................................................................33
3.16 Bar Code ID........................................................................................34
Chapter 4 – Command Setting.............................................................37
4.1 Interface & Reading Mode Selection ....................................................37
4.2 Communication Parameters .................................................................39
4.3 Language Selection..............................................................................42
4.4 Reading Level ......................................................................................43
4.5 Accuracy...............................................................................................44
4.6 Buzzer Beep Tone ................................................................................44
4.7 Sensitivity of Continuous Reading Mode ..............................................45
4.8 Reverse Output Characters..................................................................46
4.9 Setup Deletion......................................................................................46
4.10 Setup Insertion ...................................................................................49
4.11 PAN Configuration ..............................................................................52
Appendix
Appendix
Appendix
Appendix
A –Numeric Bar Codes........................................................55
B –ASCII Table.......................................................................56
C –Function Key Table........................................................60
D–Numeric Bar Codes2.......................................................61
xii
© 2016 unitech Electronics Co., Ltd. All rights reserved.
unitech is a registered trademark of unitech Electronics Co., Ltd.
Chapter 1 - Overview
1.1 Package
Please make sure the following contents are in the MS340B gift box.
If something is missing or damaged, please contact your unitech
representative.
The standard package contents:

MS340B Scanner

Quick Start Guide

Regulatory Compliance Statements

Cable

Cradle

Adapter
Note: To scan a barcode, make sure the aiming beam crosses every bar and
space of the barcode.
© 2016 unitech Electronics Co., Ltd. All rights reserved.
unitech is a registered trademark of unitech Electronics Co., Ltd.
1.2 Scanner & Cradle Detail
Scanner LED indicator
Scan Window
Trigger
Cradle
Cradle LED indicator
Cable connector
© 2016 unitech Electronics Co., Ltd. All rights reserved.
unitech is a registered trademark of unitech Electronics Co.,Ltd
1.3 Specifications
Optical & Performance
Sensor
Linear Imager
Visual Indicators
Beep and LED (Good read Green)
System Interface
USB
Light Source
635 nm Visible Red LED
Max. Resolution
4mil (0.1mm) PCS90%, Code39
Scan Rate
Up to 500 scans/second
Skew Angle
±60° (±5°)
Pitch Angle
±10°~65° (±5°)
Printing Contrast Scale
minimum 30%
Decoding
Supports most standard 1D bar code, GS1 Databar
linear and stacked Codes
Depth of Field
(DOF Code39
PCS=90% )
Communication
Radio Frequency
Bluetooth V2.1 EDR, (smaller 10mW)
Frequency Band
2.402GHz~2.480 GHz
Transmission Range
Up to 100m (328.08 FT.) line of sight
© 2016 unitech Electronics Co., Ltd. All rights reserved.
unitech is a registered trademark of unitech Electronics Co.,Ltd
Mechanical
Dimensions
72 x 70 x 164 mm (length x width x height)
Weight
174g (Scanner only)
Switch life
1,000,000 times
Electrical
Input Voltage
5VDC
Operating Power
<200mA
Standby Power
< 60mA
Battery
Li-ion 3.7V/2600 mAh
Charging time
Approx. 5 hours
Reads per charge
50,000 times
Environmental
Light Levels
Max 100,000 Lux
Mechanical Shock
1.5m onto concrete (scanner only)
IP Rate
IP42
Operating
Temperature
0°C to 50°C
Storage Temperature -20°C to 70°C
Relative Humidity
20% to 95% non-condensing
Regulation Approvals
CE, FCC, BSMI, VCCI, NCC, TELEC
© 2016 unitech Electronics Co., Ltd. All rights reserved.
unitech is a registered trademark of unitech Electronics Co.,Ltd
Readable Symbologies
© 2016 unitech Electronics Co., Ltd. All rights reserved.
unitech is a registered trademark of unitech Electronics Co.,Ltd
1.4 Getting Started
Please scan below barcode to set default for BT parameter.
For configuration, please refer to 2.1 Flow Chart.
BT Parameter Set Default
1.4.1 Scanner Mode
There are three different scanner modes. Please follow the instructions below.
A. Setup SPP Master Mode* (Default option)
SPP Master Mode*
Please follow the below steps to setup the communication between the scanner and cradle.
1) The scanner must scan “SPP Master Mode” barcode to set the scanner in master mode.
2) Scan the BT MAC address code located on the bottom of the cradle.
3) When the BT MAC address code was successfully scanned, scanner will sound 3 short
beeps with green LED flash once.
4) Wait approximately five seconds for completing the connection process with up-tone.
5) If successful, blue LED of scanner will slow flash and the cradle will be continued on.
B. Setup SPP Slave Mode
SPP Slave Mode
Please follow the below steps to setup the communication between the scanner and BT
application device.
1) The scanner must scan “SPP Slave Mode” barcode, to set the scanner in slave mode.
2) When control the BT device to search the scanner, enter pin code (default 00:00:00) to
setup comport.
3) When scanner is successful connected, the scanner blue LED will also blink with up-tone.
Blue LED will slowly flash to finish the setup.
© 2016 unitech Electronics Co., Ltd. All rights reserved.
unitech is a registered trademark of unitech Electronics Co.,Ltd
C. Setup HID Slave Mode
HID Slave Mode
Please follow the steps to setup the communication between the scanner and Bluetooth HID
profile application device.
1)
2)
3)
The scanner must scan “HID Slave Mode” barcode to set the scanner in HID slave mode.
When control the BT device to search the scanner, enter pin code (default 00:00:00) to
setup pairing. You can scan number barcode on Appendix D, “Numeric Bar Codes 2 ”
number 0~9, to setup.
When scanner is successful connected, scanner blue LED will also blink with up-tone.
Blue LED will slowly flash to finish the setup.
© 2016 unitech Electronics Co., Ltd. All rights reserved.
unitech is a registered trademark of unitech Electronics Co.,Ltd
1.4.2 Installing battery
To install the scanner battery, please follow the instructions below.
1. Use screwdriver to loosen the
screw on the bottom of the scanner
and remove the battery cover.
2. Slide and position the battery, make
sure the battery contacts are aligned
with the contacts in the scanner.
3. Replace the battery cover and use the screwdriver to tighten the screw on the bottom
of the scanner.
© 2016 unitech Electronics Co., Ltd. All rights reserved.
unitech is a registered trademark of unitech Electronics Co.,Ltd
1.4.3 Switching Cable
Before removing the cable from the cradle, it is recommended that
the power on the host system is off and the power supply has been
disconnected from the unit.
1. Find the small "Pin-hole" on the bottom of the cradle. (Please see the photo as below)
2. Use a bended regular paperclip and insert the tip into the hole.
3. You will hear a "click", then gently pull out the strain-relief of the cable.
Pin-hole
© 2016 unitech Electronics Co., Ltd. All rights reserved.
unitech is a registered trademark of unitech Electronics Co.,Ltd
1.5 Battery Charging
The battery is in advance loaded into the compartment of the scanner and may
not be fully charged before shipment. When you receive the package and use
the MS340B for the first time, you will need to fully charge the battery.
It takes approximately 5 hours to fully charge the battery.
To chage the scanner with a cradle, please follow the instructions below.
1. Plug the adapter cable into the power socket on the
bottom of cradle.
2. Plug the AC adapter cord into an electrical outlet.
3. Place the scanner in the cradle. The scanner LED
will be red to indicate charging and turn green
when it is fully charged.
Scanner LED
indicator
10
© 2016 unitech Electronics Co., Ltd. All rights reserved.
unitech is a registered trademark of unitech Electronics Co.,Ltd
1.6 LED Indicator / Beeper Sequence
￭
Scanner LED Status
LED for Barcode
reading &
Communication
Action/Status
Good read and transmitted
Good read and save on
Beep Tone
Green light blinks once One beep
Green light blinks once One beep
memory (BT disconnect)
Good Read but Transmit Fail
Green light blinks twice Two beeps
Battery fully charged
Solid green light
No action
Memory full
Red light blinks twice
Two beeps
Red light blinks once
Low Battery warning
every 20 seconds
In charging
Solid red light
Blue light blinks twice
BT disconnect
One beep
No action
No action
(continuously)
BT disconnect
No action
before sleep
Blue light blinks once
BT connected
every two seconds
Setting ok
Green light blinks once
Start charging
Solid red light
Blue light blinks once
Battery changed
Low beep
High beep
No action
No action
No action
then green light blinks
twice
11
© 2016 unitech Electronics Co., Ltd. All rights reserved.
unitech is a registered trademark of unitech Electronics Co.,Ltd
￭ Cradle LED Status
Action/Status
Good read and transmitted
LED for Barcode
reading &
Communication
Green light blinks once
BT disconnect (continuously) Blue light blinks twice
BT connected
Solid blue light
12
© 2016 unitech Electronics Co., Ltd. All rights reserved.
unitech is a registered trademark of unitech Electronics Co.,Ltd
Chapter 2 – Configuration-General
2.1 Flow Chart
*Please scan the following barcodes for configuration
Start Configuration
End Configuration
Abort Configuration
Save Parameters
13
© 2016 unitech Electronics Co., Ltd. All rights reserved.
unitech is a registered trademark of unitech Electronics Co.,Ltd
2.2 Loop of Programming
The philosophy of programming parameters has been shown on the flow chart
of 2.1. Basically user should :
1.
2.
3.
4.
5.
Scan Start of Configuration.
Scan all necessary labels for parameters that meet applications.
Scan End of Configuration to end the programming.
To permanently save the settings you programmed, just scan label for
Save Parameters.
To go back to the Default Settings, just scan label for Set All Defaults.
( Please refer to 2.4 – Main Page of Configuration)
2.3 Factory Default Settings
The barcode with an asterisk (*) which appears in the following chapters
indicates that it is the default option for the corresponding setting.
The barcode with two asterisks (**) indicate that it is the quick setting
label.
You can make your own settings by following the procedures in this manual. If
you want to save the settings permanently, you should scan the label of “Save
Parameters” in chapter 2.4, otherwise the settings will not be saved after the
decoder power is off, and all settings will go back to previous settings.
By scanning “Set All Default” label, the settings will go back to the factory
default settings. ( Please refer to 2.4 – Main Page of Configuration)
14
© 2016 unitech Electronics Co., Ltd. All rights reserved.
unitech is a registered trademark of unitech Electronics Co.,Ltd
2.4 Main Page of Configuration
Save Parameters
Recall Stored Parameters
Set All Defaults**
Start Configuration
End Configuration
Abort Configuration
Version Information**
** : Quick Setting Label
Save Parameters -The parameter settings will be saved permanently.
Recall Stored Parameters - Replace the current parameters by the
parameters you saved last time.
Set AII Defaults - Set all the parameters to the factory default settings.
Abort Configuration - Terminate current programming status.
Version Information - Display the decoder version information and date code.
15
© 2016 unitech Electronics Co., Ltd. All rights reserved.
unitech is a registered trademark of unitech Electronics Co.,Ltd
Chapter 3 –Bar Codes & Others
3.1 SymboIogies Selection
UPC-A ON *
UPC-A OFF
Industrial 25 ON
Industrial 25 OFF *
UPC-E ON *
UPC-E OFF
Matrix 25 ON
Matrix 25 OFF *
EAN-13/JAN-13/ISBN-13
ON *
EAN-13/JAN-13/ISBN-13
EAN-8/JAN-8 ON *
EAN-8/JAN-8 OFF
CODE 39 ON *
CODE 39 OFF
CODE 128 ON *
CODE 128 OFF
CODABAR/NW7 ON *
Interleave 25 ON *
CODE 93 ON
CODE 93 OFF *
OFF
CODE 11 ON
CODABAR/NW7 OFF
Interleave 25 OFF
CODE 11 OFF *
China Postage ON
China Postage OFF *
MSI/PLESSEY ON
MSI/PLESSEY OFF *
Code 2 of 6 ON
LCD25 ON
Code 2 of 6 OFF *
LCD25 OFF *
16
© 2016 unitech Electronics Co., Ltd. All rights reserved.
unitech is a registered trademark of unitech Electronics Co.,Ltd
Telepen ON
Reserved5 ON
Telepen OFF *
Reserved5 OFF *
GS1 DataBar
GS1 DataBar Omnidirectional
Omnidirectional ON
OFF *
GS1 DataBar Limited
GS1 DataBar Limited OFF *
ON
Reserved6 ON
Reserved6 OFF *
GS1 DataBar
GS1 DataBar Expanded OFF *
Expanded ON
Select All Bar Codes
17
© 2016 unitech Electronics Co., Ltd. All rights reserved.
unitech is a registered trademark of unitech Electronics Co.,Ltd
3.2 UPC/EAN/JAN Parameters
A. Reading Type
UPCA=EAN13 ON
ISBN-10 Enable
B. Supplemental Set Up
UPCA=EAN13 OFF *
ISBN-13 Enable *
ISSN Enable
ISSN Disable *
Decode with
Supplement
Auto discriminate
Not Transmit *
Transmit 2 Code
Transmit 5 Code
Transmit 2&5 Code
Supplement *
Expand UPC-E
Enable
Expand UPC-E Disable *
EAN8=EAN13
EAN8=EAN13 Disable *
Enable
GTIN Format
GTIN Format
Enable
Disable *
18
© 2016 unitech Electronics Co., Ltd. All rights reserved.
unitech is a registered trademark of unitech Electronics Co.,Ltd
C. Check Digit Transmission
UPC-A Check Digit Transmission ON *
UPC-A Check Digit Transmission OFF
UPC-E Check Digit Transmission ON *
UPC-E Check Digit Transmission OFF
EAN-8 Check DigitTransmission ON *
EAN-8 Check DigitTransmission OFF
EAN-13 Check Digit Transmission ON *
EAN-13 Check Digit Transmission OFF
ISSN Check Digit Transmission ON *
ISSN Check Digit Transmission OFF
19
© 2016 unitech Electronics Co., Ltd. All rights reserved.
unitech is a registered trademark of unitech Electronics Co.,Ltd
3.3 Code 39 Parameters
A. Type of Code
B. Check Digit Transmission
Italian Pharmacy/
Code 32 OFF *
Do Not Calculate Check Digit *
Disable *
Italian Pharmacy/
Code 32 ON
Calculate Check Digit & Transmit
Enable
Standard *
C. Output Start/Stop D. Decode Asterisk
Character
Disable *
Enable
Calculate Check Digit & Not Transmit
Full ASCII
E. Set Up Code Length
To set the fixed length:
1. Scan the “Begin“ label of the desired set.
2. Go to Numeric Bar Codes in Appendix A, scan label(s) that represents the length to be read.
3. Scan the “Complete“ label of the desired set. Repeat the steps 1 - 3 to set additional lengths.
Variable *
Fix Length (2 Sets Available)
1. 1st Set Begin
3.
2nd Set Begin
2. Numeric Bar
Codes (Appendix A)
2. Numeric Bar
Codes (Appendix A)
3.1st Set Complete
3. 2nd Set Complete
Minimum Length
1. Begin
2. Numeric Bar
Codes (Appendix A)
3. Complete
20
© 2016 unitech Electronics Co., Ltd. All rights reserved.
unitech is a registered trademark of unitech Electronics Co.,Ltd
3.4 Code 128 Parameters
A. Reading Type
B. Check Digit
Transmission
C. Append FNC2
UCC/EAN-128 Disable * UCC/EAN-128 Enable
Calculate Check
Digit& Not Transmit *
OFF*
Enable ‘]C1‘Code
Format *
Disable ‘]C1‘Code
Format
Calculate Check Digit
& Transmit
ON
Enable Code128
Group Separators(GS) *
Disable Code128
Group Separators(GS)
Do Not Calculate
Check Digit
D. Set Up Code Length
To set the fixed length:
1. Scan the “Begin“ label of the desired set.
2. Go to Numeric Bar Codes in Appendix A, scan label(s) that represents the length to be read.
3. Scan the “Complete“ label of the desired set. Repeat the steps 1 - 3 to set additional lengths.
Variable *
Fix Length (2 Sets Available)
1. 1st Set Begin
1. 2nd Set Begin
2. Numeric Bar
Codes (Appendix A)
2. Numeric Bar
Codes (Appendix A)
3. 1st Set Complete
3. 2nd Set Complete
Minimum Length
1. Begin
2. Numeric Bar
Codes (Appendix A)
3. Complete
21
© 2016 unitech Electronics Co., Ltd. All rights reserved.
unitech is a registered trademark of unitech Electronics Co.,Ltd
3.5 Interleave 25 Parameters
A. Check Digit
Transmission
B. Set Up Number of
Character
Do Not Calculate
Check Digit *
Calculate Check Digit &
Transmit
C. Brazilian Banking Code
Even *
Disable *
Odd
Enable
Calculate Check Digit &
Not Transmit
D. Set Up Code Length
To set the fixed length:
1. Scan the “Begin“ label of the desired set.
2. Go to Numeric Bar Codes in Appendix A, scan label(s) that represents the length to be read.
3. Scan the “Complete“ label of the desired set. Repeat the steps 1 - 3 to set additional lengths.
Variable *
Fix Length (2 Sets Available)
1. 1st Set Begin
1. 2nd Set Begin
2. Numeric Bar
Codes (Appendix A)
2. Numeric Bar
Codes (Appendix A)
3. 1st Set Complete
3. 2nd Set Complete
Minimum Length
1. Begin
2. Numeric Bar
Codes (Appendix A)
3. Complete
22
© 2016 unitech Electronics Co., Ltd. All rights reserved.
unitech is a registered trademark of unitech Electronics Co.,Ltd
3.6 Industrial 25 Parameters
A. Reading Type
B. Check Digit Transmission
IATA25 Disable *
Do Not Calculate Check Digit *
IATA25 Enable
Calculate Check Digit & Transmit
Calculate Check Digit & Not Transmit
C. Set Up Code Length
To set the fixed length:
1. Scan the “Begin“ label of the desired set.
2. Go to Numeric Bar Codes in Appendix A, scan label(s) that represents the length to be read.
3. Scan the “Complete“ label of the desired set. Repeat the steps 1 - 3 to set additional lengths.
Variable *
Fix Length (2 Sets Available)
1. 1st Set Begin
1. 2nd Set Begin
2. Numeric Bar
Codes (Appendix A)
2. Numeric Bar
Codes (Appendix A)
3. 1st Set Complete
3. 2nd Set Complete
Minimum Length
1. Begin
2. Numeric Bar
Codes (Appendix A)
3. Complete
23
© 2016 unitech Electronics Co., Ltd. All rights reserved.
unitech is a registered trademark of unitech Electronics Co.,Ltd
3.7 Matrix 25 Parameters
A. Check Digit Transmission
Do Not Calculate Check Digit *
Calculate Check Digit & Transmit
Calculate Check Digit & Not Transmit
B. Set Up Code Length
To set the fixed length:
1. Scan the “Begin“ label of the desired set.
2. Go to Numeric Bar Codes in Appendix A, scan label(s) that represents the length to be read.
3. Scan the “Complete“ label of the desired set. Repeat the steps 1 - 3 to set additional lengths.
Variable *
Fix Length (2 Sets Available)
1. 1ST Set Begin
1. 2nd Set Begin
2. Numeric Bar
Codes (Appendix A)
2. Numeric Bar
Codes (Appendix A)
3. 1ST Set Complete
3. 2nd Set Complete
Minimum Length
1. Begin
2. Numeric Bar
Codes (Appendix A)
3. Complete
24
© 2016 unitech Electronics Co., Ltd. All rights reserved.
unitech is a registered trademark of unitech Electronics Co.,Ltd
3.8 CODABAR/NW7 Parameters
A. Set Up Start/
Stop Characters Upon Transmission
B. Transmission Type of Start/Stop
OFF *
A/B/C/D Start *
ON
A/B/C/D Stop *
A Start
A Stop
B Start
B Stop
C Start
C Stop
D Start
D Stop
25
© 2016 unitech Electronics Co., Ltd. All rights reserved.
unitech is a registered trademark of unitech Electronics Co.,Ltd
C. Set Up Code Length
To set the fixed length:
1. Scan the “Begin“ label of the desired set.
2. Go to Numeric Bar Codes in Appendix A, scan label(s) that represents the length to be read.
3. Scan the “Complete“ label of the desired set. Repeat the steps 1 - 3 to set additional lengths.
Variable *
Fix Length (2 Sets Available)
1. 1st Set Begin
1. 2nd Set Begin
2. Numeric Bar
Codes (Appendix A)
2. Numeric Bar
Codes (Appendix A)
3. 1st Set Complete
3. 2nd Complete
Minimum Length
1. Begin
2. Numeric Bar
Codes (Appendix A)
3. Complete
26
© 2016 unitech Electronics Co., Ltd. All rights reserved.
unitech is a registered trademark of unitech Electronics Co.,Ltd
3.9 Code 93 Parameters
A. Check Digit Transmission
Calculate Check 2 Digits & Not Transmit *
Do Not Calculate Check Digit
B. Set Up Code Length
To set the fixed length:
1. Scan the “Begin“ label of the desired set.
2. Go to Numeric Bar Codes in Appendix A, scan label(s) that represents the length to be read.
3. Scan the “Complete“ label of the desired set. Repeat the steps 1 - 3 to set additional lengths.
Variable*
Fix Length (2 Sets Available)
1. 1st Set Begin
1. 2nd Set Begin
2. Numeric Bar
Codes (Appendix A)
2. Numeric Bar
Codes (Appendix A)
3. 1st Set Complete
3. 2nd Set Complete
Minimum Length
1. Begin
2. Numeric Bar
Codes (Appendix A)
3. Complete
27
© 2016 unitech Electronics Co., Ltd. All rights reserved.
unitech is a registered trademark of unitech Electronics Co.,Ltd
3.10 Code 11 Parameters
A. Check Digit Transmission
Do Not Calculate Check Digit *
Calculate Check 1
Digit & Transmit
Calculate Check 1
Digit & Not Transmit
Calculate Check 2
Digit & Transmit
Calculate Check 2
Digit & Not Transmit
B. Set Up Code Length
To set the fixed length:
1. Scan the “Begin“ label of the desired set.
2. Go to Numeric Bar Codes in Appendix A, scan label(s) that represents the length to be read.
3. Scan the “Complete“ label of the desired set. Repeat the steps 1 - 3 to set additional lengths.
Variable *
Fix Length (2 Sets Available)
1. 1st Set Begin
1. 2nd Set Begin
2. Numeric Bar
Codes (Appendix A)
2. Numeric Bar
Codes (Appendix A)
3. 1st Set Complete
3. 2nd Set Complete
Minimum Length
1. Begin
2. Numeric Bar
Codes (Appendix A)
3. Complete
28
© 2016 unitech Electronics Co., Ltd. All rights reserved.
unitech is a registered trademark of unitech Electronics Co.,Ltd
3.11 MSI/PLESSEY Code Parameters
A. Check Digit Transmission
Calculate Check Digit & Not Transmit *
Do Not Calculate Check Digit
Calculate Check Digit & Transmit
B. Set Up Code Length
To set the fixed length:
1. Scan the “Begin“ label of the desired set.
2. Go to Numeric Bar Codes in Appendix A, scan label(s) that represents the length to be read.
3. Scan the “Complete“ label of the desired set. Repeat the steps 1 - 3 to set additional lengths.
Variable *
Fix Length (2 Sets Available)
1. 1st Set Begin
1. 2nd Set Begin
2. Numeric Bar
Codes (Appendix A)
2. Numeric Bar
Codes (Appendix A)
3. 1st Set Complete
3. 2nd Set Complete
Minimum Length
1. Begin
2. Numeric Bar
Codes (Appendix A)
3. Complete
29
© 2016 unitech Electronics Co., Ltd. All rights reserved.
unitech is a registered trademark of unitech Electronics Co.,Ltd
3.12 Code 2 of 6 Parameters
A. Check Digit Transmission
Do Not Calculate Check Digit *
Calculate Check Digit & Transmit
Calculate Check Digit & Not Transmit
B. Set Up Code Length
To set the fixed length:
1. Scan the “Begin“ label of the desired set.
2. Go to Numeric Bar Codes in Appendix A, scan label(s) that represents the length to be read.
3. Scan the “Complete“ label of the desired set. Repeat the steps 1 - 3 to set additional lengths.
Variable *
Fix Length (2 Sets Available)
1.1st Set Begin
1. 2nd Set Begin
2. Numeric Bar
Codes (Appendix A)
2. Numeric Bar
Codes (Appendix A)
3. 1st Set Complete
3. 2nd Set Complete
Minimum Length
1. Begin
2. Numeric Bar
Codes (Appendix A)
3. Complete
30
© 2016 unitech Electronics Co., Ltd. All rights reserved.
unitech is a registered trademark of unitech Electronics Co.,Ltd
3.13 LCD25 Parameters
A. Check Digit Transmission
Do Not Calculate Check Digit *
Calculate Check Digit & Transmit
Calculate Check Digit & Not Transmit
B. Set Up Code Length
To set the fixed length:
1. Scan the “Begin“ label of the desired set.
2. Go to Numeric Bar Codes in Appendix A, scan label(s) that represents the length to be read.
3. Scan the “Complete“ label of the desired set. Repeat the steps 1 - 3 to set additional lengths.
Variable *
Fix Length (2 Sets Available)
1. 1st Set Begin
1. 2nd Set Begin
2. Numeric Bar
Codes (Appendix A)
2. Numeric Bar
Codes (Appendix A)
3. 1st Set Complete
3. 2nd Set Complete
Minimum Length
1. Begin
2. Numeric Bar
Codes (Appendix A)
3. Complete
31
© 2016 unitech Electronics Co., Ltd. All rights reserved.
unitech is a registered trademark of unitech Electronics Co.,Ltd
3.14 Telepen Parameters
A. Type of Code
B. Check Digit Transmission
Full ASCII Mode *
Calculate Check Digit & Not Transmit*
Compressed Numeric Mode
Do Not Calculate Check Digit
Calculate Check Digit & Transmit
C. Set Up Code Length
To set the fixed length:
1. Scan the “Begin“ label of the desired set.
2. Go to Numeric Bar Codes in Appendix A, scan label(s) that represents the length to be read.
3. Scan the “Complete“ label of the desired set. Repeat the steps 1 - 3 to set additional lengths.
Variable *
Fix Length (2 Sets Available)
1. 1st Set Begin
1. 2nd Set Begin
2. Numeric Bar
Codes (Appendix A)
2. Numeric Bar
Codes (Appendix A)
3. 1ST Set Complete
3. 2nd Set Complete
Minimum Length
1. Begin
2. Numeric Bar
Codes (Appendix A)
3. Complete
32
© 2016 unitech Electronics Co., Ltd. All rights reserved.
unitech is a registered trademark of unitech Electronics Co.,Ltd
3.15 GS1 Databar
A. GS1 DataBar Omnidirectional
B. GS1 DataBar Limited Parameters
Transmit Check Digit *
Don’t Transmit
Check Digit
Transmit Check
Digit *
Transmit
Application ID *
Don’t Transmit
Application ID
Transmit Application
ID*
Don’t Transmit
Symbology ID *
Transmit
Symbology ID
Don’t Transmit
Symbology ID *
Don’t Transmit
Check Digit
Don’t Transmit
Application ID
Transmit Symbology
ID
C. GS1 DataBar Expanded Parameters
Don’t Transmit Symbology ID *
Transmit Symbology ID
33
© 2016 unitech Electronics Co., Ltd. All rights reserved.
unitech is a registered trademark of unitech Electronics Co.,Ltd
3.16 Bar Code ID
OFF *
ON
Default
With this function ON, a leading character will be added to the output string
while scanning code, user may refer to the following table to know what kind of
bar code is being scanned.
Please refer to the table below for matching code ID of codes read in.
Code Type
ID
Code Type
ID
UPC-A
UPC-E
EAN-8
EAN-13
CODE 39
CODE 128
Interleave 25
Industrial 25
Matrix 25
Codabar/NW7
CODE 93
CODE 11
China Postage
MSI / PLESSEY
Code 2 of 6
LCD 25
Telepen
GS1 DataBar
Omnidirectional
GS1 DataBar
Limited
GS1 DataBar
Expanded
34
© 2016 unitech Electronics Co., Ltd. All rights reserved.
unitech is a registered trademark of unitech Electronics Co.,Ltd
User Define Code ID
To set the code ID:
1. Scan the symbologies label.
2. Go to the ASCII Tables in Appendix B, scan label that represents the desired
code ID.
Note :
User define code ID will override default value. Program will not check the
conflict. It is possible to have more than two symbologies which have same
code ID.
UPC-A
UPC-E
EAN-13/JAN-13
EAN-8/JAN-8
CODE 39
CODE 128
CODABAR/NW7
Interleave 25
Matrix 25
Industrial 25
CODE 93
CODE 11
ChinaPostage
MSI/PLESSEY
Code 2 of 6
Telepen
35
© 2016 unitech Electronics Co., Ltd. All rights reserved.
unitech is a registered trademark of unitech Electronics Co.,Ltd
LCD25
GS1 DataBar
Omnidirectional ON
GS1 DataBar Limited ON
Reserved5
GS1 DataBar Expanded ON
Reserved6
36
© 2016 unitech Electronics Co., Ltd. All rights reserved.
unitech is a registered trademark of unitech Electronics Co.,Ltd
Chapter 4 – Command Setting
4.1 Interface & Reading Mode Selection
4.1.1 Cradle Interface Selection
USB Mode *
RS232 Mode
Virtual COM
4.1.2 Reading Mode Selection
Trigger ON/OFF *
Good Read OFF
Continuous/Trigger OFF
Testing
Continuous/Auto Power On
Flash/Auto Power On
Flash
Presentation
37
© 2016 unitech Electronics Co., Ltd. All rights reserved.
unitech is a registered trademark of unitech Electronics Co.,Ltd
4.1.3 BT Auto Connection
Disable
Enable*
4.1.4 iOS Hotkey Function
When enabling iOS Hotkey, you may simply double-click the trigger to
toggle the iPhone/iPad Touch Keyboard.
Note: This function is only available for iPhone/iPad.
Enable
Disable*
38
© 2016 unitech Electronics Co., Ltd. All rights reserved.
unitech is a registered trademark of unitech Electronics Co.,Ltd
4.2 Communication Parameters
4.2.1 RS232 Communication Parameters
A. Set Up BAUD Rate
B. Set Up Data Bits
C. Set Up Stop Bits
9600 *
8 Data Bits *
1 Bit*
1200
7 Data Bits
2 Bits
2400
4800
19200
38400
39
© 2016 unitech Electronics Co., Ltd. All rights reserved.
unitech is a registered trademark of unitech Electronics Co.,Ltd
D. Set Up Parity
E. Handshaking
None *
RTS/CTS Disable *
Even
ACK/NAK Disable *
Odd
XON/XOFF Disable *
RTS/CTS Enable
ACK/NAK Enable
XON/XOFF Enable
Mark
Space
40
© 2016 unitech Electronics Co., Ltd. All rights reserved.
unitech is a registered trademark of unitech Electronics Co.,Ltd
4.2.2 Output Characters Parameters
A. Select Terminator
B. Time-out Between Characters
CR*
0 ms *
None
5 ms
CR +LF
10 ms
LF
25 ms
Space
50 ms
HT(TAB)
100 ms
STX-ETX
200 ms
300 ms
41
© 2016 unitech Electronics Co., Ltd. All rights reserved.
unitech is a registered trademark of unitech Electronics Co.,Ltd
4.3 Language Selection
US English *
Hungarian
UK English
Janpanese
Italian
Belgium
Spanish
Portuguese
French
Denmark
German
Netherlands
Swedish
Turkey
Switzerland
Reserved 2
42
© 2016 unitech Electronics Co., Ltd. All rights reserved.
unitech is a registered trademark of unitech Electronics Co.,Ltd
4.4 Reading Level
The Polarity can be sent as standard with black bars high, or reversed with
white bars high.
Black Bars High *
White Bars High
43
© 2016 unitech Electronics Co., Ltd. All rights reserved.
unitech is a registered trademark of unitech Electronics Co.,Ltd
4.5 Accuracy
This setting is to provide the assurance of barcode consistency and to prevent
the misread outcome before the data is sent to the host.Scan the barcode
below to choose how many times you would like to verify the data.
Note: It will cause the scanning process to slow down by choosing more than 1 time to verify
the data.
1 Time *
2 Times
3 Times
4 Times
4.6 Buzzer Beep Tone
High *
Medium
Low
Off
44
© 2016 unitech Electronics Co., Ltd. All rights reserved.
unitech is a registered trademark of unitech Electronics Co.,Ltd
4.7 Sensitivity of Continuous Reading
Mode
A. Quick Setting
Fast *
Slow
B. Same Code Delay Reading Interval
Following code sequences represent the length of time before a barcode can
be rescanned at continuous and flash reading mode. The value can be
defined from 1-50 and they represent 100ms to 5 seconds in100ms interval.
Default value is 3 (0.3 seconds).
To setup same code delay reading interval:
1. Scan the "Begin" label
2. Go the Numeric Bar Codes in Appendix A, Scan label(s),that represents
the same code delay reading interval. They are ranged form 1-50.One step
is represented 0.1second.So the interval is from 0.1 to 5 seconds.
3. Scan the "Complete" label
Repeat the steps 1-3 to set time out of same symbol
1. Begin
3. Complete
2. Numeric Bar
Codes (Appendix A)
45
© 2016 unitech Electronics Co., Ltd. All rights reserved.
unitech is a registered trademark of unitech Electronics Co.,Ltd
4.8 Reverse Output Characters
Disable *
Enable
4.9 Setup Deletion
To setup the deletion of output characters:
1. Scan the label of the desired set below.
2. Scan the label of the desired symbology.
3. Go to the Numeric Bar Codes in Appendix A, scan label(s) that represents
the desired position to be deleted.
4. Scan the “Complete” label of “Character Position to be Deleted”.
5. Go to the Numeric Bar Codes in Appendix A, scan label(s) that represents
the number of characters to be deleted.
6. Scan the “Complete” label of “Number of Characters to be Deleted”.
Repeat the steps 1 – 6 to set additional deletion.
A. Select Deletion Set Number
1st Set
2nd Set
3rd Set
4th Set
5th Set
6th Set
46
© 2016 unitech Electronics Co., Ltd. All rights reserved.
unitech is a registered trademark of unitech Electronics Co.,Ltd
B. Symbologies Selection
Industrial 25
UPC-A
UPC-E
Matrix 25
EAN-13/JAN-13/ISBN-13
CODE 93
EAN-8/JAN-8
CODE 11
CODE 39
China Postage
CODE 128
MSI/PLESSEY
CODABAR/NW7
Code 2 of 6
Interleave 25
Telepen
LCD25
GS1 DataBar Omnidirectional
GS1 DataBar Limited
GS1 DataBar Expanded
None
All Codes
47
© 2016 unitech Electronics Co., Ltd. All rights reserved.
unitech is a registered trademark of unitech Electronics Co.,Ltd
C. Character Position to be Deleted
2. Complete
1. Numeric Bar Codes
(Appendix A)
D. Number of Characters to be Deleted
2. Complete
1. Numeric Bar Codes
(Appendix A)
48
© 2016 unitech Electronics Co., Ltd. All rights reserved.
unitech is a registered trademark of unitech Electronics Co.,Ltd
4.10 Setup Insertion
To setup the insertion of output characters :
1. Scan the label of the desired set.
2. Scan the label of the desired symbology.
3. Go to the Numeric Bar Codes in Appendix A, scan label(s) that represents the
desired position to be inserted.
4. Scan the “Complete” label of “Character Position to be Inserted”.
5. Go to the ASCII Tables in Appendix B or Function Key Tables in Appendix C, scan
label(s) that represents the desired characters to be inserted. Scan the “Complete”
label of “Number of Characters to be Deleted”.
6. Scan the “Complete” label of “Characters to be inserted”.
Repeat the steps 1 – 6 to set additional insertion.
A. Select Insertion Set Number
1st Set
2nd Set
3rd Set
4th Set
5th Set
6th Set
49
© 2016 unitech Electronics Co., Ltd. All rights reserved.
unitech is a registered trademark of unitech Electronics Co.,Ltd
B. Symbologies Selection
Industrial 25
UPC-A
UPC-E
Matrix 25
EAN-13/JAN-13/ISBN-13
CODE 93
EAN-8/JAN-8
CODE 11
CODE 39
China Postage
CODE 128
MSI/PLESSEY
CODABAR/NW7
Code 2 of 6
Interleave 25
Telepen
LCD25
GS1 DataBar Omnidirectional
GS1 DataBar Limited
GS1 DataBar Expanded
None
All Codes
50
© 2016 unitech Electronics Co., Ltd. All rights reserved.
unitech is a registered trademark of unitech Electronics Co.,Ltd
C. Character Position to be Inserted
2. Complete
1. Numeric Bar Codes
(Appendix A)
D. Characters to be Inserted
2. Complete
1. ASCII Table
(Appendix B)
51
© 2016 unitech Electronics Co., Ltd. All rights reserved.
unitech is a registered trademark of unitech Electronics Co.,Ltd
4.11 PAN Configuration
4.11.1 Auto Mode
Auto Mode Enable *
Auto Mode Disable
When “Auto Mode” function is enabled, and the scanner is working at out of
transmission range, the scanned data will be stored to out-of-range memory.
Memory size is approximately 25,000 sets of EAN13 barcode type. The all stored
data will be transmitted to device when the link is reconnected, and the all data
stored in out-of-range memory will be cleared.
4.11.2 Sleep Mode
Sleep Mode OFF*
Sleep Mode 1 min. ON
Sleep Mode10 min. ON
The scanner is equipped with sleep mode function to save battery energy
when the scanner is not used for 1 minute or 10 minutes. During sleep
mode, all the functions and connection will be halted until pressing the
trigger button. The communication with cradle or Bluetooth device will be
reconnected.
52
© 2016 unitech Electronics Co., Ltd. All rights reserved.
unitech is a registered trademark of unitech Electronics Co.,Ltd
4.11.3 Batch Mode
Batch Mode OFF*
Batch Mode ON
Delete Last Data **
Batch Data Read **
Batch Data Clear **
** : Quick Setting Label
The function can be executed directly by scanning barcode instead of doing
the general programming process.
53
© 2016 unitech Electronics Co., Ltd. All rights reserved.
unitech is a registered trademark of unitech Electronics Co.,Ltd
4.11.4 Firmware Version
Scanner Firmware Version**
Cradle Firmware Version**
Scanner MAC Address**
Cradle MAC Address**
** : Quick Setting Label
Display the firmware version of the scanner, please scan above barcode.
54
© 2016 unitech Electronics Co., Ltd. All rights reserved.
unitech is a registered trademark of unitech Electronics Co.,Ltd
Appendix A –Numeric Bar Codes
55
© 2016 unitech Electronics Co., Ltd. All rights reserved.
unitech is a registered trademark of unitech Electronics Co.,Ltd
Appendix B –ASCII Table
56
© 2016 unitech Electronics Co., Ltd. All rights reserved.
unitech is a registered trademark of unitech Electronics Co.,Ltd
57
© 2016 unitech Electronics Co., Ltd. All rights reserved.
unitech is a registered trademark of unitech Electronics Co.,Ltd
58
© 2016 unitech Electronics Co., Ltd. All rights reserved.
unitech is a registered trademark of unitech Electronics Co.,Ltd
59
© 2016 unitech Electronics Co., Ltd. All rights reserved.
unitech is a registered trademark of unitech Electronics Co.,Ltd
Appendix C –Function Key Table
60
© 2016 unitech Electronics Co., Ltd. All rights reserved.
unitech is a registered trademark of unitech Electronics Co.,Ltd
Appendix D–Numeric Bar Codes2
61
© 2016 unitech Electronics Co., Ltd. All rights reserved.
unitech is a registered trademark of unitech Electronics Co.,Ltd
Source Exif Data: 
File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.6
Linearized                      : No
XMP Toolkit                     : Adobe XMP Core 4.0-c316 44.253921, Sun Oct 01 2006 17:14:39
Create Date                     : 2016:01:22 16:45:04+08:00
Creator Tool                    : Acrobat PDFMaker 10.1 Word 版
Modify Date                     : 2016:03:11 13:08:53+08:00
Metadata Date                   : 2016:03:11 13:08:53+08:00
Producer                        : Acrobat Distiller 10.1.1 (Windows)
Keywords                        : 
Format                          : application/pdf
Creator                         : user
Title                           : 
Description                     : 
Document ID                     : uuid:e263b3d2-bd56-409f-8c62-bc2cb2741b5b
Instance ID                     : uuid:52c8402f-a083-4a65-851a-453febddc497
Company                         : Unitech
Comments                        : 
Page Count                      : 75
Page Layout                     : OneColumn
Subject                         : 
Author                          : user
EXIF Metadata provided by EXIF.tools
FCC ID Filing: HLEMS340BT

Navigation menu