Unitech Electronics PA968BTGGR PA968 Rugged Mobile Computer User Manual PDA PA968 UM EN
Unitech Electronics Co., Ltd. PA968 Rugged Mobile Computer PDA PA968 UM EN
User Manual
| Download: |  |
| Mirror Download [FCC.gov] | |
| Document ID | 1099480 |
| Application ID | Ukh5xlijuBqmQv8O2zgUjg== |
| Document Description | User Manual |
| Short Term Confidential | No |
| Permanent Confidential | No |
| Supercede | No |
| Document Type | User Manual |
| Display Format | Adobe Acrobat PDF - pdf |
| Filesize | 183.05kB (2288118 bits) |
| Date Submitted | 2009-04-21 00:00:00 |
| Date Available | 2009-04-21 00:00:00 |
| Creation Date | 2009-01-12 15:01:50 |
| Producing Software | Acrobat Distiller 8.1.0 (Windows) |
| Document Lastmod | 2009-03-26 11:04:17 |
| Document Title | PDA_PA968_UM_EN.book |
| Document Creator | FrameMaker 8.0 |
| Document Author: | user |
unitech PA968 Rugged Mobile Computer H1 H2 Enter ESC 2 abc 4 ghi 7pqrs 8 tuv alpha jkl TAB 3 def 6 mno 9wxyz FUNC User’s Manual © Copyright 2009 unitech Electronics Co., Ltd. 400648G Version 1.0 Preface About This Manual This manual explains how to install, operate and maintain the PA968 Rugged Mobile Computer. No part of this publication may be reproduced or used in any form, or by any electrical or mechanical means, without permission in writing from the manufacturer. This includes electronic or mechanical means, such as photocopying, recording, or information storage and retrieval systems. The material in this manual is subject to change without notice. © Copyright 2009 unitech Electronics Co., Ltd. All rights reserved. unitech global website address: http:\\www.unitech-adc.com Bluetooth is a registered trademark of Bluetooth SIG. Microsoft, Windows and ActiveSync are either registered trademarks or trademarks of Microsoft Corporation. Other product names mentioned in this manual may be trademarks or registered trademarks of their respective companies and are hereby acknowledged. unitech is a member of Oracle Embedded Software Licensing Program. Regulatory Compliance Statements FCC Warning Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: • • • • Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. 1. This Transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. 2. This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. To maintain compliance with FCC RF exposure compliance requirements, avoid direct contact to the transmitting antenna during transmitting. 3. Any changes or modifications (including the antennas) made to this device that are not expressly approved by the manufacturer may void the user’s authority to operate the equipment. RF Radiation Exposure Statement: For body worn operation, this phone has been tested and meets FCC RF exposure guidelines when used with an accessory that contains no metal and that positions the handset a minimum of 1.5 cm from the body. Use of other accessories may not ensure compliance with FCC RF exposure guidelines. Canadian Compliance Statement This Class B Digital apparatus meets all requirements of the Canadian InterferenceCausing Equipment Regulations. Cet appareil numerique de la classe B respecte les exigences du Reglement sur le material broilleur du Canada. European Conformity Statement Declaration of Conformity with Regard to the R&TTE 1999/5/EC and EMC 89/336/ EEC directives. Battery Notices This unit is equipped with a battery pack and backup battery. Both batteries will discharge after an extended period of not being used. When both batteries are discharged, recharge the unit for 16 hours in order to fully charge the main battery and backup battery. If the main battery is removed, the backup battery ensures the data on SDRAM is safe for up to 8 hours. To prevent data loss, do not leave the mobile computer uncharged with the main battery removed for an extended period. Battery Charge Notice It is important to consider the environment temperature whenever you are charging the Lithium-Ion battery pack. The process is most efficient at normal room temperature or slightly cooler. It is essential that you charge batteries within the stated range of 10°C to 40°C. Charging batteries outside of the specified range could damage the batteries and shorten. ii About This Manual Storage and Safety Notice Although charged Lithium-Ion batteries may be left unused for several months, their capacity may be depleted due to build up of internal resistance. If this happens they will require recharging prior to use. Lithium-Ion batteries may be stored at temperatures between -20°C to 60°C, however they may be depleted more rapidly at the high end of this range. It is recommended to store batteries within normal room temperature. iii Table of Contents Preface About This Manual Regulatory Compliance Statements ............................................................................. i FCC Warning Statement.......................................................................................................... i Canadian Compliance Statement ............................................................................................ ii European Conformity Statement ............................................................................................. ii Battery Notices ...................................................................................................................... ii Battery Charge Notice ............................................................................................................. ii Storage and Safety Notice...................................................................................................... iii Chapter 1 Getting Started Introducing the PA968 ....................................................................................................... Features ................................................................................................................................... Package Contents ............................................................................................................... A Tour of the PA968............................................................................................................ Front View............................................................................................................................... 4 Back View ............................................................................................................................... 5 Setting up the PA968.......................................................................................................... 6 Installing the Battery ............................................................................................................... 6 Charging the Battery............................................................................................................... 8 Charging the battery with USB charging cable.................................................................. 8 Charging the battery with the cradle.................................................................................. 8 Checking the LED status ................................................................................................... 9 Checking the Battery Status .............................................................................................. 9 Connecting the terminal to a host (PC/ Notebook) ................................................................. 9 Turning the terminal on for the first time ............................................................................... 10 Powering On ......................................................................................................................... 10 Calibrating the screen...................................................................................................... 10 Chapter 2 Using the Hardware 12 Using the SD/MMC Memory Card ................................................................................ 12 Inserting a Storage Card....................................................................................................... 12 Removing a Storage Card .................................................................................................... 12 Using the SIM Card ........................................................................................................... 13 Inserting the SIM card........................................................................................................... 13 Using the Camera .............................................................................................................. 14 Using the Fingerprint Reader ....................................................................................... 14 Using the Barcode Laser Scanner .............................................................................. 16 Chapter 3 Getting Connected 18 iv Establishing Device-PC Connection.......................................................................... 18 Installing Microsoft ActiveSync ............................................................................................. 18 Connecting the Device to Your Computer ............................................................................ 19 Using ActiveSync to Exchange Files ........................................................................ Bluetooth Connection ...................................................................................................... GPRS Connection.............................................................................................................. WiFi Connection ................................................................................................................. 20 Using the Summit Utilities..................................................................................................... Admin Login..................................................................................................................... Scan Available AP ........................................................................................................... Commit and Activate ....................................................................................................... 28 28 28 29 Chapter 4 Barcode Scanner Programs 21 24 26 31 Scanner Setting .................................................................................................................. 31 Scan2Key .............................................................................................................................. 31 Barcode Symbologies........................................................................................................... 32 Barcode Symbologies 2D ..................................................................................................... 33 Chapter 5 Advanced Settings 34 Performing a Hardware Reset ...................................................................................... 34 Performing a Warm Boot ...................................................................................................... Performing a Cold Boot ........................................................................................................ Method 1: From WinCE ................................................................................................... Method 2: From Hardware............................................................................................... Appendix System Specification 34 34 35 35 36 vi Chapter 1 Getting Star ted Introducing the PA968 Thank you for purchasing the PA968 Rugged Mobile Computer. Your PA968 was designed for users who need a compact and durable mobile computer for data collection and real time transactions. The PA968 is a rugged, compact and lightweight palm-size mobile computer using Windows CE 5.0 operating system, and incorporating an integral bar code scanning device, advanced fingerprint reader, high-resolution digital camera, color LCD with touchscreen, keypad, and wireless and GPRS communication capability. It provides users with a standard Windows-based environment for customizing and operating the device. To reduce TCO, the PA968 is sealed to meet IP65 standards and has undergone multiple drop tests to prevent downtime. Copyright 2009 unitech Electronics Co., Ltd. All rights reserved. unitech is a registered trademark of unitech Electronics Co., Ltd. Chapter 1 Getting Started Features Powerful system • Microsoft Windows CE 5.0 operating system • Intel PXA270 processor with speed of up to 520 MHz Audio • MIC • Speaker • Headset connector • Receiver System memory • 128 MB SDRAM • 320 MB Flash ROM Picture Capture • Built-in 2.0M Pixel camera • 1/4-inch CMOS sensor Display • 3.5” TFT LCD panel with touchsensitive screen • 240 x 320 resolution • Supports display rotation • Polycarbon LCD protection foil (Pre-installed) Fingerprint Reader • Resolution 500 DPI • 256 gray scale • Fingerprint image • Live finger verification Barcode scanner • Built-in Symbol SE-950 Scan Engine Communication • USB 1.1 Client/ Host • Bluetooth 2.0 EDR (supports Bluetooth Printer, Bluetooth Modem, Bluetooth ActiveSync) • UMTS WCDMA/HSDPA 850/1900/ 2100MHz • 3.5G Five bands GSM/GPRS 850/ 900/1800/1900Mhz, UMTS WCDMA/HSDPA 850/1900/ 2100Mhz, GPRS Edge • Integrated WPAN/WLAN/WWAN • Built-in GPS Expansion slot • SD memory slot, supports up to 2G Wireless connectivity • 802.11b/g • Bluetooth • GPRS Battery life • Standby above 24 hours • With BT, GPS, GPRS simultaneously on: above 4 hours • Charging time: 4 hours • Embedded backup battery cell User-friendly interface • Special keys to launch particular applications and display the onscreen keyboard • Keys for barcode scanning Chapter 1 Getting Started Package Contents After opening the box, ensure the following accessories for the PA968 are present: H1 H2 Enter ESC 4 ghi 2 abc jkl TAB 7pqrs 8 tuv alpha 3 def 6 mno 9wxyz FUNC PA968 Battery Pack Stylus Elastic Stylus String CD-ROM Copyright 2009 unitech Electronics Co., Ltd. All rights reserved. unitech is a registered trademark of unitech Electronics Co., Ltd. Chapter 1 Getting Started A Tour of the PA968 The following sections describe the main components and features of the PA968. Front View No. 1. Component Status indicator 2. LCD touch screen 3. Microphone 4. Power button 5. 6. 7. Fingerprint reader Receiver Scanner trigger button Keypad 8. Description Indicates the terminal operating statuses. LED indicators from left to right: - GPRS/GPS Communication - Engine reading - Power charging Displays the applications and data stored on your device. It is touch-sensitive and responds to the stylus or finger. Inputs audio into your device when recording the voice notes. If the device is off, press this button to turn it on. Alternatively, when the unit is on, this key must be pressed and held down for about three seconds in order to turn the device off. Place the finger on the scanner for fingerprint reading. Enables you to hear GSM voice from PA968. Press to activate the barcode laser scanner. Keypad interface for controlling the PA968. Chapter 1 Getting Started 9. Universal connector Back View Connects your device to a USB charging/ communication cable. This USB cable connects to the computer’s USB port and accepts the 12V AC adapter to provide power to the PA968. The unit can simultaneously recharge and perform an Activesync operation. You can also use it to connect peripheral hardware, such as a docking station, to your device. This port can also support USB/RS232 hosting for devices such as a USB/RS232 scanner, keyboard, or USB memory key. 10 No. 1. 2. Reset button 3. 4. Speaker Battery compartment 5. Barcode scanner window Antenna Digital camera len LED Flash light Memory card slot Battery compartment tab 6. 7. 8. 9. 10. Component Earphone jack Description Port to plug in the headset connector. Use in noisy environments. Press the end of the stylus into the button to reset your device. Enables you to hear audio from PA968. Houses the removable and rechargeable 7.4 V, 1850 mAh battery pack. Scan barcodes where the laser pass through. GSM antenna. Captures quality images. Lights up images for camera. Accommodates SD memory card. Opens the battery compartment. Copyright 2009 unitech Electronics Co., Ltd. All rights reserved. unitech is a registered trademark of unitech Electronics Co., Ltd. Chapter 1 Getting Started Setting up the PA968 This section explains how to install and charge the battery, how to check battery status, how to turn on the terminal, and how to calibrate the screen. Installing the Battery WARNING! There is a risk of fire and burns if the battery pack is handled improperly. DO NOT disassemble, crush, puncture, short external contacts, or dispose the battery pack in fire or water. DO NOT attempt to open or service the battery pack. Dispose of used batteries according to local recycling guidelines in your area. A backup battery cell is embedded into your device to prevent data loss when the removable battery pack is removed or completely discharged. This backup battery will keep the data and system setting for up to 8 hour if the main battery is removed. NOTE: To enable the internal battery cell to provide backup power supply, charge your device with the main battery pack for at least 16 hours. NOTE: To power on the device properly, make sure replacing the battery compartment cover after installing the battery. 1. Open the battery compartment cover by sliding the tabs on both sides in the direction of the arrows shown and lift the cover up. Battery Compartment tab 2. Turn the backup battery switch on. Backup battery switch Chapter 1 Getting Started 3. Position the battery pack, making sure the battery contacts are aligned with the contacts in the compartment and the battery is placed on top of the plastic tab. Battery compartment contacts 4. Slide the battery pack while simultaneously pulling the plastic tab until the battery clicks into place. Plastic tab 5. Replace the battery compartment cover, push down the tabs and slide them back into place as shown. NOTE: Make sure the battery compartment cover is securely closed, or you may be unable to turn the terminal on. Copyright 2009 unitech Electronics Co., Ltd. All rights reserved. unitech is a registered trademark of unitech Electronics Co., Ltd. Chapter 1 Getting Started Charging the Battery Before using the terminal for the first time, you need to charge it for about 16 hours. After that, you can charge the terminal for 4 hours to recharge the battery to full capacity. Charge the terminal using the USB charging cable or the docking station. CAUTION! Operating the terminal for the first time without the AC adapter, and without fully charging the backup battery may result in loss of data stored in RAM memory. When the main battery is removed, the backup battery retains RAM data in memory for 8 hours. Please charge the battery for the period to avoid data loss in RAM memory. NOTE: Turn the backup battery switch on before charging the battery. Data you entered may not be properly stored until the built-in backup battery has been fully charged. Charging the battery with USB charging cable 1. Press and hold the release button on both sides of the USB charging cable and connect it to PA968 (1). 2. Plug the AC adapter cable into the power jack of the USB charging cable (2). 3. Plug the AC adapter cord into an electrical outlet (3). Charging the battery with the cradle 1. Plug the AC adapter cable into the power jack of the cradle (1). 2. Plug the AC adapter cord into an electrical outlet (2). Chapter 1 Getting Started 3. Slide the terminal into the cradle until it clicks into place. Terminal LED indicators from left to right: - GPRS/GPS Communication - Engine reading - Power charging Cradle LED indicator 4. The connection is secure when the bottom edge of the terminal is aligned with the cradle, and the LED indicator on the terminal lights up red. Checking the LED status Terminal LED Light Description GPRS/GPS Communication Flashing Red GPRS/GPS power is on Flashing Green Communicating Engine reading Solid Red Reading Solid Green Decoded Solid Red Charging Solid Green Fully charged Power charging Solid Green Power is on Communication Flashing Green Data synchronization is active Power charging Cradle Checking the Battery Status If the battery level becomes low in the course of normal use, a status icon appears on the device screen indicating low or very low battery status. In both cases, perform an Activesync operation to back up your data, then recharge your device as soon as possible. CAUTION! Once the device is shut down, you should recharge the device within 48 hours. Otherwise you will lose all data including files stored in the RAM memory. Connecting the terminal to a host (PC/ Notebook) Use the USB charging cable to connect the PA968 to a PC/ Notebook in order to use with Activesync. NOTE: To avoid low battery situation while synchronizing, you should connect the power supply. 1. Press and hold the release button on both sides of the USB charging cable and connect it to PA968 (1). Copyright 2009 unitech Electronics Co., Ltd. All rights reserved. unitech is a registered trademark of unitech Electronics Co., Ltd. Chapter 1 Getting Started 2. Connect the USB charging cable to the USB port on a PC/ Notebook and plug the AC adapter cable into the power jack of the USB charging cable (2). 3. Plug the AC adapter cord into an electrical outlet (3). Turning the terminal on for the first time After you have initially charged your device for about 16 hours, the terminal is ready to be used. You can now start up your device where you will calibrate the display, learn some basic stylus usage, and set up the system time zone, date and time. Powering On 1. Turn on your device by pressing the power button on the front panel. NOTE: The PA968 screen ships with a protective plastic film. You may remove it by peeling from the corner. The screen will be more susceptible to scratching without the film, but will be more readable. 2. The Welcome screen appears for a moment followed by the WINCE screen. Calibrating the screen The calibrate screen automatically appears when the terminal is powered on for the first time or after the system is reset. To calibrate the screen at any time, follow these instructions. 1. Tap Start → Settings, and then switch to Control Panel tab. 2. Tap the Stylus icon. The Stylus Properties window appears. 10 Chapter 1 Getting Started 3. Tap Recalibrate to calibrate the screen. The alignment screen appears. NOTE: Or press Func key and ESC key simultaneously to bring up the alignment screen. 4. Tap the cross hair firmly and accurately. 5. Continue tapping the cross hair until the screen has been calibrated. 6. Press Enter key to accept the new settings. Press Esc key to keep the old settings. 11 Copyright 2009 unitech Electronics Co., Ltd. All rights reserved. unitech is a registered trademark of unitech Electronics Co., Ltd. Chapter 2 Using the Hardware Using the SD/MMC Memory Card PA968 has an expansion slot compatible with a range of SD and MMC storage cards, which are primarily used to backup or transfer files and data. The slot also support SDIO cards for added connectivity options. Inserting a Storage Card 1. Remove the two screws from the SD compartment cover and remove the cover. 2. Insert the SD card with the notched corner as shown. 3. Push the card into the slot until you feel the SD card click into place. 4. Screw the SD compartment cover. Removing a Storage Card 1. Remove the two screws from the SD compartment cover and remove the cover. 2. Press the card in and release. The card pops out. 3. Remove the card from the slot. 12 Chapter 2 Using the Hardware Using the SIM Card The PA968 has a slot for GPRS SIM card inside the battery compartment. CAUTION! Before installing the SIM card, please backup your data to prevent data loss because of a low backup battery. Inserting the SIM card 1. Remove the battery compartment cover and the main battery. See Installing the Battery on page 6. 2. Slide the cover of the SIM card slot to the left to release the latch. 3. Lift the cover and insert the SIM card into the cover with notched corner up, contacts down as shown. 4. Put down the cover on the slot, then slide the cover to the right to lock the SIM card. 5. Put the battery back into the battery compartment and replace the battery compartment cover. 13 Copyright 2009 unitech Electronics Co., Ltd. All rights reserved. unitech is a registered trademark of unitech Electronics Co., Ltd. Chapter 2 Using the Hardware Using the Camera The device has a powerful 2.0-megapixel digital camera to deliver superior image capture performance. To launch the demo program, follow these instructions. 1. Tap Start → Program → Utilities → CameraDemo. 2. Tap Preview → Start to activate the camera. 3. Tap Capture → Image to capture an image. 4. Tap Capture → Start Video to start recording a video. Tap Capture → End Video to end the recording. Using the Fingerprint Reader PA968 equips a fingerprint reader using advanced biometric finger identification technology. To launch the demo program, follow these instructions. 1. Tap Start → Program → Utilities → FingerDemo. 14 Chapter 2 Using the Hardware 2. Tap Snap to test the fingerprint reader. “Please sweep your finger!” message pops up. Gently sweep the finger inwards on the reader. 3. Tap Enroll to enroll a fingerprint. “Please sweep your finger!” message pops up. 4. Gently sweep the finger inwards on the reader five times following on-screen instructions until a pop-up window appears informing you the reading quality. Click OK. NOTE: 15 Class A represents a high quality of the enrolled fingerprint data, while Class C a low quality. Copyright 2009 unitech Electronics Co., Ltd. All rights reserved. unitech is a registered trademark of unitech Electronics Co., Ltd. Chapter 2 Using the Hardware 5. Tap Match to carry out identification. “Please sweep your finger!” message pops up. Gently sweep the finger inwards on the reader following on-screen instructions until a message pops up saying “Matching Success!” or “Matching Fail!”. Using the Barcode Laser Scanner PA968 has an integrated laser scanner which reads all major barcode labels with excellent performance. NOTE: The reading software must be enabled in order to operate the scanner. This can be a user-loaded application or a pre-loaded utility such as Scanner Settings and Scan2Key. To launch the Scanner Control Panel, follow these instructions. 1. Tap Start → Settings, and then switch to Control Panel tab. 2. Tap the Scanner icon. The Scanner Control Panel appears. NOTE: Or press Func key and “7” button simultaneously to bring up the Scanner Control Panel screen. In the Scanner Control Panel screen, you can configure barcode scanner parameters such as enabling or disabling barcode symbologies, setting data transmission options, configuring magnetic and proximity reading options, and setting power management options. See Barcode Symbologies on page 32. To test the barcode laser scanner, follow these instructions. 1. Tap the Test tab to activate the demo program. 16 Chapter 2 Using the Hardware 2. Tap Tools → Enable Scan. Or tap Tools → Auto-Scan → Start Auto-Scan. Define the scan interval. Tap Start. 3. Aim the laser scanner at the selected barcode, and press either one of the scanner trigger button on the device. If you enable Auto-Scan, you don’t have to press any button. Aim the laser scanner at the selected barcode while the laser emits light at regular intervals. The scanned barcode data appears on the screen. 4. Tap Tools → Auto-Scan → Stop Auto-Scan. 17 Copyright 2009 unitech Electronics Co., Ltd. All rights reserved. unitech is a registered trademark of unitech Electronics Co., Ltd. Chapter 3 Getting Connected The PA968 enables users to link to a host computer using an RS-232, or Bluetooth, WiFi, and GPRS connection for data communication. This chapter provides an overview of PA968 communication options. Establishing Device-PC Connection Installing Microsoft ActiveSync In order to exchange data between your computer and the PA968, Microsoft ActiveSync must be installed on your computer. Use the USB/RS232 charging cable that comes with your device or the docking station to connect the device to your computer. NOTE: If you have a previous version of the Microsoft ActiveSync installed in your computer, uninstall it first before installing the latest version of Microsoft ActiveSync. To install Microsoft ActiveSync on your computer: 1. Close any open programs, including those that run at startup, and disable any virus-scanning software. 2. Download the ActiveSync software from the Microsoft ActiveSync Download page at http://www.microsoft.com/downloads/details.aspx?FamilyID=7269173a-28bf-4cac-a682-58d3233efb4c&DisplayLang=en. 3. Browse to the location of the downloaded file, and double-click it. The installation wizard begins. 4. Follow the instructions on the screen to install Microsoft ActiveSync. 18 Chapter 3 Getting Connected Connecting the Device to Your Computer 1. After ActiveSync has been installed, connect PA968 to your PC as described in Connecting the terminal to a host (PC/Notebook) to a PC on page 10. 2. Turn the PA968 on. 3. ActiveSync starts automatically and configure the USB port to work with the PA968. The New Partnership setup wizard automatically starts. NOTE: If ActiveSync doesn’t start automatically, click Start → Programs → Microsoft ActiveSync. NOTE: If a message appears indicating that it is unable to detect a connection, click the Cancel button and manually configure the communication settings. 4. Follow the on-screen instructions. 5. When the configuration process is complete, the ActiveSync window appears. 6. Synchronization will be initialized and will take place if you’ve chosen to synchronize periodically or upon connection. NOTE: 19 Your computer can create a partnership with multiple PA968s. Also, a PA968 can create a partnership with up to two computers. Copyright 2009 unitech Electronics Co., Ltd. All rights reserved. unitech is a registered trademark of unitech Electronics Co., Ltd. Chapter 3 Getting Connected Using ActiveSync to Exchange Files You can use ActiveSync to exchange information from your device your computer and vice versa. Changes you make to the information on one location will not affect the information on the other one. If you want to automatically update information on both your device and computer, synchronize the information instead. You can copy two types of information to your device: files and Pocket Access Windows CE Store information. The following procedure only applies to copying files. Refer to the ActiveSync Help on your computer for instructions on how to copy Pocket Access Windows CE Store information. NOTE: Files created on your computer may need to be converted by ActiveSync so that they can be viewed and edited on your device, and vice versa. To copy files: 1. Connect your device to your computer. 2. In ActiveSync on your computer, click Explore. Windows Explorer opens the Mobile Device window for your device. 20 Chapter 3 Getting Connected 3. Locate the file that you want to copy on your device or computer. 4. Do either one of the following: – To copy the file to your device, right-click the file and click Copy. Place the cursor in the desired folder for your device, right-click, then click Paste. – To copy the file to your computer, right-click the file and click Copy. Place the cursor in the desired folder for your computer, right click, then click Paste. Bluetooth Connection Your device is equipped with Bluetooth wireless technology that you can use to synchronize information with a computer equipped with a Bluetooth adapter or access point. Bluetooth wireless technology allows you to communicate with the computer whenever it is within range. Follow these instructions to set up a Bluetooth connection. 1. Tap Start → Programs → Bluetooth → BTPowerON. 2. Check Bluetooth Module Power on. Tap OK. 21 Copyright 2009 unitech Electronics Co., Ltd. All rights reserved. unitech is a registered trademark of unitech Electronics Co., Ltd. Chapter 3 Getting Connected 3. Tap Start → Settings → Control Panel → Bluetooth Device Properties. 4. Tap Scan Device. Select a device you want to connect. Double tap the desired device and check Trusted and then Active. 5. On your computer, click ActiveSync → Connection Settings. Select your BT COM port and click OK. 22 Chapter 3 Getting Connected 6. On your terminal, tap Start → Programs → Bluetooth → BTActiveSync. 7. The BTActiveSync icon appears on the taskbar. Double tap the icon. 8. Tap More. 9. Tap Inquiry. Select a device you want to synchronize. Tap OK. 10. Tap BTActiveSync icon again. Tap Sync. ActiveSync begins. 23 Copyright 2009 unitech Electronics Co., Ltd. All rights reserved. unitech is a registered trademark of unitech Electronics Co., Ltd. Chapter 3 Getting Connected GPRS Connection Insert the SIM card in your terminal first. See Using the SIM Card on page 13. NOTE: Please turn off the SIM card lock if your SIM card is password protected. 1. Tap Start → Programs → GPRS → 32WANDEMO. 2. Tap Power on. 3. The screen displays “Modem Power Status is ON”. Tap OK. 24 Chapter 3 Getting Connected 4. Tap Start → Programs → GPRS → 32WANRAS. The 32WANRAS DialUp window appears. Tap Open Connection. 5. The Connection window appears. Tap Connect. 6. The GPRS icon on the taskbar indicating the signal strength. Tap Disconnect Connection, you can end the GPRS connection. 25 Copyright 2009 unitech Electronics Co., Ltd. All rights reserved. unitech is a registered trademark of unitech Electronics Co., Ltd. Chapter 3 Getting Connected WiFi Connection Unitech terminals come with built-in RF facility. A wireless network can be added either when the network is detected or by manually entering settings information. Before following these instructions, make sure if authentication information is needed. 1. Tap Start → Programs → Summit → scu. The Summit Client Utility window appears. 2. Select Third Party Config from the drop down menu of Active Profile. 3. A pop-up window appears “A Power Cycle is required to make settings activate properly.” Tap OK, and then tap OK to exit the Summit Client Utility. 26 Chapter 3 Getting Connected 4. Tap Start → Programs → Utilities → BootMode. Tap Warm Boot to warm start the terminal and load the previous settings. 5. The RF setting window pops up once the RF signal is detected. Tap Add New or double tap a preferred network. 6. Enter the Network name (SSID). Uncheck The key is provided automatically. Enter the network key. Tap OK. 7. The network icon appears on the taskbar when the RF is connected. 27 Copyright 2009 unitech Electronics Co., Ltd. All rights reserved. unitech is a registered trademark of unitech Electronics Co., Ltd. Chapter 3 Getting Connected Using the Summit Utilities You can use the Summit Client Utility tool to setup or change the WiFi settings. Admin Login 1. To login as an administrator, tap Admin Login. 2. Enter the Admin Password. (Default password: SUMMIT) Scan Available AP 1. Under Profile tab, tap Scan for available AP. 28 Chapter 3 Getting Connected 2. You may select a desired AP to create a new profile. Tap Configure. 3. Tap Yes to create the new profile. 4. Enter the WEP key or network key. Tap OK. Commit and Activate 1. Tap Commit to activate the setting. 29 Copyright 2009 unitech Electronics Co., Ltd. All rights reserved. unitech is a registered trademark of unitech Electronics Co., Ltd. Chapter 3 Getting Connected 2. Under Main tab, select the profile you want to activate. 3. A pop-up window appears “A Power Cycle is required to make settings activate properly.” Tap OK, and then tap OK to exit the Summit Client Utility. 4. Tap Start → Programs → Utilities → BootMode. Tap Warm Boot to warm start the terminal and load the previous settings. 5. The Summit icon on the taskbar indicating the AP is connected. Double tap this icon to bring up Summit Control Utility. Tap Disable Radio, you can disconnect the AP. Under Status tab, you can see the IP address, signal strength and quality. 30 Chapter 4 Barcode Scanner Programs PA968 provides an option for the barcode scanner, allowing you to scan and decode various types of 1D/2D barcodes. Scanner Setting When it is necessary for the user to change the default barcode symbology for a different application, the Scanner Control Panel provides the ability to change default symbology, place delimiter characters behind scanned data, and save the settings. Tap Start → Settings → Control Panel → Scanner. The Scanner Control Panel appears. NOTE: Press Func key and “7” button. Scan2Key The Scan2Key application routes input from a scanner port to a keypad buffer, making all input from the scanner emulate input from the keypad. Using Scan2Key, scanned data will be directed from the scanner port to any waiting (active/focused) text editor such as MS Mobile Word or a text box in an applicaton. 31 Copyright 2009 unitech Electronics Co., Ltd. All rights reserved. unitech is a registered trademark of unitech Electronics Co., Ltd. Chapter 4 Barcode Scanner Programs Barcode Symbologies Barcode Symbology Enable/ Disable Check Transmit Char/Digit Check verification Char/Digit Australian Post British Post Canadian Post Codabar YES YES YES YES Code 11 Code 128 / EAN 128 Code 39 YES YES YES YES YES Code 93 Dutch (KIX) Post EAN 13 Others Send bar width data YES Transmit start & stop char, *data length *data length *data length YES YES YES YES For ASCII, Transmit start & stop char, Append mode, *data length *data length YES EAN 8 YES YES IATA 2 of 5 Interleaved 2 of 5 ISBT Japanese Post Korean Post Matrix 2 of 5 MSI Planet Postnet RSS (Databar) UPC A YES YES YES YES YES YES YES YES YES YES YES 2 digit addenda, 5 digit addenda, Addenda required, Include addenda separator 2 digit addenda, 5 digit addenda, Addenda required, Include addenda separator *data length *data length UPC E YES YES UPC E1 YES YES NOTE: YES YES YES YES YES YES YES *data length *data length *data length *data length 2 digit addenda, 5 digit addenda, Addenda required, Include addenda separator, Send number system 2 digit addenda, 5 digit addenda, Addenda required, Include addenda separator, Send number system, Expanded UPC-E 2 digit addenda, 5 digit addenda, Addenda required, Include addenda separator, Send number system, Expanded UPC-E *Value Adjustable Scanner Control Panel Version 5.14 32 Chapter 4 Barcode Scanner Programs Barcode Symbologies 2D Barcode Symbology Enable/ Disable Aztec Codablock F Code 49 Data Matrix EAN-UCC Composite MaxiCode MicroPDF417 OCR PDF-417 QR Code TLC-39 (TCIF Linked Code 39) NOTE: 33 Check Transmit Char/Digit Check verification Char/Digit Others YES YES YES YES YES Runes, *data length *data length *data length *data length UPC composite, *data length YES YES YES *data length *data length OCR mode, OCR direction, Template, Group G, Group H, Check character *data length YES YES YES *Value Adjustable Scanner Control Panel Version 5.14 Copyright 2009 unitech Electronics Co., Ltd. All rights reserved. unitech is a registered trademark of unitech Electronics Co., Ltd. Chapter 5 Advanced Settings Performing a Hardware Reset You may have to perform a reset if the device freezes (i.e., the device no longer responds to the buttons or tapping on the screen). A soft reset allows your device to get a fresh start, similar to rebooting a computer. This will restart your device and adjust memory allocation. All records and entries are retained after a soft reset. Unsaved data in open programs may lost. Performing a Warm Boot 1. Remove the stylus from its holder. 2. Lightly press the tip of the stylus to the reset button located at the rear side of the terminal. Performing a Cold Boot A cold boot will erase all data and all programs you have added, and will restore the device to the default factory settings. Never perform a cold boot unless a warm boot does not correct your problem. When you perform your next ActiveSync operation, you can restore any data that you previously synchronized to your computer or you can restore data that you backed up to a storage card. 34 Chapter 5 Advanced Settings Method 1: From WinCE 1. Tap Start → Programs → Utilities → Bootmode. The BootMode Screen appears. 2. Tap Cold Boot. The system is reset and you will lose all data including all files in the RAM memory. Method 2: From Hardware 1. Remove the battery compartment cover and the main battery. See Installing the Battery on page 6. 2. Turn the backup battery switch off. 3. Turn the backup battery switch on. 4. Put the battery back into the battery compartment and replace the battery compartment cover. System will cold boot. NOTE: 35 When you perform hard reset, the data and time settings will not be retained. Formats, preferences, and other settings are restored to their default factory settings. Copyright 2009 unitech Electronics Co., Ltd. All rights reserved. unitech is a registered trademark of unitech Electronics Co., Ltd. Appendix System Specification Processor / Memory CPU Memory Operation System Keypad Display Communication WinCE.NET 5.0 24-Key, including numeric key, alpha key and function key, swappable keypads 240x320 pixel, 3.5” color transflective TFT-LCD with touch screen & backlight USB 1.1 Client/ Host Bluetooth 2.0 EDR IEEE 802.11b/g 3.5G Mobile communication system 1D Laser scanner engine 2D Imager (optional) Resolution 500dpi, 256 grey scale 2.0M Pixel 4800 candle power LEDs, Vibrator MIC, speaker, headset connector, receiver CIF - 352x240 pixel, 15 pix/sec GPS SDIO memory slot Main battery 13.69 Watts Li-ion battery pack Backup battery One rechargeable Ni-MH backup battery Weight 500g with battery Dimension Approximately 199.5mm X 88mm X 43.3mm (Antenna length excluded) Operating temperature -10 °C ~ 50 °C Charging temperature 10 °C ~ 40 °C Storage temperature -20 °C ~ 60 °C Relative humidity 5% ~ 95% (non-condensing) Drop test to concrete 1.5 Meter Environmental sealing IP65 BT Only WLAN + BT GPRS + BT (for Windows CE 5.0) CE, FCC, BSMI, VCCI, CCC, RoHS Compliance Microsoft Visual Studio 2005 Microsoft Windows CE 5.0 SDK (from unitech) Oracle Database Lite Navigator (US, Canada, Europe area) Desktop USB Cradle USB communication and charging cable AC adaptor (with regional power cord) Vehicle Cradle Battery charger 4 slot Multi-Bay Ethernet Cradle Barcode Scanner Fingerprint Reader Camera Flash Light Indicator Audio Video Address Locating Expansion Slot Power Source Enclosure Environmental Models Regulatory Approvals Software Accessories Intel PXA270, 520MHz SDRAM: 128MB Flash ROM: 320MB 36
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.4 Linearized : No Page Mode : UseOutlines XMP Toolkit : 3.1-701 Creator Tool : FrameMaker 8.0 Modify Date : 2009:03:26 11:04:17+08:00 Create Date : 2009:01:12 15:01:50Z Metadata Date : 2009:03:26 11:04:17+08:00 Format : application/pdf Title : PDA_PA968_UM_EN.book Creator : user Producer : Acrobat Distiller 8.1.0 (Windows) Document ID : uuid:6e8cf961-9406-4071-af50-6ea8d50b7cf9 Instance ID : uuid:f71a86fc-3a28-420c-bc2e-ff7c5e5b7239 Page Count : 44 Author : userEXIF Metadata provided by EXIF.tools