Universal Electronics 4868 Comcast XR8 RF4CE Serial Dongle 2012 User Manual

Universal Electronics Inc Comcast XR8 RF4CE Serial Dongle 2012

User Manual

Enjoy your XFINITY® TV right away!Pair your XR8 and Xfinity Remote to get started.Your Xnity Remote can be paired with the XR8, allowing you to control your set-top box or DTA even when the device is placed out of line-of-sight (for example, in an entertainment center or behind your TV). Xnity Remotes can be identied by an XR logo on the back of the remote.See the “Compatible Devices” section on the back of this user guide to verify that your set-top box or DTA and remote are compatible with the XR8. To pair your XR8 and Xnity Remote, follow the steps below: HERE’S HOW:1. Turn on your TV and set-top box or DTA. 2. Plug the XR8 into the IR Input port* located on the rear panel of your set-top box or DTA. *Note: This port may also be labeled IR, IR-In, IR Receive, or EXT IR IN.3. Wait 3-5 seconds for the solid red LED on top of the XR8 to turn off.It’s simple to pair your XR8 with your Xfinity Remote for Out-of-Sight control. XR8 Xfinity Remote Out-of-Sight AdapterUSER’S GUIDEXR8 Xfinity Remote Out-of-Sight AdapterUSER’S GUIDE4. Press and release the PAIR button on the back of the XR8. The LED on top of the XR8 will start blinking. 5. Press and hold the Setup button on your Xnity Remote until the LED changes from red to green. Then, press and release the Xnity button. Note: You must press the PAIR button on the XR8 before you press the Xnity button on your Xnity Remote.6. If the LED on the Xnity Remote blinks green twice, pairing was successful. Press Channel Up to verify that your set-top box or DTA responds as expected. 7. If the LED on the Xnity Remote blinks red, then green, and then red, pairing was unsuccessful. Check the “Compatible Devices” section to verify that your set-top box or DTA supports the XR8.xfinity.com ©2013 Comcast Corporation. All rights reserved.
FCC Compliance StatementThis equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC rules. These limits are designed to provide reason-able protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio fre-quency energy and, if not used in accordance with the instructions, may cause harmful interference to radio communications. There is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, the user is encouraged to try to correct the interference by one or more of the following measures: • Reorient or relocate the receiving antenna. • Increase or decrease the separation between the equipment and receiver. • Connect the equipment into an outlet on a circuit different from that which the receiver is connected. • Consult the dealer or an experienced remote control/TV technician for help. • It is strongly recommended that the TV be plugged into a separate wall outlet.The user is cautioned that changes and mod-ications made to the equipment without the approval of the manufacturer could void the user’s authority to operate this equipment. This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. :QCan I pair more than one Xnity Remote with the XR8? :AYes, the XR8 supports pairing with up to ve Xnity Remotes.:QWhy can’t I use my other remotes after pairing my Xnity Remote with the XR8?:ASome set-top boxes only support Xnity Remotes when using the XR8. Simply replace your old remote with another Xnity Remote if you need more than one remote! :QDuring pairing, why does the LED blink red and then green on the Xnity Remote?:AEither a button other than the Xnity button was pressed, or the Xnity Remote timed out before the Xnity button was pressed. Repeat the pairing steps. COMPATIBLE DEVICES:DTAuDTARNG100RNG110RNG150RNG150NRNG200NDCX3200DCX3200-MDCX3400DCX3400-MDCX3501FREQUENTLY ASKED QUESTIONS ABOUT PAIRING:QDuring pairing, why does the LED blink red, then green, then red on the Xnity Remote? :AThe Xnity Remote you are trying to pair with the XR8 cannot nd the XR8. Unplug the XR8 and plug it back in, making sure the red LED on top of the XR8 comes on for 3-5 seconds. Then, repeat the steps to pair the XR8 and Xnity Remote. :QWhen paired, why does the LED blink green, then red on the Xnity Remote when a button is pressed? :AThe XR8 may have lost power or may be out of communication range. Try moving closer to your set-top box or DTA and make sure the XR8 is securely connected. If this does not x the issue, follow the steps to re-pair the XR8 and Xnity Remote. SET-TOP BOXES AND DTASThe XR8 can be used for out-of-sight control with the set-top boxes and DTAs listed below:XFINITY REMOTESXnity Remotes that can be paired with the XR8 include: XR2XR5XR11XR13For additional information about Xnity Remotes visit xnity.com/remotes.

Navigation menu