Universal Electronics 5550 UEI RF4CE USB Dongle 2012 User Manual Pairing insturctions 03
Universal Electronics Inc UEI RF4CE USB Dongle 2012 Pairing insturctions 03
User Manual
USB USB
PAIR
Remote and RF Adapter PairingRemote and RF Adapter Pairing
1Insert RF Adapter into an open USB port
Insert RF Adapter into an open USB port 2Press the PAIR button on the RF adapter
Press the PAIR button on the RF adapter
3Press and hold SETUP and NAVIGATE UP
buttons simultaneously for 3 seconds
Press and hold SETUP and NAVIGATE UP
buttons simultaneously for 3 seconds
4The POWER key on the remote will blink
rapidly while the remote is in RF pairing mode
The POWER key on the remote will blink
rapidly while the remote is in RF pairing mode
5If pairing is successful, the POWER
key on the remote will blink twice
If pairing is successful, the POWER
key on the remote will blink twice If pairing is not successful, repeat steps 2-5..
Si el televisor no se apaga, repita este proceso
utilizando el siguiente código para su marca
de TV.
IN ORDER FOR THE REMOTE CONTROL AND RF ADAPTER TO COMMUNICATE, THEY MUST BE PAIRED.
FOLLOW THE INSTRUCTIONS BELOW TO PAIR THE KEYBOARD REMOTE CONTROL WITH THE RF ADAPTER.
IN ORDER FOR THE REMOTE CONTROL AND RF ADAPTER TO COMMUNICATE, THEY MUST BE PAIRED.
FOLLOW THE INSTRUCTIONS BELOW TO PAIR THE KEYBOARD REMOTE CONTROL WITH THE RF ADAPTER.
©Copyright Universal Electronics 2012
PAIR PAIR
1With the RF Adapter plugged into a USB port and powered on, press and hold the PAIR button
for 5 seconds until the LED blinks 4 times.
With the RF Adapter plugged into a USB port and powered on, press and hold the PAIR button
for 5 seconds until the LED blinks 4 times.
Clear Pairing InformationClear Pairing Information
YOU MAY HAVE TO CLEAR PAIRING INFORMATION IF YOU WISH CREATE A NEW REMOTE/RF ADAPTER PAIRING.
HERE IS HOW TO CLEAR PAIRING INFORMATION ON THE RF ADAPTER AND REMOTE.
YOU MAY HAVE TO CLEAR PAIRING INFORMATION IF YOU WISH CREATE A NEW REMOTE/RF ADAPTER PAIRING.
HERE IS HOW TO CLEAR PAIRING INFORMATION ON THE RF ADAPTER AND REMOTE.
2Press and hold SETUP and NAV DOWN on
the remote control simultaneously until the
POWER button blinks four times to
conrm pairing information has been cleared.
Press and hold SETUP and NAV DOWN on
the remote control simultaneously until the
POWER button blinks four times to
conrm pairing information has been cleared.
©Copyright Universal Electronics 2012
Federal Communication Commission Interference Statement:
This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment o
and on, the user is encouraged to try to correct the interference by one of the
following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) This device may not cause harmful interference,
and (2) this device must accept any interference received, including
interference that may cause undesired operation.
The user is cautioned that changes and modications made to the equipment
without the approval of manufacturer could void the user's authority to
operate this equipment
Industry Canada statement: This device complies with RSS-210 of the Industry
Canada Rules. Operation is subject to the following two conditions: (1) this
device may not cause harmful interference, and (2) this device must accept
any interference received, including interference that may cause undesired
operation.
Ce dispositif est conforme à la norme CNR-210 d’Industrie Canada applicable
aux appareils radio exempts de licence. Son fonctionnement est sujet aux
deux conditions suivantes: (1) le dispositif ne doit pas produire de brouillage
préjudiciable, et (2) ce dispositif doit accepter tout brouillage reçu, y compris
un brouillage susceptible de provoquer un fonctionnement indésirable.