Universal Electronics R32040 Technicolor Denali BLE OTT RCU 2018 User Manual

Universal Electronics Inc Technicolor Denali BLE OTT RCU 2018

User Manual

TechnicolorDenaliBLEOTTRCU2018
QuickStartGuide
Operating Frequency RF power Transmitter Technology
2402 to 2480 MHz 8.63 dBm max conducted BLE GSFS modulation
AutoPairingMode
Outoftheboxandwithbatteriesinserted,theRCUshallenterintoauto‐pairingmode,as
longastheRCUhasnopairinginformationstoredinmemory.
ThefeedbackLEDwillstartblinkingrapidly,indicatingthattheremoteisinpairingmode.
TheremoteshallfirstsendoutanIRcodeincasetheSTBsupportsIRassistedpairing.In
casetheSTBdoesn’tsupportIRassistedpairing,theSTBshallignoretheIRcode.
AftersendingtheIRcodeforpairing,theremoteshallstarttransmittinggeneralBLE
advertisement(ADV_IND)packetswithanadvertisementintervalofPAIR_ADV_INTERVAL
andrepeatedlytransmitsforuptoPAIR_ADV_DURATION.Ifnoconnectionisestablished
asaresultoftheadvertising,theRCUreturnstodeepsleepstateafter
PAIR_ADV_DURATION(refertosection8.4.6.1).
Iftheremotedoesn’tpairwiththehostduringthefirst60secorPAIR_ADV_DURATION,
theremoteshallgotosleepandstopadvertising.
ManualPairingMode
Towakeuptheremotetoenteritbackintopairing,theuserwouldhavetopressthekey
combinationPlay/PauseandHomeforatleast3sec.
Onceinpairingmode,theremotewillfirstsendoutanIRcommandtothetargetSTBto
putitintopairingmode.IfthetargetdevicedoesnotsupportIRassistedpairing,itshall
ignoretheIRcode.
AftersendingtheIRcodeforpairing,theremoteshallstarttransmittinggeneralBLE
advertisement(ADV_IND)packetswithanadvertisementintervalofPAIR_ADV_INTERVAL
andrepeatedlytransmitsforuptoPAIR_ADV_DURATION.Ifnoconnectionisestablished
asaresultoftheadvertising,theRCUreturnstodeepsleepstateafter
PAIR_ADV_DURATION(refertosection8.4.6.1).
Iftheremotedoesn’tpairwiththehostduringthefirst60secorPAIR_ADV_DURATION,
theremoteshallgotosleepandstopadvertising.
ManualUn‐Pairing
If the RCU is paired and the user is simultaneously pressing and holding the keys Play/Pause and
Back for at least 3 seconds, the pairing information will be deleted. If necessary, the RF link
should be disconnected. Below is the sequence of operations that needs to be executed –
TheRCUshouldinitiatealinkdisconnection(terminatelink)ifthereisanyactive
connection
RCUshouldmakeanattempttodisconnectcleanlyandifitfails,theRCUshouldforcethe
linkdisconnection
Deletethepairinginformation
The RCU should also send the un-pairing message to STB so that the STB can remove the pairing
entry. QuickSet and UAPI related features should be reset after this operation is performed. The
RCU will revert default IR state. If there are any Universal TV or Audio codes already setup, they
will remain unchanged. If the user wishes to go back to the BLE mode, the user will need to re-pair
according to section.
CustomerReset/FeatureReset
This feature clears the RAM and heap memory, and performs a soft reset. It will reset the remote
control features except the pairing information.
1. PressandholdError!Referencesourcenotfound.untilthefeedbackLEDblinkstwice.
2. Enter977toinitiatefeaturereset
3. ThefeedbackLEDwilldisplayfourblinkstoindicateasuccessfulreset.
COMPLIANCEWITHFCCRULESANDREGULATIONS
ThisequipmenthasbeentestedandfoundtocomplywiththelimitsforaClassBdigitaldevice,
pursuanttopart15oftheFCCRules.Theselimitsaredesignedtoprovidereasonableprotection
againstharmfulinterferenceinaresidentialinstallation.
Thisequipmentgeneratesusesandcanradiateradiofrequencyenergyandifnotusedin
accordancewiththeinstructions,maycauseharmfulinterferencetoradiocommunications.
However,thereisnoguaranteethatinterferencewillnotoccurinaparticularinstallation.Ifthis
equipmentdoescauseharmfulinterferencetoradioortelevisionreception,theuseris
encouragedtotrytocorrecttheinterferencebyoneormoreofthefollowingmeasures:
•Reorientorrelocatethereceivingantenna.
•Increaseordecreasetheseparationbetweentheequipmentandreceiver.
• Connecttheequipmentintoanoutletdifferentfromthattowhichthereceiveris
connected.
Consultthedealeroranexperiencedremotecontrol/TVtechnicianforhelp.
ThisequipmenthasbeenverifiedtocomplywiththelimitsforaClassBcomputingdevice,
pursuanttoFCCRules.Theuseriscautionedthatchangesandmodificationsmadetothe
equipmentwithouttheapprovalofmanufacturercouldvoidtheuser'sauthoritytooperatethis
equipment.
FCCAuthorizationLabel
Thisdevicecomplieswithpart15oftheFCCRules.Operationissubjecttothefollowingtwo
conditions:
1. Thisdevicemaynotcauseharmfulinterference.
2Thisdevicemustacceptanyinterferencereceived,includinginterferencethatmaycause
undesiredoperation.
IC Statement (English and French):
This device complies with ISED Canada licence-exempt RSS standard(s). Operation is subject to
the following two conditions: (1) this device may not cause interference, and (2) this device must
accept any interference, including interference that may cause undesired operation of the device.
Le présent appareil est conforme aux CNR d'ISED Canada applicables aux appareils radio exempts
de licence. L'exploitation est autorisée aux deux conditions suivantes: (1) l'appareil ne doit pas
produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radio électrique
subi, même si le brouillage est susceptible d'en comprom-ettre le fonctionnement.

Navigation menu