Universal Electronics R32040 Technicolor Denali BLE OTT RCU 2018 User Manual

Download:
Mirror Download [FCC.gov]
Document ID	3967598
Application ID	h33Av27MOhVBUg/Vmy8GfQ==
Document Description	User Manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	29.03kB (362855 bits)
Date Submitted	2018-08-17 00:00:00
Date Available	2018-08-17 00:00:00
Creation Date	2018-08-03 17:32:15
Producing Software	Acrobat Distiller 18.0 (Windows)
Document Lastmod	2018-08-09 15:49:06
Document Title	Microsoft Word - Technicolor Denali Quick Start Guide Rev1.0.docx
Document Creator	PScript5.dll Version 5.2.2
Document Author:	jmendez

Technicolor Denali BLE OTT RCU 2018
Quick Start Guide
Operating Frequency
RF power
Transmitter Technology
2402 to 2480 MHz
8.63 dBm max conducted
BLE GSFS modulation
Auto Pairing Mode





Out of the box and with batteries inserted, the RCU shall enter into auto‐pairing mode, as
long as the RCU has no pairing information stored in memory.
The feedback LED will start blinking rapidly, indicating that the remote is in pairing mode.
The remote shall first send out an IR code in case the STB supports IR assisted pairing. In
case the STB doesn’t support IR assisted pairing, the STB shall ignore the IR code.
After sending the IR code for pairing, the remote shall start transmitting general BLE
advertisement (ADV_IND) packets with an advertisement interval of PAIR_ADV_INTERVAL
and repeatedly transmits for up to PAIR_ADV_DURATION. If no connection is established
as a result of the advertising, the RCU returns to deep sleep state after
PAIR_ADV_DURATION (refer to section 8.4.6.1).
If the remote doesn’t pair with the host during the first 60sec or PAIR_ADV_DURATION,
the remote shall go to sleep and stop advertising.
Manual Pairing Mode




To wake up the remote to enter it back into pairing, the user would have to press the key
combination Play/Pause and Home for at least 3 sec.
Once in pairing mode, the remote will first send out an IR command to the target STB to
put it into pairing mode. If the target device does not support IR assisted pairing, it shall
ignore the IR code.
After sending the IR code for pairing, the remote shall start transmitting general BLE
advertisement (ADV_IND) packets with an advertisement interval of PAIR_ADV_INTERVAL
and repeatedly transmits for up to PAIR_ADV_DURATION. If no connection is established
as a result of the advertising, the RCU returns to deep sleep state after
PAIR_ADV_DURATION (refer to section 8.4.6.1).
If the remote doesn’t pair with the host during the first 60sec or PAIR_ADV_DURATION,
the remote shall go to sleep and stop advertising.
Manual Un‐Pairing
If the RCU is paired and the user is simultaneously pressing and holding the keys Play/Pause and
Back for at least 3 seconds, the pairing information will be deleted. If necessary, the RF link
should be disconnected. Below is the sequence of operations that needs to be executed –


The RCU should initiate a link disconnection (terminate link) if there is any active
connection
RCU should make an attempt to disconnect cleanly and if it fails, the RCU should force the
link disconnection

Delete the pairing information
The RCU should also send the un-pairing message to STB so that the STB can remove the pairing
entry. QuickSet and UAPI related features should be reset after this operation is performed. The
RCU will revert default IR state. If there are any Universal TV or Audio codes already setup, they
will remain unchanged. If the user wishes to go back to the BLE mode, the user will need to re-pair
according to section.
Customer Reset/Feature Reset
This feature clears the RAM and heap memory, and performs a soft reset. It will reset the remote
control features except the pairing information.
1. Press and hold Error! Reference source not found. until the feedback LED blinks twice.
2. Enter 977 to initiate feature reset
3. The feedback LED will display four blinks to indicate a successful reset.
COMPLIANCE WITH FCC RULES AND REGULATIONS
This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation.
This equipment generates uses and can radiate radio frequency energy and if not used in
accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television reception, the user is
encouraged to try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase or decrease the separation between the equipment and receiver.
• Connect the equipment into an outlet different from that to which the receiver is
connected.
 Consult the dealer or an experienced remote control/ TV technician for help.
This equipment has been verified to comply with the limits for a Class B computing device,
pursuant to FCC Rules. The user is cautioned that changes and modifications made to the
equipment without the approval of manufacturer could void the user's authority to operate this
equipment.
FCC Authorization Label
This device complies with part 15 of the FCC Rules. Operation is subject to the following two
conditions:
1. This device may not cause harmful interference.
2 This device must accept any interference received, including interference that may cause
undesired operation.
IC Statement (English and French):
This device complies with ISED Canada licence-exempt RSS standard(s). Operation is subject to
the following two conditions: (1) this device may not cause interference, and (2) this device must
accept any interference, including interference that may cause undesired operation of the device.
Le présent appareil est conforme aux CNR d'ISED Canada applicables aux appareils radio exempts
de licence. L'exploitation est autorisée aux deux conditions suivantes: (1) l'appareil ne doit pas
produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radio électrique
subi, même si le brouillage est susceptible d'en comprom-ettre le fonctionnement.

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.5
Linearized                      : No
Author                          : jmendez
Create Date                     : 2018:08:03 17:32:15-07:00
Modify Date                     : 2018:08:09 15:49:06-07:00
Has XFA                         : No
XMP Toolkit                     : Adobe XMP Core 5.6-c015 84.159810, 2016/09/10-02:41:30
Creator Tool                    : PScript5.dll Version 5.2.2
Metadata Date                   : 2018:08:09 15:49:06-07:00
Producer                        : Acrobat Distiller 18.0 (Windows)
Format                          : application/pdf
Title                           : Microsoft Word - Technicolor Denali Quick Start Guide Rev1.0.docx
Creator                         : jmendez
Document ID                     : uuid:492047c7-560c-41f1-9725-c88ef3a28993
Instance ID                     : uuid:e29ce67e-69d2-467c-9298-e541d2f9eb42
Page Count                      : 4

EXIF Metadata provided by EXIF.tools