Universal Global Scientific NFABACMR02 802.11ac/a/b/g/n + BT Wireless Module User Manual
Universal Global Scientific Industrial Co., Ltd. 802.11ac/a/b/g/n + BT Wireless Module
Contents
- 1. User Manual.pdf
- 2. User Manual
- 3. User Manual statement
- 4. User Manual Statement
User Manual.pdf
Wireless Product Business Unit/
Research & Development Division
The content of this document is to be treated as strictly confidential and is not to be disclosed, reproduced or used,
except as authorized in writing by Universal Global Scientific Industrial Co., Ltd. Copyright © 2010 Universal Global
Scientific Industrial Co., Ltd.
User Guide
of
NFA-BAC-MR-02
SOURCE ORGANIZATION: USI WP/ RD/ HW
Prepared by Terry Hua Date: 2014/02/05
Checked by Date:
Approved by Date:
Concurrence Date:
Document
No. Rev.
1.0
Product No.
Product Code
Model
No.
NFA
-
BAC
-
MR
-
02
Universal Global Scientific Industrial Co., Ltd.
Doc No.
Rev 1.0
Document released by
WP/ RD/ HW
Date.
2014/02/05
Page 2
Description EVB User Guide of NFA-BAC-MR-02
The content of this document is to be treated as strictly confidential and is not to be disclosed, reproduced or used,
except as authorized in writing by Universal Global Scientific Industrial Co., Ltd. Copyright © 2010 Universal Global
Scientific Industrial Co., Ltd.
Change Sheet
Rev.
Date Description of change Approval & Date
Page Par Change(s)
1.0 2014/02/05
All All Initial Version
Universal Global Scientific Industrial Co., Ltd.
Doc No.
Rev 1.0
Document released by
WP/ RD/ HW
Date.
2014/02/05
Page 3
Description EVB User Guide of NFA-BAC-MR-02
The content of this document is to be treated as strictly confidential and is not to be disclosed, reproduced or used,
except as authorized in writing by Universal Global Scientific Industrial Co., Ltd. Copyright © 2010 Universal Global
Scientific Industrial Co., Ltd.
Table of Contents
1. Introduction ................................................................................ 4
2. Testing Environment Setup....................................................... 4
3. TX Command for Measurement ................................................ 5
4. RX Command for Measurement................................................ 6
Universal Global Scientific Industrial Co., Ltd.
Doc No.
Rev 1.0
Document released by
WP/ RD/ HW
Date.
2014/02/05
Page 4
Description EVB User Guide of NFA-BAC-MR-02
The content of this document is to be treated as strictly confidential and is not to be disclosed, reproduced or used,
except as authorized in writing by Universal Global Scientific Industrial Co., Ltd. Copyright © 2010 Universal Global
Scientific Industrial Co., Ltd.
1. Introduction
This EVB is an interface transfer card for NFA-BAC-MR-02 NGFF Card. The NGFF
card is built in 802.11 a/b/g/n/ac and Bluetooth function. The EVB
will transfer NGFF interface
to PCI express card interface for inserting the Testing PC
2. Testing Environment Setup
Universal Global Scientific Industrial Co., Ltd.
Doc No.
Rev 1.0
Document released by
WP/ RD/ HW
Date.
2013/12/04
Page 5
Description EVB User Guide of NFB-BAC-MR-02
The content of this document is to be treated as strictly confidential and is not to be disclosed, reproduced or used,
except as authorized in writing by Universal Global Scientific Industrial Co., Ltd. Copyright © 2010 Universal Global
Scientific Industrial Co., Ltd.
3. TX Command for Measurement
Universal Global Scientific Industrial Co., Ltd.
Doc No.
Rev 1.0
Document released by
WP/ RD/ HW
Date.
2013/12/04
Page 6
Description EVB User Guide of NFB-BAC-MR-02
The content of this document is to be treated as strictly confidential and is not to be disclosed, reproduced or used,
except as authorized in writing by Universal Global Scientific Industrial Co., Ltd. Copyright © 2010 Universal Global
Scientific Industrial Co., Ltd.
4. RX Command for Measurement
Universal Global Scientific Industrial Co., Ltd.
Doc No.
Rev 1.0
Document released by
WP/ RD/ HW
Date.
2013/12/04
Page 7
Description EVB User Guide of NFB-BAC-MR-02
The content of this document is to be treated as strictly confidential and is not to be disclosed, reproduced or used,
except as authorized in writing by Universal Global Scientific Industrial Co., Ltd. Copyright © 2010 Universal Global
Scientific Industrial Co., Ltd.
Industry Canada statement
This device complies with RSS-210 of the Industry Canada Rules. Operation is subject to the following two
conditions: (1) This device may not cause harmful interference, and (2)this device must accept any
interference received, including interference that may cause undesired operation.
Ce dispositif est conforme à la norme CNR-210 d'Industrie Canada applicable aux
appareils radio exempts de licence. Son fonctionnement est sujet aux deux conditions
suivantes: (1) le dispositif ne doit pas produire de brouillage préjudiciable, et (2) ce
dispositif doit accepter tout brouillage reçu, y compris un brouillage susceptible de
provoquer un fonctionnement indésirable.
Radiation Exposure Statement:
This equipment complies with IC radiation exposure limits set forth for an uncontrolled environment. This
equipment should be installed and operated with minimum distance 20cm between the radiator & your body.
Déclaration d'exposition aux radiations:
Cet équipement est conforme aux limites d'exposition aux rayonnements IC établies pour un environnement
non contrôlé. Cet équipement doit être installé et utilisé avec un minimum de 20 cm de distance entre la
source de rayonnement et votre corps.
This device is intended only for OEM integrators under the following conditions:
(For module device use)
1) The antenna must be installed such that 20 cm is maintained between the antenna and users, and 2) The
transmitter module may not be co-located with any other transmitter or antenna.
As long as 2 conditions above are met, further transmitter test will not be required.
However, the OEM integrator is still responsible for testing their end-product for any
additional compliance requirements required with this module installed.
Cet appareil est conçu uniquement pour les intégrateurs OEM dans les conditions
suivantes: (Pour utilisation de dispositif module)
1) L'antenne doit être installée de telle sorte qu'une distance de 20 cm est respectée entre l'antenne et les
utilisateurs, et 2) Le module émetteur peut ne pas être coïmplanté avec un autre émetteur ou antenne.
Tant que les 2 conditions ci-dessus sont remplies, des essais supplémentaires sur
l'émetteur ne seront pas nécessaires. Toutefois, l'intégrateur OEM est toujours
responsable des essais sur son produit final pour toutes exigences de conformité
supplémentaires requis pour ce module installé.
IMPORTANT NOTE:
In the event that these conditions can not be met (for example certain laptop configurations or co-location with
another transmitter), then the Canada authorization is no longer considered valid and the IC ID can not be
Universal Global Scientific Industrial Co., Ltd.
Doc No.
Rev 1.0
Document released by
WP/ RD/ HW
Date.
2013/12/04
Page 8
Description EVB User Guide of NFB-BAC-MR-02
The content of this document is to be treated as strictly confidential and is not to be disclosed, reproduced or used,
except as authorized in writing by Universal Global Scientific Industrial Co., Ltd. Copyright © 2010 Universal Global
Scientific Industrial Co., Ltd.
used on the final product. In these circumstances, the OEM integrator will be responsible for re-evaluating the
end product(including the transmitter) and obtaining a separate Canada authorization.
NOTE IMPORTANTE:
Dans le cas où ces conditions ne peuvent être satisfaites (par exemple pour certaines
configurations d'ordinateur portable ou de certaines co-localisation avec un autre
émetteur), l'autorisation du Canada n'est plus considéré comme valide et l'ID IC ne peut pas être utilisé sur le
produit final. Dans ces circonstances, l'intégrateur OEM sera chargé de réévaluer le produit final (y compris
l'émetteur) et l'obtention d'une autorisation distinct au Canada.
End Product Labeling
This transmitter module is authorized only for use in device where the antenna may be
installed such that 20 cm may be maintained between the antenna and users. The final
end product must be labeled in a visible area with the following: “Contains IC: 10293A-NFABACMR02”.
Plaque signalétique du produit final
Ce module émetteur est autorisé uniquement pour une utilisation dans un dispositif où
l'antenne peut être installée de telle sorte qu'une distance de 20cm peut être maintenue
entre l'antenne et les utilisateurs. Le produit final doit être étiqueté dans un endroit visible avec l'inscription
suivante: "Contient des IC: 10293A-NFABACMR02".
Manual Information To the End User
The OEM integrator has to be aware not to provide information to the end user regarding how to install or
remove this RF module in the user’s manual of the end product which integrates this module.
The end user manual shall include all required regulatory information/warning as show in this manual.
Manuel d'information à l'utilisateur final
L'intégrateur OEM doit être conscient de ne pas fournir des informations à l'utilisateur final quant à la façon
d'installer ou de supprimer ce module RF dans le manuel de l'utilisateur du produit final qui intègre ce module.
Le manuel de l'utilisateur final doit inclure toutes les informations réglementaires requises et avertissements
comme indiqué dans ce manuel.
Warming
Caution :
(i) the device for operation in the band 5150-5250 MHz is only for indoor use to reduce the potential for
harmful interference to co-channel mobile satellite systems;
(ii) the maximum antenna gain permitted for devices in the bands 5250-5350 MHz and 5470-5725 MHz shall
comply with the e.i.r.p. limit; and
Universal Global Scientific Industrial Co., Ltd.
Doc No.
Rev 1.0
Document released by
WP/ RD/ HW
Date.
2013/12/04
Page 9
Description EVB User Guide of NFB-BAC-MR-02
The content of this document is to be treated as strictly confidential and is not to be disclosed, reproduced or used,
except as authorized in writing by Universal Global Scientific Industrial Co., Ltd. Copyright © 2010 Universal Global
Scientific Industrial Co., Ltd.
(iii) the maximum antenna gain permitted for devices in the band 5725-5825 MHz shall comply with the e.i.r.p.
limits specified for point-to-point and non point-to-point operation as appropriate.
(iv) Users should also be advised that high-power radars are allocated as primary users (i.e. priority users) of
the bands 5250-5350 MHz and 5650-5850 MHz and that these radars could cause interference and/or
damage to LE-LAN devices.
Avertissement:
Le guide d’utilisation des dispositifs pour réseaux locaux doit inclure des instructions précises sur les
restrictions susmentionnées, notamment :
(i) les dispositifs fonctionnant dans la bande 5 150-5 250 MHz sont réservés uniquement pour une utilisation à
l’intérieur afin de réduire les risques de brouillage préjudiciable aux systèmes de satellites mobiles utilisant les
mêmes canaux;
(ii) le gain maximal d’antenne permis pour les dispositifs utilisant les bandes 5 250-5 350 MHz et 5 470-5 725
MHz doit se conformer à la limite de p.i.r.e.;
(iii) le gain maximal d’antenne permis (pour les dispositifs utilisant la bande 5 725-5 825 MHz) doit se
conformer à la limite de p.i.r.e. spécifiée pour l’exploitation point à point et non point à point, selon le cas.
(iv) De plus, les utilisateurs devraient aussi être avisés que les utilisateurs de radars de haute puissance sont
désignés utilisateurs principaux (c.-à-d., qu’ils ont la priorité) pour les bandes 5 250-5 350 MHz et 5 650-5 850
MHz et que ces radars pourraient causer du brouillage et/ou des dommages aux dispositifs LAN-EL.
Universal Global Scientific Industrial Co., Ltd.
Doc No.
Rev 1.0
Document released by
WP/ RD/ HW
Date.
2013/12/04
Page 10
Description EVB User Guide of NFB-BAC-MR-02
The content of this document is to be treated as strictly confidential and is not to be disclosed, reproduced or used,
except as authorized in writing by Universal Global Scientific Industrial Co., Ltd. Copyright © 2010 Universal Global
Scientific Industrial Co., Ltd.
Federal Communication Commission Interference Statement
This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) This device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that
may cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio frequency energy
and, if not installed and used in accordance with the instructions, may cause
harmful interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the
interference by one of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that
to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
FCC Caution: Any changes or modifications not expressly approved by the party
responsible for compliance could void the user's authority to operate this equipment.
This transmitter must not be co-located or operating in conjunction with any other
antenna or transmitter.
Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environment. This equipment should be installed and operated with
minimum distance 20cm between the radiator & your body.
This device is intended only for OEM integrators under the following conditions:
1) The antenna must be installed such that 20 cm is maintained between the antenna
and users, and 2) The transmitter module may not be co-located with any other transmitter or antenna.
As long as 2 conditions above are met, further transmitter test will not be required.
However, the OEM integrator is still responsible for testing their end-product for any
additional compliance requirements required with this module installed
IMPORTANT NOTE: In the event that these conditions can not be met (for example
Universal Global Scientific Industrial Co., Ltd.
Doc No.
Rev 1.0
Document released by
WP/ RD/ HW
Date.
2013/12/04
Page 11
Description EVB User Guide of NFB-BAC-MR-02
The content of this document is to be treated as strictly confidential and is not to be disclosed, reproduced or used,
except as authorized in writing by Universal Global Scientific Industrial Co., Ltd. Copyright © 2010 Universal Global
Scientific Industrial Co., Ltd.
certain laptop configurations or co-location with another transmitter), then the FCC
authorization is no longer considered valid and the FCC ID can not be used on the
final product. In these circumstances, the OEM integrator will be responsible for reevaluating the end product
(including the transmitter) and obtaining a separate FCC
authorization.
End Product Labeling
This transmitter module is authorized only for use in device where the antenna may be
installed such that 20 cm may be maintained between the antenna and users. The
final end product must be labeled in a visible area with the following: “Contains FCC
ID: COFNFABACMR02”. The grantee's FCC ID can be used only when all FCC compliance requirements are
met.
Manual Information To the End User
The OEM integrator has to be aware not to provide information to the end user
regarding how to install or remove this RF module in the user’s manual of the end
product which integrates this module.
The end user manual shall include all required regulatory information/warning as show in this manual.
Warming
Operations in the 5.15-5.25GHz band are restricted to indoor usage only.
Universal Global Scientific Industrial Co., Ltd.
Doc No.
Rev 1.0
Document released by
WP/ RD/ HW
Date.
2013/12/04
Page 12
Description EVB User Guide of NFB-BAC-MR-02
The content of this document is to be treated as strictly confidential and is not to be disclosed, reproduced or used,
except as authorized in writing by Universal Global Scientific Industrial Co., Ltd. Copyright © 2010 Universal Global
Scientific Industrial Co., Ltd.
Europe – EU Declaration of Conformity
This device complies with the essential requirements of the R&TTE Directive 1999/5/EC. The
following test methods have been applied in order to prove presumption of conformity with the
essential requirements of the R&TTE Directive 1999/5/EC:
EN 60950-1: 2006+A11:2009+A1:2010+A12:2011
EN 62311:2008
EN300 328 V 1.8.1:2012
EN 301 489-1 V1.9.2:2011
EN 301 489-17 V 2.2.1 :2012
National Authorities were informed according to Article 6.4 of Frequency Notification.
Special Requirements are considered. The product is labeled with CE Marking.
Česky
[Czech] [Jméno výrobce] tímto prohlašuje, že tento [typ zařízení] je ve shodě se základními
požadavky a dalšími příslušnými ustanoveními směrnice 1999/5/ES.
Dansk
[Danish] Undertegnede [fabrikantens navn] erklærer herved, at følgende udstyr [udstyrets
typebetegnelse] overholder de væsentlige krav og øvrige relevante krav i direktiv
1999/5/EF.
Deutsch
[German] Hiermit erklärt [Name des Herstellers], dass sich das Gerät [Gerätetyp] in
Übereinstimmung mit den grundlegenden Anforderungen und den übrigen
einschlägigen Bestimmungen der Richtlinie 1999/5/EG befindet.
Eesti
[Estonian] Käesolevaga kinnitab [tootja nimi = name of manufacturer] seadme [seadme tüüp = type
of equipment] vastavust direktiivi 1999/5/EÜ põhinõuetele ja nimetatud direktiivist
tulenevatele teistele asjakohastele sätetele.
English Hereby, [name of manufacturer], declares that this [type of equipment] is in compliance
with the essential requirements and other relevant provisions of Directive 1999/5/EC.
Español
[Spanish] Por medio de la presente [nombre del fabricante] declara que el [clase de equipo]
cumple con los requisitos esenciales y cualesquiera otras disposiciones aplicables o
exigibles de la Directiva 1999/5/CE.
Ελληνική
[Greek] ΜΕ ΤΗΝ ΠΑΡΟΥΣΑ [name of manufacturer] ∆ΗΛΩΝΕΙ ΟΤΙ [type of equipment]
ΣΥΜΜΟΡΦΩΝΕΤΑΙ ΠΡΟΣ ΤΙΣ ΟΥΣΙΩ∆ΕΙΣ ΑΠΑΙΤΗΣΕΙΣ ΚΑΙ ΤΙΣ ΛΟΙΠΕΣ ΣΧΕΤΙΚΕΣ
∆ΙΑΤΑΞΕΙΣ ΤΗΣ Ο∆ΗΓΙΑΣ 1999/5/ΕΚ.
Français
[French] Par la présente [nom du fabricant] déclare que l'appareil [type d'appareil] est conforme
aux exigences essentielles et aux autres dispositions pertinentes de la directive
1999/5/CE.
Italiano Con la presente [nome del costruttore] dichiara che questo [tipo di apparecchio] è
Universal Global Scientific Industrial Co., Ltd.
Doc No.
Rev 1.0
Document released by
WP/ RD/ HW
Date.
2013/12/04
Page 13
Description EVB User Guide of NFB-BAC-MR-02
The content of this document is to be treated as strictly confidential and is not to be disclosed, reproduced or used,
except as authorized in writing by Universal Global Scientific Industrial Co., Ltd. Copyright © 2010 Universal Global
Scientific Industrial Co., Ltd.
[Italian] conforme ai requisiti essenziali ed alle altre disposizioni pertinenti stabilite dalla direttiva
1999/5/CE.
Latviski
[Latvian] Ar šo [name of manufacturer / izgatavotāja nosaukums] deklarē, ka [type of equipment
/ iekārtas tips] atbilst Direktīvas 1999/5/EK būtiskajām prasībām un citiem ar to
saistītajiem noteikumiem.
Lietuvių
[Lithuanian]
Šiuo [manufacturer name] deklaruoja, kad šis [equipment type] atitinka esminius
reikalavimus ir kitas 1999/5/EB Direktyvos nuostatas.
Nederland
s [Dutch] Hierbij verklaart [naam van de fabrikant] dat het toestel [type van toestel] in
overeenstemming is met de essentiële eisen en de andere relevante bepalingen van
richtlijn 1999/5/EG.
Malti
[Maltese] Hawnhekk, [isem tal-manifattur], jiddikjara li dan [il-mudel tal-prodott] jikkonforma
mal-ħtiġijiet essenzjali u ma provvedimenti oħrajn relevanti li hemm fid-Dirrettiva
1999/5/EC.
Magyar
[Hungarian] Alulírott, [gyártó neve] nyilatkozom, hogy a [... típus] megfelel a vonatkozó alapvetõ
követelményeknek és az 1999/5/EC irányelv egyéb elõírásainak.
Polski
[Polish] Niniejszym [nazwa producenta] oświadcza, że [nazwa wyrobu] jest zgodny z
zasadniczymi wymogami oraz pozostałymi stosownymi postanowieniami Dyrektywy
1999/5/EC.
Português
[Portuguese]
[Nome do fabricante] declara que este [tipo de equipamento] está conforme com os
requisitos essenciais e outras disposições da Directiva 1999/5/CE.
Slovensko
[Slovenian] [Ime proizvajalca] izjavlja, da je ta [tip opreme] v skladu z bistvenimi zahtevami in
ostalimi relevantnimi določili direktive 1999/5/ES.
Slovensky
[Slovak] [Meno výrobcu] týmto vyhlasuje, že [typ zariadenia] spĺňa základné požiadavky a všetky
príslušné ustanovenia Smernice 1999/5/ES.
Suomi
[Finnish] [Valmistaja = manufacturer] vakuuttaa täten että [type of equipment = laitteen
tyyppimerkintä] tyyppinen laite on direktiivin 1999/5/EY oleellisten vaatimusten ja sitä
koskevien direktiivin muiden ehtojen mukainen.
Svenska
[Swedish] Härmed intygar [företag] att denna [utrustningstyp] står I överensstämmelse med de
väsentliga egenskapskrav och övriga relevanta bestämmelser som framgår av direktiv
1999/5/EG.