Universal Scientific MESSI-V LTE Module User Manual UNA

Universal Scientific Industrial Co., Ltd. LTE Module UNA

User Manual

1/13 Rev1.2 MESSI-V M2 I/O APPLICATION 4G LTE Module (NGFF type) Doc. Title MESSI-V M2 I/O APPLICATION Originator David Tsui Concurrence Achau Lee Approved by Version Date 2013/08/08
2/13 Rev1.2 Revision History Rev Draft/Changes Date 1.0 First version released (DVT phase) 2013/01/10
3/13 Rev1.2 Introduction: MESSI-V M2 is an advanced and compact NGFF board / module which supports LTE category 3 (CAT-3) throughputs. MESSI-V M2 supports for UART, USB2.0, USIM and antenna interface. The details of I/O interfaces are described in the sections as followings:  UART Interface  USB2.0 Interface  USIM Interface  Power Input  JTAG & Reset  GPIO  Antenna Interface  Others
4/13 Rev1.2 1. UART Interface MESSI-V M2 board supports one UART port for debugging and downloading. The baud rate speed is up to 115200bps. Signal level is 3.3V. If MESSI-V M2 module goes through standard RS-232 interface to connect with PC, It is recommended to use TI TRS3253EIRSMR for best baud rate to catch log file and download boot loader setting. Pin NO. Pin name Description 62 UART_RX UART receive input 64 UART_TX UART transmit output Figure1-1: UART block diagram. Figure1-2: RS-232 connection
5/13 Rev1.2 2. USB 2.0 Interface The USB interface is compliant with Version 2.0 of the USB standard for high speed operation. The reference circuit is showing in Figure2-1as following. Pin NO. Pin name Description 7 USB_D+ Universal Serial BUS 9 USB_D- Figure2-1: USB connection
6/13 Rev1.2 3. USIM interface The USIM pins provide the connections necessary to interface to a USIM socket located on the host device. Voltage levels over this interface comply with 3GPP standards. MSEEI module outputs a SIMPWR power rail 1.8V and 3V. Pin NO. Pin name Description 36 SIMPWR 1.8V/3V output to SIM card. 34 SIMIO SIM data IO 32 SIMCLK SIM clock 30 SIMRST SIM reset The reference circuit is showing in Figure3-1as following. Figure3-1: USIM card connection
7/13 Rev1.2 4. Power Input MESSI-V M2 power input pin is VBAT. The power input range is from 3.4V to 5V with USB, external power or Battery. Figure 4-1 shows external power source to MESSI module. Pin NO. Pin name Description 2 3.3V Power input 4 3.3V 70 3.3V 72 3.3V 74 3.3V Figure4-1: External power for MESSI-V M2 board.
8/13 Rev1.2 5. JTAG & Reset Emulation JTAG is used to debug and run SW on embedded MIPS processors. MESSI has a single Reset input (RSTN). This signal should be connected and driven by the power management unit or the host application processor, depending on the usage scenario. Pin NO. Pin name Description 42 TCK Clock 43 TMS Test Mode 47 TDI Input Data 49 TDO Output Data 53 EJTAG_TRST EJTAG Reset 67 TRST MESSI Reset Input(1.8V) Figure 6-1: JTAG connection
9/13 Rev1.2 6. GPIOs MESSI-V M2 has various software-controlled general purpose IO (GPIO) pins which are listed below. The user can use these GPIOs for any general purpose their design calls for. If the GPIO is not in use, it is recommended to leave the pin as floating. Pin NO. Pin name Description 8 GPIO4 3.3V General Purpose I/O 35 GPIO20 1.8V General Purpose I/O 31 GPIO19 1.8V General Purpose I/O 29 GPIO18 1.8V General Purpose I/O 20 GPIO11 1.8V General Purpose I/O 22 GPIO10 1.8V General Purpose I/O 24 GPIO9 1.8V General Purpose I/O 26 GPIO8 1.8V General Purpose I/O 28 GPIO12 1.8V General Purpose I/O 40 GPIO13 1.8V General Purpose I/O 42 GPIO14 1.8V General Purpose I/O 44 GPIO15 1.8V General Purpose I/O 46 GPIO16 1.8V General Purpose I/O
10/13 Rev1.2 7. Antenna Interface MESSI-V M2 support MIMO antenna. The reference RF cable SPEC is down below. Pin NO. Pin name Description ANT 1 RXTX RF Transmission and RF receive chain ANT 2 RXONLY RF receive chain Figure 8-1: MIMO antenna connection
11/13 Rev1.2 8. Others The following Pins are reserved for future update. The user can leave these pin as floating. Pin NO. Pin name Description 23 PMU SLEEP/PWR_REQ Reserved 66 SCR_DTCT Reserved 9. Mechanical Outline Figure9-1: Messi-V M2 Mechanical
12/13 Rev1.2 Federal Communication Commission Interference Statement This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures: - Reorient or relocate the receiving antenna. - Increase the separation between the equipment and receiver. - Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. - Consult the dealer or an experienced radio/TV technician for help. FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.
13/13 Rev1.2 Radiation Exposure Statement: This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body. This device is intended only for OEM integrators under the following conditions: 1) The antenna must be installed such that 20 cm is maintained between the antenna and users, and 2) The transmitter module may not be co-located with any other transmitter or antenna. IMPORTANT NOTE: In the event that these conditions can not be met (for example certain laptop configurations or co-location with another transmitter), then the FCC authorization is no longer considered valid and the FCC ID can not be used on the final product. In these circumstances, the OEM integrator will be responsible for re-evaluating the end product (including the transmitter) and obtaining a separate FCC authorization. End Product Labeling This transmitter module is authorized only for use in device where the antenna may be installed such that 20 cm may be maintained between the antenna and users. The final end product must be labeled in a visible area with the following: “Contains FCC ID: IXMMESSI-V”. The grantee's FCC ID can be used only when all FCC compliance requirements are met. Manual Information To the End User The OEM integrator has to be aware not to provide information to the end user regarding how to install or remove this RF module in the user’s manual of the end product which integrates this module. The end user manual shall include all required regulatory information/warning as show in this manual.

Navigation menu