Universal Scientific UGNAS-P3 NETWORK ATTACHED STORAGE User Manual User guide for P2 V1 1 01 28
Universal Scientific Industrial Co., Ltd. NETWORK ATTACHED STORAGE User guide for P2 V1 1 01 28
USERS MANUAL
| Download: |  |
| Mirror Download [FCC.gov] | |
| Document ID | 1512779 |
| Application ID | aH5enRgAz4hzjZ9dDYxmQQ== |
| Document Description | USERS MANUAL |
| Short Term Confidential | No |
| Permanent Confidential | No |
| Supercede | No |
| Document Type | User Manual |
| Display Format | Adobe Acrobat PDF - pdf |
| Filesize | 8.03kB (100401 bits) |
| Date Submitted | 2011-07-29 00:00:00 |
| Date Available | 2012-01-25 00:00:00 |
| Creation Date | 2011-07-21 10:27:27 |
| Producing Software | Acrobat Distiller 7.0 (Windows) |
| Document Lastmod | 2011-07-28 10:12:00 |
| Document Title | User guide for P2 _V1.1_01_28 |
| Document Creator | PScript5.dll Version 5.2 |
| Document Author: | Roger |
Topkick1281P2 User Guide Network-Attached Storage User Guide Version 1.1 1. Firmware Images Layout The u-boot image is about 512KB and located in the NAND or SPI flash between 0 and 0x0100000, be careful to erase it when update new u-boot. And layout of firmware images on NAND flash is as follows Note: Please DO NOT erase the UBoot space if it is not necessary Image Offset Size U-boot 0x0 0x100000 U-boot environment 0x180000 0x20000 Kernel 0x200000 0x600000 File system (Initrd) 0x800000 0x1000000 Table 1-1: Firmware NAND Flash Layout 2. Network Service The eth0 static IP is 192.168.58.100. The wireless AP’s static IP is 192.168.1.1. The AP’s SSID is Network-Attached and Storage-AP-* and it has no encryption. is Topkick1281P2-AP-* it has no encryption. The default network services on the board are Samba, FTP and Telnet. Username and password for Samba and Telnet’s are root:root. Username and password for Ftp is admin:admin. 3. How to Boot From SATA Disk The default u-boot bootcmd is “bootcmd=nand read.e 0x1200000 0x200000 0x600000;nand read.e 0x2000000 0x800000 0x1000000;bootm 0x1200000 0x2000000” and the bootargs valuable is “bootargs=console=ttyS0,115200” If you want to port the root filesystem to sata disk partition please type the command below in U-boot environment, which can be modified on your demand. Marvell>> setenv bootargs 'console=ttyS0,115200 root=/dev/sda1 rw' Marvell>> setenv bootcmd 'nand read.e 0x1200000 0x200000 0x600000;bootm 0x1200000' Marvell>> save Marvell>> boot 4. How to Boot From USB Disk The default u-boot bootcmd is “bootcmd=nand read.e 0x1200000 0x200000 0x600000;nand read.e 0x2000000 0x800000 0x1000000;bootm 0x1200000 0x2000000” and the bootargs valuable is “bootargs=console=ttyS0,115200” If you want to port the root filesystem to USB disk partition please type the command below in U-boot environment, which can be modified on your demand. Marvell>> setenv bootargs 'console=ttyS0,115200 root=/dev/sda1 rw rootdelay=10' //Note: root=/dev/sda1 can be changed to root=/dev/sdb1 or others according to USB partition name Marvell>> setenv bootcmd 'nand read.e 0x1200000 0x200000 0x600000;bootm 0x1200000' Marvell>> save Marvell>> boot 5. Programmable Function 5.1 Switch Function The switch action is detected by the daemon “pwrctl –d”. The switch has two directions. You can switch button to position A to shut down the system by script /usr/sbin/switch_off (t>2S), switch to position B to excute /usr/sbin/switch_optional which can be customized. See Figure 1-1 StorageIndication Switch Indication Figure 1-1: Network-Attached Topkick1281P2 Switch 5.2 Led Control Function The board has five LEDs and their control commands and functions are as Table 1-1: LED Function System LED Wireless LED SATA LED Led Color Light On Light Off Blink Blue pwrctl -o 502 pwrctl -o 503 pwrctl -o 504 Red pwrctl -o 602 pwrctl -o 603 pwrctl -o 604 Yellow pwrctl -o 302 pwrctl -o 303 pwrctl -o 304 Green pwrctl -o 702 pwrctl -o 703 pwrctl -o 704 Blue None None None Table 2-1: LED Control Function Table 5.3 WOL Function Network-Attached Storage system support WOL(Wake On Lan) function. The magic packet can be The topkick1281p2 sent by magic packet tool such as magpac.exe to turn on the system if the system is powered and connect to network. 5.4 WiFi Function The WiFi controller IC is sd8786 which work in AP mode. The file sd8786_uapsta.bin should be copied to /lib/firmware/mrvl/ directory. The operations to load the driver module, configure and bring up the wifi interface are as follows. / # insmod /lib/modules/mlan.ko / # insmod /lib/modules/sd8xxx.ko / # uaputl.exe sys_cfg_ssid $APNAME / # uaputl.exe bss_start / # ifconfig uap0 192.168.1.1 “uaputl.exe --help” for more details. FCC Regulations: 15.19(a)(3): This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. 15.105(b): NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: —Reorient or relocate the receiving antenna. —Increase the separation between the equipment and receiver. —Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. —Consult the dealer or an experienced radio/ TV technician for help. Changes or modifications not expressly approved by the party responsible for compliance could void the user‘s authority to operate the equipment. zThe antenna(s) used for this transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. RF Exposure Information This device meets the government’s requirements for exposure to radio waves. This device is designed and manufactured not to exceed the emission limits for exposure to radio frequency (RF) energy set by the Federal Communications Commission of the U.S. Government. zThis device complies with FCC radiation exposure limits set forth for an uncontrolled environment. In order to avoid the possibility of exceeding the FCC radio frequency exposure limits, human proximity to the antenna shall not be less than 20cm (8 inches) during normal operation.
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.6 Linearized : No Author : Roger Create Date : 2011:07:21 10:27:27+08:00 Modify Date : 2011:07:28 10:12:00+08:00 XMP Toolkit : Adobe XMP Core 4.2.1-c041 52.342996, 2008/05/07-20:48:00 Producer : Acrobat Distiller 7.0 (Windows) Metadata Date : 2011:07:28 10:12+08:00 Creator Tool : PScript5.dll Version 5.2 Thumbnail Width : 220 Thumbnail Height : 256 Thumbnail Format : JPEG Thumbnail Image : (Binary data 15348 bytes, use -b option to extract) Document ID : uuid:FF486FF040B3E011A5948D04C9A05F0F Instance ID : uuid:4ec7a017-0e6c-45be-84fc-92ea588e87d9 Derived From Instance ID : uuid:04eb562b-a76a-4db5-b6d3-36196ac24baa Derived From Document ID : uuid:46FF358E9FB2E011BB14F7659AD1BD02 N Pages : 1 Has Visible Transparency : False Has Visible Overprint : False Max Page Size W : 209.999929 Max Page Size H : 296.999959 Max Page Size Unit : Millimeters Font Name : ArialMT, TimesNewRomanPS-BoldItalicMT, TimesNewRomanPS-BoldMT, TimesNewRomanPS-ItalicMT, TimesNewRomanPSMT Font Family : Arial, Times New Roman, Times New Roman, Times New Roman, Times New Roman Font Face : Regular, Bold Italic, Bold, Italic, Regular Font Type : Open Type, Open Type, Open Type, Open Type, Open Type Font Version : Version 3.00, Version 2.90, Version 3.00, Version 2.90, Version 3.00 Font Composite : False, False, False, False, False Font File Name : ARIAL.TTF, TIMESBI.TTF, TIMESBD.TTF, TIMESI.TTF, TIMES.TTF Plate Names : Cyan, Magenta, Yellow, Black Swatch Group Name : 默认色板组 Swatch Group Type : 0 Swatch Colorant Swatch Name : AutoCAD Color, AutoCAD Color 4, AutoCAD Color 3, AutoCAD Color 1, AutoCAD Color 2, AutoCAD Color 6, AutoCAD Color 5 Swatch Colorant Type : PROCESS, PROCESS, PROCESS, PROCESS, PROCESS, PROCESS, PROCESS Swatch Colorant Tint : 100.000000, 100.000000, 100.000000, 100.000000, 100.000000, 100.000000, 100.000000 Swatch Colorant Mode : RGB, RGB, RGB, RGB, RGB, RGB, RGB Swatch Colorant Red : 0, 105, 246, 253, 111, 185, 237 Swatch Colorant Green : 0, 189, 235, 190, 204, 82, 31 Swatch Colorant Blue : 0, 69, 19, 16, 221, 158, 36 Format : application/pdf Creator : Roger Title : User guide for P2 _V1.1_01_28 Page Count : 3EXIF Metadata provided by EXIF.tools